Joy-IT JT-OR750i

* * * * * * * * * * * * * * * * * * * * * ┬─┐┌─┐┬ ┬─┬─┌─┐┬─┐ ┬ ┬ ┌┐ ┌─┐┌─┐─┬─ * * ├┬┘│ ││ │ │ ├─ ├┬┘ │ │─├┴┐│ ││ │ │ * * ┴└─└─┘└─┘ ┴ └─┘┴└─ └─┘ └─┘└─┘└─┘ ┴ * *_.-._.-._.-._.-._.-._.-._.-._.-._.-._* *._.-._.-._.-._.-._.-._.-._.-._.-._.-.* * * * ) ) > ┬ < ( ( * * _│_ * * | \ * * ._,---------' `--------. * * +_ www.MeshWRT.com ) * * ´ `-----------------------´ * * * * Router U-Boot 1.0.0-66dc425c-dirty * * Build date: 2021-03-04 * * * * * * * * * * * * * * * * * * * * * ** Warning: bad env CRC, using default, use 'saveenv' to save it in FLASH BOARD: Joy-IT JT-OR750i SOC: QCA953x ver. 2 rev. 0 CPU: MIPS 24Kc RAM: 128 MB DDR2 16-bit CL3-4-4-10 FLASH: 16 MB Macronix MX25L128 PCIe: QCA9887 MAC: 44:D1:FA:5A:0E:38 UART: 111607 bps CLOCKS: CPU/RAM/AHB/SPI/REF 550/400/200/ 25/ 25 MHz Keep the button pressed for at least: - 3s for TFTP firmware recovery using static IPs - 5s for TFTP firmware recovery using DHCP - 7s for Web recovery as DHCP client - 9s for Web recovery as DHCP server - 12s for network console . . . . .


Flashing via tftp

“3 seconds button pressed” - DHCP-adress

Starting TFTP firmware recovery using DHCP... Trying to acquire a DHCP lease... eth0 link down enet1 port3 up Random delay: 966 ms... Sending DHCP discover... 1 Received DHCP offer! New IP: 192.168.8.225 Server IP: 192.168.8.5 eth0 link down Using eth1 device Ping OK, host 192.168.8.5 is alive! eth0 link down TFTP from IP: 192.168.8.5 Our IP: 192.168.8.225 Filename: /joyit_jt-or750i.bin Using: eth1 Load address: 0x80800000 Loading: ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ######################################## ##################### TFTP transfer complete! Bytes transferred: 5636401 (0x560131) Erase FLASH from 0x9F050000 to 0x9F5BFFFF in bank #1 Erasing: ####################################### ####################################### ######### Erased sectors: 87 Copying to FLASH... Writing at address: 0x9F050000 Done! DONE! Firmware upgraded! Hit any key to stop booting: 0 Booting image from 0x9F050000... Image name: MIPS OpenWrt Linux-5.4.143 Build date: 2021-08-31 22:20:08 UTC Architecture: MIPS OS/image type: Linux Kernel Compression: LZMA Data size: 2 MB (2047261 bytes) Load address: 0x80060000 Entry point: 0x80060000 Header CRC... OK! Data CRC... skipped Stopping network... OK! Uncompressing Kernel... OK! Starting kernel...


