Show pagesourceOld revisionsBacklinksBack to top × Table of Contents ipTIME A3004T Supported Versions Hardware Highlights Installation Recovery method Flash Layout OEM easy installation OEM installation using the TFTP recovery method Upgrading OpenWrt LuCI Web Upgrade Process Terminal Upgrade Process Debricking Failsafe mode Basic configuration Specific Configuration Network interfaces Switch Ports (for VLANs) Buttons Hardware Info Photos Opening the case Serial Bootloader mods Hardware mods Bootlogs OEM bootlog OpenWrt bootlog Notes Tags ipTIME A3004T Under Construction! This page is currently under construction. You can edit the article to help completing it. ipTime A3004T is a WiFi 5 AC1300 wireless router based on the MT7621 platform with USB 3.0 port. It's been discontinued and replaced to A3004TW, A white model with less RAM, Flash (Using SPI-NOR instead of NAND), and without USB port. Note: White device in picture is A3004TW. Which is not compatible with A3004T firmware. Be careful that many sellers are just listed A3004TW as A3004T. Supported Versions BrandModelVersionCurrent ReleaseOEM InfoForum SearchTechnical DataipTIMEA3004T22.03.5http://iptime.com/iptime/?page_id=11&pf=3&page=&pt=535&pd=1A3004TView/Edit data Hardware Highlights ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBA3004TMT7621A880128NAND256MT7615Eb/g/na/n/ac--1x 3.0 Installation ModelVersionCurrent ReleaseFirmware OpenWrt InstallFirmware OpenWrt UpgradeFirmware OEM Stock Nothing found → Install OpenWrt (generic explanation) See below section. Recovery method Flash Layout This device uses NAND. but OEM made stock firmware flash layout like a normal spi-nor layout unlike other models. OpenWRT firmware follows this decision. Layer0 raw flash, 131072 KiB Layer1 mtd0 u-boot 512 KiB mtd1 config (u-boot-env) 64 KiB mtd2 factory 64 KiB mtd3 firmware 130752 KiB Layer2 mtd4 kernel about 4 MiB mtd5 ubi Note: Stock OEM firmware has dual-boot functionality. as divide firmware partition. Above layout is OpenWRT firmware. OEM easy installation Note that sometime this will be failed. if failed, use below method. (using recovery) 1. Flash initramfs image via OEM GUI method. 2. Perform sysupgrade using sysupgrade image via SSH or LuCI. OEM installation using the TFTP recovery method 1-1. Power up with holding down the reset key until CPU LED stop blinking. 1-2. or Disassemble and Open the router, Get Serial access, holding `F` during bootloader process. 2. Set fixed ip with 192.168.0.2 with subnet mask 255.255.255.0 3. Flash initramfs image via tftp to 192.168.0.1 4. Perform sysupgrade using sysupgrade image via SSH or LuCI. Specific values needed for tftp Bootloader tftp server IPv4 address 192.168.0.1 Firmware tftp image Latest OpenWrt release (NOTE: use initramfs image) TFTP client required IP address 192.168.0.2 TFTP client required subnet mask 255.255.255.0 Upgrading OpenWrt → generic.sysupgrade LuCI Web Upgrade Process Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL Upload image file for sysupgrade to LuCI Wait for reboot Terminal Upgrade Process If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading: sysupgrade Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. sysupgrade Login as root via SSH on 192.168.1.1, then enter the following commands: cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc Debricking → generic.debrick Try with OEM installation using the TFTP recovery method but using OEM firmware. Failsafe mode → failsafe_and_factory_reset Try with OEM installation using the TFTP recovery method but using OEM firmware or initramfs image. Basic configuration → Basic configuration After flashing, proceed with this. Set up your Internet connection, configure wireless, configure USB port, etc. Specific Configuration Network interfaces The default network configuration is: Interface Name Description