User Tools

Site Tools


toh:huawei:hg520v

Huawei HG520v

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device will end after 2019.
19.07 will be the last official build for 4/32 devices. After 19.07, no further OpenWrt images will be built for 4/32 devices. See OpenWrt on 4/32 devices what you can do now.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when chosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.
See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

Supported Versions

Hardware Highlights

Installation

Flashing ANY Firmware

You must set your TCP/IP v4 protocol to:

  1. IP: 192.168.1.2
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1
  4. DNS: (optional, can be blank).

Then:

  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Acces to http://192.168.1.1 and upload binary file.
  5. Wait until router reboots.

Hardware

Info

Instruction set MIPS
Vendor Broadcom
bootloader cfe
Board Id HW6358GW_B
System-On-Chip Broadcom BCM6359
vDSL AFE Broadcom BCM6505
vDSL Tranceiver Broadcom BCM6314
CPU/Speed BMIPS32 / 300 MHz
Flash-Chip AM29LV320MT
Flash size 4 MiB
RAM 32 MiB
Wirless BCM4318 (14e4:4318) 802.11b/g
Ethernet Broadcom BCM5325 w/ vlan support swconfig
USB ?
Antenna 2x
Serial Yes
JTAG ?

Photos

Router

Board Front

vDSL Chips

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

GPIO

LEDs

Read: System configuration: Leds to configure the leds

Pin Event Active
? power (green) ?
? dsl (green) ?
32 inet (green) Low

Buttons

hardware.button on howto use and configure the hardware button(s).

