Inteno EG400

Inteno EG400 comes with OpenWrt (Inteno Iopsys) from vendor, although their own build of it.

Ver CPU Ram Flash Network Wireless USB Serial JTag
v1.0 Broadcom 963138 512MiB 256MiB 1 WAN (Gbit) + 4x LAN (GBit) + 2x VoIP 802.11ac 4×4 Yes 1x 3.0 + 1x 2.0 Yes! ?

Manufacturer's announcement: https://www.intenogroup.com/wp-content/uploads/2017/10/Inteno-press-release_EG400.pdf

Forum: https://forum.openwrt.org/t/iopsys-eg400-possible-to-run-up-to-date-openwrt/20673

Instruction set ARMv7
Vendor Broadcom
bootloader CFE
System-On-Chip Broadcom BCM963138
CPU @Frq 1000 MHz
Flash size 256 MiB
RAM size 512 MiB
Wireless No1 Broadcom BCM43142 802.11b/g/n (mPCIE)
Wireless No2 ?
mPCIE Yes. 3 slots
USB Yes 1 x 3.0 + 1 x 2.0
PSU 12V DC 2A 24W Sunny Computer Technology Co.LTD Model: SYS1428-2412-W2E
Serial Yes
JTAG ?

HELO CPU0 PMCM PMCS PMCD CODE L1CD MMUI ZBBS MAIN 4.1605-1.0.38-118.3-INT1.5 DRAM NVRAM memcfg 0x10427 MCB chksum 0xf52f553a DDR3-1600 CL11 %dMB High Temperature SRT Changed Byte Lane LDE Changed Byte Lane LDE PASS NAES LZND LZOK

Base: 4.16_05 CFE version 1.0.38-118.3-INT1.5 for BCM963138 (32bit,SP,LE) Build Date: Tue Jan 14 16:22:02 CET 2020 (inteno@bs1) Copyright (C) 2000-2015 Broadcom Corporation.

Boot Strap Register: 0x7dfffc2f Chip ID: BCM63139B0, ARM Cortex A9 Dual Core: 1000MHz Total Memory: 536870912 bytes (512MB) NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes NAND flash device: , id 0xc2da block 128KB size 262144KB getInMemNvramData: valid=1 sector=1 seqNum=3 iVersion=4 pmc_init:PMC using DQM mode isUbiFlashLayout: is_ubi=1 getRootFSPartStartEndBlock: ix=0, start_blk=4, end_blk=44 getTagFromPartition: imageNumber=1 seq=001 getRootFSPartStartEndBlock: ix=1, start_blk=44, end_blk=84 getTagFromPartition: imageNumber=2 seq=002 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host/tftp (f/h/c) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Default host ramdisk file name : Default ramdisk store address : Board Id (0-0) : EG400R0 Number of MAC Addresses (1-32) : 16 Base MAC Address : 44:d4:37:44:30:bc PSI Size (1-128) KBytes : 48 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 DSL Annex [A|B|X] : X MC memory allocation (MB) : 4 TM memory allocation (MB) : 20 DHD 0 memory allocation (MB) : 0 DHD 1 memory allocation (MB) : 0 DHD 2 memory allocation (MB) : 0 WLan Feature : 0x00 Voice Board Configuration (0-2) : Si32260_LCQC

* Press any key to stop auto run (1 seconds) * Auto run second count down: 110 Booting from latest image (address 0x00580000, flash offset 0x00580000) … Decompression LZMA Image OK! Entry at 0x00008000 Starting program at 0x00008000 [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.11-rt19 (inteno@bs1) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Tue Jan 14 16:14:35 CET 2020 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: BCM963138 [ 0.000000] Ignoring unrecognised tag 0x41000603 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Initialized persistent memory from 0e380000-0e3fffff [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0fd00000 to virtual address at 0xcfd00000 with size of 0x300000 byte for DSL [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0e800000 to virtual address at 0xce800000 with size of 0x1400000 byte for RDPA tm [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0e400000 to virtual address at 0xce400000 with size of 0x400000 byte for RDPA mc [ 0.000000] On node 0 totalpages: 124160 [ 0.000000] free_area_init_node: node 0, pgdat c05d6020, node_mem_map c1000000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 992 pages used for memmap [ 0.000000] Normal zone: 119072 pages, LIFO batch:31 [ 0.000000] pmc_init:PMC using DQM mode [ 0.000000] pmc_init:17d 342034a 4b004b [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x6a450000, Cache size: 524288 B [ 0.000000] PERCPU: Embedded 7 pages/cpu @c1405000 s5696 r8192 d14784 u32768 [ 0.000000] pcpu-alloc: s5696 r8192 d14784 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 123136 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rw noinitrd [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 228MB 1MB 256MB = 485MB total [ 0.000000] Memory: 483796k/483796k available, 40492k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc05651f4 (5493 kB) [ 0.000000] .init : 0xc0566000 - 0xc058c640 ( 154 kB) [ 0.000000] .data : 0xc058e000 - 0xc05d6ba0 ( 291 kB) [ 0.000000] .bss : 0xc05d6bc4 - 0xc068fa30 ( 740 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP. [ 0.000000] NR_IRQS:256 [ 0.000000] Cortex A9 MPCORE GIC init [ 0.000000] DIST at fc01f000, CPU_IF at fc01e100 [ 0.000000] map_hw_timer_interrupt,132: interrupt_id 96 [ 0.000000] map_hw_timer_interrupt,132: interrupt_id 97 [ 0.000000] map_hw_timer_interrupt,132: interrupt_id 98 [ 0.000000] map_hw_timer_interrupt,132: interrupt_id 99 [ 0.000000] sched_clock: 32 bits at 1kHz, resolution 1000000ns, wraps every 4294967295ms [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.002000] Calibrating delay loop… 1990.65 BogoMIPS (lpj=995328) [ 0.011000] pid_max: default: 32768 minimum: 301 [ 0.012000] Mount-cache hash table entries: 512 [ 0.013000] –Kernel Config– [ 0.014000] SMP=1 [ 0.015000] PREEMPT=1 [ 0.016000] DEBUG_SPINLOCK=0 [ 0.017000] DEBUG_MUTEXES=0 [ 0.018000] Initializing cgroup subsys memory [ 0.019000] CPU: Testing write buffer coherency: ok [ 0.020000] Broadcom Logger v0.1 Jan 14 2020 16:09:37 [ 0.035000] Setting up static identity map for 0x416c18 - 0x416c4c [ 0.056000] CPU1: Booted secondary processor [ 0.064000] CPU1: Unknown IPI message 0x1 [ 0.064000] Brought up 2 CPUs [ 0.064000] SMP: Total of 2 processors activated (3981.31 BogoMIPS). [ 0.085000] NET: Registered protocol family 16 [ 0.087000] persistent_ram: uncorrectable error in header [ 0.088000] persistent_ram: no valid data in buffer (sig = 0xffffffff) [ 0.090000] console [ram-1] enabled [ 0.092000] getInMemNvramData: valid=1 sector=1 seqNum=3 iVersion=4 [ 0.117000] bcm63xx_pcie: setting resistor calibration value to 0x9 [ 0.123000] bcm63xx_pcie: applying serdes parameters [ 0.183000] PCIE port 0 SSC Disabled [ 0.710000] PCIE port 0 link-up [ 0.717000] PCIE port 0 SSC Enabled [ 0.719000] PCI host bridge to bus 0000:00 [ 0.720000] pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff] [ 0.721000] pci 0000:00:00.0: [14e4:6313] type 01 class 0x060400 [ 0.722000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.723000] PCI: bus0: Fast back to back transfers disabled [ 0.724000] pci 0000:01:00.0: [14e4:a8db] type 00 class 0x028000 [ 0.725000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit] [ 0.726000] pci 0000:01:00.0: supports D1 D2 [ 0.727000] pci 0000:00:00.0: Checking PCIe ASPM for vendor 14e4 device a8db [ 0.730000] PCI: bus1: Fast back to back transfers disabled [ 0.731000] pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x900fffff] [ 0.732000] pci 0000:01:00.0: BAR 0: assigned [mem 0x90000000-0x90007fff 64bit] [ 0.733000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.734000] pci 0000:00:00.0: bridge window [mem 0x90000000-0x900fffff] [ 0.736000] PCI: enabling device 0000:00:00.0 (0140 → 0143) [ 0.760000] bcm63xx_pcie: setting resistor calibration value to 0x9 [ 0.766000] bcm63xx_pcie: applying serdes parameters [ 0.827000] PCIE port 1 SSC Disabled [ 1.354000] PCIE port 1 link-up [ 1.361000] PCIE port 1 SSC Enabled [ 1.362000] PCI host bridge to bus 0001:00 [ 1.363000] pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff] [ 1.364000] pci 0001:00:00.0: [14e4:6313] type 01 class 0x060400 [ 1.365000] pci 0001:00:00.0: PME# supported from D0 D3hot [ 1.366000] PCI: bus0: Fast back to back transfers disabled [ 1.367000] pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000 [ 1.368000] pci 0001:01:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit] [ 1.369000] pci 0001:01:00.0: reg 18: [mem 0x00000000-0x007fffff 64bit] [ 1.370000] pci 0001:01:00.0: reg 20: [mem 0x00000000-0x000fffff 64bit pref] [ 1.371000] pci 0001:01:00.0: supports D1 D2 [ 1.372000] pci 0001:00:00.0: Checking PCIe ASPM for vendor 14e4 device 4365 [ 1.373000] pci 0001:00:00.0: Disabling PCIe ASPM for vendor 14e4 device 4365 [ 1.374000] PCI: bus1: Fast back to back transfers disabled [ 1.375000] pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff] [ 1.376000] pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.377000] pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit] [ 1.378000] pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.379000] pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit] [ 1.380000] pci 0001:00:00.0: PCI bridge to [bus 01-01] [ 1.381000] pci 0001:00:00.0: bridge window [mem 0xa0000000-0xa0bfffff] [ 1.382000] pci 0001:00:00.0: bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.383000] PCI: enabling device 0001:00:00.0 (0140 → 0143) [ 1.391000] bio: create slab <bio-0> at 0 [ 1.395000] SCSI subsystem initialized [ 1.399000] usbcore: registered new interface driver usbfs [ 1.404000] usbcore: registered new interface driver hub [ 1.410000] usbcore: registered new device driver usb [ 1.415000] bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated [ 1.423000] skb_free_task created successfully [ 1.427000] gbpm_do_work scheduled [ 1.430000] BLOG v3.0 Initialized [ 1.434000] BLOG Rule v1.0 Initialized [ 1.438000] Broadcom IQoS v0.1 Jan 14 2020 16:14:30 initialized [ 1.444000] Broadcom GBPM v0.1 Jan 14 2020 16:14:30 initialized [ 1.450000] NET: Registered protocol family 8 [ 1.455000] NET: Registered protocol family 20 [ 1.460000] Switching to clocksource timer_cs [ 1.465000] NET: Registered protocol family 2 [ 1.469000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 1.476000] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.484000] TCP bind hash table entries: 16384 (order: 5, 196608 bytes) [ 1.491000] TCP: Hash tables configured (established 16384 bind 16384) [ 1.497000] TCP: reno registered [ 1.500000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.506000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.513000] NET: Registered protocol family 1 [ 1.518000] RPC: Registered named UNIX socket transport module. [ 1.523000] RPC: Registered udp transport module. [ 1.528000] RPC: Registered tcp transport module. [ 1.533000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.541000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.542000] jffs2: version 2.2. (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 1.544000] fuse init (API version 7.18) [ 1.546000] msgmni has been set to 944 [ 1.548000] io scheduler noop registered (default) [ 1.553000] brd: module loaded [ 1.556000] loop: module loaded [ 1.558000] Broadcom NAND controller (BrcmNand Controller) [ 1.559000] mtd→oobsize=0, mtd→eccOobSize=0 [ 1.560000] NAND_CS_NAND_XOR=00000000 [ 1.561000] B4: NandSelect=40000001, nandConfig=26152300, chipSelect=0 [ 1.562000] brcmnand_read_id: CS0: dev_id=c2da9095 [ 1.563000] After: NandSelect=00000001, nandConfig=26152300 [ 1.564000] DevId c2da9095 may not be supported. Will use config info [ 1.565000] Spare Area Size = 16B/512B [ 1.566000] Block size=00020000, erase shift=17 [ 1.567000] NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11 [ 1.568000] busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff [ 1.569000] ECC level changed to 4 [ 1.570000] OOB size changed to 16 [ 1.571000] BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 256MB on CS0 [ 1.572000] [ 1.572000] Found NAND on CS0: ACC=c3840010, cfg=26152300, flashId=c2da9095, tim1=65324458, tim2=80000e54 [ 1.573000] BrcmNAND version = 0x80000700 256MB @00000000 [ 1.574000] brcmnand_scan: B4 nand_select = 00000001 [ 1.575000] brcmnand_scan: After nand_select = 00000001 [ 1.576000] handle_acc_control: default CORR ERR threshold 3 bits [ 1.577000] ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16 [ 1.578000] page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17 [ 1.579000] Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000 [ 1.580000] ECC layout=brcmnand_oob_bch4_2k [ 1.581000] brcmnand_scan: mtd→oobsize=64 [ 1.582000] brcmnand_scan: oobavail=35, eccsize=512, writesize=2048 [ 1.583000] brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7 [ 1.584000] –>brcmnand_default_bbt [ 1.585000] brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr [ 1.586000] Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS0 [ 1.587000] Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS0 [ 1.588000] brcmnand_reset_corr_threshold: default CORR ERR threshold 3 bits for CS0 [ 1.589000] nand_read_bbt: Bad block at 0x04a80000 [ 1.590000] Creating 7 MTD partitions on “brcmnand.0”: [ 1.591000] 0x000000080000-0x000000580000 : “kernel_0” [ 1.592000] 0x000000580000-0x000000a80000 : “kernel_1” [ 1.594000] 0x000000020000-0x000000080000 : “nvram2” [ 1.596000] 0x000000000000-0x000000020000 : “nvram” [ 1.598000] 0x000000a80000-0x00000ff00000 : “ubi” [ 1.600000] 0x000000a80000-0x000007d80000 : “mtd_lo” [ 1.602000] 0x000007d80000-0x00000ff00000 : “mtd_hi” [ 1.604000] UBI: attaching mtd4 to ubi0 [ 1.605000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.606000] UBI: logical eraseblock size: 126976 bytes [ 1.607000] UBI: smallest flash I/O unit: 2048 [ 1.608000] UBI: VID header offset: 2048 (aligned 2048) [ 1.609000] UBI: data offset: 4096 [ 2.531000] UBI: max. sequence number: 6680 [ 2.538000] UBI: attached mtd4 to ubi0 [ 2.539000] UBI: MTD device name: “ubi” [ 2.540000] UBI: MTD device size: 244 MiB [ 2.541000] UBI: number of good PEBs: 1955 [ 2.542000] UBI: number of bad PEBs: 1 [ 2.543000] UBI: number of corrupted PEBs: 0 [ 2.544000] UBI: max. allowed volumes: 128 [ 2.545000] UBI: wear-leveling threshold: 4096 [ 2.546000] UBI: number of internal volumes: 1 [ 2.547000] UBI: number of user volumes: 2 [ 2.548000] UBI: available PEBs: 0 [ 2.549000] UBI: total number of reserved PEBs: 1955 [ 2.550000] UBI: number of PEBs reserved for bad PEB handling: 76 [ 2.551000] UBI: max/mean erase counter: 7/4 [ 2.552000] UBI: image sequence number: 1783426881 [ 2.553000] UBI: background thread “ubi_bgt0d” started, PID 285 [ 2.562000] tun: Universal TUN/TAP device driver, 1.6 [ 2.563000] tun: (C) 1999-2004 Max Krasnyansky maxk&#64;qualcomm.com [ 2.564000] PPP generic driver version 2.4.2 [ 2.565000] PPP BSD Compression module registered [ 2.566000] PPP Deflate Compression module registered [ 2.568000] PPP MPPE Compression module registered [ 2.572000] NET: Registered protocol family 24 [ 2.577000] usbcore: registered new interface driver cdc_acm [ 2.583000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.591000] usbcore: registered new interface driver usbserial [ 2.597000] usbcore: registered new interface driver usbserial_generic [ 2.604000] USB Serial support registered for generic [ 2.609000] usbserial: USB Serial Driver core [ 2.613000] usbcore: registered new interface driver cp210x [ 2.619000] USB Serial support registered for cp210x [ 2.624000] usbcore: registered new interface driver ftdi_sio [ 2.630000] USB Serial support registered for FTDI USB Serial Device [ 2.637000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver [ 2.643000] usbcore: registered new interface driver option [ 2.648000] USB Serial support registered for GSM modem (1-port) [ 2.655000] usbcore: registered new interface driver pl2303 [ 2.660000] USB Serial support registered for pl2303 [ 2.665000] i2c /dev entries driver [ 2.669000] brcmboard: brcm_board_init entry [ 2.673000] SES: Button Interrupt 0x1 is enabled [ 2.731000] DYING GASP IRQ Initialized and Enabled [ 2.736000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm963xx-gpio [ 2.743000] Serial: BCM63XX driver $Revision: 3.00 $ [ 2.748000] Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands) [ 2.758000] ttyS0 at MMIO 0xfffe8600 (irq = 64) is a BCM63XX [ 2.764000] ttyS1 at MMIO 0xfffe8620 (irq = 65) is a BCM63XX [ 2.771000] BPM: tot_mem_size=536870912B (512MB), buf_mem_size <15%> =80530635B (76MB), num of buffers=31068, buf size=2592 [ 2.781000] Broadcom BPM Module Char Driver v0.1 Jan 14 2020 16:10:00 Registered<244> [ 2.950000] GACT probability NOT on [ 2.953000] Mirror/redirect action on [ 2.957000] u32 classifier [ 2.959000] input device check on [ 2.963000] Actions configured [ 2.967000] TCP: cubic registered [ 2.970000] Initializing XFRM netlink socket [ 2.975000] NET: Registered protocol family 10 [ 2.980000] IPv6 over IPv4 tunneling driver [ 2.985000] NET: Registered protocol family 17 [ 2.989000] NET: Registered protocol family 15 [ 2.993000] Initializing MCPD Module [ 2.997000] Ebtables v2.0 registered [ 3.000000] ebt_time registered [ 3.004000] ebt_ftos registered [ 3.007000] ebt_wmm_mark registered [ 3.010000] L2TP core: blog_l2tp_rcv_check [ 3.015000] L2TP core driver, V2.0 [ 3.018000] PPPoL2TP kernel driver, V2.0 [ 3.022000] 8021q: 802.1Q VLAN Support v1.8 [ 3.053000] registered taskstats version 1 [ 3.081000] UBIFS: recovery needed [ 3.211000] UBIFS: recovery completed [ 3.215000] UBIFS: mounted UBI device 0, volume 1, name “rootfs_1” [ 3.221000] UBIFS: file system size: 117706752 bytes (114948 KiB, 112 MiB, 927 LEBs) [ 3.229000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) [ 3.237000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.243000] UBIFS: default compressor: lzma [ 3.247000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 3.253000] VFS: Mounted root (ubifs filesystem) on device 0:10. [ 3.259000] Freeing init memory: 152K [ 3.377000] init: Console is alive [ 4.382000] init: - preinit -

* Boot reason is Power ON *

Setting up brcm environment mount: can't read '/etc/fstab': No such file or directory Copying device files from /lib/dev to /dev cp: target '/dev/shm' is not a directory DSL Annex A default ln: /etc/adsl/adsl_phy.bin: File exists Loading brcm modules Loading drivers and kernel modules…