Default configuration br-lan LAN & WiFi 192.168.1.1/24 wl0 WiFi Disabled Switch Ports (for VLANs) Port Switch port Internet (WAN) 0 LAN 1 4 LAN 2 3 LAN 3 2 LAN 4 1 Buttons → hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto. The ipTIME A3004T has the following buttons: BUTTON Event Reset reset Hardware Info General Brand ipTIME Model A3004T Versions Device Type WiFi Router Availability Available 2021 Comments - general OpenWrt Support Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=2dde2416e1a2f7a3208095e29c20132ed9910889 Supported Since Release 22.03.0 Supported Current Release 22.03.5 Unsupported Hardware Bootloader U-Boot Target ramips System-On-Chip MT7621A CPU MHz 880 Flash MB 128NAND RAM MB 256 Network Ethernet 100M ports - Ethernet 1Gbit ports Switch ¿ Modem - VLAN ¿ Comments - network ports Wireless WLAN 2.4GHz b/g/n WLAN 5.0GHz a/n/ac WLAN Hardware MT7615E Detachable Antennas - Comments - WLAN radio0 will not work with 5GHz, use radio1 instead. Interfaces USB ports 1x 3.0 SATA ports - Serial Yes JTAG No Comments - USB & SATA ports Misc LED count ¿ Button count ¿ Power supply 12 VDC, 2.0 A Links Forum Topic URL WikiDevi URL OEM device homepage URL http://iptime.com/iptime/?page_id=11&pf=3&page=&pt=535&pd=1 Firmware OEM Stock URL http://iptime.com/iptime/?page_id=126&pageid=1&mod=list&x=0&y=0&keyword=A3004T Firmware OpenWrt Install URL https://downloads.openwrt.org/releases/22.03.5/targets/ramips/mt7621/openwrt-22.03.5-ramips-mt7621-iptime_a3004t-initramfs-kernel.bin Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/releases/22.03.5/targets/ramips/mt7621/openwrt-22.03.5-ramips-mt7621-iptime_a3004t-squashfs-sysupgrade.bin Edit the underlying data View/Edit data Photos Front: Insert photo of front of the casing Back: Insert photo of back of the casing Backside label: Insert photo of backside label Opening the case Note: This will void your warranty! Remove rubber, all screw hidden with rubber. unscrew all screw, and use fryer, start from corner edge. Main PCB: Insert photo of PCB Serial → port.serial general information about the serial port, serial port cable, etc. How to connect to the Serial Port of this specific device: Insert photo of PCB with markings for serial port Serial connection parameters for ipTIME A3004T 57600, 8N1 Bootloader mods → bootloader Hardware mods None so far. Bootlogs OEM bootlog =================================================================== MT7621 stage1 code Mar 12 2015 14:42:52 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xd, 1/0 = 593/431 35000000 PLL2 FB_DL: 0x16, 1/0 = 754/270 59000000 PLL4 FB_DL: 0x17, 1/0 = 611/413 5D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DRAMC_DQSCTL1[0e0]=13000000 DRAMC_DQSGCTL[124]=80000033 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 opt_dle value:10 DRAMC_DDR2CTL[07c]=C287222D DRAMC_PADCTL4[0e4]=000022B3 DRAMC_DQIDLY1[210]=0C0B0A0C DRAMC_DQIDLY2[214]=070A080A DRAMC_DQIDLY3[218]=09090706 DRAMC_DQIDLY4[21c]=09080A09 DRAMC_R0DELDLY[018]=00001E1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 9 10 10 9 7 9 7 5 7 10 | 9 9 9 10 8 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~59)30 8 (1~58)29 1 (1~60)30 9 (1~60)30 2 (1~60)30 10 (1~60)30 3 (1~58)29 11 (2~59)30 4 (1~59)30 12 (1~59)30 5 (1~60)30 13 (1~60)30 6 (1~60)30 14 (1~60)30 7 (1~62)31 15 (1~60)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 10 11 12 10 8 10 7 6 7 10 | 9 9 9 10 8 9 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0082 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0080 DQ loop=13, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(8,8) DRAMC_DQODLY1[200]=88888888 DRAMC_DQODLY2[204]=88888888 20,data:89 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== (Dec 17 2019 - 11:33:36) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ff94000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 