HPE 1920-8G (JG920A) HNGZA-HA0008

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

HPE (Hewlett Packard Enterprise) OfficeConnect 1920 Series Switch.

The 1920 series features a variable number of gigabit (1000BASE-T / IEEE 802.3ab) ports, as well as a smaller number of 1 Gbit/s SFP ports.

The JG920A variant features 8 1000BASE-T ports, and 2 SFP ports. It has an integral AC supply (100 - 240V AC 50/60Hz 0.45A nominal). There is a console port which uses the H3C/Cisco pinout to provide RS232 on an 8P8C (RJ45) connector.

The 1920 8 port series all use single core 500 MHz MIPS-4KEc Realtek RTL83xx SoCs, have 32 MB of flash, and 128 MB of RAM.

All 1920 series switches are designed to occupy “1U” (1.75“ / 44.5mm) in a standard 19” equipment rack. All models have rack mount options, but the 8 port models have smaller (under 19“ wide) enclosures which may be useful for non-rack usage.

General info about OpenWRT on Realtek switch SoCs can be found on the wiki that OpenWRT developer Sander Vanheule maintains.

FIXME break the generic 1920 series info out in to a separate page, since so much info is shared between all models in this series.

Design Origins and Alternative Brandings

The software and hardware design of these switches appears to originate from 3Com (which was acquired by HP in 2010), rather than the “HP ProCurve” line of switches which run HP's own in-house embedded OS rather than Linux. The design and manufacturing was carried out by H3C (which was wholly owned by HP during this time, but was later sold off).

Older examples of these switches were manufactured before Hewlett Packard split into “consumer” and “enterprise” divisions. These carried the branding “HP 1920-8G Switch” and the same JG920A model number.

H3C also sold these switches under their own brand as the H3C S5110 switch series, with the S5110-28P-SI assumed to be equivalent to the JG924A.

FIXME

  1. The tables below are automatically generated, once the correct filters for Brand and Model are set.
  2. If the tables below show information for HPE 1920-8G (JG920A) HNGZA-HA0008, everything is OK and you can delete this text and the <WRAP> that encloses it.
  3. If the tables below contain “Nothing found”, it means that either
    1. the dataentry page for HPE 1920-8G (JG920A) HNGZA-HA0008 is missing. Please create a new dataentry page first, then reload this page. The tables should then contain $something. If they do, delete this text and the <WRAP> that encloses it.
    2. filters are not set correctly. Most common reason for “Nothing found”: The dataentry does not contain a Version, but we are filtering here for version → Please edit this section and adjust the filters with the proper Brand, Model and Version. In case the dataentry does not contain a version, delete the line filter : Versions~. Just try, it's easy. The tables should then contain $something. If they do, delete this text and the <WRAP> that encloses it.
  4. If the tables still contain “Nothing found”: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.

None at this time.

Install OpenWrt (generic explanation)

FIXME Please add the installation procedure here.

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

Specific values needed for tftp

tftp boot parameter defaults for JG920A and tftp boot example.

System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Press Ctrl+B to enter extended boot menu...
BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 3

==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Ethernet Parameter                                             |
|<0> Exit To Main Menu                                                     |
|<Ensure The Parameter Be Modified Before Downloading!>                    |
============================================================================
Enter your choice(0-5): 5

==========================<ETHERNET PARAMETER SET>==========================
|Note:       '.' = Clear field.                                            |
|            '-' = Go to previous field.                                   |
|          Ctrl+D = Quit.                                                  |
============================================================================
Protocol (FTP or TFTP) :tftp 
Load File Name         :host
                       :
Target File Name       :target
                       :
Server IP Address      :192.168.1.1 
Local IP Address       :192.168.1.253 
Gateway IP Address     :0.0.0.0 


==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash                                        |
|<1> Download Application Program To SDRAM And Run                         |
|<2> Update Main Application File                                          |
|<3> Update Backup Application File                                        |
|<4> Update Secure Application File                                        |
|<5> Modify Ethernet Parameter                                             |
|<0> Exit To Main Menu                                                     |
|<Ensure The Parameter Be Modified Before Downloading!>                    |
============================================================================
Enter your choice(0-5): 1
Loading.....................................................................
...............................Done!
4985736 bytes downloaded!
The App file is self-decompressing..........................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
..........Done!
System application is starting...