Pin Event Active
37 Reset Low

Bootlogs

OEM Bootlog

CFE version cfe.d060.5002 for BCM96358 (32bit,SP,BE) Build Date: Èý 10ÔÂ 18 13:16:46 CST 2006 (yuyouqing42304) Copyright (C) 2006 Huawei Technologies Co. Ltd. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB setBoardIdName is forced HW6358GW_B. CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz Total memory: 33554432 bytes (32MB) Total memory used by CFE: 0x80401000 - 0x80528770 (1210224) Initialized Data: 0x8041DA90 - 0x8041FE30 (9120) BSS Area: 0x8041FE30 - 0x80426770 (26944) Local Heap: 0x80426770 - 0x80526770 (1048576) Stack Area: 0x80526770 - 0x80528770 (8192) Text (code) segment: 0x80401000 - 0x8041DA90 (117392) Boot area (physical): 0x00529000 - 0x00569000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id Name : HW6358GW_B Psi size in KB : 64 Number of MAC Addresses (1-32) : 11 Base MAC Address : XX:XX:XX:XX:XX:XX Ethernet PHY Type : Internal Memory size in MB : 32 CMT Thread Number : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Code Address: 0x80010000, Entry Address: 0x801bf018 Decompression OK! Entry at 0x801bf018 Starting program at 0x801bf018 Linux version 2.6.8.1 (root@localhost) (gcc version 3.4.2) #1 Fri Nov 21 15:49:4 3 CST 2008 Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB Total Flash size: 4096K with 71 sectors Board id is set HW6358GW_B HW6358GW_B prom init CPU revision is: 0002a010 mpi: No Card is in the PCMCIA slot Determined physical RAM map: memory: 01ff1920 @ 00000000 (usable) On node 0 totalpages: 8177 DMA zone: 8177 pages, LIFO batch:1 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd brcm mips: enabling icache and dcache... Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 16kB 2-way, linesize 16 bytes. PID hash table entries: 128 (order 7: 1024 bytes) Using 150.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 30340k/32708k available (1503k kernel code, 2348k reserved, 217k data, 7 2k init, 0k highmem) Calibrating delay loop... 299.00 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Can't analyze prologue code at 8018647c Initializing Cryptographic API PPP generic driver version 2.4.2 NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 brcmboard: brcm_board_init entry SES: Button Interrupt 0x3 is enabled bcm963xx_serial driver v2.0 u32 classifier NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 72k freed init started: BusyBox v1.00 (2008.11.21-07:54+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.00 (2008.11.21-07:54+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. blaadd: blaa_detect entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6358A1 Ethernet Network Device v0.3 Nov 21 2008 15:48:15 Config Ethernet Switch Through MDIO Pseudo PHY Interface dgasp: kerSysRegisterDyingGaspHandler: eth0 registered ======oh oh dev name is eth0.0 ======oh oh dev name is eth0.1 eth0: MAC Address: XX:XX:XX:XX:XX:XX PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:01.0 (0004 -> 0006) wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board) wl0 MAC Address: XX:XX:XX:XX:XX:XX wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe2.3 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0) ip is 192.168.1.1mask is 255.255.255.0, ipbegin is 192.168.1.33, ipend is 19 2.168.1.254 wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0) bcmSetAtmConfigMode Current mode is:atmctl configmode ptmprotocol adslctl: not found adslctl: not found ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (255 buckets, 0 max) - 368 bytes per conntrack ip_conntrack_pptp version 2.1 loaded ip_nat_pptp version 2.0 loaded ip_nat_irc: Unknown symbol needs_ip_conntrack_irc insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_irc .ko': Success (2): Success VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,42: BCM6505 reset and ADSL/VDSL mode selection. =========pchr is:atmctl traffic atm atmctl intf --settype 0 utopia level2 VDSLCTL FAILURE at bcm_socket.c,177: could not connect. RELAY INFO at bcm_socket.c,199: Try socket connection for 90 seconds. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,47: hpi_Init. HSTMGR INFO at bcm_transfer.c,51: utopia_Init. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_boot.c,95: Booting the BCM17f7 device 0. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,168: Setting PLL speed. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[3] = 0x8a. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[2] = 0x3e. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[VDSLCTL FAILURE at bcm_soc ket.c,177: could not connect. 1] = 0x21. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[0] = 0x13. HSTMGR INFO at bcm_transfer.c,186: Wait for PLL lock. HSTMGR INFO at bcm_transfer.c,197: PLL locked OK. HSTMGR INFO at bcm_transfer.c,204: Select PLL. HSTMGR INFO at bcm_transfer.c,212: PLL Active (assumed). HSTMGR INFO at bcm_transfer.c,132: 6510 Magic Register = 0x03. Loading image .. done HSTMGR INFO at bcm_boot.c,245: Boot firmware release: 4.0.0. HSTMGR INFO at bcm_boot.c,248: HMI download protocol: 1.0. Loading target image through HMI: 0%  0% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 0%  0%  0%  0%  0%  0%  1%  1%  1%  1%  1%  1%  1%  2%  2%  2%  2%  2%  2%  2%  3%  3%  3%  3%  3%  3%  3%  4%  4%  4%  4%  4%  4%  5%  5%  5%  5%  5%  5%  5%  6%  6%  6%  6%  6%  6%  6%  7%  7%  7%  7%  7%  7%  7%  8%  8%  8%  8%  8%  8%  8%  9%  9%  9%  9%  9%  9% 10% 10% 10% 10% 10% 10% 10% 11% 11% 11% 11% 11% 11% 11% 12% 12% 12% 12% 12% 12% 12% 13% 13% 13% 13% 13% 13% 14% 14% 14% 14% 14% 14% 14% 15% 15% 15% 15% 15% 15% 15% 16% 16% 16% 16% 16% 16% 16% 17% 17% 17% 17% 17% 17% 17% 18% 18% 18% 18% 18% 18% 19% 19% 19% 19% 19% 19% 19% 20% 20% 20% 20% 20% 20% 20% 21% 21% 21% 21% 21% 21% 21% 22% 22% 22% 22% 22% 22% 22% 23% 23% 23% 23% 23% 23% 24% 24% 24% 24% 24% 24% 24% 25% 25% 25% 25% 25% 25% 25% 26% 26% 26% 26% 26% 26% 26% 27% 27% 27% 27% 27% 27% 28% 28% 28% 28% 28% 28% 28% 29% 29% 29% 29% 29% 29% 29% 30% 30% 30% 30% 30% 30% 30% 31% 31% 31% 31% 31% 31% 31% 32% 32% 32% 32% 32% 32% 33% 33% 33% 33% 33% 33% 33% 34% 34% 34% 34% 34% 34% 34% 35% 35% 35% 35% 35% 35% 35% 36% 36% 36% 36% 36% 36% 36% 37% 37% 37% 37% 37% 37% 38% 38% 38% 38% 38% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 38% 38% 39% 39% 39% 39% 39% 39% 39% 40% 40% 40% 40% 40% 40% 40% 41% 41% 41% 41% 41% 41% 42% 42% 42% 42% 42% 42% 42% 43% 43% 43% 43% 43% 43% 43% 44% 44% 44% 44% 44% 44% 44% 45% 45% 45% 45% 45% 45% 45% 46% 46% 46% 46% 46% 46% 47% 47% 47% 47% 47% 47% 47% 48% 48% 48% 48% 48% 48% 48% 49% 49% 49% 49% 49% 49% 49% 50% 50% 50% 50% 50% 50% 51% 51% 51% 51% 51% 51% 51% 52% 52% 52% 52% 52% 52% 52% 53% 53% 53% 53% 53% 53% 53% 54% 54% 54% 54% 54% 54% 54% 55% 55% 55% 55% 55% 55% 56% 56% 56% 56% 56% 56% 56% 57% 57% 57% 57% 57% 57% 57% 58% 58% 58% 58% 58% 58% 58% 59% 59% 59% 59% 59% 59% 59% 60% 60% 60% 60% 60% 60% 61% 61% 61% 61% 61% 61% 61% 62% 62% 62% 62% 62% 62% 62% 63% 63% 63% 63% 63% 63% 63% 64% 64% 64% 64% 64% 64% 65% 65% 65% 65% 65% 65% 65% 66% 66% 66% 66% 66% 66% 66% 67% 67% 67% 67% 67% 67% 67% 68% 68% 68% 68% 68% 68% 68% 69% 69% 69% 69% 69% 69% 70% 70% 70% 70% 70% 70% 70% 71% 71% 71% 71% 71% 71% 71% 72% 72% 72% 72% 72% 72% 72% 73% 73% 73% 73% 73% 73% 73% 74% 74% 74% 74% 74% 74% 75% 75% 75% 75% 75% 75% 75% 76% 76% 76% 76% 76% 76% 76% 77% 77% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 77% 77% 77% 77% 77% 78% 78% 78% 78% 78% 78% 79% 79% 79% 79% 79% 79% 79% 80% 80% 80% 80% 80% 80% 80% 81% 81% 81% 81% 81% 81% 81% 82% 82% 82% 82% 82% 82% 82% 83% 83% 83% 83% 83% 83% 84% 84% 84% 84% 84% 84% 84% 85% 85% 85% 85% 85% 85% 85% 86% 86% 86% 86% 86% 86% 86% 87% 87% 87% 87% 87% 87% 88% 88% 88% 88% 88% 88% 88% 89% 89% 89% 89% 89% 89% 89% 90% 90% 90% 90% 90% 90% 90% 91% 91% 91% 91% 91% 91% 91% 92% 92% 92% 92% 92% 92% 93% 93% 93% 93% 93% 93% 93% 94% 94% 94% 94% 94% 94% 94% 95% 95% 95% 95% 95% 95% 95% 96% 96% 96% 96% 96% 96% 96% 97% 97% 97% 97% 97% 97% 98% 98% 98% 98% 98% 98% 98% 99% 99% 99% 99% 99% 99% 99% done HSTMGR INFO at bcm_hostMgr.c,94: Interrupt polling enabled. bind now the file descriptor from IP 0.0.0.0, my port 57665. vdslctl: Started successfully RELAY INFO at bcm_socket.c,224: Connected successfully (fd: 6). =========pchr is:atmctl traffic atm ==> Bcm963xx VDSL Software Version: 09.02.07, 2006-11-15 <== ==> Bcm963xx Software Version: V100R001C02B066_V_SP3 <== atmctl intf --settype 0 utopia level2 ========bcm63xx_enet_open dev->name is:eth0 device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state pvc2684ctl_main trafficmode:2 pvc2684d_main:2 setIndexName1 pvc2684d: Interface "nas_0_32_0" created sucessfully AttachVcc g_nPtmConfig:2 setIndexName1 pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC device nas_0_32_0 entered promiscuous mode br0: port 2(nas_0_32_0) entering learning state br0: topology change detected, propagating br0: port 2(nas_0_32_0) entering forwarding state device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state eth0.2: MAC Address: XX:XX:XX:XX:XX:XX eth0.3: MAC Address: XX:XX:XX:XX:XX:XX eth0.4: MAC Address: XX:XX:XX:XX:XX:XX eth0.5: MAC Address: XX:XX:XX:XX:XX:XX device eth0.2 entered promiscuous mode br0: port 1(eth0.2) entering learning state br0: topology change detected, propagating br0: port 1(eth0.2) entering forwarding state device eth0.3 entered promiscuous mode br0: port 3(eth0.3) entering learning state br0: topology change detected, propagating br0: port 3(eth0.3) entering forwarding state device eth0.4 entered promiscuous mode br0: port 4(eth0.4) entering learning state br0: topology change detected, propagating br0: port 4(eth0.4) entering forwarding state device eth0.5 entered promiscuous mode br0: port 5(eth0.5) entering learning state br0: topology change detected, propagating br0: port 5(eth0.5) entering forwarding state In webmain, setup wlan br0: port 1(eth0.2) entering disabled state br0: port 3(eth0.3) entering disabled state br0: port 4(eth0.4) entering disabled state br0: port 5(eth0.5) entering disabled state Login:


