Huawei HG658b/c

Architecture MIPS
Vendor Broadcom
bootloader cfe
Board ID 963268_hg658b
System-On-Chip Broadcom BCM63168
CPU/Speed BMIPS4350 v8.0 / 400 MHz
NAND flash 128 MiB (Spansion S34ML01G)
RAM 128 MiB / DDR2
Wireless BCM6362 802.11b/g/n (SoC)
Antenna 2x
Ethernet Integrated BCM63168 w/ vlan support swconfig
USB Yes
Power adapter 12V DC 2A / HW-120200U6W
Serial Yes
JTAG ?

port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN NAN1 BT00 0002 NAN9 BT00 0234 NAN9 NAN3 RFS1 NAN5 CFE version 1.0.38-112.70 for BCM963268 (32bit,SP,BE) Build Date: Tue May 21 11:49:17 CST 2013 (wangzhiquan@X3755-vhg) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name Spansion S34ML01G, id 0x01f1 block 128KB size 131072KB Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-0) : 963268_hg658b Number of MAC Addresses (1-32) : 10 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 0 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Boot :e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 autoRun Boot from main system! BOOT FROM MAIN SYSTEM MAIN IMAGE FOUND IMAGE CRC CHECK OK Decompression OK! Entry at 0x800146c0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x800146c0 Linux version 2.6.30 (wangzhiquan@X3755-vhg) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #10 SMP PREEMPT Wed May 22 16:12:42 CST 2013 ======== nand_flash_init ======= NAND flash device id 01f1 is not supported. Init Flash Error iReturn = -1 63268hg622b prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 07ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00007ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00007ece On node 0 totalpages: 32462 free_area_init_node: node 0, pgdat 804b2690, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 222 pages used for memmap Normal zone: 28144 pages, LIFO batch:7 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 512 (order: 9, 2048 bytes) console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Memory: 122856k/129848k available (3717k kernel code, 6820k reserved, 1048k data, 168k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 May 16 2013 20:26:41 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1152 bytes bhal: bhalInit entry NET: Registered protocol family 16 Internal 1P2 VREG is forced to remain enabled registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 May 16 2013 20:33:38 initialized Broadcom GBPM v0.1 May 16 2013 20:33:39 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 240 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 NET: Registered protocol family 24 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=01f1001d After: NandSelect=40000001, nandConfig=15142200 Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=01f1001d, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=87a6f190, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 nand_read_bbt: Bad block at 0x011e0000 brcmnandCET: Status -> Deferred brcmnand_scan 99 Boot from main system! iBlkStart 1 =======iBlkStart:2======= *******iErrCnt:1. Creating 3 MTD partitions on "brcmnand.0": 0x000000040000-0x000001d20000 : "rootfs" 0x000001d20000-0x000003a20000 : "rootfsbak" 0x000003a20000-0x000004620000 : "config" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core usbcore: registered new interface driver usbtest MoniterInit entry Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX adsl: adsl_init entry bcmxtmcfg: bcmxtmcfg_init entry bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 May 21 2013 11:45:48 bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (2028 buckets, 8112 max) xt_time: kernel timezone is -0000 nf_nat_pt: no ports specified ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 168k freed =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=1= init started: BusyBox vv1.9.1 (2013-05-16 20:40:10 CST) starting pid 263, tty '': '/etc/init.d/rcS' RCS DONE starting pid 265, tty '': '/bin/sh' BusyBox vv1.9.1 (2013-05-16 20:40:10 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. -/bin/sh: usbdiagd: not found Loading drivers and kernel modules... bcm_ingqos: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Ingress QoS Module Char Driver v0.1 May 16 2013 20:30:08 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=134217728B (128MB), buf_mem_size=13421772B (12MB), num of buffers=6403, buf size=2096 Broadcom BPM Module Char Driver v0.1 May 16 2013 20:30:07 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 May 21 2013 11:45:30 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 May 21 2013 11:45:30 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 May 16 2013 20:30:10 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Allocated FAP0 GSO Buffers (0xA661D104) : 1048576 bytes @ 0xA6700000 Allocated FAP1 GSO Buffers (0xA663D104) : 1048576 bytes @ 0xA6000000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> bcmPktDma_bind: FAP Driver binding successfull [FAP0] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP0] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP1] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP0] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP1] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP0] GSO Buffer set to 0xA6700000 [FAP1] GSO Buffer set to 0xA6000000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. Broadcom BCM63168D0 Ethernet Network Device v0.1 May 21 2013 11:45:28 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b08206f0 bytes remaining 7008 ETH Init: Ch:0 - 200 tx BDs at 0xb08206f0 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a206f0 bytes remaining 7008 ETH Init: Ch:1 - 200 tx BDs at 0xb0a206f0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821690 bytes remaining 2192 ETH Init: Ch:0 - 600 rx BDs at 0xb0821690 