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address 192.168.1.1
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address 192.168.1.253

After doing sysupgrade from initramfs, bootloader config console example:

System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing..........................Done!

****************************************************************************
*                                                                          *
*            HPE 1920-8G Switch JG920A BootWare, Version 1.22              *
*                                                                          *
****************************************************************************
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date       : Apr 14 2017 15:05:19
CPU Type            : MIPS4kec
CPU L1 Cache        : 16KB
CPU Clock Speed     : 500MHz
Memory Type         : DDR3 SDRAM
Memory Size         : 128MB
Memory Speed        : 300MHz
BootWare Size       : 3MB
Flash Size          : 32MB


BootWare Validating...
Application program does not exist.
BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 4

===============================<File CONTROL>===============================
|Note:the operating device is flash                                        |
|<1> Display All File(s)                                                   |
|<2> Set Application File type                                             |
|<3> Set Configuration File type                                           |
|<4> Delete File                                                           |
|<0> Exit To Main Menu                                                     |
============================================================================
Enter your choice(0-4): 2

 'M' = MAIN      'B' = BACKUP      'S' = SECURE      'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B)   Time                 Type   Name                            |
|1   2399856   Jan/01/1970 00:00:00 N/A    openwrt-kernel.bin              |
|0   Exit                                                                  |
============================================================================
Enter file No:1

Modify the file attribute:
============================================================================
|<1> +Main                                                                 |
|<2> -Main                                                                 |
|<3> +Backup                                                               |
|<4> -Backup                                                               |
|<0> Exit                                                                  |
============================================================================
Enter your choice(0-4):1
This operation may take several minutes. Please wait....
Set the file attribute success!

===============================<File CONTROL>===============================
|Note:the operating device is flash                                        |
|<1> Display All File(s)                                                   |
|<2> Set Application File type                                             |
|<3> Set Configuration File type                                           |
|<4> Delete File                                                           |
|<0> Exit To Main Menu                                                     |
============================================================================
Enter your choice(0-4): 0

===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System                                                           |
|<2> Enter Serial SubMenu                                                  |
|<3> Enter Ethernet SubMenu                                                |
|<4> File Control                                                          |
|<5> Restore to Factory Default Configuration                              |
|<6> Skip Current System Configuration                                     |
|<7> BootWare Operation Menu                                               |
|<8> Clear Super Password                                                  |
|<9> Storage Device Operation                                              |
|<0> Reboot                                                                |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Enter your choice(0-9): 1
Starting to get the main application file--flash:/openwrt-kernel.bin!.......
...........
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
..............................................................Done!
System application is starting...

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

FIXME

  1. This table is automatically generated, once the correct filters for Brand and Model are set.
  2. If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
  3. If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for HPE 1920-8G (JG920A) HNGZA-HA0008? If not: Create one.
  4. If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
  5. If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for HPE 1920-8G (JG920A) HNGZA-HA0008
38400 , 8N1, RS232

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing..........................Done!

* * * HPE 1920-8G Switch JG920A BootWare, Version 1.22 * * * Copyright © 2010-2017 Hewlett Packard Enterprise Development LP

Compiled Date : Apr 14 2017 15:05:19 CPU Type : MIPS4kec CPU L1 Cache : 16KB CPU Clock Speed : 500MHz Memory Type : DDR3 SDRAM Memory Size : 128MB Memory Speed : 300MHz BootWare Size : 3MB Flash Size : 32MB

BootWare Validating... Press Ctrl+B to enter extended boot menu... Starting to get the main application file--flash:/target!................... ............................................................................ The main application file is self-decompressing............................. ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ............................................................................ ...Done! System application is starting... Startup configuration file does not exist. It will take a long time to get configuration file, please wait... Press CTRL_C to break

Retrieving configuration file failed!

Configuring default settings. User interface aux0 is available.

Press ENTER to get started.