8ffc8af0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Dec 17 2019 Time:11:33:36 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN WLLLL Disable WAN port.... cur reg0 = 00001040 new reg0 = 00001840 Please choose the operation: (t:tftp server/b(boot now)/f(flash test)/u(upgrade boot)) default: b 1 0 MAC : 90:**:**:**:**:1c Alias : a3004t 3: System Boot system code via Flash. ## Booting image at bc140000 ... Image Name: a3004t Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 18176328 Bytes = 17.3 MB Load Address: 81001000 Entry Point: 81682e00 ...................................................................................................................................................................................................................................................................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 81682e00) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 [ 0.000000] Linux version 3.10.108 (scchoi@localhost) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #28 SMP Thu Jun 24 11:56:27 KST 2021 [ 0.000000] [ 0.000000] The CPU feqenuce set to 880 MHz [ 0.000000] GCMP present [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00000000-0x00ffffff] [ 0.000000] Normal [mem 0x01000000-0x0fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x0fffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81b92000 s6336 r8192 d14144 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00010073 [ 0.000000] Readback ErrCtl register=00010073 [ 0.000000] Memory: 249976k/262144k available (6704k kernel code, 12168k reserved, 2402k data, 232k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.116000] Calibrating delay loop... 574.46 BogoMIPS (lpj=1148928) [ 0.148000] pid_max: default: 32768 minimum: 301 [ 0.152000] Mount-cache hash table entries: 512 [ 0.156000] launch: starting cpu1 [ 0.160000] launch: cpu1 gone! [ 0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.160000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.192000] Synchronize counters for CPU 1: done. [ 0.196000] launch: starting cpu2 [ 0.200000] launch: cpu2 gone! [ 0.200000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.200000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.200000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.200000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.232000] Synchronize counters for CPU 2: done. [ 0.236000] launch: starting cpu3 [ 0.240000] launch: cpu3 gone! [ 0.240000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.240000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.240000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.240000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.268000] Synchronize counters for CPU 3: done. [ 0.272000] Brought up 4 CPUs [ 0.276000] devtmpfs: initialized [ 0.280000] NET: Registered protocol family 16 [ 0.576000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.580000] PCIE PHY initialize [ 0.584000] ***** Xtal 40MHz ***** [ 0.588000] start MT7621 PCIe register access [ 1.180000] RALINK_RSTCTRL = 7000000 [ 1.184000] RALINK_CLKCFG1 = 77ffeff8 [ 1.188000] [ 1.188000] *************** MT7621 PCIe RC mode ************* [ 1.680000] PCIE1 no card, disable it(RST&CLK) [ 1.684000] PCIE2 no card, disable it(RST&CLK) [ 1.688000] pcie_link status = 0x1 [ 1.692000] RALINK_RSTCTRL= 1000000 [ 1.696000] *** Configure Device number setting of Virtual PCI-PCI bridge *** [ 1.700000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 [ 1.704000] PCIE0 enabled [ 1.708000] interrupt enable status: 100000 [ 1.712000] Port 0 N_FTS = 1b105000 [ 1.716000] config reg done [ 1.720000] init_rt2880pci done [ 1.736000] bio: create slab <bio-0> at 0 [ 1.740000] vgaarb: loaded [ 1.744000] SCSI subsystem initialized [ 1.748000] usbcore: registered new interface driver usbfs [ 1.752000] usbcore: registered new interface driver hub [ 1.756000] usbcore: registered new device driver usb [ 1.760000] PCI host bridge to bus 0000:00 [ 1.764000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.768000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.772000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.776000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.780000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.784000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff] [ 1.788000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 1.792000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.796000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.800000] BAR0 at slot 0 = 0 [ 1.804000] bus=0x0, slot = 0x0 [ 1.808000] res[0]->start = 0 [ 1.812000] res[0]->end = 0 [ 1.816000] res[1]->start = 60100000 [ 1.820000] res[1]->end = 6010ffff [ 1.824000] res[2]->start = 0 [ 1.828000] res[2]->end = 0 [ 1.832000] res[3]->start = 0 [ 1.836000] res[3]->end = 0 [ 1.840000] res[4]->start = 0 [ 1.844000] res[4]->end = 0 [ 1.848000] res[5]->start = 0 [ 1.852000] res[5]->end = 0 [ 1.856000] bus=0x1, slot = 0x0, irq=0x4 [ 1.860000] res[0]->start = 60000000 [ 1.864000] res[0]->end = 600fffff [ 1.868000] res[1]->start = 0 [ 1.872000] res[1]->end = 0 [ 1.876000] res[2]->start = 0 [ 1.880000] res[2]->end = 0 [ 1.884000] res[3]->start = 0 [ 1.888000] res[3]->end = 0 [ 1.892000] res[4]->start = 0 [ 1.896000] res[4]->end = 0 [ 1.900000] res[5]->start = 0 [ 1.904000] res[5]->end = 0 [ 1.908000] Switching to clocksource Ralink Systick timer [ 1.912000] NET: Registered protocol family 2 [ 1.916000] Clockevents: could not switch to one-shot mode: [ 1.916000] MIPS is not functional. [ 1.916000] Clockevents: could not switch to one-shot mode: [ 1.916000] MIPS is not functional. [ 1.916000] Could not switch to high resolution mode on CPU 1 [ 1.916000] Clockevents: could not switch to one-shot mode: MIPS is not functional. [ 1.916000] Could not switch to high resolution mode on CPU 0 [ 1.916000] Could not switch to high resolution mode on CPU 3 [ 2.004000] Clockevents: could not switch to one-shot mode: MIPS is not functional. [ 2.020000] Could not switch to high resolution mode on CPU 2 [ 2.032000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.048000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.060000] TCP: Hash tables configured (established 2048 bind 2048) [ 2.072000] TCP: reno registered [ 2.080000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.092000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.104000] NET: Registered protocol family 1 [ 2.116000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.128000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.148000] fuse init (API version 7.22) [ 2.156000] msgmni has been set to 488 [ 2.164000] io scheduler noop registered (default) [ 2.172000] reg_int_mask=0, INT_MASK= 0 [ 2.180000] HSDMA_init [ 2.184000] [ 2.184000] hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 [ 2.204000] [ 2.204000] hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 [ 2.220000] TX_CTX_IDX0 = 0 [ 2.224000] TX_DTX_IDX0 = 0 [ 2.232000] RX_CRX_IDX0 = 3ff [ 2.236000] RX_DRX_IDX0 = 0 [ 2.240000] set_fe_HSDMA_glo_cfg [ 2.248000] HSDMA_GLO_CFG = 465 [ 2.256000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.268000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A [ 2.284000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A [ 2.296000] Ralink gpio driver initialized [ 2.304000] spidrv_major = 217 [ 2.316000] brd: module loaded [ 2.324000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 2.336000] Allocate 16 byte aligned buffer: 8196e190 [ 2.348000] Enable NFI Clock [ 2.352000] # MTK NAND # : Use HW ECC [ 2.360000] NAND ID [C2 F1 80 95 02, 00809502] [ 2.368000] Device found in MTK table, ID: c2f1, EXT_ID: 809502 [ 