[ 4.669000] rdpa_gpl_ext: exports duplicate symbol f_rdpa_epon_drv (owned by rdpa_gpl) insmod: can't insert '/lib/modules/3.4.11-rt19/extra/rdpa_gpl_ext.ko': invalid module format [ 4.818000] rdpa: module license 'Proprietary' taints kernel. [ 4.819000] Disabling lock debugging due to kernel taint [ 4.855000] tm_base_addr 0xce800000, size 20971520, tm_base_addr_phys 0x0e800000 [ 4.856000] mc_base_addr 0xce400000, size 4194304, mc_base_addr_phys 0x0e400000 [ 4.857000] RDP reserved memory has been adjusted [ 4.857000] TM: base_addr = 0xce700000, phys_addr = 0x0e700000, size = 16MB [ 4.857000] MC: base_addr = 0xce400000, phys_addr = 0x0e400000, size = 3MB [ 4.858000] [ 4.858000] RDP TM memory = 16MB, MC memory = 3MB : Max Possible Bufs <7168> of size <2560>; Allocating <5120> bufs; RDP enum <1> [ 4.859000] WARNING!RDP reserved memories are wasting 5MB of memory, please adjust your reserved memory size [ 4.868000] ++++Runner gso_desc_pool created successfully [ 4.877000] brcmchipinfo: brcm_chipinfo_init entry [ 4.890000] RDPA DS WAN UDP Filter Command Driver [ 4.900000] bcmxtmrt: Broadcom BCM3139B0 ATM/PTM Network Device v0.9 Jan 14 2020 16:10:01 [ 4.902000] Creating CPU ring for queue number 5 with 256 packets descriptor=0xbf12c4ac [ 4.902000] Done initializing Ring 5 Base=0xffdf2000 End=0xffdf3000 calculated entries= 256 RDD Base=0x00c06000 descriptor=0xbf12c4ac [ 4.904000] Creating CPU ring for queue number 6 with 256 packets descriptor=0xbf12c4f8 [ 4.904000] Done initializing Ring 6 Base=0xffdf0000 End=0xffdf1000 calculated entries= 256 RDD Base=0x00c0c000 descriptor=0xbf12c4f8 [ 4.928000] NBUFF v1.0 Initialized [ 4.938000] Initialized fcache state [ 4.939000] Broadcom Packet Flow Cache Char Driver v3.0 Jan 14 2020 16:10:00 Registered<242> [ 4.941000] Created Proc FS /procfs/fcache [ 4.942000] Broadcom Packet Flow Cache registered with netdev chain [ 4.943000] Broadcom Packet Flow Cache learning via BLOG enabled. [ 4.944000] [FHW] pktDbgLvl[0xbf1c3dc4]=0 [ 4.945000] [FHW] fhw_construct: [ 4.946000] Initialized Fcache HW accelerator layer state [ 4.948000] flwStatsThread created [ 4.978000] Constructed Broadcom Packet Flow Cache v3.0 Jan 14 2020 16:10:00 insmod: can't insert '/lib/modules/3.4.11-rt19/extra/bcmxtmcfg.ko': No such file or directory insmod: can't insert '/lib/modules/3.4.11-rt19/extra/adsldd.ko': No such file or directory [ 5.018000] pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0. [ 5.033000] [ 5.033000] LINK DOWN IMP Port [ 5.036000] Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#0 [ 5.037000] Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#1 [ 5.038000] Switch Port#3 (Internal MUX Port#0) connects to Crossbar Port#4 [ 5.039000] Unused MUX Internal Port#1 connects to Crossbar External Port#2 [ 5.040000] Cross Bar MUX Config : Internal Port 00 maps to External Port 04 <reg_val : 0x0000000c> [ 5.041000] Cross Bar MUX Config : Internal Port 01 maps to External Port 02 <reg_val : 0x00000014> [ 5.042000] Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014> [ 5.043000] Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014> [ 5.046000] GPIO 36 is assigned to Serdes Fiber Signal Detection. [ 5.048000] Setting SGMII Calibration value to 0x9 [ 5.053000] Energy detection is used as SFP module insertion detection [ 5.054000] Broadcom BCM63139B0 Ethernet Network Device v0.1 Jan 14 2020 16:10:01 [ 5.057000] dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered [ 5.058000] ++++ disabling GSO on logical_port=0 dev=eth0 [ 5.059000] eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x06180006 : 0x06> MAC : 44:D4:37:44:30:BC [ 5.061000] eth1: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008 : 0x08> MAC : 44:D4:37:44:30:BC [ 5.063000] eth2: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009 : 0x09> MAC : 44:D4:37:44:30:BC [ 5.065000] eth3: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a : 0x0a> MAC : 44:D4:37:44:30:BC [ 5.067000] eth4: <Ext sw port: 3> <Logical : 11> PHY_ID <0x0007f00b : 0x0b> MAC : 44:D4:37:44:30:BC [ 5.070000] Ethernet Auto Power Down and Sleep: Enabled [ 5.072000] Cross bar port 1 of Int switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 5.073000] Ext switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 5.074000] Ext switch port 1; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 5.076000] Ext switch port 2; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 5.077000] Cross bar port 4 of Ext switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 5.079000] All Port Bit Map: 0x0f01: eth0,eth1,eth2,eth3,eth4 [ 5.080000] Chip WAN Only Ports 0001, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0001:eth0 [ 5.081000] Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000: [ 5.082000] Chip LAN Only Ports 0f00, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0f00:eth1,eth2,eth3,eth4 [ 5.083000] WAN/LAN Both Capable Ports 0x0000: [ 5.084000] Creating Enet CPU ring for queue number 1 with 512 packets,Descriptor base=ffdec000 [ 5.084000] Creating Enet CPU ring for queue number 0 with 512 packets,Descriptor base=ffde8000 [ 5.085000] ==⇒ Activate Deep Green Mode [ 5.102000] Initialized Runner Host Layer [ 5.106000] Initialized Runner Unicast Layer [ 5.110000] Initialized Runner L2 Unicast Layer [ 5.115000] Initialized Runner Multicast Layer [ 5.121000] Broadcom Packet Flow Cache HW acceleration enabled. [ 5.129000] Enabled Runner binding to Flow Cache [ 5.140000] Initialized Runner Protocol Layer (700) [ 5.144000] Broadcom Runner Blog Driver Char Driver v0.1 Jan 14 2020 16:10:00 Registered <252> [ 5.183000] NComm TMS V6.80 Kernel Module loaded. [ 5.210000] libata version 3.00 loaded. [ 5.226000] ++++ Powering up SATA block [ 5.241000] writing PORT0_SATA3_PCB_BLOCK_ADDR [ 5.248000] INFO: PLL lock for port0 detected 9100… [ 5.269000] ahci: SSS flag set, parallel bus scan disabled [ 5.285000] ahci strict-ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.293000] ahci strict-ahci.0: flags: 64bit ncq sntf stag clo pmp slum part [ 5.301000] scsi0 : ahci_platform [ 5.304000] ata1: SATA max UDMA/133 mmio [mem 0x8000a000-0x8000bfff] port 0x100 irq 77 [ 5.617000] ata1: SATA link down (SStatus 0 SControl 300) [ 5.630000] Wifi Forwarding Driver is initialized! [ 5.643000] Initializing WLCSM Module [ 5.646000] WLCSM Module loaded successfully [ 5.737000] DHD_FKB_POOL size is:1280 and entry size:2592 [ 5.742000] fkbpool address range: d8800000 ↔ d8b2a000 [ 5.747000] DHD_PKTTAG POOL size is:1280 and entry size:64 [ 5.753000] dhd_module_init in [ 5.756000] dhd_queue_budget = 256 [ 5.759000] dhd_sta_threshold = 2048 [ 5.763000] dhd_if_threshold = 65536 [ 5.767000] no wifi platform data, skip [ 5.771000] dhdpcie_chipmatch: Unsupported vendor 14e4 device a8db [ 5.777000] dhdpcie_pci_probe: chipmatch failed!! [ 5.782000] PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location) [ 5.790000] dhdpcie_init: can't find adapter info for this chip [ 5.796000] PCI: enabling device 0001:01:00.0 (0140 → 0142) [ 5.918000] DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000 [ 5.925000] dhd:0: fw path:/etc/wlan/dhd nv path:(null) [ 5.930000] Creating CPU ring for queue number 7 with 128 packets descriptor=0xbf12c544 [ 5.930000] Done initializing Ring 7 Base=0xffdfe000 End=0xffdfe800 calculated entries= 128 RDD Base=0x00c17000 descriptor=0xbf12c544 [ 5.951000] RDPA returned tx wakeup reg = <0x80299004>, val = <0x10000000> [ 5.958000] RDPA returned rx wakeup reg = <0x8029a004>, val = <0x26000000> [ 5.965000] Scratch pad is not initialized. [ 5.969000] dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 [ 5.979000] dhd_attach: wl0: pre-allocated buffer mode is disabled (allocskbsz=0) [ 5.986000] dhd_attach(): thread:dhd_watchdog_thread:1dc started [ 5.992000] dhd_attach(): thread:dhd0_dpc:1dd started [ 5.998000] dhd_deferred_work_init: work queue initialized [ 6.003000] Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf2d1830 [ 6.003000] Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf2d184c [ 6.013000] wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3 [ 6.028000] Instantiating WFD 0 thread [ 6.038000] dhd:0: fw path:/etc/wlan/dhd nv path:(null) [ 6.043000] dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path= [ 6.064000] dhdpcie_ramsize_adj: Enter [ 6.071000] dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000 [ 6.077000] dhdpcie_download_code_file: download firmware /etc/wlan/dhd/4366c0/rtecdc.bin [ 6.566000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board) [ 6.574000] wl: ID=pci/1/1/0/ [ 6.577000] wl: loading /etc/wlan/bcm43664_EG400R0_1.2_map.bin [ 6.583000] wl: updating srom from flash… [ 6.594000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=20 [ 6.600000] wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=20 [ 6.606000] Replace or append with internal Mac Address [ 6.615000] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. [ 6.818000] PCIe shared addr (0x002a7a8c) read took 196023 usec before dongle is ready [ 6.825000] DMA RX offset from shared Area 0 [ 6.829000] dhdpcie_readshared: Dongle advertizes 2 size indices [ 6.836000] dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it [ 6.844000] H2D DMA WR INDX : array size 544 = 2 * 266 [ 6.849000] D2H DMA RD INDX : array size 32 = 2 * 3 [ 6.854000] D2H DMA WR INDX : array size 32 = 2 * 3 [ 6.859000] H2D DMA RD INDX : array size 544 = 2 * 266 [ 6.865000] ring_info_raw: 56 [ 6.868000] d4 6a 43 00 a4 7b 43 00 b8 7d 43 00 cc 7f 43 00 [ 6.874000] d2 7f 43 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 6.879000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 6.885000] 00 00 00 00 0a 01 00 00 [ 6.889000] dhdpcie_readshared: max H2D queues 266 [ 6.894000] dhd_bus_start: Initializing 266 h2drings [ 6.899000] Scratch pad is not initialized. [ 6.903000] Scratch pad is not initialized. [ 6.908000] Scratch pad is not initialized. [ 6.912000] Scratch pad is not initialized. [ 6.916000] dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512 [ 6.925000] Scratch pad is not initialized. [ 6.929000] dhd_runner_policy_init: N+M Policy = 0 1 (HW) [ 6.978000] dhd_bus_cmn_writeshared: [ 6.981000] 0000: 00 e0 de 18 00 00 00 00 [ 6.986000] dhd_bus_cmn_writeshared: [ 6.989000] 0000: 00 00 c2 00 00 00 00 00 [ 6.994000] dhd_bus_cmn_writeshared: [ 6.997000] 0000: 00 00 e3 18 00 00 00 00 [ 7.002000] dhd_bus_cmn_writeshared: [ 7.006000] 0000: 00 40 e3 18 00 00 00 00 [ 7.010000] dhd_bus_cmn_writeshared: [ 7.014000] 0000: 00 80 c2 00 00 00 00 00 [ 7.018000] dhd_bus_cmn_writeshared: [ 7.022000] 0000: 00 00 40 18 00 00 00 00 [ 7.026000] dhd_bus_cmn_writeshared: [ 7.030000] 0000: 00 10 14 00 [ 7.033000] dhd_bus_cmn_writeshared: [ 7.037000] 0000: 00 c8 e2 18 00 00 00 00 [ 7.041000] dhd_bus_cmn_writeshared: [ 7.045000] 0000: 00 cc e2 18 00 00 00 00 [ 7.049000] dhd_bus_cmn_writeshared: [ 7.053000] 0000: 00 c0 e2 18 00 00 00 00 [ 7.057000] dhd_bus_cmn_writeshared: [ 7.061000] 0000: 00 c4 e2 18 00 00 00 00 [ 7.065000] Attach flowrings pool for 264 rings [ 7.070000] Runner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0> [ 7.078000] Initial configuration [ 7.082000]

[ 7.086000] rx_post_flow_ring_base_addr : c0c20000 [ 7.091000] tx_post_flow_ring_base_addr : 0 [ 7.095000] rx_complete_flow_ring_base_addr : c0c28000 [ 7.101000] tx_complete_flow_ring_base_addr : 0 [ 7.106000] [ 7.107000] r2d_wr_arr_base_addr : ffde0000 [ 7.112000] d2r_rd_arr_base_addr : ffde0402 [ 7.116000] r2d_rd_arr_base_addr : ffde0c00 [ 7.120000] d2r_wr_arr_base_addr : ffde0802 [ 7.125000] tx_post_mgmt_arr_base_addr : ffde1000 [ 7.130000] tx_post_mgmt_arr_base_phys_addr : 18e2d000 [ 7.135000] [ 7.136000] r2d_wr_arr_base_phys_addr : 18e2c000 [ 7.141000] d2r_rd_arr_base_phys_addr : 18e2c402 [ 7.146000] r2d_rd_arr_base_phys_addr : 18e2cc00 [ 7.151000] d2r_wr_arr_base_phys_addr : 18e2c802 [ 7.156000] [ 7.157000] Doorbell ISR : bf2fb35c [ 7.161000] Doorbell CTX : d913ac00 [ 7.165000] Runner DHD Offload initialization complete [ 7.173000] dhd_rx_frame: net device is NOT registered. drop event packet [ 7.174000] dhd_rx_frame: net device is NOT registered. drop event packet [ 7.175000] CUR_ETHERADDR : 6 [ 7.176000] 44 d4 37 44 30 bd [ 7.178000] dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90 [ 7.180000] [ 7.180000] Dongle Host Driver, version 7.14.164.23.cpe4.16L05.0-kdb [ 7.183000] wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0 [ 7.184000] Broadcom PCI Device 0x6313 has allocated with driver pcieport [ 7.185000] Broadcom PCI Device 0x6313 has allocated with driver pcieport [ 7.186000] dhd_module_init out [ 7.847000] –SMP support [ 7.848000] wl: dsl_tx_pkt_flush_len=338 [ 7.849000] wl: norm_wmark_tot=20194, pktc_wmark_tot=20194 [ 7.850000] PCI: enabling device 0000:01:00.0 (0140 → 0142) [ 7.851000] wl: passivemode=1 [ 7.852000] wl1: creating kthread wl1-kthrd [ 7.859000] wl: napimode=0 [ 7.874000] initvars_cis_pci: Not CIS format [ 7.875000] Neither SPROM nor OTP has valid image [ 7.876000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board) [ 7.877000] wl: ID=pci/0/1/0/ [ 7.878000] wl: ID=pci/0/1/0/ [ 7.879000] wl: ID=pci/0/1/0/ [ 7.881000] wl: loading /etc/wlan/bcm43217_map.bin [ 7.883000] srom rev:8 [ 7.886000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=20 [ 7.910000] wl1: allocskbmode=1 currallocskbsz=2300 [ 7.916000] Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf2d1868 [ 7.916000] Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf2d1884 [ 7.918000] wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type skb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc [ 7.919000] Instantiating WFD 1 thread [ 7.920000] wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1 [ 7.921000] wl1: Broadcom BCM43227 802.11 Wireless Controller 7.14.164.23.cpe4.16L05.0-kdb [ 7.922000] dgasp: kerSysRegisterDyingGaspHandler: wl1 registered [ 7.930000] Loading DECT Shim driver [ 7.931000] Initialize DECT Shim layer…. [ 7.932000] Obtained board id string (Si32260_LCQC) [ 7.933000] Obtained Base board id string (EG400R0)Successfully obtained voice parameters [ 7.936000] DECT is disabled by OTP/boardparms or is initialized already [ 7.941000] Loading PCM shim driver [ 8.251000] Endpoint: endpoint_init entry [ 8.252000] ———- Voice board configuration ———- [ 8.253000] Number of FXS lines = 2 [ 8.254000] Number of FXO lines = 0 [ 8.255000] Number of DECT lines = 4 [ 8.256000] Number of failover relay pins= 1 [ 8.257000] ———- [ 8.259000] Endpoint: endpoint_init COMPLETED [ 8.269000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.276000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.280000] ++++ Powering up USB blocks [ 8.608000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller [ 8.609000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 8.610000] ehci-platform ehci-platform.0: irq 105, io mem 0x8000c300 [ 8.617000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 8.618000] hub 1-0:1.0: USB hub found [ 8.619000] hub 1-0:1.0: 2 ports detected [ 8.620000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller [ 8.621000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2 [ 8.622000] ohci-platform ohci-platform.0: irq 104, io mem 0x8000c400 [ 8.678000] hub 2-0:1.0: USB hub found [ 8.679000] hub 2-0:1.0: 2 ports detected [ 8.684000] usbcore: registered new interface driver usblp [ 8.695000] Initializing USB Mass Storage driver… [ 8.696000] usbcore: registered new interface driver usb-storage [ 8.697000] USB Mass Storage support registered. [ 8.717000] Broadcom 802.1Q VLAN Interface, v0.1 [ 8.727000] BRCM TRNG registered [ 8.732000] brcm_otp_init entry /etc/rdpa_init.sh: line 7: bdmf_shell: not found brcm modules loaded Seeding rng from hw trng Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level mounting and populating overlay Initializing iopsys db Static db already initialized ifconfig: SIOCGIFFLAGS: No such device [ 12.101000] procd: - early - Failed to connect to ubus Failed to connect to ubus [ 12.660000] procd: - ubus - [ 13.668000] procd: - init - Please press Enter to activate this console. [ 15.965000] Custom GPIO-based I2C driver version 0.1.1 [ 15.974000] i2c-gpio i2c-gpio.1: using pins 24 (SDA) and 25 (SCL) [ 16.029000] Bluetooth: Core ver 2.20 [ 16.032000] NET: Registered protocol family 31 [ 16.033000] Bluetooth: HCI device and connection manager initialized [ 16.035000] Bluetooth: HCI socket layer initialized [ 16.036000] Bluetooth: L2CAP socket layer initialized [ 16.037000] Bluetooth: SCO socket layer initialized [ 16.043000] Bluetooth: RFCOMM socket layer initialized [ 16.044000] Bluetooth: RFCOMM ver 1.11 [ 16.048000] usbcore: registered new interface driver btusb [ 16.059000] usbcore: registered new interface driver cdc_ether [ 16.065000] usbcore: registered new interface driver cdc_eem [ 16.072000] usbcore: registered new interface driver cdc_ncm [ 16.074000] usbcore: registered new interface driver cdc_wdm [ 16.076000] usbcore: registered new interface driver cdc_mbim [ 16.080000] usbcore: registered new interface driver asix [ 16.081000] usbcore: registered new interface driver kalmia [ 16.083000] usbcore: registered new interface driver rndis_host [ 16.087000] usbcore: registered new interface driver qmi_wwan [ 16.090000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.093000] Netfilter messages via NETLINK v0.30. [ 16.097000] ip_set: protocol 6 [ 16.135000] nf_conntrack version 0.5.0 (7561 buckets, 30244 max) [ 16.147000] gre: GRE over IPv4 demultiplexor driver [ 16.155000] ip_gre: GRE over IPv4 tunneling driver [ 16.205000] xt_time: kernel timezone is -0000 [ 16.214000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.225000] PPTP driver version 0.8.5 [ 16.229000] usbcore: registered new interface driver qcaux [ 16.231000] USB Serial support registered for qcaux [ 16.234000] usbcore: registered new interface driver qcserial [ 16.235000] USB Serial support registered for Qualcomm USB modem [ 16.238000] Registering the dns_resolver key type [ 20.462000] wait instruction: disabled [ 20.482000] Ethernet Auto Power Down and Sleep: Disabled [ 20.496000] Energy Efficient Ethernet changed to disabled Jan 11 21:29:21 peripheral_manager[3427]: Config specified use of led name [WAN_yellow]. But it's not registerd with a led driver. [ 22.230000] Ethernet Auto Power Down and Sleep: Enabled [ 22.238000] Energy Efficient Ethernet: Disabled [ 22.947000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 24.378000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 24.380000] device eth1 entered promiscuous mode [ 24.392000] ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 24.417000] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 24.422000] device eth2 entered promiscuous mode [ 24.451000] ADDRCONF(NETDEV_UP): eth3: link is not ready [ 24.457000] device eth3 entered promiscuous mode [ 24.475000] ADDRCONF(NETDEV_UP): eth4: link is not ready [ 24.480000] device eth4 entered promiscuous mode [ 24.492000] device wl0 entered promiscuous mode [ 24.498000] br-lan: port 5(wl0) entered forwarding state [ 24.503000] br-lan: port 5(wl0) entered forwarding state [ 24.514000] ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 24.520000] device wl1 entered promiscuous mode [ 24.530000] br-lan: port 6(wl1) entered forwarding state [ 24.535000] br-lan: port 6(wl1) entered forwarding state wificontrol.c:396[4600]: router_mode(): Router mode wificontrol.c:135[4600]: collect_intenos(): network lan 192.168.0.1/255.255.255.0 wificontrol.c:141[4600]: collect_intenos(): Parsing arp table /proc/net/arp [ 26.457000] br-lan: port 5(wl0) entered disabled state [ 26.536000] br-lan: port 6(wl1) entered forwarding state [ 26.622000] wfd_registerdevice Successfully registered dev wl0.1 ifidx 1 wfd_idx 0 [ 26.632000] wfd_registerdevice Successfully registered dev wl0.2 ifidx 2 wfd_idx 0 [ 26.643000] wfd_registerdevice Successfully registered dev wl0.3 ifidx 3 wfd_idx 0 [ 26.650000] dhd_wmf_igs_broadcast: WMF: send failure [ 26.651000] IGMP Query send failed [ 27.357000] br-lan: port 5(wl0) entered forwarding state [ 27.362000] br-lan: port 5(wl0) entered forwarding state [ 27.734000] dhd_set_monitor: Mismatched params, return [ 28.288000] br-lan: port 6(wl1) entered disabled state [ 28.456000] wfd_registerdevice Successfully registered dev wl1.1 ifidx 1 wfd_idx 1 [ 28.469000] wfd_registerdevice Successfully registered dev wl1.2 ifidx 2 wfd_idx 1 [ 28.487000] wfd_registerdevice Successfully registered dev wl1.3 ifidx 3 wfd_idx 1 [ 28.897000] br-lan: port 6(wl1) entered forwarding state [ 28.898000] br-lan: port 6(wl1) entered forwarding state [ 29.067000] wlc_dfs_updown_cb:got callback from updown. interface up [ 29.368000] br-lan: port 5(wl0) entered forwarding state [ 30.904000] br-lan: port 6(wl1) entered forwarding state