[ 0.000000] Linux version 5.15.167 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 4 [ 0.000000] RTL838X model is 83806800 [ 0.000000] SoC Type: RTL8380 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019070 (MIPS 4KEc) [ 0.000000] MIPS: machine is HPE 1920-8G (JG920A) [ 0.000000] earlycon: ns16550a0 at MMIO 0x18002000 (options '38400n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using appended Device Tree. [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: earlycon [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 120624K/131072K available (6238K kernel code, 612K rwdata, 780K rodata, 1260K init, 219K bss, 10448K reserved, 0K cma) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] rtl83xx-clk: initialized, CPU 500 MHz, MEM 300 MHz (8 Bit DDR3), LXB 200 MHz [ 0.000000] clocksource: realtek_otto_timer: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 38225208801 ns [ 0.000005] sched_clock: 28 bits at 3125kHz, resolution 320ns, wraps every 42949672800ns [ 0.027186] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) [ 0.167688] pid_max: default: 32768 minimum: 301 [ 0.185412] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.209783] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.257318] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.290019] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.313017] pinctrl core: initialized pinctrl subsystem [ 0.334125] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.385749] rtl83xx-clk clock-controller: rate setting enabled, CPU 300-625 MHz, MEM 300-300 MHz, LXB 200-200 MHz, OVERCLOCK AT OWN RISK [ 0.431826] clocksource: Switched to clocksource realtek_otto_timer [ 0.456788] NET: Registered PF_INET protocol family [ 0.473660] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.500018] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.528232] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.554058] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.579607] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.603141] TCP: Hash tables configured (established 1024 bind 1024) [ 0.624929] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.646788] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.670993] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.701408] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.738223] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.757743] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.796432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.826153] pinctrl-single 1b001000.pinmux: 32 pins, size 4 [ 0.845720] pinctrl-single 1b00a000.pinmux: 32 pins, size 4 [ 0.866962] Probing RTL8231 GPIOs [ 0.878106] rtl8231_init called, MDIO bus ID: 0 [ 0.895636] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.925313] printk: console [ttyS0] disabled [ 0.939745] 18002000.uart: ttyS0 at MMIO 0x18002000 (irq = 31, base_baud = 12500000) is a 16550A [ 0.969059] printk: console [ttyS0] enabled [ 0.969059] printk: console [ttyS0] enabled [ 0.996830] printk: bootconsole [early0] disabled [ 0.996830] printk: bootconsole [early0] disabled [ 1.028068] printk: bootconsole [ns16550a0] disabled [ 1.028068] printk: bootconsole [ns16550a0] disabled [ 1.207385] brd: module loaded [ 1.229683] spi-nor spi0.0: mx25l25635e (32768 Kbytes) [ 1.246982] 8 fixed-partitions partitions found on MTD device spi0.0 [ 1.268224] OF: Bad cell count for /soc/spi@1200/flash@0/partitions [ 1.289177] OF: Bad cell count for /soc/spi@1200/flash@0/partitions [ 1.310563] Creating 8 MTD partitions on “spi0.0”: [ 1.326591] 0x000000000000-0x000000050000 : “bootware_basic” [ 1.353547] 0x000000060000-0x000000090000 : “bootware_data” [ 1.375664] 0x000000090000-0x0000000d0000 : “bootware_extend” [ 1.403321] 0x000000100000-0x000000150000 : “bootware_basic_backup” [ 1.427672] 0x000000160000-0x000000190000 : “bootware_data_backup” [ 1.456694] 0x000000190000-0x0000001d0000 : “bootware_extend_backup” [ 1.481511] 0x000000300000-0x000001ff0000 : “firmware” [ 1.507925] 2 h3c-vfs partitions found on MTD device firmware [ 1.527156] Creating 2 MTD partitions on “firmware”: [ 1.543740] 