Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
inbox:engenius:engenius_ecb9500 [2018/03/04 10:10] bobafetthotmailtoh:engenius:engenius_ecb9500 [2018/04/13 07:06] – link updated tmomas
Line 53: Line 53:
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
 ===== Installation ===== ===== Installation =====
-  - → [[downloads|Obtain firmware]] +  - → [[:downloads|Obtain firmware]] 
-  - → [[doc:howto:generic.flashing|Install OpenWrt]] +  - → [[docs:guide-user:installation:generic.flashing|Install OpenWrt]] 
-  - → [[downloads|Latest OpenWrt release]]+  - → [[:downloads|Latest OpenWrt release]]
  
 ==== Installing OpenWrt ==== ==== Installing OpenWrt ====
Line 63: Line 63:
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
 ===== Debricking ===== ===== Debricking =====
--> [[doc:howto:generic.debrick]]+-> [[docs:guide-user:troubleshooting:generic.debrick]]
 ***/ ***/
  
Line 69: Line 69:
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
 ===== Failsafe mode ===== ===== Failsafe mode =====
--> [[doc:howto:generic.failsafe]]+-> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset]]
 ***/ ***/
  
Line 75: Line 75:
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
 ===== Basic configuration ===== ===== Basic configuration =====
-After flashing, proceed with [[doc:howto:basic.config|Basic configuration]]: Set up your Internet connection, configure wireless, configure USB port, etc.+After flashing, proceed with [[docs:guide-user:base-system:start|Basic configuration]]: Set up your Internet connection, configure wireless, configure USB port, etc.
 ***/ ***/
  
Line 98: Line 98:
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
 ==== Buttons ==== ==== Buttons ====
--> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s).+-> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s).
 Here, we merely name the buttons, so we can use them in the above Howto. Here, we merely name the buttons, so we can use them in the above Howto.
  
Line 134: Line 134:
 ==== Flash Layout ==== ==== Flash Layout ====
 <WRAP BOX> <WRAP BOX>
-FIXME //[[:doc:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[doc:techref:flash.layout#partitioning_of_squashfs-images|example]]).//+FIXME //[[:docs:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[docs:techref:flash.layout#partitioning_of_squashfs-images|example]]).//
  
-Please check out the article [[doc:techref:Flash.Layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout.+Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout.
 </WRAP> </WRAP>
 ***/ ***/
Line 162: Line 162:
  
 ==== Serial ==== ==== Serial ====
--> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc.+-> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
  
 How to connect to the serial port of this specific device: ((via [[https://wikidevi.com/wiki/EnGenius_ECB9500|wikidevi]] link [[https://apps.fcc.gov/eas/GetApplicationAttachment.html?id=1135191|to fcc docs]] and inspection of real hw))pinout is silkscreened about .75 cm next to 6 pin serial header. From left to right (front to back of device): 1. P3V3 (power) 2. GND (ground) 3. TXD (from device) 4. RXD (to device) 5. CTS 6. RTS. How to connect to the serial port of this specific device: ((via [[https://wikidevi.com/wiki/EnGenius_ECB9500|wikidevi]] link [[https://apps.fcc.gov/eas/GetApplicationAttachment.html?id=1135191|to fcc docs]] and inspection of real hw))pinout is silkscreened about .75 cm next to 6 pin serial header. From left to right (front to back of device): 1. P3V3 (power) 2. GND (ground) 3. TXD (from device) 4. RXD (to device) 5. CTS 6. RTS.
Line 173: Line 173:
  
 ==== JTAG ==== ==== JTAG ====
--> [[doc:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.+-> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
  
 How to connect to the JTAG Port of this specific device:\\ How to connect to the JTAG Port of this specific device:\\
  • Last modified: 2019/10/08 16:36
  • by tmomas