Once booted, you can press enter to activate the console, but will then be sent straight to a regular Linux login-screen, not a ready-to-use root-shell.

Only known user with a valid login-shell on the the device is “root”.

root@iopsys:~# lspci 
00:00.0 Class 0604: 14e4:6313
01:00.0 Class 0280: 14e4:a8db
00:00.0 Class 0604: 14e4:6313
01:00.0 Class 0280: 14e4:4365
root@iopsys:~# lsusb 
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0003
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0001

root@iopsys:~# uname -a Linux iopsys 4.1.38 #3 SMP PREEMPT Sun Sep 27 03:44:03 UTC 2020 armv7l GNU/Linux root@iopsys:~# lsmod asix 16977 0 bcm_enet 166286 1 wl bcm_ingqos 10505 0 bcm_usb 1391 0 bcmmcast 49041 4 dhd,wlemf,wfd bcmtrng 2706 0 bcmvlan 87889 0 bdmf 1232593 8 dhd,wfd,pktrunner,bcm_enet,rdpa_cmd,rdpa_mw,rdpa,rdpa_gpl bluetooth 283139 7 hci_uart,btusb,btbcm,btintel,rfcomm btbcm 3717 1 btusb btintel 1168 1 btusb btusb 26520 0 cdc_eem 2064 0 cdc_ether 3941 1 rndis_host cdc_mbim 4174 0 cdc_ncm 12978 1 cdc_mbim cdc_wdm 7845 2 qmi_wwan,cdc_mbim chipinfo 1259 0 cifs 213038 0 dhd 491228 0 dns_resolver 4115 1 cifs dsphal 53287 7 ehci_hcd 34480 2 ehci_pci,ehci_platform ehci_pci 2864 0 ehci_platform 4089 0 firmware_class 3617 2 btusb,btbcm gre 3225 1 ip_gre hci_uart 4093 0 i2c_algo_bit 4659 1 i2c_gpio i2c_gpio 2793 1 i2c_gpio_custom 914 0 ip_gre 8262 0 ip_set 21483 12 xt_set,ip_set_list_set,ip_set_hash_netport,ip_set_hash_net,ip_set_hash_netiface,ip_set_hash_ipportnet,ip_set_hash_ipport,ip_set_hash_ipportip,ip_set_hash_ip,ip_set_bitmap_port,ip_set_bitmap_ipmac,ip_set_bitmap_ip ip_set_bitmap_ip 6792 0 ip_set_bitmap_ipmac 6748 0 ip_set_bitmap_port 6016 0 ip_set_hash_ip 16495 0 ip_set_hash_ipport 16731 0 ip_set_hash_ipportip 17577 0 ip_set_hash_ipportnet 22034 0 ip_set_hash_net 18936 2 ip_set_hash_netiface 20862 0 ip_set_hash_netport 20596 0 ip_set_list_set 7979 1 ip_tables 9373 4 iptable_raw,iptable_mangle,iptable_filter,iptable_nat ip6_tables 9663 3 ip6table_raw,ip6table_mangle,ip6table_filter ip6t_REJECT 1172 2 ip6table_filter 778 1 ip6table_mangle 1079 1 ip6table_raw 725 0 ipt_MASQUERADE 740 1 ipt_REJECT 1038 2 iptable_filter 832 1 iptable_mangle 957 1 iptable_nat 1074 1 iptable_raw 779 0 kalmia 2483 0 libphy 19834 1 asix md4 3032 0 mii 3519 2 asix,usbnet nciTMSkmod 369759 0 nf_conntrack 62746 20 nf_conntrack_ipv6,xt_state,xt_conntrack,xt_CT,xt_connmark,nf_nat_tftp,nf_nat_rtsp,nf_nat_pptp,nf_nat_irc,nf_nat_ftp,nf_conntrack_tftp,nf_conntrack_rtsp,nf_conntrack_pptp,nf_conntrack_proto_gre,nf_conntrack_irc,nf_conntrack_ftp,nf_nat_masquerade_ipv4,nf_conntrack_ipv4,nf_nat_ipv4,nf_nat nf_conntrack_ftp 5808 1 nf_nat_ftp nf_conntrack_ipv4 10428 14 nf_conntrack_ipv6 5673 5 nf_conntrack_irc 3103 1 nf_nat_irc nf_conntrack_pptp 3576 1 nf_nat_pptp nf_conntrack_proto_gre 3046 1 nf_conntrack_pptp nf_conntrack_rtsp 6923 1 nf_nat_rtsp nf_conntrack_tftp 2863 1 nf_nat_tftp nf_defrag_ipv4 1032 1 nf_conntrack_ipv4 nf_defrag_ipv6 13578 1 nf_conntrack_ipv6 nf_nat 9760 9 nf_nat_tftp,nf_nat_rtsp,nf_nat_pptp,nf_nat_proto_gre,nf_nat_irc,nf_nat_ftp,nf_nat_redirect,nf_nat_masquerade_ipv4,nf_nat_ipv4 nf_nat_ftp 1344 0 nf_nat_ipv4 3931 1 iptable_nat nf_nat_irc 1064 0 nf_nat_masquerade_ipv4 3031 1 ipt_MASQUERADE nf_nat_pptp 1984 0 nf_nat_proto_gre 913 1 nf_nat_pptp nf_nat_redirect 930 1 xt_REDIRECT nf_nat_rtsp 3195 0 nf_nat_tftp 655 0 nf_reject_ipv4 1822 1 ipt_REJECT nf_reject_ipv6 2107 1 ip6t_REJECT nfnetlink 4375 2 nfnetlink_queue,ip_set nfnetlink_queue 8283 0 ohci_hcd 25025 2 ohci_pci,ohci_platform ohci_pci 2257 0 ohci_platform 3565 0 otp 2015 0 pktflow 154456 1 pktrunner pktrunner 206960 0 pwrmngtd 2377 0 qcaux 1094 0 qcserial 4512 0 qmi_wwan 10816 0 rdpa 1139622 2 wfd,bcm_enet rdpa_cmd 69928 0 rdpa_gpl 16577 9 bcm_ingqos,bcmvlan,dhd,wfd,pktrunner,bcm_enet,rdpa_cmd,rdpa_mw,rdpa rdpa_gpl_ext 855 0 rdpa_mw 23751 1 bcmvlan rfcomm 28863 0 rndis_host 4746 0 slicslac 598387 1 ts_bm 1512 0 ts_fsm 2775 0 ts_kmp 1432 0 usb_storage 37368 0 usblp 9153 0 usbnet 15996 8 qmi_wwan,rndis_host,kalmia,asix,cdc_mbim,cdc_ncm,cdc_eem,cdc_ether wfd 15326 2 wl,dhd wl 4730719 0 wlcsm 5071 11 wl,dhd,wlemf wlemf 69223 2 wl,dhd xhci_hcd 83959 1 xhci_plat_hcd xhci_plat_hcd 3484 0 xt_CT 2627 0 xt_DSCP 1540 0 xt_LOG 893 0 xt_REDIRECT 859 0 xt_SKIPLOG 577 0 xt_TCPMSS 2686 2 xt_comment 565126 xt_connmark 1242 0 xt_conntrack 2542 18 xt_dscp 1204 0 xt_id 560 0 xt_length 823 0 xt_limit 1315 20 xt_mac 685 0 xt_mark 762 0 xt_multiport 1374 0 xt_recent 6754 4 xt_set 6573 0 xt_state 847 0 xt_statistic 927 0 xt_string 834 0 xt_time 1759 0 root@iopsys:~# zcat /proc/config.gz # # Automatically generated file; DO NOT EDIT. # Linux/arm 4.1.38 Kernel Configuration # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_HAVE_PROC_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ZONE_DMA=y CONFIG_NEED_DMA_MAP_STATE=y CONFIG_ARCH_SUPPORTS_UPROBES=y CONFIG_VECTORS_BASE=0xffff0000 # CONFIG_ARM_PATCH_PHYS_VIRT is not set CONFIG_NEED_MACH_MEMORY_H=y CONFIG_PHYS_OFFSET=0x00000000 CONFIG_GENERIC_BUG=y CONFIG_PGTABLE_LEVELS=2 CONFIG_DEFCONFIG_LIST=“/lib/modules/$UNAME_RELEASE/.config” CONFIG_IRQ_WORK=y CONFIG_BUILDTIME_EXTABLE_SORT=y

# # General setup # CONFIG_INIT_ENV_ARG_LIMIT=32 CONFIG_CROSS_COMPILE=“” # CONFIG_COMPILE_TEST is not set CONFIG_LOCALVERSION=“” # CONFIG_LOCALVERSION_AUTO is not set CONFIG_HAVE_KERNEL_GZIP=y CONFIG_HAVE_KERNEL_LZMA=y CONFIG_HAVE_KERNEL_XZ=y CONFIG_HAVE_KERNEL_LZO=y CONFIG_HAVE_KERNEL_LZ4=y CONFIG_KERNEL_GZIP=y # CONFIG_KERNEL_LZMA is not set # CONFIG_KERNEL_XZ is not set # CONFIG_KERNEL_LZO is not set # CONFIG_KERNEL_LZ4 is not set CONFIG_DEFAULT_HOSTNAME=“(none)” CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_CROSS_MEMORY_ATTACH is not set # CONFIG_FHANDLE is not set # CONFIG_USELIB is not set # CONFIG_AUDIT is not set

# # IRQ subsystem # CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_IRQ_SHOW=y CONFIG_GENERIC_IRQ_SHOW_LEVEL=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_IRQ_DOMAIN=y CONFIG_IRQ_DOMAIN_HIERARCHY=y CONFIG_HANDLE_DOMAIN_IRQ=y # CONFIG_IRQ_DOMAIN_DEBUG is not set CONFIG_IRQ_FORCED_THREADING=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_ARCH_HAS_TICK_BROADCAST=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y

# # Timers subsystem # CONFIG_HZ_PERIODIC=y # CONFIG_NO_HZ_IDLE is not set # CONFIG_NO_HZ_FULL is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set

# # CPU/Task time and stats accounting # CONFIG_TICK_CPU_ACCOUNTING=y # CONFIG_VIRT_CPU_ACCOUNTING_GEN is not set # CONFIG_IRQ_TIME_ACCOUNTING is not set # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_TASKSTATS=y CONFIG_TASK_DELAY_ACCT=y CONFIG_TASK_XACCT=y CONFIG_TASK_IO_ACCOUNTING=y

# # RCU Subsystem # CONFIG_PREEMPT_RCU=y CONFIG_SRCU=y # CONFIG_TASKS_RCU is not set CONFIG_RCU_STALL_COMMON=y # CONFIG_RCU_USER_QS is not set CONFIG_RCU_FANOUT=32 CONFIG_RCU_FANOUT_LEAF=16 # CONFIG_RCU_FANOUT_EXACT is not set # CONFIG_TREE_RCU_TRACE is not set # CONFIG_RCU_BOOST is not set CONFIG_RCU_KTHREAD_PRIO=0 # CONFIG_RCU_NOCB_CPU is not set # CONFIG_RCU_EXPEDITE_BOOT is not set CONFIG_BUILD_BIN2C=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_LOG_CPU_MAX_BUF_SHIFT=12 CONFIG_GENERIC_SCHED_CLOCK=y # CONFIG_CGROUPS is not set # CONFIG_CHECKPOINT_RESTORE is not set # CONFIG_NAMESPACES is not set # CONFIG_SCHED_AUTOGROUP is not set # CONFIG_SYSFS_DEPRECATED is not set # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE=“” CONFIG_RD_GZIP=y # CONFIG_RD_BZIP2 is not set # CONFIG_RD_LZMA is not set # CONFIG_RD_XZ is not set # CONFIG_RD_LZO is not set # CONFIG_RD_LZ4 is not set # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y CONFIG_ANON_INODES=y CONFIG_HAVE_UID16=y CONFIG_BPF=y CONFIG_EXPERT=y # CONFIG_UID16 is not set CONFIG_MULTIUSER=y # CONFIG_SGETMASK_SYSCALL is not set # CONFIG_SYSFS_SYSCALL is not set CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y # CONFIG_BPF_SYSCALL is not set CONFIG_SHMEM=y # CONFIG_AIO is not set # CONFIG_ADVISE_SYSCALLS is not set CONFIG_PCI_QUIRKS=y CONFIG_EMBEDDED=y CONFIG_HAVE_PERF_EVENTS=y CONFIG_PERF_USE_VMALLOC=y

# # Kernel Performance Events And Counters # # CONFIG_PERF_EVENTS is not set # CONFIG_VM_EVENT_COUNTERS is not set # CONFIG_COMPAT_BRK is not set CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_SYSTEM_TRUSTED_KEYRING is not set # CONFIG_PROFILING is not set CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set # CONFIG_JUMP_LABEL is not set # CONFIG_UPROBES is not set # CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y CONFIG_ARCH_USE_BUILTIN_BSWAP=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_OPTPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_DMA_ATTRS=y CONFIG_HAVE_DMA_CONTIGUOUS=y CONFIG_GENERIC_SMP_IDLE_THREAD=y CONFIG_GENERIC_IDLE_POLL_SETUP=y CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y CONFIG_HAVE_CLK=y CONFIG_HAVE_DMA_API_DEBUG=y CONFIG_HAVE_PERF_REGS=y CONFIG_HAVE_PERF_USER_STACK_DUMP=y CONFIG_HAVE_ARCH_JUMP_LABEL=y CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y CONFIG_HAVE_CC_STACKPROTECTOR=y # CONFIG_CC_STACKPROTECTOR is not set CONFIG_CC_STACKPROTECTOR_NONE=y # CONFIG_CC_STACKPROTECTOR_REGULAR is not set # CONFIG_CC_STACKPROTECTOR_STRONG is not set CONFIG_HAVE_CONTEXT_TRACKING=y CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y CONFIG_HAVE_MOD_ARCH_SPECIFIC=y CONFIG_MODULES_USE_ELF_REL=y CONFIG_ARCH_HAS_ELF_RANDOMIZE=y CONFIG_CLONE_BACKWARDS=y CONFIG_OLD_SIGSUSPEND3=y CONFIG_OLD_SIGACTION=y

# # GCOV-based kernel profiling # # CONFIG_GCOV_KERNEL is not set CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y CONFIG_BASE_SMALL=0 CONFIG_MODULES=y # CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set # CONFIG_MODULE_SIG is not set # CONFIG_MODULE_COMPRESS is not set CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_BSGLIB is not set # CONFIG_BLK_DEV_INTEGRITY is not set # CONFIG_BLK_CMDLINE_PARSER is not set

# # Partition Types # CONFIG_PARTITION_ADVANCED=y # CONFIG_ACORN_PARTITION is not set # CONFIG_AIX_PARTITION is not set # CONFIG_OSF_PARTITION is not set # CONFIG_AMIGA_PARTITION is not set # CONFIG_ATARI_PARTITION is not set # CONFIG_MAC_PARTITION is not set CONFIG_MSDOS_PARTITION=y # CONFIG_BSD_DISKLABEL is not set # CONFIG_MINIX_SUBPARTITION is not set # CONFIG_SOLARIS_X86_PARTITION is not set # CONFIG_UNIXWARE_DISKLABEL is not set CONFIG_LDM_PARTITION=y # CONFIG_LDM_DEBUG is not set # CONFIG_SGI_PARTITION is not set # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set # CONFIG_KARMA_PARTITION is not set CONFIG_EFI_PARTITION=y # CONFIG_SYSV68_PARTITION is not set # CONFIG_CMDLINE_PARTITION is not set

# # IO Schedulers # CONFIG_IOSCHED_NOOP=y # CONFIG_IOSCHED_DEADLINE is not set # CONFIG_IOSCHED_CFQ is not set CONFIG_DEFAULT_NOOP=y CONFIG_DEFAULT_IOSCHED=“noop” CONFIG_UNINLINE_SPIN_UNLOCK=y CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y CONFIG_MUTEX_SPIN_ON_OWNER=y CONFIG_RWSEM_SPIN_ON_OWNER=y CONFIG_LOCK_SPIN_ON_OWNER=y # CONFIG_FREEZER is not set