0x000000000000-0x000000260000 : “kernel” [ 1.566008] 0x000000260000-0x000001cf0000 : “rootfs” [ 1.585765] mtd: setting mtd8 (rootfs) as root device [ 1.605256] 1 squashfs-split partitions found on MTD device rootfs [ 1.625928] 0x000000510000-0x000001cf0000 : “rootfs_data” [ 1.649705] 0x000001ff0000-0x000002000000 : “factory” [ 1.696423] Probing RTL838X eth device pdev: 82099000, dev: 82099010 [ 1.768133] Found SoC ID: 8380: RTL8380, family 8380 [ 1.784868] rtl8380_init_mac [ 1.794537] Using MAC 0000000000010000 [ 1.924840] Realtek RTL8218B (internal) mdio-bus:08: Detected internal RTL8218B [ 1.949233] Firmware loaded. Size 1184, magic: 83808380 [ 4.514406] Realtek RTL8380 SERDES mdio-bus:18: Detected internal RTL8380 SERDES [ 4.539106] Firmware loaded. Size 1184, magic: 83808380 [ 4.556563] SDS power down value: 3 [ 4.592303] PLL control register: efffffff [ 4.605979] SDS power down value now: 3f [ 4.619062] Configuration of SERDES done [ 4.640485] i2c_dev: i2c /dev entries driver [ 4.663621] NET: Registered PF_INET6 protocol family [ 4.711688] Segment Routing with IPv6 [ 4.724200] In-situ OAM (IOAM) with IPv6 [ 4.737640] NET: Registered PF_PACKET protocol family [ 4.754681] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you nee. [ 4.799158] 8021q: 802.1Q VLAN Support v1.8 [ 4.816029] i2c-gpio i2c-gpio-0: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 4.844375] i2c-gpio i2c-gpio-0: using lines 474 (SDA) and 475 (SCL) [ 4.866303] i2c-gpio i2c-gpio-1: Slow GPIO pins might wreak havoc into I2C/SMBus bus timing [ 4.894650] i2c-gpio i2c-gpio-1: using lines 464 (SDA) and 465 (SCL) [ 4.918142] sfp sfp-0: Host maximum power 1.0W [ 4.933055] sfp sfp-0: No tx_disable pin: SFP modules will always be emitting. [ 4.959231] sfp sfp-1: Host maximum power 1.0W [ 4.974151] sfp sfp-1: No tx_disable pin: SFP modules will always be emitting. [ 5.060202] Realtek RTL8218B (internal) rtl838x slave mii-0:08: Detected internal RTL8218B [ 5.087752] Firmware loaded. Size 1184, magic: 83808380 [ 7.657480] Realtek RTL8380 SERDES rtl838x slave mii-0:18: Detected internal RTL8380 SERDES [ 7.685332] Firmware loaded. Size 1184, magic: 83808380 [ 7.702833] SDS power down value: 3 [ 7.738547] PLL control register: f [ 7.750242] SDS power down value now: 3f [ 7.763374] Configuration of SERDES done [ 7.807921] In rtl83xx_vlan_setup [ 7.819087] UNKNOWN_MC_PMASK: 000000001fffffff [ 7.833921] VLAN profile 0: L2 learning: 1, UNKN L2MC FLD PMSK 511, UNKN IPMC FLD PMSK 511, UNKN IPv6MC FLD PMSK: 511 [ 8.871972] rtl83xx_enable_phy_polling: 500ff00 [ 9.992533] rtl83xx-switch switch@1b000000: configuring for fixed/internal link mode [ 10.019242] rtl83xx-switch switch@1b000000: Link is Up - 1Gbps/Full - flow control off [ 10.046609] rtl83xx-switch switch@1b000000 lan1 (uninitialized): PHY [mdio-bus:08] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.089629] rtl83xx-switch switch@1b000000 lan2 (uninitialized): PHY [mdio-bus:09] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.135763] rtl83xx-switch switch@1b000000 lan3 (uninitialized): PHY [mdio-bus:0a] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.178529] rtl83xx-switch switch@1b000000 lan4 (uninitialized): PHY [mdio-bus:0b] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.224996] rtl83xx-switch switch@1b000000 lan5 (uninitialized): PHY [mdio-bus:0c] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.268015] rtl83xx-switch switch@1b000000 lan6 (uninitialized): PHY [mdio-bus:0d] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.314222] rtl83xx-switch switch@1b000000 lan7 (uninitialized): PHY [mdio-bus:0e] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.357188] rtl83xx-switch switch@1b000000 lan8 (uninitialized): PHY [mdio-bus:0f] driver [Realtek RTL8218B (internal)] (irq=POLL) [ 10.404033] DSA: tree 0 setup [ 10.414085] LINK state irq: 20 [ 10.424383] In rtl83xx_setup_qos [ 10.435170] Setting up RTL838X QoS [ 10.446512] RTL838X_PRI_SEL_TBL_CTRL(i): 00033112 [ 10.462226] Current Intprio2queue setting: 00000000 [ 10.478488] QM_PKT2CPU_INTPRI_MAP: 00fac688 [ 10.492715] rtl838x_dbgfs_init called [ 10.507788] rtl83xx_fib_event_work_do: FIB4 default rule failed [ 10.534208] rtl83xx_fib_event_work_do: FIB4 default rule failed [ 10.559821] clk: Disabling unused clocks [ 10.588608] VFS: Mounted root (squashfs filesystem) readonly on device 31:8. [ 10.626068] Freeing unused kernel image (initmem) memory: 1260K [ 10.645841] This architecture does not have kernel memory protection. [ 10.667311] Run /sbin/init as init process [ 10.680993] with arguments: [ 10.690919] /sbin/init [ 10.699980] with environment: [ 10.710468] HOME=/ [ 10.718403] TERM=linux [ 11.512619] init: Console is alive [ 11.525232] init: - watchdog - [ 12.090880] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 12.167874] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 12.203087] init: - preinit - [ 13.917575] random: jshn: uninitialized urandom read (4 bytes read) [ 14.140225] random: jshn: uninitialized urandom read (4 bytes read) [ 14.543094] RTL8380 Link change: status: 1, ports 100 [ 15.013438] random: jshn: uninitialized urandom read (4 bytes read) [ 15.128826] random: jshn: uninitialized urandom read (4 bytes read) [ 15.287466] random: jshn: uninitialized urandom read (4 bytes read) [ 16.456016] RESETTING 8380, CPU_PORT 28 [ 16.669584] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 16.696400] In rtl838x_mac_config, mode 1 [ 16.712911] rtl83xx-switch switch@1b000000 lan1: configuring for phy/internal link mode [ 16.739780] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 16.767952] 8021q: adding VLAN 0 to HW filter on device lan1 [ 16.787624] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.808602] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 16.830538] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 16.894868] rtl83xx_fib_event_work_do: FIB4 failed [ 16.910891] RTL8380 Link change: status: 1, ports 100 [ 16.967383] rtl83xx_fib_event_work_do: FIB4 failed [ 17.009252] rtl83xx_fib_event_work_do: FIB4 failed Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 18.151962] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 19.430579] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 19.463176] urandom-seed: Seed file not found (/etc/urandom.seed) [ 19.639680] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 19.672075] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 19.713272] rtl83xx_fib4_del: no such gateway: 0.0.0.0 [ 19.745933] procd: - early - [ 19.756263] procd: - watchdog - [ 20.732125] procd: - watchdog - [ 20.744197] procd: - ubus - [ 20.858170] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.883021] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.905367] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.934362] procd: - init - Please press Enter to activate this console. [ 22.618665] random: jshn: uninitialized urandom read (4 bytes read) [ 22.742681] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.888280] kmodloader: loading kernel modules from /etc/modules.d/* [ 23.018230] GACT probability on [ 23.054208] Mirror/redirect action on [ 23.119605] u32 classifier [ 23.128744] input device check on [ 23.140971] Actions configured [ 23.563761] kmodloader: done loading kernel modules from /etc/modules.d/* [ 25.642656] urngd: v1.0.2 started. [ 29.012546] random: crng init done [ 29.023942] random: 23 urandom warning(s) missed due to ratelimiting [ 33.270814] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 83.223325] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 83.377539] in rtl838x_eth_stop [ 83.388206] rtl838x-eth 1b00a300.ethernet eth0: Link is Down [ 83.947527] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 83.969417] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 83.991274] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 84.013117] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 85.253734] Using MAC <redacted> [ 85.325793] RESETTING 8380, CPU_PORT 28 [ 85.539369] rtl838x-eth 1b00a300.ethernet eth0: configuring for fixed/internal link mode [ 85.566184] In rtl838x_mac_config, mode 1 [ 85.580030] rtl838x-eth 1b00a300.