2.380000] Support this Device in MTK table! c2f1 [ 2.388000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 2.412000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 2.428000] Scanning device for bad blocks [ 2.676000] Signature matched and data read! [ 2.684000] load_fact_bbt success 1023 [ 2.692000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.712000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.732000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.748000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.768000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.788000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.808000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.828000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.848000] Creating 6 MTD partitions on "MT7621-NAND": [ 2.860000] 0x000000000000-0x000007f80000 : "ALL" [ 2.896000] 0x000000000000-0x000000080000 : "Bootloader" [ 2.908000] 0x000000080000-0x0000000a0000 : "Config" [ 2.920000] 0x0000000a0000-0x0000000c0000 : "Factory" [ 2.928000] 0x000000140000-0x000007f80000 : "firmware" [ 2.972000] 0x0000004b0000-0x000007f80000 : "rootfs" [ 2.980000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 3.036000] PART->MTD.SIZE : 128778240 270658437120 4915200 [ 3.044000] mtd: partition "rootfs_data" created automatically, ofs=0x4800000, len=0x3780000 [ 3.064000] 0x000004800000-0x000007f80000 : "rootfs_data" [ 3.084000] 0x0000024a0000-0x000004800000 : "firmware2" [ 3.104000] [mtk_nand] probe successfully! [ 3.112000] rootfs = 4b0000 to 4800000 [ 3.120000] PPP generic driver version 2.4.2 [ 3.128000] PPP BSD Compression module registered [ 3.140000] PPP Deflate Compression module registered [ 3.148000] PPP MPPE Compression module registered [ 3.156000] NET: Registered protocol family 24 [ 3.168000] PPTP driver version 0.8.5 [ 3.172000] register mt_drv [ 3.200000] [ 3.200000] == pAd = c0201000, size = 7672704, Status=0 == [ 3.212000] pAd->PciHif.CSRBaseAddress =0xc0100000, csr_addr=0xc0100000! [ 3.228000] RTMPInitPCIeDevice():device_id=0x7615 [ 3.236000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 [ 3.252000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 [ 3.260000] AP Driver version-5.0.4.0 [ 3.268000] RtmpChipOpsHook(223): Not support for HIF_MT yet! MACVersion=0x0 [ 3.280000] mt7615_init()--> [ 3.288000] Use the default ePAeLNA bin image! [ 3.296000] Use the default /etc_ro/wlan/MT7615E_EEPROM1.bin bin image! [ 3.308000] <--mt7615_init() [ 3.320000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 3.328000] RtmpOSFileOpen(): Error 2 opening /etc/wireless/l1profile.dat [ 3.344000] rdm_major = 253 [ 3.348000] GMAC1_MAC_ADRH -- : 0x0000000c [ 3.356000] GMAC1_MAC_ADRL -- : 0x432880c1 [ 3.364000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! [ 3.384000] GMAC1_MAC_ADRH -- : 0x0000000c [ 3.392000] GMAC1_MAC_ADRL -- : 0x432880e0 [ 3.400000] PROC INIT OK! [ 3.408000] usbcore: registered new interface driver cdc_ether [ 3.420000] usbcore: registered new interface driver cdc_eem [ 3.428000] usbcore: registered new interface driver rndis_host [ 3.440000] usbcore: registered new interface driver cdc_subset [ 3.452000] usbcore: registered new interface driver ipheth [ 3.464000] usbcore: registered new interface driver usblp [ 3.476000] usbcore: registered new interface driver usb-storage [ 3.488000] Netfilter messages via NETLINK v0.30. [ 3.496000] nf_conntrack version 0.5.0 (3905 buckets, 15620 max) [ 3.508000] ipip: IPv4 over IPv4 tunneling driver [ 3.520000] gre: GRE over IPv4 demultiplexor driver [ 3.528000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.540000] Type=Linux [ 3.544000] TCP: cubic registered [ 3.552000] Twin IP Module Init [ 3.556000] --> Init Smart QoS Monitor [ 3.564000] Initializing XFRM netlink socket [ 3.572000] NET: Registered protocol family 17 [ 