[ 0.000000] Linux version 5.4.143 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)) #0 Tue Aug 31 22:20:08 2021 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is Joy-IT JT-OR750i [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 122188K/131072K available (5250K kernel code, 193K rwdata, 688K rodata, 1220K init, 205K bss, 8884K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] random: get_random_bytes called from 0x8065fa28 with crng_init=0 [ 0.000000] CPU clock: 550.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns [ 0.000011] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns [ 0.008927] Calibrating delay loop... 364.54 BogoMIPS (lpj=729088) [ 0.047897] pid_max: default: 32768 minimum: 301 [ 0.053370] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.061691] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.076559] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.087705] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.095628] pinctrl core: initialized pinctrl subsystem [ 0.105353] NET: Registered protocol family 16 [ 0.145075] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.161617] clocksource: Switched to clocksource MIPS [ 0.168833] thermal_sys: Registered thermal governor 'step_wise' [ 0.169362] NET: Registered protocol family 2 [ 0.181489] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.190831] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.200469] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.209210] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.217247] TCP: Hash tables configured (established 1024 bind 1024) [ 0.224704] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.232232] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.240676] NET: Registered protocol family 1 [ 0.245732] PCI: CLS 0 bytes, default 32 [ 0.255965] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.273143] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.279859] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.310778] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.324893] pinctrl-single 1804002c.pinmux: 576 pins, size 72 [ 0.332912] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.343500] printk: console [ttyS0] disabled [ 0.348528] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.358369] printk: console [ttyS0] enabled [ 0.358369] printk: console [ttyS0] enabled [ 0.367437] printk: bootconsole [early0] disabled [ 0.367437] printk: bootconsole [early0] disabled [ 0.392512] spi-nor spi0.0: mx25l12805d (16384 Kbytes) [ 0.398002] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.404585] Creating 4 MTD partitions on "spi0.0": [ 0.409584] 0x000000000000-0x000000040000 : "u-boot" [ 0.416188] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.423112] 0x000000050000-0x000000ff0000 : "firmware" [ 0.433846] 2 uimage-fw partitions found on MTD device firmware [ 0.440037] Creating 2 MTD partitions on "firmware": [ 0.445199] 0x000000000000-0x000000200000 : "kernel" [ 0.451697] 0x000000200000-0x000000fa0000 : "rootfs" [ 0.458323] mtd: device 4 (rootfs) set to be root filesystem [ 0.466868] 1 squashfs-split partitions found on MTD device rootfs [ 0.473359] 0x000000560000-0x000000fa0000 : "rootfs_data" [ 0.480364] 0x000000ff0000-0x000001000000 : "art" [ 0.489441] libphy: Fixed MDIO Bus: probed [ 0.834729] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.181604] random: fast init done [ 1.474109] libphy: ag71xx_mdio: probed [ 1.479822] libphy: ar8xxx-mdio: probed [ 1.494491] switch0: Atheros AR8229 rev. 1 switch registered on mdio.0 [ 1.542016] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.552268] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 1.559162] i2c /dev entries driver [ 1.566229] NET: Registered protocol family 10 [ 1.578758] Segment Routing with IPv6 [ 1.582811] NET: Registered protocol family 17 [ 1.587554] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.600982] 8021q: 802.1Q VLAN Support v1.8 [ 1.606759] PCI host bridge /ahb/pcie-controller@180c0000 ranges: [ 1.613194] MEM 0x0000000010000000..0x0000000013ffffff [ 1.618610] IO 0x0000000000000000..0x0000000000000000 [ 1.624311] PCI host bridge to bus 0000:00 [ 1.628628] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 1.635749] pci_bus 0000:00: root bus resource [io 0x0000] [ 1.641517] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.648538] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.656781] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000 [ 1.663070] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 1.670152] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.677173] pci 0000:00:00.0: supports D1 [ 1.681338] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.688581] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.695513] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 1.703110] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 2.027806] ag71xx 19000000.eth: connected to PHY at mdio.0:1f:04 [uid=004dd042, driver=Generic PHY] [ 2.038652] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 2.046289] hctosys: unable to open rtc device (rtc0) [ 2.058003] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.075774] Freeing unused kernel memory: 1220K [ 2.080493] This architecture does not have kernel memory protection. [ 2.087155] Run /sbin/init as init process [ 2.718004] init: Console is alive [ 2.722017] init: - watchdog - [ 3.835657] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.874412] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.892639] init: - preinit - [ 5.580392] random: jshn: uninitialized urandom read (4 bytes read) [ 5.948142] random: jshn: uninitialized urandom read (4 bytes read) [ 6.117410] random: jshn: uninitialized urandom read (4 bytes read) [ 6.859417] eth0: link up (1000Mbps/Full duplex) [ 6.869771] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.882263] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 6.939497] urandom_read: 4 callbacks suppressed [ 6.939509] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 11.169416] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 11.182409] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.299106] eth0: link down [ 11.332708] procd: - early - [ 11.335988] procd: - watchdog - [ 11.953742] procd: - watchdog - [ 11.978378] procd: - ubus - [ 12.067437] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.077420] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.093030] procd: - init - Please press Enter to activate this console. [ 13.328768] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.386436] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff [ 13.394383] Backport generated by backports.git v5.10.42-1-0-gbee5c545 [ 13.482757] xt_time: kernel timezone is -0000 [ 13.830233] PPP generic driver version 2.4.2 [ 13.843213] NET: Registered protocol family 24 [ 13.970078] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x50. [ 13.991186] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002) [ 14.000017] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 14.049315] urngd: v1.0.2 started. [ 14.523873] random: crng init done [ 19.573982] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000 [ 19.583601] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 19.598174] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-87-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 61a92df5 [ 20.174049] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d [ 21.230554] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 21.244504] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410' [ 21.251155] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 21.259487] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 25560 iram: 24780' [ 21.292423] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 21.302786] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 21.633774] ieee80211 phy1: Atheros AR9531 Rev:2 mem=0xb8100000, irq=13 [ 21.646284] kmodloader: done loading kernel modules from /etc/modules.d/* [ 56.242359] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 56.265754] jffs2_build_filesystem(): unlocking the mtd device... [ 56.265765] done. [ 56.274179] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 57.616688] eth0: link up (1000Mbps/Full duplex) [ 57.644724] br-lan: port 1(eth0.1) entered blocking state [ 57.650421] br-lan: port 1(eth0.1) entered disabled state [ 57.656580] device eth0.1 entered promiscuous mode [ 57.661627] device eth0 entered promiscuous mode [ 57.685531] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 57.746376] br-lan: port 1(eth0.1) entered blocking state [ 57.752024] br-lan: port 1(eth0.1) entered forwarding state [ 58.612070] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 102.601362] done. [ 102.603443] jffs2: notice: (2248) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 102.881709] overlayfs: upper fs does not support tmpfile.


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/09/08 22:40
  • by sam0815