Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
| toh:gl-inet:installation [2018/06/17 12:03] – Section heading levels corrected tmomas | toh:gl.inet:installation [2019/10/12 09:07] – tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | All GL-inet devices share the same general installation instructions as they all have a firmware based on OpenWrt, and all have a uboot bootloader with web interface to upload a new firmware. | + | All GL.inet devices share the same general installation instructions as they all have a firmware based on OpenWrt, and all have a uboot bootloader with web interface to upload a new firmware. |
| ===== Normal upgrade ===== | ===== Normal upgrade ===== | ||
| Line 8: | Line 8: | ||
| ===== uBoot upgrade ===== | ===== uBoot upgrade ===== | ||
| - | This applies to all GLI routers, including 6416, AR150, AR300, MT300A, MT300N, MT750, Domino boards and newer products.\\ | + | This applies to all GL.inet |
| This method can be used also as a recovery system if you brick the device.\\ | This method can be used also as a recovery system if you brick the device.\\ | ||
| According to the link provided in the upgrade web page, it is based off [[https:// | According to the link provided in the upgrade web page, it is based off [[https:// | ||
| Line 15: | Line 15: | ||
| - Press and hold the Reset button firmly first, and then power on your device. Must obey the first and then procedure. | - Press and hold the Reset button firmly first, and then power on your device. Must obey the first and then procedure. | ||
| - The LEDs will start blinking. Release your finger when you see the LEDs flashing 5 times for AR150 and 6416 ( flashing 3 times for MT300N and MT300A). Number of blinking to count for newer devices (tested on a BL-1300) seems to be 5, and after that it stops blinking. | - The LEDs will start blinking. Release your finger when you see the LEDs flashing 5 times for AR150 and 6416 ( flashing 3 times for MT300N and MT300A). Number of blinking to count for newer devices (tested on a BL-1300) seems to be 5, and after that it stops blinking. | ||
| - | - Set your computer’s IP address to 192.168.1.2 {{:toh:gl-inet: | + | - Set your computer’s IP address to 192.168.1.2\\ {{media:gl.inet: |
| - | - User Firefox or Chrome to visit http:// | + | - User Firefox or Chrome to visit '' |
| - | - Read the instructions on the web UI, it may tell you that the file should have some word in the name to be accepted. (the BL-1300 wanted either " | + | - Read the instructions on the web UI, it may tell you that the file should have some word in the name to be accepted (the BL-1300 wanted either " |
| - Wait for around 3 minutes. Don’t power off your device while upgrading or you will have to repeat this procedure. | - Wait for around 3 minutes. Don’t power off your device while upgrading or you will have to repeat this procedure. | ||
| - | The following screenshot is an example of the uboot web UI from a GL.iNet BL-1300 {{: | ||
| ===== Official guides ===== | ===== Official guides ===== | ||
| - | At the following | + | At the following |
| - | [[https://www.gl-inet.com/ | + | [[https://docs.gl-inet.com/ |
| - | [[https://www.gl-inet.com/uboot-flashing/]] | + | |