Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:hwdata:arcadyanastoria:arcadyanastoria_easybox_904_lte [2018/12/12 12:06] – [Data entry] tmomas | toh:hwdata:arcadyanastoria:arcadyanastoria_easybox_904_lte [2018/12/12 14:29] – [Data entry] tmomas | ||
|---|---|---|---|
| Line 19: | Line 19: | ||
| * --- Your wiki administration | * --- Your wiki administration | ||
| *********************************************************/ | *********************************************************/ | ||
| - | |||
| - | |||
| {{page> | {{page> | ||
| - | |||
| - | ==== Introduction ==== | ||
| - | |||
| - | The EasyBox 904 LTE is a 4G WiFi router, with a tiny 3 inch display, which has a 2.4 GHz and a 5 GHz WiFi interface, four 1G LAN ports, an ISDN RJ45 port, a 4 pin terminal also for use with ISDN and 3 TAE ports. Also there are 2 covered SMA ports for external LTE antenna, a covered SIM slot and two USB 2.0 ports (one also covered). Under the hood it has a Mini-PCIe slot, which is used for a QUANTA 1KG2 LTE modem, also connected to the SMA ports and onboard antennas. At least you can find a serial port at J8, next to the VIA VT6212L, which starts listening to 115200 baud (8N1). | ||
| - | |||
| - | For some people it might be a big surprise, but if you look at the firmware of the device (e.g. UEfullimage_AT904L-03.18.bin), | ||
| - | |||
| ===== Dataentry ===== | ===== Dataentry ===== | ||
| Line 68: | Line 59: | ||
| Modem_modem | Modem_modem | ||
| Comments network ports_ | Comments network ports_ | ||
| - | WLAN Hardwares | + | WLAN Hardwares |
| WLAN 2.4GHz_wlan24 | WLAN 2.4GHz_wlan24 | ||
| WLAN 5.0GHz_wlan50 | WLAN 5.0GHz_wlan50 | ||
| Line 76: | Line 67: | ||
| Bluetooth_bluetooth | Bluetooth_bluetooth | ||
| USB ports_port-usbs | USB ports_port-usbs | ||
| - | SATA ports_numsataport | + | SATA ports_numsataport |
| Comments USB SATA ports_ | Comments USB SATA ports_ | ||
| - | Video ports_port-videos | + | Video ports_port-videos |
| - | Audio ports_port-audios | + | Audio ports_port-audios |
| Phone ports_port-phones | Phone ports_port-phones | ||
| Comments AV ports_ | Comments AV ports_ | ||
| Line 87: | Line 78: | ||
| LED count_numled | LED count_numled | ||
| Button count_numbutton | Button count_numbutton | ||
| - | GPIOs_numgpio | + | GPIOs_numgpio |
| Power Supply | Power Supply | ||
| Device Page_page | Device Page_page | ||
| Line 113: | Line 104: | ||
| Comments_ | Comments_ | ||
| ---- | ---- | ||
| - | |||
| - | |||
| {{section>: | {{section>: | ||
| - | |||
| - | ==== Serial ==== | ||
| - | -> [[docs: | ||
| - | |||
| - | How to connect to the Serial Port of this specific device: After removing the cover (release 4 screws on the backside), you will find the serial port at J8 on the PCB, next to the VIA VT6212L. | ||
| - | |||
| - | {{: | ||
| - | |||
| - | WARNING! Use at your own risk. | ||
| - | |||
| - | ^ JP8 ^^^^ | ||
| - | ^ PIN 1 ^ PIN 2 ^ PIN 3 ^ PIN 4 ^ | ||
| - | | 3.3V | TXD | RXD | GND | | ||
| - | |||
| - | |||
| - | ^ Serial connection parameters\\ for EasyBox 904 LTE | 115200, 8N1 | | ||
| - | |||
| - | ==== OEM bootlog ==== | ||
| - | <WRAP bootlog> | ||
| - | < | ||
| - | ROM VER: 1.1.4 | ||
| - | CFG 06 | ||
| - | NAND | ||
| - | NAND Read OK | ||
| - | |||
| - | ROM VER: 1.1.4 | ||
| - | CFG 06 | ||
| - | NAND | ||
| - | NAND Read OK | ||
| - | nand_read_page - 00000008 | ||
| - | DDR autotuning Rev 0.3c | ||
| - | DDR size from 0xa0000000 - 0xa7ffffff | ||
| - | DDR check ok... start booting... | ||
| - | |||
| - | |||
| - | |||
| - | U-Boot 2010.06-Lv2.0.40-A0.3 | ||
| - | |||
| - | CLOCK CPU 500M RAM 250M | ||
| - | DRAM: 128 MiB | ||
| - | NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) | ||
| - | 512 MiB | ||
| - | Bad block table found at page 262080, version 0x01 | ||
| - | Bad block table found at page 262016, version 0x01 | ||
| - | nand_read_bbt: | ||
| - | nand_read_bbt: | ||
| - | nand_read_bbt: | ||
| - | nand_read_bbt: | ||
| - | In: serial | ||
| - | Out: | ||
| - | Err: | ||
| - | Net: | ||
| - | vr9 Switch | ||
| - | |||
| - | Type "run flash_nfs" | ||
| - | |||
| - | Hit any key to stop autoboot: | ||
| - | Uncompressing LCD bootup images ............... | ||
| - | NAND read: device 0 offset 0x0000000004700000, | ||
| - | | ||
| - | 1. bootid : 0, bootnum : 2 | ||
| - | Erasing at 0x4560000 -- 100% complete. | ||
| - | done | ||
| - | 2. bootid : 0, bootnum : 3 | ||
| - | |||
| - | NAND read: device 0 offset 0x0000000001e40000, | ||
| - | | ||
| - | ## Booting kernel from Legacy Image at 80800000 ... | ||
| - | Image Name: MIPS LTQCPE Linux-2.6.32.32 | ||
| - | | ||
| - | Image Type: MIPS Linux Kernel Image (lzma compressed) | ||
| - | Data Size: 1441728 Bytes = 1.4 MiB | ||
| - | Load Address: 80002000 | ||
| - | Entry Point: | ||
| - | | ||
| - | | ||
| - | |||
| - | Starting kernel ... | ||
| - | |||
| - | Lantiq xDSL CPE VR9 | ||
| - | mips_hpt_frequency = 250000000, counter_resolution = 2 | ||
| - | </ | ||
| - | </ | ||
| - | |||