User Tools

Site Tools


toh:engenius:esr-6650

Senao/EnGenius ESR-6650

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device will end after 2019.
19.07 will be the last official build for 4/32 devices. After 19.07, no further OpenWrt images will be built for 4/32 devices. See OpenWrt on 4/32 devices what you can do now.

Built by Senao Networks, this router is made to serve as a 3G gateway. It is sold under many names, including EnGenius ESR-6650 and Encore ENHWI-3GN3.

Supported Versions

Hardware Highlights

Installation

Board Pictures

Serial Port

o 3.3v
o GND
o TX
o RX

57600 baud, 8n1

Bootlog

OpenWrt Bootlog (Barrier Breaker rc1 (r41580))

U-boot Ver:1.0.1.1 2009/09/25 Board: Ralink APSoC DRAM: 32 MB 1*32 MB ============================================ ASIC 3052_MP2 (Port5<->None) Product Name: ESR-6650 SDRAM CAS = 3(d1835272) ============================================ Please choose the operation: 1: Load system code to SDRAM via TFTP. [ 0.000000] Linux version 3.10.44 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41580) ) #2 Sat Jul 12 19:13:26 CEST 2014 [ 0.000000] SoC Type: Ralink RT3350 id:1 rev:2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is Senao / EnGenius ESR-9753 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00058d00 [ 0.000000] Readback ErrCtl register=00058d00 [ 0.000000] Memory: 29160k/32768k available (2282k kernel code, 3608k reserved, 567k data, 220k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 320MHz [ 0.000000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] pinctrl core: initialized pinctrl subsystem [ 0.100000] NET: Registered protocol family 16 [ 0.150000] bio: create slab <bio-0> at 0 [ 0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.170000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.180000] Switching to clocksource MIPS [ 0.190000] NET: Registered protocol family 2 [ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.230000] TCP: Hash tables configured (established 512 bind 512) [ 0.240000] TCP: reno registered [ 0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.270000] NET: Registered protocol family 1 [ 0.280000] rt-timer 10000100.timer: maximum frequncy is 6510Hz [ 0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.380000] msgmni has been set to 56 [ 0.380000] io scheduler noop registered [ 0.390000] io scheduler deadline registered (default) [ 0.410000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.440000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.450000] console [ttyS0] enabled, bootconsole disabled [ 0.450000] console [ttyS0] enabled, bootconsole disabled [ 0.480000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a7 [ 0.500000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.510000] Amd/Fujitsu Extended Query version 1.1. [ 0.520000] 1f000000.cfi: Swapping erase regions for top-boot CFI table. [ 0.530000] number of CFI chips: 1 [ 0.540000] 4 ofpart partitions found on MTD device 1f000000.cfi [ 0.550000] Creating 4 MTD partitions on "1f000000.cfi": [ 0.570000] 0x000000000000-0x000000030000 : "u-boot" [ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.590000] 0x000000040000-0x000000050000 : "factory" [ 0.610000] 0x000000050000-0x000000400000 : "firmware" [ 0.620000] 0x00000014e22b-0x000000400000 : "rootfs" [ 0.630000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.660000] mtd: device 4 (rootfs) set to be root filesystem [ 0.670000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x90000 [ 0.690000] 0x000000370000-0x000000400000 : "rootfs_data" [ 0.720000] eth0: done loading [ 0.730000] rt2880_wdt 10000120.watchdog: Initialized [ 0.740000] TCP: cubic registered [ 0.750000] NET: Registered protocol family 17 [ 0.760000] Bridge firewalling registered [ 0.770000] 8021q: 802.1Q VLAN Support v1.8 [ 0.790000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.800000] Freeing unused kernel memory: 220K (802c9000 - 80300000) procd: Console is alive procd: - watchdog - [ 3.760000] usbcore: registered new interface driver usbfs [ 3.770000] usbcore: registered new interface driver hub [ 3.790000] usbcore: registered new device driver usb [ 3.810000] dwc_otg: version 2.72a 24-JUN-2008 [ 3.830000] leds-gpio gpio-leds.3: pins are not configured from the driver procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready jffs2 is ready [ 8.380000] jffs2: notice: (291) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (1 unchecked, 18 orphan) and 237 of xref (0 dead, 18 orphan) found. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 10.870000] NET: Registered protocol family 10 [ 10.900000] nf_conntrack version 0.5.0 (459 buckets, 1836 max) [ 10.920000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.950000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 10.970000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 10.990000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.080000] xt_time: kernel timezone is -0000 [ 11.190000] cfg80211: Calling CRDA to update world regulatory domain [ 11.210000] cfg80211: World regulatory domain updated: [ 11.220000] cfg80211: DFS Master region: unset [ 11.230000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.250000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.270000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.280000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.300000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 11.310000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.330000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.350000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.360000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.400000] PPP generic driver version 2.4.2 [ 11.430000] NET: Registered protocol family 24 [ 11.510000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 11.520000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. [ 11.550000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected [ 11.560000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected [ 20.740000] device eth0.1 entered promiscuous mode [ 20.750000] device eth0 entered promiscuous mode [ 20.770000] br-lan: port 1(eth0.1) entered forwarding state [ 20.780000] br-lan: port 1(eth0.1) entered forwarding state [ 22.780000] br-lan: port 1(eth0.1) entered forwarding state procd: - init complete - BusyBox v1.22.1 (2014-07-11 15:16:08 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (14.07-rc1, r41580) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/engenius/esr-6650.txt · Last modified: 2019/02/12 21:21 by tmomas