# # System Type # CONFIG_MMU=y # CONFIG_ARCH_MULTIPLATFORM is not set # CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_CLPS711X is not set # CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set # CONFIG_ARCH_FOOTBRIDGE is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_DOVE is not set # CONFIG_ARCH_MV78XX0 is not set # CONFIG_ARCH_ORION5X is not set # CONFIG_ARCH_MMP is not set # CONFIG_ARCH_KS8695 is not set # CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_LPC32XX is not set # CONFIG_ARCH_PXA is not set # CONFIG_ARCH_SHMOBILE_LEGACY is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C24XX is not set # CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP1 is not set CONFIG_ARCH_BCM63XX=y CONFIG_CPU_LITTLE_ENDIAN=y # CONFIG_CPU_BIG_ENDIAN is not set # CONFIG_BUZZZ is not set # CONFIG_BUZZZ_FUNC is not set # CONFIG_BUZZZ_PMON is not set # CONFIG_BUZZZ_KEVT is not set CONFIG_PLAT_CA9_MPCORE=y CONFIG_PLAT_CA9_SMP=y # CONFIG_PLAT_CA9_MPCORE_TIMER is not set # CONFIG_PLAT_B15_CORE is not set # CONFIG_PLAT_B15_SMP is not set # CONFIG_CACHE_L310 is not set # CONFIG_PLAT_BCM63XX_AMBA_PL011 is not set # CONFIG_PLAT_BCM63XX_AMBA_PL081 is not set # CONFIG_PLAT_BCM63XX_EMMC is not set CONFIG_PLAT_BCM63XX_UART=y CONFIG_PLAT_BCM63XX_EXT_TIMER=y # CONFIG_PLAT_BCM63XX_ACP is not set CONFIG_ARM_BCM63XX_CPUFREQ=y CONFIG_PLAT_BCM63138=y # CONFIG_BCM_PCIE_PLATFORM is not set

# # Processor Type # CONFIG_CPU_V7=y CONFIG_CPU_32v6K=y CONFIG_CPU_32v7=y CONFIG_CPU_ABRT_EV7=y CONFIG_CPU_PABRT_V7=y CONFIG_CPU_CACHE_V7=y CONFIG_CPU_CACHE_VIPT=y CONFIG_CPU_COPY_V6=y CONFIG_CPU_TLB_V7=y CONFIG_CPU_HAS_ASID=y CONFIG_CPU_CP15=y CONFIG_CPU_CP15_MMU=y

# # Processor Features # # CONFIG_ARM_LPAE is not set # CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_ARM_THUMB=y # CONFIG_ARM_THUMBEE is not set CONFIG_ARM_VIRT_EXT=y CONFIG_SWP_EMULATE=y # CONFIG_CPU_ICACHE_DISABLE is not set # CONFIG_CPU_BPREDICT_DISABLE is not set CONFIG_KUSER_HELPERS=y # CONFIG_VDSO is not set CONFIG_OUTER_CACHE=y CONFIG_OUTER_CACHE_SYNC=y CONFIG_CACHE_L2X0=y # CONFIG_PL310_ERRATA_588369 is not set # CONFIG_PL310_ERRATA_727915 is not set # CONFIG_PL310_ERRATA_753970 is not set # CONFIG_PL310_ERRATA_769419 is not set CONFIG_ARM_L1_CACHE_SHIFT=5 CONFIG_ARM_DMA_MEM_BUFFERABLE=y # CONFIG_ARM_KERNMEM_PERMS is not set CONFIG_MULTI_IRQ_HANDLER=y # CONFIG_ARM_ERRATA_430973 is not set # CONFIG_ARM_ERRATA_458693 is not set # CONFIG_ARM_ERRATA_460075 is not set # CONFIG_ARM_ERRATA_742230 is not set # CONFIG_ARM_ERRATA_742231 is not set # CONFIG_ARM_ERRATA_643719 is not set # CONFIG_ARM_ERRATA_720789 is not set # CONFIG_ARM_ERRATA_743622 is not set # CONFIG_ARM_ERRATA_751472 is not set CONFIG_ARM_ERRATA_754322=y # CONFIG_ARM_ERRATA_754327 is not set CONFIG_ARM_ERRATA_764369=y # CONFIG_ARM_ERRATA_775420 is not set # CONFIG_ARM_ERRATA_798181 is not set # CONFIG_ARM_ERRATA_773022 is not set

# # Bus support # CONFIG_PCI=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_DOMAINS_GENERIC=y CONFIG_PCI_SYSCALL=y # CONFIG_PCI_MSI is not set # CONFIG_PCI_DEBUG is not set # CONFIG_PCI_REALLOC_ENABLE_AUTO is not set # CONFIG_PCI_STUB is not set # CONFIG_PCI_IOV is not set # CONFIG_PCI_PRI is not set # CONFIG_PCI_PASID is not set

# # PCI host controller drivers # # CONFIG_PCI_HOST_GENERIC is not set # CONFIG_PCI_LAYERSCAPE is not set # CONFIG_PCIE_IPROC is not set CONFIG_PCIEPORTBUS=y # CONFIG_PCIEAER is not set CONFIG_PCIEASPM=y # CONFIG_PCIEASPM_DEBUG is not set CONFIG_PCIEASPM_DEFAULT=y # CONFIG_PCIEASPM_POWERSAVE is not set # CONFIG_PCIEASPM_PERFORMANCE is not set # CONFIG_PCCARD is not set

# # Kernel Features # CONFIG_HAVE_SMP=y CONFIG_SMP=y CONFIG_SMP_ON_UP=y # CONFIG_ARM_CPU_TOPOLOGY is not set CONFIG_HAVE_ARM_SCU=y # CONFIG_HAVE_ARM_ARCH_TIMER is not set # CONFIG_MCPM is not set # CONFIG_BIG_LITTLE is not set CONFIG_VMSPLIT_3G=y # CONFIG_VMSPLIT_2G is not set # CONFIG_VMSPLIT_1G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_NR_CPUS=2 CONFIG_HOTPLUG_CPU=y # CONFIG_ARM_PSCI is not set CONFIG_ARCH_NR_GPIO=0 # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y CONFIG_PREEMPT_COUNT=y CONFIG_HZ_FIXED=0 # CONFIG_HZ_100 is not set # CONFIG_HZ_200 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set # CONFIG_HZ_500 is not set CONFIG_HZ_1000=y CONFIG_HZ=1000 # CONFIG_SCHED_HRTICK is not set # CONFIG_THUMB2_KERNEL is not set CONFIG_AEABI=y CONFIG_OABI_COMPAT=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set CONFIG_HAVE_ARCH_PFN_VALID=y # CONFIG_HIGHMEM is not set CONFIG_ARCH_WANT_GENERAL_HUGETLB=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_HAVE_MEMBLOCK=y CONFIG_NO_BOOTMEM=y # CONFIG_HAVE_BOOTMEM_INFO_NODE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_COMPACTION is not set # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 # CONFIG_BOUNCE is not set # CONFIG_KSM is not set CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 # CONFIG_CLEANCACHE is not set # CONFIG_FRONTSWAP is not set # CONFIG_CMA is not set # CONFIG_ZPOOL is not set # CONFIG_ZBUD is not set # CONFIG_ZSMALLOC is not set CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_ALIGNMENT_TRAP=y # CONFIG_UACCESS_WITH_MEMCPY is not set CONFIG_SECCOMP=y CONFIG_SWIOTLB=y CONFIG_IOMMU_HELPER=y # CONFIG_XEN is not set

# # Boot options # CONFIG_USE_OF=y CONFIG_ATAGS=y # CONFIG_DEPRECATED_PARAM_STRUCT is not set CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 # CONFIG_ARM_APPENDED_DTB is not set CONFIG_CMDLINE=“console=ttyS0,115200 debug irqaffinity=0 coherent_pool=1M cpuidle_sysfs_switch earlyprintk rw noinitrd” # CONFIG_CMDLINE_FROM_BOOTLOADER is not set CONFIG_CMDLINE_EXTEND=y # CONFIG_CMDLINE_FORCE is not set # CONFIG_XIP_KERNEL is not set # CONFIG_CRASH_DUMP is not set # CONFIG_AUTO_ZRELADDR is not set

# # CPU Power Management #

# # CPU Frequency scaling # CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_GOV_COMMON=y CONFIG_CPU_FREQ_STAT=y # CONFIG_CPU_FREQ_STAT_DETAILS is not set # CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set # CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set # CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set # CONFIG_CPU_FREQ_DEFAULT_GOV_INTERACTIVE is not set # CONFIG_CPU_FREQ_GOV_PERFORMANCE is not set # CONFIG_CPU_FREQ_GOV_POWERSAVE is not set CONFIG_CPU_FREQ_GOV_USERSPACE=y CONFIG_CPU_FREQ_GOV_ONDEMAND=y CONFIG_CPU_FREQ_GOV_INTERACTIVE=y # CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set

# # CPU frequency scaling drivers # # CONFIG_CPUFREQ_DT is not set # CONFIG_ARM_KIRKWOOD_CPUFREQ is not set

# # CPU Idle # CONFIG_CPU_IDLE=y CONFIG_CPU_IDLE_GOV_LADDER=y CONFIG_CPU_IDLE_GOV_MENU=y

# # ARM CPU Idle Drivers # # CONFIG_ARM_CPUIDLE is not set # CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set

# # Floating point emulation #

# # At least one emulation must be selected # # CONFIG_FPE_NWFPE is not set CONFIG_FPE_FASTFPE=y # CONFIG_VFP is not set

# # Userspace binary formats # CONFIG_BINFMT_ELF=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set CONFIG_BINFMT_SCRIPT=y # CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_COREDUMP=y

# # Power management options # # CONFIG_SUSPEND is not set # CONFIG_HIBERNATION is not set # CONFIG_PM is not set CONFIG_CPU_PM=y CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_ARM_CPU_SUSPEND is not set CONFIG_ARCH_HIBERNATION_POSSIBLE=y CONFIG_NET=y

# # Networking options # CONFIG_PACKET=y # CONFIG_PACKET_DIAG is not set CONFIG_UNIX=y # CONFIG_UNIX_DIAG is not set CONFIG_XFRM=y CONFIG_XFRM_ALGO=y CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set # CONFIG_XFRM_STATISTICS is not set CONFIG_NET_KEY=y # CONFIG_NET_KEY_MIGRATE is not set CONFIG_INET=y CONFIG_BLOG=y CONFIG_BLOG_IPV6=y CONFIG_BLOG_MCAST=y CONFIG_BLOG_GRE=y # CONFIG_BLOG_FEATURE is not set CONFIG_BLOG_L2TP=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y # CONFIG_IP_FIB_TRIE_STATS is not set CONFIG_IP_MULTIPLE_TABLES=y # CONFIG_IP_ROUTE_MULTIPATH is not set # CONFIG_IP_ROUTE_VERBOSE is not set CONFIG_IP_ROUTE_CLASSID=y # CONFIG_IP_PNP is not set # CONFIG_NET_IPIP is not set CONFIG_NET_IPGRE_DEMUX=m CONFIG_NET_IP_TUNNEL=y CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y # CONFIG_IP_MROUTE_MULTIPLE_TABLES is not set # CONFIG_IP_PIMSM_V1 is not set # CONFIG_IP_PIMSM_V2 is not set CONFIG_SYN_COOKIES=y # CONFIG_NET_IPVTI is not set CONFIG_NET_UDP_TUNNEL=y # CONFIG_NET_FOU is not set # CONFIG_NET_FOU_IP_TUNNELS is not set # CONFIG_GENEVE is not set CONFIG_INET_AH=y CONFIG_INET_ESP=y # CONFIG_INET_IPCOMP is not set # CONFIG_INET_XFRM_TUNNEL is not set CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y # CONFIG_INET_XFRM_MODE_BEET is not set # CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG=“cubic” # CONFIG_TCP_MD5SIG is not set CONFIG_IPV6=y CONFIG_IPV6_ROUTER_PREF=y # CONFIG_IPV6_ROUTE_INFO is not set # CONFIG_IPV6_OPTIMISTIC_DAD is not set CONFIG_INET6_AH=y CONFIG_INET6_ESP=y # CONFIG_INET6_IPCOMP is not set # CONFIG_IPV6_MIP6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set CONFIG_INET6_TUNNEL=y CONFIG_INET6_XFRM_MODE_TRANSPORT=y CONFIG_INET6_XFRM_MODE_TUNNEL=y # CONFIG_INET6_XFRM_MODE_BEET is not set # CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set # CONFIG_IPV6_VTI is not set CONFIG_IPV6_SIT=y CONFIG_IPV6_SIT_6RD=y CONFIG_IPV6_NDISC_NODETYPE=y CONFIG_IPV6_TUNNEL=y # CONFIG_IPV6_GRE is not set CONFIG_IPV6_MULTIPLE_TABLES=y # CONFIG_IPV6_SUBTREES is not set CONFIG_IPV6_MROUTE=y # CONFIG_IPV6_MROUTE_MULTIPLE_TABLES is not set CONFIG_IPV6_PIMSM_V2=y # CONFIG_MPTCP is not set CONFIG_DEFAULT_MPTCP_PM=“default” # CONFIG_NETWORK_SECMARK is not set # CONFIG_NET_PTP_CLASSIFY is not set # CONFIG_NETWORK_PHY_TIMESTAMPING is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_NETFILTER_ADVANCED=y # CONFIG_BRIDGE_NETFILTER is not set

# # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m # CONFIG_NETFILTER_NETLINK_ACCT is not set CONFIG_NETFILTER_NETLINK_QUEUE=m # CONFIG_NETFILTER_NETLINK_LOG is not set CONFIG_NF_CONNTRACK=m CONFIG_NF_LOG_COMMON=m CONFIG_NF_CONNTRACK_MARK=y CONFIG_NF_CONNTRACK_ZONES=y CONFIG_NF_CONNTRACK_PROCFS=y # CONFIG_NF_CONNTRACK_EVENTS is not set # CONFIG_NF_CONNTRACK_TIMEOUT is not set # CONFIG_NF_CONNTRACK_TIMESTAMP is not set # CONFIG_NF_CT_PROTO_DCCP is not set CONFIG_NF_CT_PROTO_GRE=m # CONFIG_NF_CT_PROTO_SCTP is not set # CONFIG_NF_CT_PROTO_UDPLITE is not set # CONFIG_NF_CT_PROTO_ESP is not set # CONFIG_NF_CONNTRACK_AMANDA is not set CONFIG_NF_CONNTRACK_FTP=m CONFIG_NF_CONNTRACK_H323=m CONFIG_NF_CONNTRACK_IRC=m # CONFIG_NF_CONNTRACK_NETBIOS_NS is not set # CONFIG_NF_CONNTRACK_SNMP is not set CONFIG_NF_CONNTRACK_PPTP=m # CONFIG_NF_CONNTRACK_SANE is not set CONFIG_NF_CONNTRACK_SIP=m # CONFIG_NF_CONNTRACK_IPSEC is not set CONFIG_NF_CONNTRACK_TFTP=m CONFIG_NF_DYNDSCP=m CONFIG_NF_CONNTRACK_RTSP=m # CONFIG_NETFILTER_XT_MATCH_LAYER7 is not set # CONFIG_NETFILTER_XT_TARGET_DC is not set # CONFIG_NF_CT_NETLINK is not set # CONFIG_NF_CT_NETLINK_TIMEOUT is not set # CONFIG_NETFILTER_NETLINK_QUEUE_CT is not set CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y # CONFIG_NF_NAT_AMANDA is not set CONFIG_NF_NAT_FTP=m CONFIG_NF_NAT_IRC=m CONFIG_NF_NAT_SIP=m CONFIG_NF_NAT_TFTP=m CONFIG_NF_NAT_REDIRECT=m # CONFIG_NF_TABLES is not set CONFIG_NETFILTER_XTABLES=y

# # Xtables combined modules # CONFIG_NETFILTER_XT_MARK=m CONFIG_NETFILTER_XT_CONNMARK=m CONFIG_NETFILTER_XT_SET=m

# # Xtables targets # # CONFIG_NETFILTER_XT_TARGET_CHECKSUM is not set # CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set # CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set CONFIG_NETFILTER_XT_TARGET_CT=m CONFIG_NETFILTER_XT_TARGET_DSCP=m # CONFIG_NETFILTER_XT_TARGET_HL is not set # CONFIG_NETFILTER_XT_TARGET_HMARK is not set # CONFIG_NETFILTER_XT_TARGET_IDLETIMER is not set CONFIG_NETFILTER_XT_TARGET_LOG=m CONFIG_NETFILTER_XT_TARGET_MARK=m CONFIG_NETFILTER_XT_NAT=m # CONFIG_NETFILTER_XT_TARGET_NETMAP is not set # CONFIG_NETFILTER_XT_TARGET_NFLOG is not set # CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set CONFIG_NETFILTER_XT_TARGET_NOTRACK=m # CONFIG_NETFILTER_XT_TARGET_RATEEST is not set CONFIG_NETFILTER_XT_TARGET_REDIRECT=m # CONFIG_NETFILTER_XT_TARGET_TEE is not set # CONFIG_NETFILTER_XT_TARGET_TPROXY is not set # CONFIG_NETFILTER_XT_TARGET_TRACE is not set CONFIG_NETFILTER_XT_TARGET_TCPMSS=m # CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set CONFIG_NETFILTER_XT_TARGET_SKIPLOG=m

# # Xtables matches # # CONFIG_NETFILTER_XT_MATCH_ADDRTYPE is not set # CONFIG_NETFILTER_XT_MATCH_BPF is not set # CONFIG_NETFILTER_XT_MATCH_CLUSTER is not set CONFIG_NETFILTER_XT_MATCH_COMMENT=m # CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set # CONFIG_NETFILTER_XT_MATCH_CONNLABEL is not set # CONFIG_NETFILTER_XT_MATCH_CONNLIMIT is not set CONFIG_NETFILTER_XT_MATCH_CONNMARK=m CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m # CONFIG_NETFILTER_XT_MATCH_CPU is not set # CONFIG_NETFILTER_XT_MATCH_DCCP is not set # CONFIG_NETFILTER_XT_MATCH_DEVGROUP is not set CONFIG_NETFILTER_XT_MATCH_DSCP=m # CONFIG_NETFILTER_XT_MATCH_ECN is not set # CONFIG_NETFILTER_XT_MATCH_ESP is not set # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set # CONFIG_NETFILTER_XT_MATCH_HELPER is not set # CONFIG_NETFILTER_XT_MATCH_HL is not set # CONFIG_NETFILTER_XT_MATCH_IPCOMP is not set CONFIG_NETFILTER_XT_MATCH_ID=m # CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set # CONFIG_NETFILTER_XT_MATCH_L2TP is not set CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m # CONFIG_NETFILTER_XT_MATCH_NFACCT is not set # CONFIG_NETFILTER_XT_MATCH_OSF is not set CONFIG_NETFILTER_XT_MATCH_OWNER=m # CONFIG_NETFILTER_XT_MATCH_POLICY is not set # CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set # CONFIG_NETFILTER_XT_MATCH_QUOTA is not set # CONFIG_NETFILTER_XT_MATCH_RATEEST is not set # CONFIG_NETFILTER_XT_MATCH_REALM is not set CONFIG_NETFILTER_XT_MATCH_RECENT=m # CONFIG_NETFILTER_XT_MATCH_SCTP is not set # CONFIG_NETFILTER_XT_MATCH_SOCKET is not set CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m # CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set CONFIG_NETFILTER_XT_MATCH_TIME=m # CONFIG_NETFILTER_XT_MATCH_U32 is not set CONFIG_IP_SET=m CONFIG_IP_SET_MAX=256 CONFIG_IP_SET_BITMAP_IP=m CONFIG_IP_SET_BITMAP_IPMAC=m CONFIG_IP_SET_BITMAP_PORT=m CONFIG_IP_SET_HASH_IP=m # CONFIG_IP_SET_HASH_IPMARK is not set CONFIG_IP_SET_HASH_IPPORT=m CONFIG_IP_SET_HASH_IPPORTIP=m CONFIG_IP_SET_HASH_IPPORTNET=m # CONFIG_IP_SET_HASH_MAC is not set # CONFIG_IP_SET_HASH_NETPORTNET is not set CONFIG_IP_SET_HASH_NET=m # CONFIG_IP_SET_HASH_NETNET is not set CONFIG_IP_SET_HASH_NETPORT=m CONFIG_IP_SET_HASH_NETIFACE=m CONFIG_IP_SET_LIST_SET=m # CONFIG_IP_VS is not set