3.580000] NET: Registered protocol family 15 [ 3.592000] Ebtables v2.0 registered [ 3.596000] l2tp_core: L2TP core driver, V2.0 [ 3.608000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 3.616000] 8021q: 802.1Q VLAN Support v1.8 [ 3.632000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 3.648000] devtmpfs: mounted [ 3.656000] Freeing unused kernel memory: 232K ---> Mount devtmpfs [ Failed ] Checking Uboot Env ---> [ OK : a3004t ] sys_initfs:Check EEPROM (wl_mode:0) -> [ OK ] sys_initfs:Check EEPROM (wl_mode:1) -> [ OK ] Checking System Requirements ******************************************* DRAM SIZE : Requirement->256 Mbytes / Mounted->256 Mbytes -----------> [OK] FLASH SIZE : Requirement->128 Mbytes / Mounted->128 Mbytes -----------> [OK] Start inittime Product ID:a3004t Version:14.108 ---> init_sys Install Module Failed: nf_conntrack_ftp.ko Install Module Failed: nf_nat_ftp.ko ---> gpio_board_init ---> gpio.init end ---> pre_init ---> Load sysctl.d ---> init_restore mount jffs2: I/O error mounting /dev/mtdblock6 to /data with jffs2 failed JFFS2 mount Failed.Initialize FS Unlocking rootfs_data ... Writing from <stdin> to rootfs_data ... [ ][e][w] JFFS2 mount(/data) Success --> Restoring Config... 1st Config -Default -- mgmt access - credential patched -- patched (login --> removed) -- patched (password --> removed) --> restore_http_session ---> init_timezone ---> init_logsystem ---> init_usb ---> init_macaddr ================================================================= press magic key to change default setting ... LAN MAC : 90:**:**:**:**:1F WAN MAC : 90:**:**:**:**:1D ---> init_wireless --> Bridge multicast snooping : 1 --> Bridge multicast querier :0 ---> wl.preinit --->Pre-Interface up/down:ra0 Scanning best channel for wl_mode:0 --->[ 3 ] --> set_profile WL_MODE:1 Profile:/etc/wireless/mt7615/mt7615.1.5G.dat Default Profile:/default/etc/wireless/mt7615/mt7615.1.5G.dat --> set_profile WL_MODE:0 Profile:/etc/wireless/mt7615/mt7615.1.2G.dat Default Profile:/default/etc/wireless/mt7615/mt7615.1.2G.dat MTK TPC FOR 5g : tpc_duty=100:060:030:010 MTK TPC FOR 5g : tpc=1:1:1:120:114:124:0060:1 MTK TPC FOR 2g : tpc_duty=100:060:030:010 MTK TPC FOR 2g : tpc=1:1:1:120:114:124:0060:1 ---> init_diag ---> init_iptables_pre ---> init_network ---> init_iptables_post --->init_qos killall: dhcpd.helper: no process killed ---> init_apps ---> init_connctrl ---> init_iptv_config ---> init_ethernet_switch ---> wan port down --->mt75xx_init_eswitch (pub_iptv_devport:-1) ---> wan port up -->init_jumbo_frame ---> init_portconfig ---> wired lan ports down & up. Optimize CPU : wireless End inittime killall: httpd: no process killed killall: dhcpd: no process killed killall: bcrelay: no process killed killall: apcpd: no process killed killall: gpioctld: no process killed Stop MTK 8021x Daemon for rax0. Stop MTK 8021x Daemon for ra0. [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network killall: pptpd: no process killed killall: xl2tpd: no process killed Stopping strongSwan IPsec failed: starter is not running Check DHCP PID Elapsed Time: 1 nas_signal_service => cupsd killall: cupsd: no process killed umount: can't unmount /tmp/var/spool/cups: Invalid argument [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network killall: pptpd: no process killed Session Garbage Collecting:Maybe system time is updated.