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 85.608363] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 85.629400] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 85.651312] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 86.065997] device eth0 entered promiscuous mode [ 86.081522] rtl83xx-switch switch@1b000000 lan1: configuring for phy/internal link mode [ 86.209807] 8021q: adding VLAN 0 to HW filter on device lan1 [ 86.413234] switch: port 1(lan1) entered blocking state [ 86.430712] switch: port 1(lan1) entered disabled state [ 86.449049] device lan1 entered promiscuous mode [ 86.725403] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 86.834418] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 87.483716] rtl83xx-switch switch@1b000000 lan2: configuring for phy/internal link mode [ 87.572297] 8021q: adding VLAN 0 to HW filter on device lan2 [ 87.591760] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 87.613733] rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported [ 87.703283] switch: port 2(lan2) entered blocking state [ 87.720769] switch: port 2(lan2) entered disabled state [ 87.824614] device lan2 entered promiscuous mode [ 88.267382] rtl83xx-switch switch@1b000000 lan3: configuring for phy/internal link mode [ 88.405888] 8021q: adding VLAN 0 to HW filter on device lan3 [ 88.518465] switch: port 3(lan3) entered blocking state [ 88.535960] switch: port 3(lan3) entered disabled state [ 88.692236] device lan3 entered promiscuous mode [ 89.065502] rtl83xx-switch switch@1b000000 lan4: configuring for phy/internal link mode [ 89.124774] RTL8380 Link change: status: 1, ports 100 [ 89.158784] 8021q: adding VLAN 0 to HW filter on device lan4 [ 89.256005] switch: port 4(lan4) entered blocking state [ 89.273462] switch: port 4(lan4) entered disabled state [ 89.372260] device lan4 entered promiscuous mode [ 89.595251] rtl83xx-switch switch@1b000000 lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 89.623712] switch: port 1(lan1) entered blocking state [ 89.641192] switch: port 1(lan1) entered forwarding state [ 89.832464] IPv6: ADDRCONF(NETDEV_CHANGE): switch: link becomes ready [ 89.883107] RTL8380 Link change: status: 1, ports 100 [ 89.900107] rtl83xx-switch switch@1b000000 lan1: Link is Down [ 89.920140] rtl83xx-switch switch@1b000000 lan5: configuring for phy/internal link mode [ 89.971988] rtl83xx-switch switch@1b000000 lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 90.022240] 8021q: adding VLAN 0 to HW filter on device lan5 [ 90.041531] IPv6: ADDRCONF(NETDEV_CHANGE): switch.1: link becomes ready [ 90.113293] switch: port 5(lan5) entered blocking state [ 90.130766] switch: port 5(lan5) entered disabled state [ 90.149128] device lan5 entered promiscuous mode [ 90.593352] rtl83xx-switch switch@1b000000 lan6: configuring for phy/internal link mode [ 90.685076] 8021q: adding VLAN 0 to HW filter on device lan6 [ 90.708589] rtl83xx-switch switch@1b000000 lan1: Link is Down [ 90.728605] switch: port 1(lan1) entered disabled state [ 90.816307] switch: port 6(lan6) entered blocking state [ 90.833781] switch: port 6(lan6) entered disabled state [ 90.852284] device lan6 entered promiscuous mode [ 91.252418] rtl83xx-switch switch@1b000000 lan7: configuring for phy/internal link mode [ 91.342229] 8021q: adding VLAN 0 to HW filter on device lan7

[ 91.457973] switch: port 7(lan7) entered blocking state [ 91.475445] switch: port 7(lan7) entered disabled state [ 91.493888] device lan7 entered promiscuous mode

BusyBox v1.36.1 (2024-09-23 12:34:46 UTC) built-in shell (ash)

_______                     ________        __

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -| || | | || _|| _| |_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

----------------------------------------------------- OpenWrt 23.05.5, r24106-10cc5fcd00


WARNING!

There is no root password defined on this device! Use the “passwd” command to set up a new password in order to prevent unauthorized SSH logins.


root@OpenWrt:/#


Space for additional notes, links to forum threads or other resources.

  • ...

FIXME Add tags below, then remove this fixme.

How to add tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2025/01/24 06:27
  • by evs