# # IP: Netfilter Configuration # CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y # CONFIG_NF_LOG_ARP is not set CONFIG_NF_LOG_IPV4=m CONFIG_NF_REJECT_IPV4=m CONFIG_NF_NAT_IPV4=m CONFIG_NF_NAT_MASQUERADE_IPV4=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_IP_NF_IPTABLES=m # CONFIG_IP_NF_MATCH_AH is not set # CONFIG_IP_NF_MATCH_ECN is not set CONFIG_IP_NF_MATCH_RPFILTER=m # CONFIG_IP_NF_MATCH_TTL is not set CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m # CONFIG_IP_NF_TARGET_SYNPROXY is not set CONFIG_IP_NF_NAT=m CONFIG_IP_NF_TARGET_MASQUERADE=m # CONFIG_IP_NF_TARGET_NETMAP is not set CONFIG_IP_NF_TARGET_REDIRECT=m # CONFIG_NF_NAT_IPSEC is not set CONFIG_NF_NAT_PT=m CONFIG_NF_NAT_RTSP=m CONFIG_IP_NF_MANGLE=m # CONFIG_IP_NF_TARGET_CLUSTERIP is not set # CONFIG_IP_NF_TARGET_ECN is not set # CONFIG_IP_NF_TARGET_TTL is not set CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m # CONFIG_IP_NF_ARP_MANGLE is not set

# # IPv6: Netfilter Configuration # CONFIG_NF_DEFRAG_IPV6=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_NF_REJECT_IPV6=m CONFIG_NF_LOG_IPV6=m CONFIG_NF_NAT_IPV6=m # CONFIG_NF_NAT_MASQUERADE_IPV6 is not set CONFIG_IP6_NF_IPTABLES=m # CONFIG_IP6_NF_MATCH_AH is not set # CONFIG_IP6_NF_MATCH_EUI64 is not set CONFIG_IP6_NF_MATCH_FRAG=m # CONFIG_IP6_NF_MATCH_OPTS is not set # CONFIG_IP6_NF_MATCH_HL is not set # CONFIG_IP6_NF_MATCH_IPV6HEADER is not set # CONFIG_IP6_NF_MATCH_MH is not set CONFIG_IP6_NF_MATCH_RPFILTER=m # CONFIG_IP6_NF_MATCH_RT is not set # CONFIG_IP6_NF_TARGET_HL is not set CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m # CONFIG_IP6_NF_TARGET_SYNPROXY is not set CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_RAW=m # CONFIG_IP6_NF_NAT is not set CONFIG_BRIDGE_NF_EBTABLES=y CONFIG_BRIDGE_EBT_BROUTE=y CONFIG_BRIDGE_EBT_T_FILTER=y CONFIG_BRIDGE_EBT_T_NAT=y # CONFIG_BRIDGE_EBT_802_3 is not set # CONFIG_BRIDGE_EBT_AMONG is not set # CONFIG_BRIDGE_EBT_ARP is not set CONFIG_BRIDGE_EBT_IP=y CONFIG_BRIDGE_EBT_IP6=y # CONFIG_BRIDGE_EBT_LIMIT is not set CONFIG_BRIDGE_EBT_MARK=y # CONFIG_BRIDGE_EBT_PKTTYPE is not set # CONFIG_BRIDGE_EBT_STP is not set CONFIG_BRIDGE_EBT_VLAN=y CONFIG_BRIDGE_EBT_TIME=y CONFIG_BRIDGE_EBT_SKBVLAN=y # CONFIG_BRIDGE_EBT_ARPREPLY is not set # CONFIG_BRIDGE_EBT_DNAT is not set CONFIG_BRIDGE_EBT_MARK_T=y # CONFIG_BRIDGE_EBT_REDIRECT is not set # CONFIG_BRIDGE_EBT_SNAT is not set CONFIG_BRIDGE_EBT_FTOS_T=y CONFIG_BRIDGE_EBT_SKIPLOG_T=y CONFIG_BRIDGE_EBT_WMM_MARK=y # CONFIG_BRIDGE_EBT_LOG is not set # CONFIG_BRIDGE_EBT_NFLOG is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set # CONFIG_RDS is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set CONFIG_L2TP=y # CONFIG_L2TP_DEBUGFS is not set # CONFIG_L2TP_V3 is not set CONFIG_STP=y CONFIG_BRIDGE=y CONFIG_BRIDGE_IGMP_SNOOPING=y # CONFIG_BRIDGE_VLAN_FILTERING is not set # CONFIG_BCM_VLAN_AGGREGATION is not set CONFIG_HAVE_NET_DSA=y CONFIG_VLAN_8021Q=y # CONFIG_VLAN_8021Q_GVRP is not set # CONFIG_VLAN_8021Q_MVRP is not set # CONFIG_DECNET is not set CONFIG_LLC=y # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_PHONET is not set # CONFIG_6LOWPAN is not set # CONFIG_MHI is not set # CONFIG_IEEE802154 is not set CONFIG_NET_SCHED=y

# # Queueing/Scheduling # CONFIG_NET_SCH_CBQ=y CONFIG_NET_SCH_HTB=y CONFIG_NET_SCH_HFSC=y CONFIG_NET_SCH_PRIO=y # CONFIG_NET_SCH_MULTIQ is not set # CONFIG_NET_SCH_RED is not set # CONFIG_NET_SCH_SFB is not set CONFIG_NET_SCH_SFQ=y # CONFIG_NET_SCH_TEQL is not set CONFIG_NET_SCH_TBF=y # CONFIG_NET_SCH_GRED is not set CONFIG_NET_SCH_DSMARK=y # CONFIG_NET_SCH_NETEM is not set # CONFIG_NET_SCH_DRR is not set # CONFIG_NET_SCH_MQPRIO is not set # CONFIG_NET_SCH_CHOKE is not set # CONFIG_NET_SCH_QFQ is not set # CONFIG_NET_SCH_CODEL is not set # CONFIG_NET_SCH_FQ_CODEL is not set # CONFIG_NET_SCH_FQ is not set # CONFIG_NET_SCH_HHF is not set # CONFIG_NET_SCH_PIE is not set CONFIG_NET_SCH_INGRESS=y # CONFIG_NET_SCH_PLUG is not set

# # Classification # CONFIG_NET_CLS=y # CONFIG_NET_CLS_BASIC is not set CONFIG_NET_CLS_TCINDEX=y CONFIG_NET_CLS_ROUTE4=y CONFIG_NET_CLS_FW=y CONFIG_NET_CLS_U32=y # CONFIG_CLS_U32_PERF is not set # CONFIG_CLS_U32_MARK is not set # CONFIG_NET_CLS_RSVP is not set # CONFIG_NET_CLS_RSVP6 is not set # CONFIG_NET_CLS_FLOW is not set # CONFIG_NET_CLS_BPF is not set # CONFIG_NET_EMATCH is not set CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=y CONFIG_NET_ACT_GACT=y # CONFIG_GACT_PROB is not set CONFIG_NET_ACT_MIRRED=y # CONFIG_NET_ACT_IPT is not set # CONFIG_NET_ACT_NAT is not set # CONFIG_NET_ACT_PEDIT is not set # CONFIG_NET_ACT_SIMP is not set # CONFIG_NET_ACT_SKBEDIT is not set # CONFIG_NET_ACT_CSUM is not set # CONFIG_NET_ACT_VLAN is not set # CONFIG_NET_ACT_BPF is not set # CONFIG_NET_ACT_CONNMARK is not set CONFIG_NET_CLS_IND=y CONFIG_NET_SCH_FIFO=y # CONFIG_DCB is not set CONFIG_DNS_RESOLVER=m # CONFIG_BATMAN_ADV is not set # CONFIG_OPENVSWITCH is not set # CONFIG_VSOCKETS is not set # CONFIG_NETLINK_MMAP is not set # CONFIG_NETLINK_DIAG is not set # CONFIG_MPLS is not set # CONFIG_HSR is not set # CONFIG_NET_SWITCHDEV is not set CONFIG_RPS=y CONFIG_RFS_ACCEL=y CONFIG_XPS=y CONFIG_NET_RX_BUSY_POLL=y CONFIG_BQL=y # CONFIG_BPF_JIT is not set CONFIG_NET_FLOW_LIMIT=y

# # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set CONFIG_BT=m CONFIG_BT_BREDR=y CONFIG_BT_RFCOMM=m CONFIG_BT_RFCOMM_TTY=y # CONFIG_BT_BNEP is not set CONFIG_BT_LE=y # CONFIG_BT_SELFTEST is not set CONFIG_BT_DEBUGFS=y

# # Bluetooth device drivers # CONFIG_BT_INTEL=m CONFIG_BT_BCM=m CONFIG_BT_HCIBTUSB=m CONFIG_BT_HCIBTUSB_BCM=y CONFIG_BT_HCIUART=m # CONFIG_BT_HCIUART_H4 is not set # CONFIG_BT_HCIUART_BCSP is not set # CONFIG_BT_HCIUART_ATH3K is not set # CONFIG_BT_HCIUART_LL is not set # CONFIG_BT_HCIUART_3WIRE is not set # CONFIG_BT_HCIUART_INTEL is not set # CONFIG_BT_HCIUART_BCM is not set # CONFIG_BT_HCIBCM203X is not set # CONFIG_BT_HCIBPA10X is not set # CONFIG_BT_HCIBFUSB is not set # CONFIG_BT_HCIVHCI is not set # CONFIG_BT_MRVL is not set # CONFIG_BT_ATH3K is not set # CONFIG_AF_RXRPC is not set CONFIG_FIB_RULES=y # CONFIG_WIRELESS is not set # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # CONFIG_CAIF is not set # CONFIG_CEPH_LIB is not set # CONFIG_NFC is not set CONFIG_HAVE_BPF_JIT=y

# # Device Drivers #

# # Generic Driver Options # CONFIG_UEVENT_HELPER=y CONFIG_UEVENT_HELPER_PATH=“/sbin/hotplug” CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=m # CONFIG_FIRMWARE_IN_KERNEL is not set CONFIG_EXTRA_FIRMWARE=“” # CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set # CONFIG_ALLOW_DEV_COREDUMP is not set # CONFIG_DEBUG_DRIVER is not set # CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_GENERIC_CPU_DEVICES is not set # CONFIG_DMA_SHARED_BUFFER is not set

# # Bus devices # # CONFIG_BRCMSTB_GISB_ARB is not set # CONFIG_VEXPRESS_CONFIG is not set # CONFIG_CONNECTOR is not set CONFIG_MTD=y # CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set # CONFIG_MTD_CMDLINE_PARTS is not set # CONFIG_MTD_AFS_PARTS is not set CONFIG_MTD_OF_PARTS=y # CONFIG_MTD_AR7_PARTS is not set

# # User Modules And Translation Layers # CONFIG_MTD_BLKDEVS=y CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set # CONFIG_NFTL is not set # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set # CONFIG_SM_FTL is not set # CONFIG_MTD_OOPS is not set # CONFIG_MTD_SWAP is not set CONFIG_MTD_PARTITIONED_MASTER=y

# # RAM/ROM/Flash chip drivers # # CONFIG_MTD_CFI is not set # CONFIG_MTD_JEDECPROBE is not set CONFIG_MTD_MAP_BANK_WIDTH_1=y CONFIG_MTD_MAP_BANK_WIDTH_2=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set # CONFIG_MTD_MAP_BANK_WIDTH_16 is not set # CONFIG_MTD_MAP_BANK_WIDTH_32 is not set CONFIG_MTD_CFI_I1=y CONFIG_MTD_CFI_I2=y # CONFIG_MTD_CFI_I4 is not set # CONFIG_MTD_CFI_I8 is not set # CONFIG_MTD_RAM is not set CONFIG_MTD_ROM=y # CONFIG_MTD_ABSENT is not set

# # Mapping drivers for chip access # CONFIG_MTD_COMPLEX_MAPPINGS=y # CONFIG_MTD_PHYSMAP is not set # CONFIG_MTD_PHYSMAP_OF is not set CONFIG_MTD_BCM963XX=y # CONFIG_MTD_PCI is not set # CONFIG_MTD_GPIO_ADDR is not set # CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # CONFIG_MTD_LATCH_ADDR is not set

# # Self-contained MTD device drivers # # CONFIG_MTD_PMC551 is not set # CONFIG_MTD_DATAFLASH is not set # CONFIG_MTD_SST25L is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set # CONFIG_MTD_BLOCK2MTD is not set

# # Disk-On-Chip Device Drivers # # CONFIG_MTD_DOCG3 is not set CONFIG_MTD_NAND_ECC=y # CONFIG_MTD_NAND_ECC_SMC is not set CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_ECC_BCH is not set # CONFIG_MTD_SM_COMMON is not set # CONFIG_MTD_NAND_DENALI is not set # CONFIG_MTD_NAND_GPIO is not set # CONFIG_MTD_NAND_OMAP_BCH_BUILD is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_RICOH is not set # CONFIG_MTD_NAND_DISKONCHIP is not set # CONFIG_MTD_NAND_DOCG4 is not set # CONFIG_MTD_NAND_CAFE is not set # CONFIG_MTD_NAND_NANDSIM is not set CONFIG_MTD_NAND_BRCMNAND=y # CONFIG_MTD_NAND_PLATFORM is not set # CONFIG_MTD_NAND_HISI504 is not set # CONFIG_MTD_ONENAND is not set

# # LPDDR & LPDDR2 PCM memory drivers # # CONFIG_MTD_LPDDR is not set # CONFIG_MTD_LPDDR2_NVM is not set # CONFIG_MTD_SPI_NOR is not set CONFIG_MTD_UBI=y CONFIG_MTD_UBI_WL_THRESHOLD=4096 CONFIG_MTD_UBI_BEB_LIMIT=20 # CONFIG_MTD_UBI_FASTMAP is not set CONFIG_MTD_UBI_GLUEBI=y CONFIG_MTD_UBI_BLOCK=y # CONFIG_MTD_BRCMNAND is not set CONFIG_DTC=y CONFIG_OF=y

# # Device Tree and Open Firmware support # # CONFIG_OF_UNITTEST is not set CONFIG_OF_FLATTREE=y CONFIG_OF_EARLY_FLATTREE=y CONFIG_OF_ADDRESS=y CONFIG_OF_ADDRESS_PCI=y CONFIG_OF_IRQ=y CONFIG_OF_NET=y CONFIG_OF_MDIO=m CONFIG_OF_PCI=y CONFIG_OF_PCI_IRQ=y CONFIG_OF_MTD=y CONFIG_OF_RESERVED_MEM=y # CONFIG_OF_OVERLAY is not set CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_NULL_BLK is not set # CONFIG_BLK_DEV_PCIESSD_MTIP32XX is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_UMEM is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_LOOP_MIN_COUNT=4 # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_DRBD is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_NVME is not set # CONFIG_BLK_DEV_SX8 is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=1 CONFIG_BLK_DEV_RAM_SIZE=16384 # CONFIG_BLK_DEV_PMEM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # CONFIG_MG_DISK is not set # CONFIG_BLK_DEV_RBD is not set # CONFIG_BLK_DEV_RSXX is not set

# # Misc devices # # CONFIG_AD525X_DPOT is not set # CONFIG_DUMMY_IRQ is not set # CONFIG_PHANTOM is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set # CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set # CONFIG_APDS9802ALS is not set # CONFIG_ISL29003 is not set # CONFIG_ISL29020 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_SENSORS_BH1780 is not set # CONFIG_SENSORS_BH1770 is not set # CONFIG_SENSORS_APDS990X is not set # CONFIG_HMC6352 is not set # CONFIG_DS1682 is not set # CONFIG_TI_DAC7512 is not set # CONFIG_BMP085_I2C is not set # CONFIG_BMP085_SPI is not set # CONFIG_USB_SWITCH_FSA9480 is not set # CONFIG_LATTICE_ECP3_CONFIG is not set # CONFIG_SRAM is not set # CONFIG_C2PORT is not set

# # EEPROM support # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_AT25 is not set # CONFIG_EEPROM_LEGACY is not set # CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_EEPROM_93XX46 is not set # CONFIG_CB710_CORE is not set

# # Texas Instruments shared transport line discipline # # CONFIG_TI_ST is not set

# # Altera FPGA firmware download module # # CONFIG_ALTERA_STAPL is not set

# # Intel MIC Bus Driver #

# # Intel MIC Host Driver #

# # Intel MIC Card Driver # # CONFIG_ECHO is not set # CONFIG_CXL_BASE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set

# # SCSI device support # CONFIG_SCSI_MOD=y # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_DMA=y # CONFIG_SCSI_NETLINK is not set # CONFIG_SCSI_MQ_DEFAULT is not set CONFIG_SCSI_PROC_FS=y

# # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y CONFIG_BLK_DEV_SR_VENDOR=y # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set # CONFIG_SCSI_SCAN_ASYNC is not set

# # SCSI Transports # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set # CONFIG_SCSI_DH is not set # CONFIG_SCSI_OSD_INITIATOR is not set # CONFIG_ATA is not set # CONFIG_MD is not set # CONFIG_TARGET_CORE is not set # CONFIG_FUSION is not set

# # IEEE 1394 (FireWire) support # # CONFIG_FIREWIRE is not set # CONFIG_FIREWIRE_NOSY is not set CONFIG_NETDEVICES=y CONFIG_MII=m CONFIG_NET_CORE=y # CONFIG_BONDING is not set CONFIG_DUMMY=m # CONFIG_EQUALIZER is not set # CONFIG_NET_FC is not set CONFIG_IFB=y # CONFIG_NET_TEAM is not set CONFIG_MACVLAN=y # CONFIG_MACVTAP is not set # CONFIG_IPVLAN is not set # CONFIG_VXLAN is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set CONFIG_TUN=y # CONFIG_VETH is not set # CONFIG_NLMON is not set # CONFIG_ARCNET is not set

# # CAIF transport drivers #

# # Distributed Switch Architecture drivers # # CONFIG_NET_DSA_MV88E6XXX is not set # CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set # CONFIG_ETHERNET is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set CONFIG_PHYLIB=m

