Show pagesourceOld revisionsBacklinksBack to top × Table of Contents GL.iNet VIXMINI / microuter-N300 Supported Versions Experimental Versions Hardware Highlights Installation Flash Layout OEM easy installation OEM installation using the TFTP method Upgrading OpenWrt LuCI Web Upgrade Process Terminal Upgrade Process Debricking Failsafe mode Basic configuration Specific Configuration Network interfaces Switch Ports (for VLANs) Buttons Hardware Info Photos Opening the case Serial JTAG Bootloader mods Hardware mods Bootlogs OEM bootlog OpenWrt bootlog Notes Tags GL.iNet VIXMINI / microuter-N300 Under Construction! This page is currently under construction. You can edit the article to help completing it. VIXMINI is a small, light and portable wireless router. MTK7628NN@580MHz, 1 x WAN/LAN port,64MB ram / 8MB flash. microuter-N300 have same fcc id with VIXMINI, come with 128MB ram / 16MB flash. Support Forums https://forum.openwrt.org/t/gl-inet-microuter-n300-support Supported Versions BrandModelVersionCurrent ReleaseOEM InfoForum SearchTechnical DataGL.iNetVIXMINI19.07.7https://store.gl-inet.com/products/vixmini-mini-travel-routerVIXMINIView/Edit dataBrandModelVersionCurrent ReleaseOEM InfoForum SearchTechnical DataGL.iNetmicrouter-N300snapshothttp://¿microuter-N300View/Edit dataUnsupported Functions Experimental Versions None at this time. Hardware Highlights ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBVIXMINIMediaTek MT7628NN580864MediaTek MT7628NNb/g/n-1--1x µUSB (power)ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBmicrouter-N300MediaTek MT7628NN58016128MT7628NNb/g/n¿1¿¿¿ Installation ModelVersionCurrent ReleaseFirmware OpenWrt InstallFirmware OpenWrt UpgradeFirmware OEM StockVIXMINI19.07.7http://-http://downloads.openwrt.org/releases/19.07.7/targets/ramips/mt76x8/openwrt-19.07.7-ramips-mt76x8-glinet_vixmini-squashfs-sysupgrade.bin ModelVersionCurrent ReleaseFirmware OpenWrt snapshot InstallFirmware OpenWrt snapshot UpgradeFirmware OEM Stockmicrouter-N300snapshothttps://downloads.openwrt.org/snapshots/targets/ramips/mt76x8/openwrt-ramips-mt76x8-glinet_microuter-n300-initramfs-kernel.binhttps://downloads.openwrt.org/snapshots/targets/ramips/mt76x8/openwrt-ramips-mt76x8-glinet_microuter-n300-squashfs-sysupgrade.binhttp://¿ → Install OpenWrt (generic explanation) Please add the installation procedure here. Flash Layout Find out flash layout, then add the flash layout table here (copy, paste, modify the example). Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout. OEM easy installation The instructions below are for Broadcom devices and only serve as an example. Remove / modify them if they do not apply to this particular device! This section deals with How you install OpenWrt from a device freshly opened The steps required such as reset to factory defaults if the device has already been configured Note: Reset router to factory defaults if it has been previously configured. Browse to http://192.168.1.1/Upgrade.asp Upload .bin file to router Wait for it to reboot Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed. OEM installation using the TFTP method → generic.flashing.tftp Specific values needed for tftp Enter values for “FILL-IN” below Bootloader tftp server IPv4 address FILL-IN Bootloader MAC address (special) FILL-IN Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”) TFTP transfer window FILL-IN seconds TFTP window start approximately FILL-IN seconds after power on TFTP client required IP address FILL-IN Upgrading OpenWrt → generic.sysupgrade These are generic instructions. Update with your router's specifics. LuCI Web Upgrade Process Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL Upload image file for sysupgrade to LuCI Wait for reboot Terminal Upgrade Process If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading: sysupgrade mtd Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. sysupgrade Login as root via SSH on 192.168.1.1, then enter the following commands: cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc mtd If sysupgrade does not support this router, use mtd. Login as root via SSH on 192.168.1.1, then enter the following commands: cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot Debricking → generic.debrick Failsafe mode → failsafe_and_factory_reset Basic configuration → Basic configuration After flashing, proceed with this. Set up your Internet connection, configure wireless, configure USB port, etc. Specific Configuration Please fill in real values for this device, then remove the EXAMPLEs Network interfaces The default network configuration is: Interface Name Description Default configuration br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24 vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP wl0 EXAMPLE WiFi EXAMPLE Disabled Switch Ports (for VLANs) Please fill in real values for this device, then remove the EXAMPLEs Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. Port Switch port Internet (WAN) EXAMPLE 4 LAN 1 EXAMPLE 3 LAN 2 EXAMPLE 2 LAN 3 EXAMPLE 1 LAN 4 EXAMPLE 0 Buttons → hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto. Please fill in real values for this device, then remove the EXAMPLEs The GL.iNet VIXMINI has the following buttons: BUTTON Event EXAMPLE Reset reset EXAMPLE Secure Easy Setup ses EXAMPLE No buttons at all. - Hardware Info This table is automatically generated, once the correct filters for Brand and Model are set. If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy. If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for GL.iNet VIXMINI ? If not: Create one. If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it. If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help. —- datatemplatelist dttpllist —- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=GL.iNet filter : Model=VIXMINI filter : Versions= Photos Front: Insert photo of front of the casing Back: Insert photo of back of the casing Backside label: Insert photo of backside label Opening the case Note: This will void your warranty! Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, … To remove the cover and open the device, do a/b/c Main PCB: Insert photo of PCB Serial → port.serial general information about the serial port, serial port cable, etc. How to connect to the Serial Port of this specific device: Insert photo of PCB with markings for serial port Replace EXAMPLE by real values. Serial connection parameters for GL.iNet VIXMINI @@Version@@ EXAMPLE 115200, 8N1 JTAG → port.jtag general information about the JTAG port, JTAG cable, etc. How to connect to the JTAG Port of this specific device: Insert photo of PCB with markings for JTAG port Bootloader mods → bootloader Hardware mods None so far. Bootlogs OEM bootlog COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE OpenWrt bootlog COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING Notes Space for additional notes, links to forum threads or other resources. … Tags Add tags below, then remove this fixme. How to add tags EXAMPLETAG This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies EXAMPLETAG Last modified: 2020/12/21 08:14by lessload