OpenWrt

[ 0.000000] Linux version 3.6.11 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Wed Jan 9 20:07:04 CET 2013 [ 0.000000] Detected Broadcom 0x6358 CPU revision a1 [ 0.000000] CPU frequency is 300 MHz [ 0.000000] 32MB of RAM installed [ 0.000000] registering 40 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xbfc00000 [ 0.000000] board_bcm963xx: CFE version: 100.48.54-48.46 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: HW6358GW_B [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802a8db0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 28356k/32768k available (2260k kernel code, 4412k reserved, 400k data, 1072k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.032000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.080000] bio: create slab <bio-0> at 0 [ 0.088000] PCI host bridge to bus 0000:00 [ 0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.096000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.104000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff] [ 0.104000] pci 0000:00:01.0: [14e4:4318] type 00 class 0x028000 [ 0.104000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00001fff] [ 0.116000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.116000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff] [ 0.120000] Switching to clocksource MIPS [ 0.132000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.136000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64 [ 0.160000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00 [ 0.168000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243) [ 0.168000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243) [ 0.168000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243) [ 0.168000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243) [ 0.208000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.216000] NET: Registered protocol family 2 [ 0.224000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.232000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.236000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.244000] TCP: reno registered [ 0.248000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.252000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.264000] PCI: CLS 0 bytes, default 16 [ 2.744000] audit: initializing netlink socket (disabled) [ 2.748000] type=2000 audit(2.748:1): initialized [ 2.756000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.760000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.772000] msgmni has been set to 55 [ 2.776000] io scheduler noop registered [ 2.780000] io scheduler deadline registered (default) [ 2.788000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart [ 2.796000] console [ttyS0] enabled, bootconsole disabled [ 2.812000] physmap platform flash device: 00400000 at 1fc00000 [ 2.816000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01 [ 2.828000] Amd/Fujitsu Extended Query Table at 0x0040 [ 2.832000] Amd/Fujitsu Extended Query version 1.3. [ 2.840000] physmap-flash.0: Swapping erase regions for top-boot CFI table. [ 2.844000] number of CFI chips: 1 [ 2.848000] bcm63xxpart: CFE boot tag found with version 6 and board type HW6358GW_B [ 2.856000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 2.864000] bcm63xxpart: Partition 1 is rootfs offset 10100 and length 2bb000 [ 2.872000] bcm63xxpart: Partition 2 is kernel offset 2cb100 and length 8aac4 [ 2.880000] bcm63xxpart: Partition 3 is nvram offset 3f0000 and length 10000 [ 2.884000] bcm63xxpart: Partition 4 is linux offset 10000 and length 3e0000 [ 2.892000] bcm63xxpart: Spare partition is offset 360000 and length 90000 [ 2.900000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 2.908000] Creating 5 MTD partitions on "physmap-flash.0": [ 2.912000] 0x000000000000-0x000000010000 : "CFE" [ 2.920000] 0x000000010100-0x0000002cb100 : "rootfs" [ 2.928000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.944000] mtd: partition "rootfs" set to be root filesystem [ 2.948000] split_squashfs: no squashfs found in "physmap-flash.0" [ 2.956000] 0x0000002cb100-0x000000355bc4 : "kernel" [ 2.960000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.976000] 0x0000003f0000-0x000000400000 : "nvram" [ 2.988000] 0x000000010000-0x0000003f0000 : "linux" [ 3.004000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 3.012000] TCP: cubic registered [ 3.016000] NET: Registered protocol family 17 [ 3.020000] 8021q: 802.1Q VLAN Support v1.8 [ 3.044000] Freeing unused kernel memory: 1072k freed [ 4.132000] roboswitch: Probing device 'eth0' [ 4.136000] roboswitch: found a 5325! It's a 5350. at eth0 [ 5.192000] There is already a switch registered on the device 'eth0' [ 10.164000] There is already a switch registered on the device 'eth0' [ 10.192000] Button Hotplug driver version 0.4.1 [ 10.240000] PPP generic driver version 2.4.2 [ 10.332000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.536000] NET: Registered protocol family 24 [ 10.568000] nf_conntrack version 0.5.0 (459 buckets, 1836 max) [ 10.924000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542) v0.1.2 [ 15.640000] eth0: link forced UP - 100/full - flow control off/off [ 62.056000] eth0: link forced UP - 100/full - flow control off/off [ 62.068000] device eth0 entered promiscuous mode [ 62.076000] br-lan: port 1(eth0) entered forwarding state [ 62.080000] br-lan: port 1(eth0) entered forwarding state [ 64.084000] br-lan: port 1(eth0) entered forwarding state


Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/huawei/hg520v.txt · Last modified: 2019/02/12 21:16 by tmomas