# # MII PHY device drivers # # CONFIG_AT803X_PHY is not set # CONFIG_AMD_PHY is not set # CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set # CONFIG_CICADA_PHY is not set # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_BCM7XXX_PHY is not set # CONFIG_BCM87XX_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set # CONFIG_MICREL_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set # CONFIG_MDIO_BUS_MUX_GPIO is not set # CONFIG_MDIO_BUS_MUX_MMIOREG is not set # CONFIG_MDIO_BCM_UNIMAC is not set # CONFIG_MICREL_KS8995MA is not set CONFIG_PPP=y # CONFIG_PPP_BSDCOMP is not set # CONFIG_PPP_DEFLATE is not set # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y CONFIG_PPP_MULTILINK=y CONFIG_PPPOE=y # CONFIG_PPTP is not set # CONFIG_PPPOL2TP is not set # CONFIG_PPP_ASYNC is not set # CONFIG_PPP_SYNC_TTY is not set # CONFIG_SLIP is not set CONFIG_SLHC=y CONFIG_USB_NET_DRIVERS=y # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_RTL8152 is not set CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m CONFIG_USB_NET_AX88179_178A=m CONFIG_USB_NET_CDCETHER=m CONFIG_USB_NET_CDC_EEM=m CONFIG_USB_NET_CDC_NCM=m # CONFIG_USB_NET_HUAWEI_CDC_NCM is not set CONFIG_USB_NET_CDC_MBIM=m # CONFIG_USB_NET_DM9601 is not set # CONFIG_USB_NET_SR9700 is not set # CONFIG_USB_NET_SR9800 is not set # CONFIG_USB_NET_SMSC75XX is not set # CONFIG_USB_NET_SMSC95XX is not set # CONFIG_USB_NET_GL620A is not set # CONFIG_USB_NET_NET1080 is not set # CONFIG_USB_NET_PLUSB is not set # CONFIG_USB_NET_MCS7830 is not set CONFIG_USB_NET_RNDIS_HOST=m # CONFIG_USB_NET_CDC_SUBSET is not set # CONFIG_USB_NET_ZAURUS is not set # CONFIG_USB_NET_CX82310_ETH is not set CONFIG_USB_NET_KALMIA=m CONFIG_USB_NET_QMI_WWAN=m # CONFIG_USB_NET_INT51X1 is not set # CONFIG_USB_IPHETH is not set # CONFIG_USB_SIERRA_NET is not set CONFIG_USB_VL600=m # CONFIG_WLAN is not set

# # Enable WiMAX (Networking options) to see the WiMAX drivers # # CONFIG_WAN is not set # CONFIG_VMXNET3 is not set # CONFIG_ISDN is not set

# # Input device support # # CONFIG_INPUT is not set

# # Hardware I/O ports # # CONFIG_SERIO is not set # CONFIG_GAMEPORT is not set

# # Character devices # CONFIG_TTY=y # CONFIG_VT is not set CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=2 # CONFIG_SERIAL_NONSTANDARD is not set # CONFIG_NOZOMI is not set # CONFIG_N_GSM is not set # CONFIG_TRACE_SINK is not set CONFIG_DEVMEM=y # CONFIG_DEVKMEM is not set

# # Serial drivers # # CONFIG_SERIAL_8250 is not set

# # Non-8250 serial port support # # CONFIG_SERIAL_EARLYCON_ARM_SEMIHOST is not set CONFIG_SERIAL_MAX3100=m # CONFIG_SERIAL_MAX310X is not set CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set # CONFIG_SERIAL_SCCNXP is not set # CONFIG_SERIAL_SC16IS7XX is not set # CONFIG_SERIAL_BCM63XX is not set # CONFIG_SERIAL_ALTERA_JTAGUART is not set # CONFIG_SERIAL_ALTERA_UART is not set # CONFIG_SERIAL_IFX6X60 is not set # CONFIG_SERIAL_XILINX_PS_UART is not set # CONFIG_SERIAL_ARC is not set # CONFIG_SERIAL_RP2 is not set # CONFIG_SERIAL_FSL_LPUART is not set # CONFIG_SERIAL_CONEXANT_DIGICOLOR is not set # CONFIG_SERIAL_ST_ASC is not set # CONFIG_TTY_PRINTK is not set # CONFIG_HVC_DCC is not set # CONFIG_IPMI_HANDLER is not set CONFIG_HW_RANDOM=y # CONFIG_HW_RANDOM_TIMERIOMEM is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y # CONFIG_XILLYBUS is not set

# # I2C support # CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_COMPAT=y CONFIG_I2C_CHARDEV=y # CONFIG_I2C_MUX is not set CONFIG_I2C_HELPER_AUTO=y

# # I2C Algorithms # CONFIG_I2C_ALGOBIT=m # CONFIG_I2C_ALGOPCF is not set # CONFIG_I2C_ALGOPCA is not set

# # I2C Hardware Bus support #

# # PC SMBus host controller drivers # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set # CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set

# # I2C system bus drivers (mostly embedded / system-on-chip) # # CONFIG_I2C_CBUS_GPIO is not set # CONFIG_I2C_DESIGNWARE_PLATFORM is not set # CONFIG_I2C_DESIGNWARE_PCI is not set CONFIG_I2C_GPIO=m # CONFIG_I2C_OCORES is not set # CONFIG_I2C_PCA_PLATFORM is not set # CONFIG_I2C_PXA_PCI is not set # CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_XILINX is not set

# # External I2C/SMBus adapter drivers # # CONFIG_I2C_DIOLAN_U2C is not set # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_ROBOTFUZZ_OSIF is not set # CONFIG_I2C_TAOS_EVM is not set # CONFIG_I2C_TINY_USB is not set

# # Other I2C/SMBus bus drivers # CONFIG_I2C_GPIO_CUSTOM=m # CONFIG_I2C_STUB is not set # CONFIG_I2C_SLAVE is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set CONFIG_SPI=y # CONFIG_SPI_DEBUG is not set CONFIG_SPI_MASTER=y

# # SPI Master Controller Drivers # # CONFIG_SPI_ALTERA is not set # CONFIG_SPI_BITBANG is not set # CONFIG_SPI_CADENCE is not set # CONFIG_SPI_GPIO is not set # CONFIG_SPI_FSL_SPI is not set # CONFIG_SPI_OC_TINY is not set # CONFIG_SPI_PXA2XX is not set # CONFIG_SPI_PXA2XX_PCI is not set # CONFIG_SPI_ROCKCHIP is not set # CONFIG_SPI_SC18IS602 is not set # CONFIG_SPI_XCOMM is not set # CONFIG_SPI_XILINX is not set # CONFIG_SPI_DESIGNWARE is not set

# # SPI Protocol Masters # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set # CONFIG_SPMI is not set # CONFIG_HSI is not set

# # PPS support # # CONFIG_PPS is not set

# # PPS generators support #

# # PTP clock support # # CONFIG_PTP_1588_CLOCK is not set

# # Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks. # CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y CONFIG_GPIOLIB=y CONFIG_GPIO_DEVRES=y CONFIG_OF_GPIO=y CONFIG_DEBUG_GPIO=y CONFIG_GPIO_SYSFS=y

# # Memory mapped GPIO drivers # # CONFIG_GPIO_74XX_MMIO is not set # CONFIG_GPIO_ALTERA is not set # CONFIG_GPIO_DWAPB is not set # CONFIG_GPIO_EM is not set # CONFIG_GPIO_GENERIC_PLATFORM is not set # CONFIG_GPIO_GRGPIO is not set # CONFIG_GPIO_SCH311X is not set # CONFIG_GPIO_VX855 is not set # CONFIG_GPIO_ZEVIO is not set

# # I2C GPIO expanders # # CONFIG_GPIO_ADP5588 is not set # CONFIG_GPIO_ADNP is not set # CONFIG_GPIO_MAX7300 is not set # CONFIG_GPIO_MAX732X is not set # CONFIG_GPIO_PCA953X is not set # CONFIG_GPIO_PCF857X is not set # CONFIG_GPIO_SX150X is not set

# # MFD GPIO expanders #

# # PCI GPIO expanders # # CONFIG_GPIO_AMD8111 is not set # CONFIG_GPIO_BT8XX is not set # CONFIG_GPIO_ML_IOH is not set # CONFIG_GPIO_RDC321X is not set

# # SPI GPIO expanders # # CONFIG_GPIO_74X164 is not set # CONFIG_GPIO_MAX7301 is not set # CONFIG_GPIO_MCP23S08 is not set # CONFIG_GPIO_MC33880 is not set

# # USB GPIO expanders # # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_POWER_AVS is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set CONFIG_WATCHDOG=y CONFIG_WATCHDOG_CORE=y # CONFIG_WATCHDOG_NOWAYOUT is not set

# # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set # CONFIG_GPIO_WATCHDOG is not set # CONFIG_XILINX_WATCHDOG is not set CONFIG_BCM96XXX_WDT=y # CONFIG_CADENCE_WATCHDOG is not set # CONFIG_DW_WATCHDOG is not set # CONFIG_MAX63XX_WATCHDOG is not set # CONFIG_ALIM7101_WDT is not set # CONFIG_I6300ESB_WDT is not set # CONFIG_MEN_A21_WDT is not set

# # PCI-based Watchdog Cards # # CONFIG_PCIPCWATCHDOG is not set # CONFIG_WDTPCI is not set

# # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set CONFIG_SSB_POSSIBLE=y

# # Sonics Silicon Backplane # # CONFIG_SSB is not set CONFIG_BCMA_POSSIBLE=y

# # Broadcom specific AMBA # # CONFIG_BCMA is not set

# # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_AS3711 is not set # CONFIG_MFD_AS3722 is not set # CONFIG_PMIC_ADP5520 is not set # CONFIG_MFD_AAT2870_CORE is not set # CONFIG_MFD_ATMEL_HLCDC is not set # CONFIG_MFD_BCM590XX is not set # CONFIG_MFD_AXP20X is not set # CONFIG_MFD_CROS_EC is not set # CONFIG_MFD_ASIC3 is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_DA9052_SPI is not set # CONFIG_MFD_DA9052_I2C is not set # CONFIG_MFD_DA9055 is not set # CONFIG_MFD_DA9063 is not set # CONFIG_MFD_DA9150 is not set # CONFIG_MFD_DLN2 is not set # CONFIG_MFD_MC13XXX_SPI is not set # CONFIG_MFD_MC13XXX_I2C is not set # CONFIG_MFD_HI6421_PMIC is not set # CONFIG_HTC_EGPIO is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_HTC_I2CPLD is not set # CONFIG_LPC_ICH is not set # CONFIG_LPC_SCH is not set # CONFIG_INTEL_SOC_PMIC is not set # CONFIG_MFD_JANZ_CMODIO is not set # CONFIG_MFD_KEMPLD is not set # CONFIG_MFD_88PM800 is not set # CONFIG_MFD_88PM805 is not set # CONFIG_MFD_88PM860X is not set # CONFIG_MFD_MAX14577 is not set # CONFIG_MFD_MAX77686 is not set # CONFIG_MFD_MAX77693 is not set # CONFIG_MFD_MAX77843 is not set # CONFIG_MFD_MAX8907 is not set # CONFIG_MFD_MAX8925 is not set # CONFIG_MFD_MAX8997 is not set # CONFIG_MFD_MAX8998 is not set # CONFIG_MFD_MT6397 is not set # CONFIG_MFD_MENF21BMC is not set # CONFIG_EZX_PCAP is not set # CONFIG_MFD_VIPERBOARD is not set # CONFIG_MFD_RETU is not set # CONFIG_MFD_PCF50633 is not set # CONFIG_MFD_PM8921_CORE is not set # CONFIG_MFD_RDC321X is not set # CONFIG_MFD_RTSX_PCI is not set # CONFIG_MFD_RT5033 is not set # CONFIG_MFD_RTSX_USB is not set # CONFIG_MFD_RC5T583 is not set # CONFIG_MFD_RK808 is not set # CONFIG_MFD_RN5T618 is not set # CONFIG_MFD_SEC_CORE is not set # CONFIG_MFD_SI476X_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_MFD_SKY81452 is not set # CONFIG_MFD_SMSC is not set # CONFIG_ABX500_CORE is not set # CONFIG_MFD_STMPE is not set # CONFIG_MFD_SYSCON is not set # CONFIG_MFD_TI_AM335X_TSCADC is not set # CONFIG_MFD_LP3943 is not set # CONFIG_MFD_LP8788 is not set # CONFIG_MFD_PALMAS is not set # CONFIG_TPS6105X is not set # CONFIG_TPS65010 is not set # CONFIG_TPS6507X is not set # CONFIG_MFD_TPS65090 is not set # CONFIG_MFD_TPS65217 is not set # CONFIG_MFD_TPS65218 is not set # CONFIG_MFD_TPS6586X is not set # CONFIG_MFD_TPS65910 is not set # CONFIG_MFD_TPS65912 is not set # CONFIG_MFD_TPS65912_I2C is not set # CONFIG_MFD_TPS65912_SPI is not set # CONFIG_MFD_TPS80031 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_TWL6040_CORE is not set # CONFIG_MFD_WL1273_CORE is not set # CONFIG_MFD_LM3533 is not set # CONFIG_MFD_TC3589X is not set # CONFIG_MFD_TMIO is not set # CONFIG_MFD_T7L66XB is not set # CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_MFD_VX855 is not set # CONFIG_MFD_ARIZONA_I2C is not set # CONFIG_MFD_ARIZONA_SPI is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM831X_I2C is not set # CONFIG_MFD_WM831X_SPI is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_WM8994 is not set # CONFIG_REGULATOR is not set # CONFIG_MEDIA_SUPPORT is not set

# # Graphics support # # CONFIG_VGA_ARB is not set

# # Direct Rendering Manager # # CONFIG_DRM is not set

# # Frame buffer Devices # # CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # CONFIG_VGASTATE is not set CONFIG_SOUND=m CONFIG_SOUND_OSS_CORE=y CONFIG_SOUND_OSS_CORE_PRECLAIM=y CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_HWDEP=m CONFIG_SND_RAWMIDI=m CONFIG_SND_SEQUENCER=m CONFIG_SND_SEQ_DUMMY=m CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m # CONFIG_SND_PCM_OSS_PLUGINS is not set CONFIG_SND_SEQUENCER_OSS=y # CONFIG_SND_DYNAMIC_MINORS is not set # CONFIG_SND_SUPPORT_OLD_API is not set # CONFIG_SND_VERBOSE_PROCFS is not set # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set CONFIG_SND_RAWMIDI_SEQ=m # CONFIG_SND_OPL3_LIB_SEQ is not set # CONFIG_SND_OPL4_LIB_SEQ is not set # CONFIG_SND_SBAWE_SEQ is not set # CONFIG_SND_EMU10K1_SEQ is not set CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set # CONFIG_SND_ALOOP is not set CONFIG_SND_VIRMIDI=m # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set # CONFIG_SND_PCI is not set

# # HD-Audio # # CONFIG_SND_ARM is not set # CONFIG_SND_SPI is not set CONFIG_SND_USB=y CONFIG_SND_USB_AUDIO=m # CONFIG_SND_USB_UA101 is not set # CONFIG_SND_USB_CAIAQ is not set # CONFIG_SND_USB_6FIRE is not set # CONFIG_SND_USB_HIFACE is not set # CONFIG_SND_BCD2000 is not set # CONFIG_SND_USB_POD is not set # CONFIG_SND_USB_PODHD is not set # CONFIG_SND_USB_TONEPORT is not set # CONFIG_SND_USB_VARIAX is not set # CONFIG_SND_SOC is not set # CONFIG_SOUND_PRIME is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_SUPPORT=y CONFIG_USB_COMMON=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB=y # CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set

# # Miscellaneous USB options # # CONFIG_USB_DEFAULT_PERSIST is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set # CONFIG_USB_OTG_FSM is not set # CONFIG_USB_MON is not set # CONFIG_USB_WUSB_CBAF is not set

# # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_XHCI_HCD=m CONFIG_USB_XHCI_PCI=m CONFIG_USB_XHCI_PLATFORM=m CONFIG_USB_EHCI_HCD=m # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_EHCI_TT_NEWSCHED is not set CONFIG_USB_EHCI_PCI=m CONFIG_USB_EHCI_HCD_PLATFORM=m # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1362_HCD is not set # CONFIG_USB_FUSBH200_HCD is not set # CONFIG_USB_FOTG210_HCD is not set # CONFIG_USB_MAX3421_HCD is not set CONFIG_USB_OHCI_HCD=m CONFIG_USB_OHCI_HCD_PCI=m CONFIG_USB_OHCI_HCD_PLATFORM=m # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_HCD_TEST_MODE is not set

# # USB Device Class drivers # CONFIG_USB_ACM=y CONFIG_USB_PRINTER=m CONFIG_USB_WDM=m # CONFIG_USB_TMC is not set

# # NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may #

# # also be needed; see USB_STORAGE Help for more info # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_REALTEK is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_STORAGE_CYPRESS_ATACB is not set # CONFIG_USB_STORAGE_ENE_UB6250 is not set # CONFIG_USB_UAS is not set

# # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # CONFIG_USBIP_CORE is not set # CONFIG_USB_MUSB_HDRC is not set # CONFIG_USB_DWC3 is not set # CONFIG_USB_DWC2 is not set # CONFIG_USB_CHIPIDEA is not set # CONFIG_USB_ISP1760 is not set

# # USB port drivers # CONFIG_USB_SERIAL=y CONFIG_USB_SERIAL_CONSOLE=y CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_SIMPLE is not set # CONFIG_USB_SERIAL_AIRCABLE is not set # CONFIG_USB_SERIAL_ARK3116 is not set # CONFIG_USB_SERIAL_BELKIN is not set # CONFIG_USB_SERIAL_CH341 is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set CONFIG_USB_SERIAL_CP210X=y # CONFIG_USB_SERIAL_CYPRESS_M8 is not set # CONFIG_USB_SERIAL_EMPEG is not set CONFIG_USB_SERIAL_FTDI_SIO=y # CONFIG_USB_SERIAL_VISOR is not set # CONFIG_USB_SERIAL_IPAQ is not set # CONFIG_USB_SERIAL_IR is not set # CONFIG_USB_SERIAL_EDGEPORT is not set # CONFIG_USB_SERIAL_EDGEPORT_TI is not set # CONFIG_USB_SERIAL_F81232 is not set # CONFIG_USB_SERIAL_GARMIN is not set # CONFIG_USB_SERIAL_IPW is not set # CONFIG_USB_SERIAL_IUU is not set # CONFIG_USB_SERIAL_KEYSPAN_PDA is not set # CONFIG_USB_SERIAL_KEYSPAN is not set # CONFIG_USB_SERIAL_KLSI is not set # CONFIG_USB_SERIAL_KOBIL_SCT is not set # CONFIG_USB_SERIAL_MCT_U232 is not set # CONFIG_USB_SERIAL_METRO is not set # CONFIG_USB_SERIAL_MOS7720 is not set # CONFIG_USB_SERIAL_MOS7840 is not set # CONFIG_USB_SERIAL_MXUPORT is not set # CONFIG_USB_SERIAL_NAVMAN is not set CONFIG_USB_SERIAL_PL2303=y # CONFIG_USB_SERIAL_OTI6858 is not set CONFIG_USB_SERIAL_QCAUX=m CONFIG_USB_SERIAL_QUALCOMM=m # CONFIG_USB_SERIAL_SPCP8X5 is not set # CONFIG_USB_SERIAL_SAFE is not set # CONFIG_USB_SERIAL_SIERRAWIRELESS is not set # CONFIG_USB_SERIAL_SYMBOL is not set # CONFIG_USB_SERIAL_TI is not set # CONFIG_USB_SERIAL_CYBERJACK is not set # CONFIG_USB_SERIAL_XIRCOM is not set CONFIG_USB_SERIAL_WWAN=y CONFIG_USB_SERIAL_OPTION=y # CONFIG_USB_SERIAL_OMNINET is not set # CONFIG_USB_SERIAL_OPTICON is not set # CONFIG_USB_SERIAL_XSENS_MT is not set # CONFIG_USB_SERIAL_WISHBONE is not set # CONFIG_USB_SERIAL_SSU100 is not set # CONFIG_USB_SERIAL_QT2 is not set # CONFIG_USB_SERIAL_DEBUG is not set

# # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set # CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYPRESS_CY7C63 is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_FTDI_ELAN is not set # CONFIG_USB_APPLEDISPLAY is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_EHSET_TEST_FIXTURE is not set # CONFIG_USB_ISIGHTFW is not set # CONFIG_USB_YUREX is not set # CONFIG_USB_EZUSB_FX2 is not set # CONFIG_USB_HSIC_USB3503 is not set # CONFIG_USB_LINK_LAYER_TEST is not set # CONFIG_USB_CHAOSKEY is not set