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21690 bytes remaining 2192 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21690 eth0.3: MAC Address: 00:66:4B:32:CE:08 eth0.5: MAC Address: 00:66:4B:32:CE:08 eth0.4: MAC Address: 00:66:4B:32:CE:08 eth0.2: MAC Address: 00:66:4B:32:CE:08 nas0: MAC Address: 00:66:4B:32:CE:08 =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=2= --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=4161 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2001.cpe.L.3 Endpoint: endpoint_init entry Endpoint: endpoint_init COMPLETED p8021ag: p8021ag_init entry IRQ 8/BCM WATCHDOG: IRQF_DISABLED is not guaranteed on shared IRQs BCM Hardware Watchdog Timer for BCM96361 USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems Start mic now ... magic number is 3e 00 84 60. base64 decrypt failed, try other decrypt Read from flash ok. load cfm ok. start log proc... ifconfig: SIOCSIFNETMASK: Cannot assign requested address br0: starting userspace STP failed, starting kernel STP add group failed: Operation not supported set group 0 mac learning disable in br0 failed: Operation not supported BcmAdsl_Initialize=0x80232C54, g_pFnNotifyCallback=0x804A61B4 lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA7FFFFF8, 0x7DFFFEFF 0xFFBFFFFF *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xD9E68 => 0x110570 *** AdslCoreSharedMemInit: shareMemAvailable=137840 AdslCoreHwReset: pLocSbSta=862e0000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA7F9AC2C fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22960 bytes remaining 592 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22960 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fa0 bytes remaining 464 XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fa0 Success ARL table flush done Success atp: cur kernel version:[2.6.30] device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode device eth0.4 entered promiscuous mode device eth0.5 entered promiscuous mode ADDRCONF(NETDEV_UP): eth0.2: link is not ready ADDRCONF(NETDEV_UP): eth0.3: link is not ready ADDRCONF(NETDEV_UP): eth0.4: link is not ready ADDRCONF(NETDEV_UP): eth0.5: link is not ready device eth0 is not a slave of br0 arp uses obsolete (PF_INET,SOCK_PACKET) wl: Unsupported device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state acsd: selected channel spec: 0x2b0b 28800 sec blinktype=5 blinktype=4 ADDRCONF(NETDEV_UP): nas0: link is not ready ethcmd add wan interface nas0.10 ok device nas0 entered promiscuous mode Use default bin /var/cwmp now ... device nas0 left promiscuous mode device nas0 entered promiscuous mode iptables: No chain/target/match by that name iptables: No chain/target/match by that name Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows Broadcom Packet Flow Cache flushing the flows iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name Broadcom Packet Flow Cache flushing the flows FILE:voicecfg.c,LINE:95,sizeof(TAPI)=1388,sizeof(SVC)=57288,sizeof(STATE)=6900 BOS: Enter bosIniBOS: Enter bosInit t bosTimerInitBOS: Exit bosInit Enter bosAppInendpoint_open COMPLETED it Exit bosAppInit BOS: Exit bosInit Use default bin /var/upnp now ... Enable Got value: 1 NATEnabled Got value: 1 ******* DSP: Found BCM963268 ******* ******* DSP: In PCM Mode ******* ******* DSP: PCM running in 16 bit mode ******* gInterruptCounter = 0xC0E54CF0 gInterruptErrors = 0xC0E54CF4 gNextRxDesc = 0xC0E54E14 gNextTxDesc = 0xC0E54E10 gDectTestMode = 0xc0c7e428 dectBuffStart = 0xc0c7e434 gDectRxOutOfSyncCounter = 0xc0c7e438 gDectTxOutOfSyncCounter = 0xc0c7e43c 32 ms ECAN tail-length *** gStartRxDesc[0] = 0xA0C00000 *** gBufferSizeBytes = 640 *** gStartTxDesc[0] = 0xA0C01000 halPcmInit 370 nextTxDesc = 0xA0C01000 halPcmInit 370 nextTxDesc = 0xA0C01008 halPcmInit 374 Ownership for TX desc not set. Use this buffer. Hausware build date=Mar 12 2012 time=15:23:18 boardHalInit completed DSP: Interrupt Masks --------------- IrqMask = 0x00001000 IrqMask1 = 0x00000400 DSP: Interrupt Status ----------------- IrqStatus = 0x00000000 IrqStatus1 = 0x00000000 EndpointInit completed Created message queue "HDSP", depth 99, id 1Endpoint Event task started with pid 1561... ioctl minFlash:80,maxFlash:250,offhook:250,onhook:250. [ERROR ept] casCtlIgnoreHookState,1049: (ts: 11s 507ms):char[2] invalid [ERROR ept] casCtlIgnoreHookState,1049: (ts: 11s 552ms):char[3] invalid [ERROR ept] casCtlIgnoreHookState,1049: (ts: 11s 597ms):char[4] invalid [ERROR ept] casCtlIgnoreHookState,1049: (ts: 11s 642ms):char[5] invalid rtcpThreadCreate started with PID 1536 [rtcpThread][242] pid[1573] --------------v 0xEB: Write Value is......0x04 oipsystem bootup0x04 success-------- ------- slicLe89116Write: Finished 0xEB: Write Value is......0x23 0x23 slicLe89116Write: Finished EVENT: endpt 0, event 4, cnxid -1 *****DSP TIMESLOT UE0 TEST OK****** 0xEB: Write Value is......0xC0 0xC0 slicLe89116Write: Finished 0xEB: Write Value is......0x04 0x04 slicLe89116Write: Finished 0xEB: Write Value is......0x04 0x04 slicLe89116Write: Finished 0xEB: Write Value is......0x23 0x23 slicLe89116Write: Finished EVENT: endpt 1, event 5, cnxid -1 *****DSP TIMESLOT UE1 TEST OK****** 0xEB: Write Value is......0xC0 0xC0 slicLe89116Write: Finished 0xEB: Write Value is......0x04 0x04 slicLe89116Write: Finished [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] Use default bin /var/upnp now ... [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] Use default bin /var/upnp now ... [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] Use default bin /var/upnp now ... [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0] [rtcpThread][249] pid[1573] [rtcpThread][272] descSet[0]


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2020/06/10 19:17
  • by danitool