( 106 0 ) Update Session timestamp and try it after 5 seconds again. killall: igmpproxy: no process killed igmpproxy, Version 0.1 beta2, Build 200623 Copyright 2005 by Johnny Egeland <johnny@rlo.org> Distributed under the GNU GENERAL PUBLIC LICENSE, Version 2 - check GPL.txt [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network ---> LED Silent Control --> Set LED -> On killall: url_redirect: no process killed killall: snmpd: no process killed killall: snmptrapd: no process killed 1221 No USB Printer by lpinfo no nas_signal : nas_callback fuse_callback -----> No Fuse fs. Stop callback killall: pptpd: no process killed Warn: select() failure; Errno(4): Interrupted system call igmpproxy, Version 0.1 beta2, Build 200623 Copyright 2005 by Johnny Egeland <johnny@rlo.org> Distributed under the GNU GENERAL PUBLIC LICENSE, Version 2 - check GPL.txt 1221 No USB Printer by lpinfo header read: Connection reset by peer 1221 No USB Printer by lpinfo 1221 No USB Printer by lpinfo 1221 No USB Printer by lpinfo [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network 1221 Timeout for Printer Recognization [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network [DHCPC:Check IP] : Check WAN IP : interface: eth3 192.168.0.17, 255.255.255.0 [DHCPC:Check IP] : Same network Not found downgradable version. Allow all version killall: snmpd: no process killed killall: upnpd: no process killed killall: timed: no process killed Warn: select() failure; Errno(4): Interrupted system call killall: smbd: no process killed killall: nmbd: no process killed killall: lighttpd: no process killed killall: lighttpd_ipdisk: no process killed killall: proftpd: no process killed killall: rsync: no process killed killall: iptimecloud: no process killed killall: pppd: no process killed SYSD Off killall: transmission-daemon: no process killed killall: minidlna: no process killed killall: nmbd: no process killed killall: smbd: no process killed killall: lighttpd_ipdisk: no process killed killall: proftpd: no process killed killall: lighttpd: no process killed killall: rsync: no process killed killall: transmission-daemon: no process killed killall: minidlna: no process killed killall: smbd: no process killed /usr/bin/killall smbd killall: proftpd: no process killed /usr/bin/killall proftpd killall: lighttpd: no process killed /usr/bin/killall lighttpd killall: rsync: no process killed /usr/bin/killall rsync killall: iptimecloud: no process killed /usr/bin/killall iptimecloud killall: transmission-daemon: no process killed /usr/bin/killall transmission-daemon killall: minidlna: no process killed /usr/bin/killall minidlna --> Stop exfat all for :all killall: mount.exfat-fuse: no process killed killall: igmpproxy: no process killed --> updaemon: Waiting Flash Write command --> updaemon: Waiting Flash Write command --> updaemon: Waiting Flash Write command --> updaemon: Waiting Flash Write command --> updaemon: Updating firmware --> updaemon: Finish reboot_system: reason : normal --> Shutdown services killall: igmpproxy: no process killed killall: nmbd: no process killed killall: smbd: no process killed killall: lighttpd_ipdisk: no process killed killall: proftpd: no process killed killall: lighttpd: no process killed killall: rsync: no process killed killall: transmission-daemon: no process killed killall: minidlna: no process killed killall: smbd: no process killed /usr/bin/killall smbd killall: proftpd: no process killed /usr/bin/killall proftpd killall: lighttpd: no process killed /usr/bin/killall lighttpd killall: rsync: no process killed /usr/bin/killall rsync killall: iptimecloud: no process killed /usr/bin/killall iptimecloud killall: transmission-daemon: no process killed /usr/bin/killall transmission-daemon killall: minidlna: no process killed /usr/bin/killall minidlna --> Stop exfat all for :all killall: mount.exfat-fuse: no process killed --> All wireless interface down --> Stop configuration store system --> sys.reset --> REBOOT [ 159.056000] Restarting system. OpenWrt bootlog COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING Notes Space for additional notes, links to forum threads or other resources. ... Tags Add tags below, then remove this fixme. How to add tags EXAMPLETAG This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies EXAMPLETAG Last modified: 2023/07/23 13:13by kimwonj77