# # USB Physical Layer drivers # # CONFIG_USB_PHY is not set # CONFIG_NOP_USB_XCEIV is not set # CONFIG_AM335X_PHY_USB is not set # CONFIG_USB_GPIO_VBUS is not set # CONFIG_USB_ISP1301 is not set # CONFIG_USB_ULPI is not set # CONFIG_USB_GADGET is not set # CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y # CONFIG_LEDS_CLASS_FLASH is not set

# # LED drivers # # CONFIG_LEDS_LM3530 is not set # CONFIG_LEDS_LM3642 is not set # CONFIG_LEDS_GPIO is not set # CONFIG_LEDS_LP3944 is not set # CONFIG_LEDS_LP5521 is not set # CONFIG_LEDS_LP5523 is not set # CONFIG_LEDS_LP5562 is not set # CONFIG_LEDS_LP8501 is not set # CONFIG_LEDS_LP8860 is not set # CONFIG_LEDS_PCA955X is not set # CONFIG_LEDS_PCA963X is not set # CONFIG_LEDS_DAC124S085 is not set # CONFIG_LEDS_BD2802 is not set # CONFIG_LEDS_LT3593 is not set # CONFIG_LEDS_TCA6507 is not set # CONFIG_LEDS_LM355x is not set

# # LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM) # # CONFIG_LEDS_BLINKM is not set # CONFIG_LEDS_PM8941_WLED is not set

# # LED Triggers # # CONFIG_LEDS_TRIGGERS is not set # CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set # CONFIG_EDAC is not set CONFIG_RTC_LIB=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set # CONFIG_VIRT_DRIVERS is not set

# # Virtio drivers # # CONFIG_VIRTIO_PCI is not set # CONFIG_VIRTIO_MMIO is not set

# # Microsoft Hyper-V guest support # # CONFIG_STAGING is not set # CONFIG_CHROME_PLATFORMS is not set CONFIG_IOPSYS_PSTORE=y CONFIG_CLKDEV_LOOKUP=y CONFIG_HAVE_MACH_CLKDEV=y

# # Hardware Spinlock drivers #

# # Clock Source drivers # # CONFIG_ATMEL_PIT is not set # CONFIG_SH_TIMER_CMT is not set # CONFIG_SH_TIMER_MTU2 is not set # CONFIG_SH_TIMER_TMU is not set # CONFIG_EM_TIMER_STI is not set # CONFIG_MAILBOX is not set # CONFIG_IOMMU_SUPPORT is not set

# # Remoteproc drivers # # CONFIG_STE_MODEM_RPROC is not set

# # Rpmsg drivers #

# # SOC (System On Chip) specific Drivers # # CONFIG_SOC_TI is not set # CONFIG_PM_DEVFREQ is not set # CONFIG_EXTCON is not set # CONFIG_MEMORY is not set # CONFIG_IIO is not set # CONFIG_VME_BUS is not set # CONFIG_PWM is not set CONFIG_IRQCHIP=y CONFIG_ARM_GIC=y # CONFIG_IPACK_BUS is not set # CONFIG_RESET_CONTROLLER is not set # CONFIG_FMC is not set

# # PHY Subsystem # # CONFIG_GENERIC_PHY is not set # CONFIG_BCM_KONA_USB2_PHY is not set # CONFIG_POWERCAP is not set # CONFIG_MCB is not set # CONFIG_THUNDERBOLT is not set

# # Android # # CONFIG_ANDROID is not set

# # Firmware Drivers # # CONFIG_FIRMWARE_MEMMAP is not set

# # File systems # CONFIG_DCACHE_WORD_ACCESS=y # CONFIG_EXT2_FS is not set # CONFIG_EXT3_FS is not set CONFIG_EXT4_FS=y CONFIG_EXT4_USE_FOR_EXT23=y CONFIG_EXT4_FS_POSIX_ACL=y CONFIG_EXT4_FS_SECURITY=y # CONFIG_EXT4_ENCRYPTION is not set # CONFIG_EXT4_DEBUG is not set CONFIG_JBD2=y # CONFIG_JBD2_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_BTRFS_FS is not set # CONFIG_NILFS2_FS is not set # CONFIG_F2FS_FS is not set CONFIG_FS_POSIX_ACL=y CONFIG_FILE_LOCKING=y CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set CONFIG_INOTIFY_USER=y # CONFIG_FANOTIFY is not set # CONFIG_QUOTA is not set # CONFIG_QUOTACTL is not set CONFIG_AUTOFS4_FS=y CONFIG_FUSE_FS=y # CONFIG_CUSE is not set CONFIG_OVERLAY_FS=y

# # Caches # # CONFIG_FSCACHE is not set

# # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=y CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_UDF_FS=y CONFIG_UDF_NLS=y

# # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y # CONFIG_MSDOS_FS is not set CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET=“iso8859-1” # CONFIG_NTFS_FS is not set

# # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_SYSCTL=y CONFIG_PROC_PAGE_MONITOR=y CONFIG_KERNFS=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_TMPFS_XATTR=y # CONFIG_HUGETLB_PAGE is not set # CONFIG_CONFIGFS_FS is not set CONFIG_MISC_FILESYSTEMS=y # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_ECRYPT_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y # CONFIG_JFFS2_FS_WBUF_VERIFY is not set CONFIG_JFFS2_SUMMARY=y CONFIG_JFFS2_FS_XATTR=y # CONFIG_JFFS2_FS_POSIX_ACL is not set CONFIG_JFFS2_FS_SECURITY=y CONFIG_JFFS2_COMPRESSION_OPTIONS=y CONFIG_JFFS2_ZLIB=y # CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_LZMA=y CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set # CONFIG_JFFS2_CMODE_NONE is not set CONFIG_JFFS2_CMODE_PRIORITY=y # CONFIG_JFFS2_CMODE_SIZE is not set # CONFIG_JFFS2_CMODE_FAVOURLZO is not set CONFIG_UBIFS_FS=y # CONFIG_UBIFS_FS_ADVANCED_COMPR is not set CONFIG_UBIFS_FS_LZO=y CONFIG_UBIFS_FS_ZLIB=y CONFIG_UBIFS_FS_LZMA=y # CONFIG_LOGFS is not set # CONFIG_CRAMFS is not set CONFIG_SQUASHFS=y CONFIG_SQUASHFS_FILE_CACHE=y # CONFIG_SQUASHFS_FILE_DIRECT is not set CONFIG_SQUASHFS_DECOMP_SINGLE=y # CONFIG_SQUASHFS_DECOMP_MULTI is not set # CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU is not set # CONFIG_SQUASHFS_XATTR is not set CONFIG_SQUASHFS_ZLIB=y # CONFIG_SQUASHFS_LZ4 is not set # CONFIG_SQUASHFS_LZO is not set CONFIG_SQUASHFS_XZ=y # CONFIG_SQUASHFS_4K_DEVBLK_SIZE is not set CONFIG_SQUASHFS_EMBEDDED=y CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=1 # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_QNX6FS_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_PSTORE=y CONFIG_PSTORE_CONSOLE=y # CONFIG_PSTORE_PMSG is not set CONFIG_PSTORE_RAM=y # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V2=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set # CONFIG_NFS_SWAP is not set # CONFIG_NFSD is not set CONFIG_GRACE_PERIOD=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_SUNRPC_DEBUG is not set # CONFIG_CEPH_FS is not set CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set # CONFIG_CIFS_WEAK_PW_HASH is not set CONFIG_CIFS_UPCALL=y # CONFIG_CIFS_XATTR is not set CONFIG_CIFS_DEBUG=y # CONFIG_CIFS_DEBUG2 is not set CONFIG_CIFS_DFS_UPCALL=y # CONFIG_CIFS_SMB2 is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set CONFIG_NLS=y CONFIG_NLS_DEFAULT=“iso8859-1” CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set # CONFIG_NLS_ASCII is not set CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_MAC_ROMAN is not set # CONFIG_NLS_MAC_CELTIC is not set # CONFIG_NLS_MAC_CENTEURO is not set # CONFIG_NLS_MAC_CROATIAN is not set # CONFIG_NLS_MAC_CYRILLIC is not set # CONFIG_NLS_MAC_GAELIC is not set # CONFIG_NLS_MAC_GREEK is not set # CONFIG_NLS_MAC_ICELAND is not set # CONFIG_NLS_MAC_INUIT is not set # CONFIG_NLS_MAC_ROMANIAN is not set # CONFIG_NLS_MAC_TURKISH is not set # CONFIG_NLS_UTF8 is not set

# # Kernel hacking #

# # printk and dmesg options # CONFIG_PRINTK_TIME=y CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4 # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_DYNAMIC_DEBUG is not set

# # Compile-time checks and compiler options # CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_INFO_REDUCED is not set # CONFIG_DEBUG_INFO_SPLIT is not set # CONFIG_DEBUG_INFO_DWARF4 is not set # CONFIG_GDB_SCRIPTS is not set # CONFIG_ENABLE_WARN_DEPRECATED is not set # CONFIG_ENABLE_MUST_CHECK is not set CONFIG_FRAME_WARN=2048 # CONFIG_STRIP_ASM_SYMS is not set # CONFIG_READABLE_ASM is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_PAGE_OWNER is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_SECTION_MISMATCH is not set # CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set CONFIG_MAGIC_SYSRQ=y CONFIG_MAGIC_SYSRQ_DEFAULT_ENABLE=0x1 CONFIG_DEBUG_KERNEL=y

# # Memory Debugging # # CONFIG_PAGE_EXTENSION is not set # CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUG_OBJECTS is not set # CONFIG_DEBUG_SLAB is not set CONFIG_HAVE_DEBUG_KMEMLEAK=y # CONFIG_DEBUG_KMEMLEAK is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_PER_CPU_MAPS is not set # CONFIG_DEBUG_SHIRQ is not set

# # Debug Lockups and Hangs # CONFIG_LOCKUP_DETECTOR=y CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1 # CONFIG_DETECT_HUNG_TASK is not set CONFIG_PANIC_ON_OOPS=y CONFIG_PANIC_ON_OOPS_VALUE=1 CONFIG_PANIC_TIMEOUT=1 # CONFIG_SCHED_DEBUG is not set # CONFIG_SCHEDSTATS is not set # CONFIG_SCHED_STACK_END_CHECK is not set # CONFIG_DEBUG_TIMEKEEPING is not set # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_PREEMPT is not set

# # Lock Debugging (spinlocks, mutexes, etc…) # # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_MUTEXES is not set # CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set # CONFIG_DEBUG_LOCK_ALLOC is not set # CONFIG_PROVE_LOCKING is not set # CONFIG_LOCK_STAT is not set # CONFIG_DEBUG_ATOMIC_SLEEP is not set # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set # CONFIG_LOCK_TORTURE_TEST is not set # CONFIG_STACKTRACE is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_PI_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set # CONFIG_DEBUG_CREDENTIALS is not set

# # RCU Debugging # # CONFIG_PROVE_RCU is not set # CONFIG_SPARSE_RCU_POINTER is not set # CONFIG_TORTURE_TEST is not set # CONFIG_RCU_TORTURE_TEST is not set CONFIG_RCU_CPU_STALL_TIMEOUT=60 # CONFIG_RCU_CPU_STALL_INFO is not set # CONFIG_RCU_TRACE is not set # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_NOTIFIER_ERROR_INJECTION is not set # CONFIG_FAULT_INJECTION is not set CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y CONFIG_HAVE_DYNAMIC_FTRACE=y CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y CONFIG_HAVE_SYSCALL_TRACEPOINTS=y CONFIG_HAVE_C_RECORDMCOUNT=y CONFIG_TRACING_SUPPORT=y # CONFIG_FTRACE is not set

# # Runtime Testing # # CONFIG_LKDTM is not set # CONFIG_TEST_LIST_SORT is not set # CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_RBTREE_TEST is not set # CONFIG_INTERVAL_TREE_TEST is not set # CONFIG_PERCPU_TEST is not set # CONFIG_ATOMIC64_SELFTEST is not set # CONFIG_TEST_HEXDUMP is not set # CONFIG_TEST_STRING_HELPERS is not set # CONFIG_TEST_KSTRTOX is not set # CONFIG_TEST_RHASHTABLE is not set # CONFIG_DMA_API_DEBUG is not set # CONFIG_TEST_LKM is not set # CONFIG_TEST_USER_COPY is not set # CONFIG_TEST_BPF is not set # CONFIG_TEST_FIRMWARE is not set # CONFIG_TEST_UDELAY is not set # CONFIG_MEMTEST is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y # CONFIG_KGDB is not set # CONFIG_ARM_PTDUMP is not set CONFIG_STRICT_DEVMEM=y CONFIG_ARM_UNWIND=y CONFIG_DEBUG_USER=y CONFIG_DEBUG_LL=y CONFIG_DEBUG_ICEDCC=y # CONFIG_DEBUG_SEMIHOSTING is not set # CONFIG_DEBUG_LL_UART_8250 is not set # CONFIG_DEBUG_LL_UART_PL01X is not set CONFIG_DEBUG_LL_INCLUDE=“debug/icedcc.S” # CONFIG_DEBUG_UART_8250 is not set CONFIG_UNCOMPRESS_INCLUDE=“mach/uncompress.h” CONFIG_EARLY_PRINTK=y # CONFIG_PID_IN_CONTEXTIDR is not set # CONFIG_DEBUG_SET_MODULE_RONX is not set # CONFIG_CORESIGHT is not set

# # Security options # CONFIG_KEYS=y # CONFIG_PERSISTENT_KEYRINGS is not set # CONFIG_BIG_KEYS is not set # CONFIG_ENCRYPTED_KEYS is not set # CONFIG_SECURITY_DMESG_RESTRICT is not set # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set CONFIG_DEFAULT_SECURITY_DAC=y CONFIG_DEFAULT_SECURITY=“” CONFIG_CRYPTO=y

# # Crypto core or helper # CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_PCOMP2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y # CONFIG_CRYPTO_USER is not set CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y # CONFIG_CRYPTO_GF128MUL is not set CONFIG_CRYPTO_NULL=y # CONFIG_CRYPTO_PCRYPT is not set CONFIG_CRYPTO_WORKQUEUE=y # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_MCRYPTD is not set CONFIG_CRYPTO_AUTHENC=y # CONFIG_CRYPTO_TEST is not set

# # Authenticated Encryption with Associated Data # # CONFIG_CRYPTO_CCM is not set # CONFIG_CRYPTO_GCM is not set # CONFIG_CRYPTO_SEQIV is not set

# # Block modes # CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_CTR is not set # CONFIG_CRYPTO_CTS is not set CONFIG_CRYPTO_ECB=y # CONFIG_CRYPTO_LRW is not set # CONFIG_CRYPTO_PCBC is not set # CONFIG_CRYPTO_XTS is not set

# # Hash modes # CONFIG_CRYPTO_CMAC=m CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_XCBC is not set # CONFIG_CRYPTO_VMAC is not set

# # Digest # CONFIG_CRYPTO_CRC32C=y # CONFIG_CRYPTO_CRC32 is not set # CONFIG_CRYPTO_CRCT10DIF is not set # CONFIG_CRYPTO_GHASH is not set CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_RMD128 is not set # CONFIG_CRYPTO_RMD160 is not set # CONFIG_CRYPTO_RMD256 is not set # CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=y CONFIG_CRYPTO_SHA512=y # CONFIG_CRYPTO_TGR192 is not set # CONFIG_CRYPTO_WP512 is not set

# # Ciphers # CONFIG_CRYPTO_AES=y # CONFIG_CRYPTO_ANUBIS is not set CONFIG_CRYPTO_ARC4=y # CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_SERPENT is not set # CONFIG_CRYPTO_TEA is not set # CONFIG_CRYPTO_TWOFISH is not set

# # Compression # CONFIG_CRYPTO_DEFLATE=y # CONFIG_CRYPTO_ZLIB is not set CONFIG_CRYPTO_LZMA=y CONFIG_CRYPTO_LZO=y # CONFIG_CRYPTO_LZ4 is not set # CONFIG_CRYPTO_LZ4HC is not set

# # Random Number Generation # # CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_DRBG_MENU is not set # CONFIG_CRYPTO_USER_API_HASH is not set # CONFIG_CRYPTO_USER_API_SKCIPHER is not set # CONFIG_CRYPTO_USER_API_RNG is not set CONFIG_CRYPTO_HW=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set # CONFIG_ASYMMETRIC_KEY_TYPE is not set # CONFIG_ARM_CRYPTO is not set # CONFIG_BINARY_PRINTF is not set

# # Library routines # CONFIG_BITREVERSE=y CONFIG_HAVE_ARCH_BITREVERSE=y CONFIG_GENERIC_STRNCPY_FROM_USER=y CONFIG_GENERIC_STRNLEN_USER=y CONFIG_GENERIC_NET_UTILS=y CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y CONFIG_GENERIC_PCI_IOMAP=y CONFIG_GENERIC_IO=y CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y CONFIG_CRC_CCITT=y CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set CONFIG_CRC_ITU_T=y CONFIG_CRC32=y # CONFIG_CRC32_SELFTEST is not set CONFIG_CRC32_SLICEBY8=y # CONFIG_CRC32_SLICEBY4 is not set # CONFIG_CRC32_SARWATE is not set # CONFIG_CRC32_BIT is not set # CONFIG_CRC7 is not set # CONFIG_LIBCRC32C is not set # CONFIG_CRC8 is not set # CONFIG_AUDIT_ARCH_COMPAT_GENERIC is not set # CONFIG_RANDOM32_SELFTEST is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_LZO_COMPRESS=y CONFIG_LZO_DECOMPRESS=y CONFIG_XZ_DEC=y # CONFIG_XZ_DEC_X86 is not set # CONFIG_XZ_DEC_POWERPC is not set # CONFIG_XZ_DEC_IA64 is not set # CONFIG_XZ_DEC_ARM is not set # CONFIG_XZ_DEC_ARMTHUMB is not set # CONFIG_XZ_DEC_SPARC is not set # CONFIG_XZ_DEC_BCJ is not set # CONFIG_XZ_DEC_TEST is not set CONFIG_LZMA_COMPRESS=y CONFIG_LZMA_DECOMPRESS=y CONFIG_DECOMPRESS_GZIP=y CONFIG_GENERIC_ALLOCATOR=y CONFIG_REED_SOLOMON=y CONFIG_REED_SOLOMON_ENC8=y CONFIG_REED_SOLOMON_DEC8=y CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m CONFIG_TEXTSEARCH_FSM=m CONFIG_ASSOCIATIVE_ARRAY=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT_MAP=y CONFIG_HAS_DMA=y CONFIG_CPU_RMAP=y CONFIG_DQL=y CONFIG_NLATTR=y CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y # CONFIG_AVERAGE is not set # CONFIG_CORDIC is not set # CONFIG_DDR is not set CONFIG_LIBFDT=y # CONFIG_ARCH_HAS_SG_CHAIN is not set # CONFIG_VIRTUALIZATION is not set

# # Broadcom Specific Configurations # CONFIG_BCM_KF_MISC_MAKEFILE=y CONFIG_BCM_KF_MIPS_BCM963XX=y CONFIG_BCM_KF_ARM_BCM963XX=y CONFIG_BCM_KF_ARM64_BCM963XX=y CONFIG_BCM_KF_LINKER_WORKAROUND=y CONFIG_BCM_KF_KERN_WARNING=y CONFIG_BCM_KF_DOUBLE_INCLUSION=y CONFIG_BCM_KF_FIXADDR_TOP=y CONFIG_BCM_KF_NBUFF=y CONFIG_BCM_KF_VLAN=y CONFIG_BCM_KF_NETDEV_PATH=y CONFIG_BCM_KF_SKB_DEFINES=y CONFIG_BCM_KF_BLOG=y CONFIG_BCM_KF_VLANCTL_BIND=y CONFIG_BCM_KF_WANDEV=y CONFIG_BCM_KF_FAP=y CONFIG_BCM_KF_CSUM_UNALIGNED=y CONFIG_BCM_KF_THREAD_SIZE_FIX=y CONFIG_BCM_KF_TSTAMP=y CONFIG_BCM_KF_UNALIGNED_EXCEPTION=y CONFIG_BCM_KF_MIPS_IOPORT_BASE=y CONFIG_BCM_KF_SHOW_RAW_BACKTRACE=y CONFIG_BCM_KF_DCACHE_SHARED=y CONFIG_BCM_KF_CPU_DATA_CPUID=y CONFIG_BCM_KF_PCI_FIXUP=y CONFIG_BCM_KF_SYSRQ_AUX_CHAR=y CONFIG_BCM_KF_CHAR_SYSRQ=y CONFIG_BCM_KF_MTD_BCMNAND=y CONFIG_BCM_KF_MTD_BCM963XX=y CONFIG_BCM_KF_MTD_OOB_AUTO=y CONFIG_BCM_KF_MTD_IOCTL_FIX=y # CONFIG_BCM_KF_PPP is not set CONFIG_BCM_KF_PROC_BCM=y CONFIG_BCM_KF_IKOS=y CONFIG_BCM_KF_LOG=y CONFIG_BCM_KF_TRACE_CUSTOM=y CONFIG_BCM_KF_CGROUP=y # CONFIG_BCM_KF_HARDIRQ_CYCLES is not set CONFIG_BCM_KF_CONSOLE_LOGLEVEL=y CONFIG_BCM_KF_SHOW_HEAP_STACK=y CONFIG_BCM_KF_BYPASS_SMP_WARNING=y CONFIG_BCM_KF_OOM_REBOOT=y CONFIG_BCM_KF_VMSCAN_OPT=y CONFIG_BCM_KF_CPP_SUPPORT=y CONFIG_BCM_KF_IGMP=y CONFIG_BCM_KF_IGMP_RATE_LIMIT=y CONFIG_BCM_KF_MLD=y CONFIG_BCM_KF_MROUTE=y CONFIG_BCM_KF_IGMP_RIP_ROUTER=y CONFIG_BCM_KF_MCAST_GR_SUPPRESSION=y CONFIG_BCM_KF_MCAST=y CONFIG_BCM_KF_MISC_IOCTLS=y # CONFIG_BCM_KF_MISALIGN_MQS is not set CONFIG_BCM_KF_NETFILTER=y CONFIG_BCM_KF_ENET_SWITCH=y CONFIG_BCM_KF_FAIL_CONFIG_ON_EOF=y CONFIG_BCM_KF_RUNNER=y CONFIG_BCM_KF_WL=y CONFIG_BCM_KF_LINKWATCH_WQ=y CONFIG_BCM_KF_IP=y CONFIG_BCM_KF_SPU=y CONFIG_BCM_KF_80211=y CONFIG_BCM_KF_BUZZZ=y CONFIG_BCM_KF_ATM_BACKEND=y CONFIG_BCM_KF_EXTRA_DEBUG=y CONFIG_BCM_KF_SPI=y CONFIG_BCM_KF_MUTEX_FIX=y CONFIG_BCM_KF_POWER_SAVE=y CONFIG_BCM_KF_MODULE_OWNER=y CONFIG_BCM_KF_RCU_CONSTANT_BUG=y CONFIG_BCM_KF_JFFS=y CONFIG_BCM_KF_PROC_DEFAULT=y CONFIG_BCM_KF_ASSERT=y CONFIG_BCM_KF_EXTSTATS=y CONFIG_BCM_KF_USB_STORAGE=y CONFIG_BCM_KF_USBNET=y CONFIG_BCM_KF_FAP_GSO_LOOPBACK=y CONFIG_BCM_KF_PROTO_IPSEC=y CONFIG_BCM_KF_PROTO_ESP=y CONFIG_BCM_KF_PRINTK_INT_ENABLED=y CONFIG_BCM_KF_LIMITED_IFINDEX=y CONFIG_BCM_KF_BRIDGE_PORT_ISOLATION=y CONFIG_BCM_KF_BRIDGE_STP=y CONFIG_BCM_KF_STP_LOOP=y CONFIG_BCM_KF_BRIDGE_STATIC_FDB_MOVE=y CONFIG_BCM_KF_BRIDGE_MAC_FDB_LIMIT=y CONFIG_BCM_KF_IEEE1905=y CONFIG_BCM_KF_FBOND=y CONFIG_BCM_KF_MCAST_RP_FILTER=y CONFIG_BCM_KF_XT_MATCH_LAYER7=y CONFIG_BCM_KF_XT_TARGET_DC=y CONFIG_BCM_KF_VLAN_AGGREGATION=y CONFIG_BCM_KF_ETHTOOL=y CONFIG_BCM_KF_DEBUGGING_DISABLED_FIX=y CONFIG_BCM_KF_CPU_DOWN_PREEMPT_ON=y CONFIG_BCM_KF_IPV6RD_SECURITY=y CONFIG_BCM_KF_DPI=y CONFIG_BCM_KF_ARM_ERRATA_798181=y CONFIG_BCM_KF_ARM_PLD=y CONFIG_BCM_KF_MISC_3_4_CVE_PORTS=y CONFIG_BCM_KF_MISC_BACKPORTS=y CONFIG_BCM_KF_SCHED_RT=y CONFIG_BCM_KF_SCHED_RT_SHARE=y CONFIG_BCM_KF_ONDEMAND=y CONFIG_BCM_KF_INTERACTIVE=y CONFIG_BCM_KF_EMMC=y CONFIG_BCM_KF_USB_HOSTS=y CONFIG_BCM_KF_ACCEL_PPTP=y CONFIG_BCM_KF_RTPRIO_DEF=y CONFIG_BCM_KF_SPDSVC=y CONFIG_BCM_KF_LEDS=y CONFIG_BCM_KF_BRIDGE_COUNTERS=y CONFIG_BCM_KF_IRQ_AFFINITY=y CONFIG_BCM_KF_ANDROID=y CONFIG_BCM_KF_MHI=y CONFIG_BCM_KF_PHONET=y CONFIG_BCM_KF_M2M_DMA=y CONFIG_BCM_KF_RECVFILE=y CONFIG_BCM_KF_FILENAME_CHECK=y CONFIG_BCM_KF_BLUETOOTH_VENDOR_ID=y CONFIG_BCM_KF_SPEEDYGET=y CONFIG_BCM_KF_512MB_DDR=y CONFIG_BCM_KF_TCP_NO_TSQ=y CONFIG_BCM_KF_TMS=y CONFIG_BCM_KF_UBI=y CONFIG_BCM_KF_HNDROUTER=y CONFIG_BCM_KF_WDT=y CONFIG_BCM_KF_INTF_BRG=y CONFIG_BCM_KF_MPTCP=y CONFIG_BCM_KF_KBONDING=y CONFIG_BCM_KF_MAP=y CONFIG_BCM_KF_ASTRA=y CONFIG_BCM_KF_OVERLAYFS_BACKPORTS=y CONFIG_BCM_KF_COHERENT_OUTER_SHARED=y CONFIG_BCM_KF_JFFS2_OVERLAY=y CONFIG_BCM_KF_UBIFS_OVERLAY_BACKPORTS=y CONFIG_BCM_KF_NETFILTER_SIP=y # CONFIG_BRCM_IKOS is not set CONFIG_BCM_CHIP_NUMBER=63138 CONFIG_BCM_CHIP_REV=0x63138 CONFIG_BCM_KERNEL_CUSTOM=y # CONFIG_BCM947189 is not set # CONFIG_BCM963148 is not set CONFIG_BCM963138=y # CONFIG_MACH_BCM963148 is not set CONFIG_MACH_BCM963138=y CONFIG_BOARD_ZRELADDR=0x00008000 # CONFIG_ARCH_BCM947XXX is not set CONFIG_BOARD_PARAMS_PHYS=0x00000000 CONFIG_DEBUG_UART_ADDR=0xfffe8600 # CONFIG_BCM63138_SIM is not set CONFIG_BCM_SCHED_RT_PERIOD=100000 CONFIG_BCM_SCHED_RT_RUNTIME=99000 # CONFIG_BCM_SCHED_RT_SHARE is not set CONFIG_BCM_BOARD=y CONFIG_BCM_CHIPINFO=m CONFIG_BCM_PLATFORM=y CONFIG_BCM_OTP=m CONFIG_BCM_SERIAL=y CONFIG_BCM_SERIAL_CONSOLE=y CONFIG_BCM_EXT_TIMER=y CONFIG_BCM_WATCHDOG_TIMER=y CONFIG_ACCEL_PPTP=y CONFIG_BCM_PKTFLOW=m CONFIG_BCM_FHW=y # CONFIG_BCM_PKTCMF is not set CONFIG_BCM_PKTRUNNER=m CONFIG_BCM_PKTRUNNER_GSO=y CONFIG_BCM_PKTRUNNER_CSUM_OFFLOAD=y # CONFIG_BCM_PKTRUNNER_MCAST_DNAT is not set # CONFIG_BCM_LTE is not set # CONFIG_BCM_FBOND is not set # CONFIG_BCM_SYSPERF is not set # CONFIG_BCM_UBUSCAP is not set CONFIG_BCM_INGQOS=m CONFIG_BCM_BPM=y # CONFIG_BCM_TM is not set # CONFIG_BCM_SPDSVC is not set CONFIG_BCM_BPM_BUF_MEM_PRCNT=15 # CONFIG_BCM_PKTDMA is not set CONFIG_BCM_RDPA_MCAST=y CONFIG_BCM_ENET=m CONFIG_BCM_DEF_NR_RX_DMA_CHANNELS=2 CONFIG_BCM_DEF_NR_TX_DMA_CHANNELS=2 # CONFIG_EPON_SDK is not set # CONFIG_BCM_SFP is not set CONFIG_BCM_I2C_BUS_IMPL=1 CONFIG_BCM_I2C_CHIP_IMPL=1 # CONFIG_BCM_LASER is not set CONFIG_BCM_MAX_GEM_PORTS=32 # CONFIG_BCM_MoCA is not set # CONFIG_BCM_HS_UART is not set CONFIG_BCM_DEFAULT_CONSOLE_LOGLEVEL=8 CONFIG_BCM_LOG=y CONFIG_BCM_COLORIZE_PRINTS=y # CONFIG_BCM_ASSERTS is not set # CONFIG_BCM_FATAL_ASSERTS is not set CONFIG_BCM_I2C_BUS=y CONFIG_BCM_I2C_CHIP=y # CONFIG_BCM_I2S is not set CONFIG_BCM_VLAN=m # CONFIG_BCM_EPON_STACK is not set # CONFIG_BCM_USBNET_ACCELERATION is not set # CONFIG_BCM_SATA_TEST is not set # CONFIG_BCM_M2M_DMA is not set # CONFIG_BCM_SPEEDYGET is not set CONFIG_BCM_WLAN=m # CONFIG_BCM_WAPI is not set CONFIG_BCM_WLAN_WLVISUALIZATION=y CONFIG_BCM_WLAN_WBD=y CONFIG_BCM_WLALTBLD=“default” CONFIG_BCM_WLAN_IMPL=32 CONFIG_BCM_PCI=y CONFIG_BCM_PCIE_HCD=y CONFIG_BCM_PCIE_HCD_IMPL=1 # CONFIG_BCM_PCIE_SSC is not set # CONFIG_BCM_WLAN_USBAP is not set # CONFIG_BCM_XTMCFG is not set # CONFIG_BCM_XTMRT is not set # CONFIG_BCM_ADSL is not set # CONFIG_BCM_DSL_GINP_RTX is not set # CONFIG_BCM_DSL_GFAST is not set CONFIG_BCM_VOICE_SUPPORT=y CONFIG_BCM_SLICSLAC=m CONFIG_BCM_DSPHAL=m # CONFIG_BCM_DECT_SUPPORT is not set CONFIG_BCM_PWRMNGT=m CONFIG_BCM_ETH_PWRSAVE=y CONFIG_BCM_ENERGY_EFFICIENT_ETHERNET=y CONFIG_BCM_ETH_DEEP_GREEN_MODE=y CONFIG_BCM_ETH_HWAPD_PWRSAVE=y # CONFIG_BCM_CPUIDLE_CLK_DIVIDER is not set # CONFIG_BCM_DDR_SELF_REFRESH_PWRSAVE is not set # CONFIG_BCM_AVS_PWRSAVE is not set # CONFIG_BCM_PROCFS is not set CONFIG_BCM_TRNG=m CONFIG_BCM_TMS=m CONFIG_BCM_PMC=y # CONFIG_BCM_PLC_BOOT is not set # CONFIG_BCM_IEEE1905 is not set # CONFIG_BCM_BMU is not set # CONFIG_BCM_DPI is not set # CONFIG_BCM_MAP is not set CONFIG_BCM_BOARD_IMPL=1 CONFIG_BCM_CHIPINFO_IMPL=1 CONFIG_BCM_PLATFORM_IMPL=1 CONFIG_BCM_OTP_IMPL=1 CONFIG_BCM_SERIAL_IMPL=1 CONFIG_BCM_EXT_TIMER_IMPL=1 CONFIG_BCM_TRNG_IMPL=2 CONFIG_BCM_PKTFLOW_IMPL=1 CONFIG_BCM_PKTRUNNER_IMPL=2 CONFIG_BCM_INGQOS_IMPL=1 CONFIG_BCM_BPM_IMPL=1 CONFIG_BCM_ENET_IMPL=5 CONFIG_BCM_LOG_IMPL=1 CONFIG_BCM_VLAN_IMPL=1 CONFIG_BCM_SLICSLAC_IMPL=1 CONFIG_BCM_DSPHAL_IMPL=1 CONFIG_BCM_PWRMNGT_IMPL=1 CONFIG_BCM_PMC_IMPL=1 CONFIG_BCM_TMS_IMPL=1 # CONFIG_BCM_PORTS_ON_INT_EXT_SW is not set # CONFIG_BCM_VLAN_ROUTED_WAN_USES_ROOT_DEV_MAC is not set CONFIG_ROOT_FLASHFS=“ro noinitrd” # CONFIG_BRCM_KTOOLS is not set CONFIG_BCM_EXT_SWITCH=y CONFIG_BCM_EXT_SWITCH_TYPE=63100 CONFIG_BCM_JUMBO_FRAME=y # CONFIG_BCM_USER_DEFINED_DEFAULT_MTU is not set # CONFIG_BCM_IGNORE_BRIDGE_MTU is not set # CONFIG_AUXFS_JFFS2 is not set # CONFIG_BRCM_OLT_FPGA_RESTORE is not set # CONFIG_BCM_DCACHE_SHARED is not set CONFIG_BCM_CPU_ARCH_NAME=“arma9” # CONFIG_BCM_PRINTK_INT_ENABLED is not set CONFIG_BCM_BDMF=m CONFIG_BCM_RDP=y CONFIG_BCM_RDPA=m # CONFIG_BCM_SIM_CARD is not set CONFIG_BCM_RDPA_GPL=m CONFIG_BCM_RDPA_GPL_EXT=m CONFIG_BCM_RDPA_MW=m CONFIG_BCM_RDPA_DRV=m CONFIG_BCM_WIFI_FORWARDING_DRV=m # CONFIG_BCM_NETXL is not set CONFIG_BCM_DHD_RUNNER=y CONFIG_BCM_RDPA_GPL_EXT_IMPL=1 CONFIG_BCM_WIFI_FORWARDING_DRV_IMPL=1 CONFIG_BCM_RDPA_MW_IMPL=1 CONFIG_BCM_RDPA_DRV_IMPL=1 # CONFIG_BCM_BRIDGE_MAC_FDB_LIMIT is not set # CONFIG_BCM_ZONE_ACP is not set # CONFIG_MTD_BCM_SPI_NAND is not set # CONFIG_BCM_DSL_TX_RX_IUDMA is not set # CONFIG_BCM_WAN_2_WAN_FWD_ENABLED is not set # CONFIG_BCM_KERNEL_BONDING is not set # CONFIG_BCM_OCF is not set # CONFIG_BCM_BLUETOOTH_USB is not set # CONFIG_BCM_NFC_I2C is not set # CONFIG_BRCM_MINIGW is not set # CONFIG_BCM_512MB_DDR is not set CONFIG_BCM_CFE_XARGS=y CONFIG_BCM_CFE_XARGS_EARLY=y CONFIG_BCM_CFE_XARGS_EARLY_SIZE=0x00000400 # CONFIG_BCM_HNDROUTER is not set CONFIG_BCM_ARM_CPUIDLE=y # CONFIG_BCM_ASTRA is not set CONFIG_BCM_DHD_RUNNER_GSO=y # CONFIG_BCM_THERMAL is not set # CONFIG_BCM_CPUOFF is not set # CONFIG_BCM_INTF_BRG_ENABLED is not set # CONFIG_BCM_MPTCP is not set # CONFIG_BCM_OVERLAYFS_BACKPORTS is not set # CONFIG_BCM_JFFS2_OVERLAY is not set # CONFIG_BCM_UBIFS_OVERLAY_BACKPORTS is not set # CONFIG_BCM_GIC_NOOFNODE is not set

# # Autodetected Drivers #

# # MCAST # CONFIG_BCM_MCAST=m CONFIG_BCM_MCAST_IMPL=1 CONFIG_BR_IGMP_SNOOP=y CONFIG_BR_MLD_SNOOP=y

# # PDC #

# # CRYPTODEV # # CONFIG_BCM_CRYPTODEV is not set

# # SPU # # CONFIG_BCM_SPU is not set CONFIG_BCM_IN_KERNEL=y

root@Inteno:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 10000000 00020000 "brcmnand.0"
mtd1: 004e0000 00020000 "kernel_0"
mtd2: 004e0000 00020000 "kernel_1"
mtd3: 00060000 00020000 "nvram2"
mtd4: 00020000 00020000 "nvram"
mtd5: 0f480000 00020000 "ubi"
mtd6: 00040000 00020000 "cfe_extend"
mtd7: 073c4000 0001f000 "rootfs_0"
mtd8: 073e3000 0001f000 "rootfs_1"

The device and default firmware has support for booting to primary/secondary firmware revisions.

Changing preferred boot requires root access on device, admin in juci, or access to bootloader.

If firmware fails to boot, one can access a firmware recovery menu by keeping the RESET button pushed while powering on the device.

The device will then enable a firmware-upload page on http://192.168.1.1, instead of booting into regular firmware.

The firmware recovery page can be seen here:

Dismantling the device is simple. First remove the rubber-feet underneath the device to expose the screws keeping it together. Unscrewing those should allow you to open the lid of chassis with use of light to moderate force. Please note there is a flat-cable connecting the LEDs in the lid with the main PCB.

When opened you will be exposed to the top-side of the PCB:

To reveal the bottom-side of the PCB, you have to disconnect the wifi antennas and unscrew the 2 screws in the chassis-end opposite to the network-ports and power-connector. This side of the board exposes 3 PCB-connectors:

J3 is the serial port. The function and layout of the remaining PCBs remain to be mapped.

Serial console is available on this device and can be found on the J3 PCB-connector on the bottom-side of the board (requires full dismantling).

Pinout is as follows:

 +-+-+
 |0|1|   0 = TX
 +-+-+   1 = RX 
 |2|3|   3 = GND
 +-+-+
  J3   <-- board print, for orientation

Standard serial settings apply: 115200, 8N1, with no hardware or software flow-control.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/02/18 03:31
  • by jostein