Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| inbox:engenius:engenius_ecb9500 [2018/03/04 10:05] – bobafetthotmail | toh:engenius:engenius_ecb9500 [2019/10/08 16:36] (current) – [Info] common format for hardware info applied tmomas | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ~~NOTOC~~ | ~~NOTOC~~ | ||
| - | /* This template is intended to be used via https://wiki.openwrt.org/ | + | /* This template is intended to be used via https:// |
| - | | {{page> | + | {{page> |
| //Seems that the same (or very similar) device has also been sold as ECB9750// | //Seems that the same (or very similar) device has also been sold as ECB9750// | ||
| /*****/ | /*****/ | ||
| - | /* How to add images ========> | + | /* How to add images ========> |
| /*****/ | /*****/ | ||
| Line 17: | Line 17: | ||
| ===== OpenWrt support ===== | ===== OpenWrt support ===== | ||
| - | **WIP** | + | <color red>**WIP**</ |
| - | The hardware seems to be supportable; | + | The hardware seems to be supportable; |
| See https:// | See https:// | ||
| Line 53: | Line 53: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | - → [[downloads|Obtain firmware]] | + | - → [[:downloads|Obtain firmware]] |
| - | - → [[doc:howto: | + | - → [[docs:guide-user: |
| - | - → [[about:latest|Latest OpenWrt release]] | + | - → [[:downloads|Latest OpenWrt release]] |
| ==== Installing OpenWrt ==== | ==== Installing OpenWrt ==== | ||
| Line 63: | Line 63: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| ***/ | ***/ | ||
| Line 69: | Line 69: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Failsafe mode ===== | ===== Failsafe mode ===== | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ***/ | ***/ | ||
| Line 75: | Line 75: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Basic configuration ===== | ===== Basic configuration ===== | ||
| - | After flashing, proceed with [[doc:howto:basic.config|Basic configuration]]: | + | After flashing, proceed with [[docs:guide-user:base-system: |
| ***/ | ***/ | ||
| Line 98: | Line 98: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| Here, we merely name the buttons, so we can use them in the above Howto. | Here, we merely name the buttons, so we can use them in the above Howto. | ||
| Line 116: | Line 116: | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| ==== Info ==== | ==== Info ==== | ||
| - | | **Architecture:** | MIPS | + | ^ Architecture |
| - | | **Vendor:** | Ralink | + | ^ Vendor |
| - | | **Bootloader:** | U-Boot | + | ^ Bootloader |
| - | | **System-On-Chip:** | Ralink RT2880 - MIPS 4KEc | + | ^ System-On-Chip |
| - | | **CPU/Speed** | 266 MHz | | + | ^ CPU/ |
| - | | **Flash-Chip:** | ST M29W640GT | + | ^ Flash-Chip |
| - | | **Flash size:** | 8 MiB | | + | ^ Flash size | 8 MiB | |
| - | | **RAM:** | + | ^ RAM |
| - | | **Wireless:** | RT2820 2.4GHz 802.11bgn | + | ^ Wireless |
| - | | **Ethernet:** | 10/100/1000 Mbit/s (w/ vlan support? | + | ^ Ethernet |
| - | | **USB:** | + | ^ USB |
| - | | **Serial:** | [[# | + | ^ Serial |
| - | | **JTAG:** | [[# | + | ^ JTAG | [[# |
| Line 134: | Line 134: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME //[[:doc: | + | FIXME //[[:docs: |
| - | Please check out the article [[doc:techref:Flash.Layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout. | + | Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout. |
| </ | </ | ||
| ***/ | ***/ | ||
| Line 162: | Line 162: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the serial port of this specific device: ((via [[https:// | How to connect to the serial port of this specific device: ((via [[https:// | ||
| Line 173: | Line 173: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the JTAG Port of this specific device:\\ | How to connect to the JTAG Port of this specific device:\\ | ||
| Line 322: | Line 322: | ||
| <WRAP bootlog> | <WRAP bootlog> | ||
| < | < | ||
| - | |||
| U-Boot 1.1.3 (Nov 20 2008 - 18:00:37) | U-Boot 1.1.3 (Nov 20 2008 - 18:00:37) | ||
| Line 591: | Line 590: | ||
| ===== Tags ===== | ===== Tags ===== | ||
| - | |||
| [[meta: | [[meta: | ||
| - | {{tag> | + | {{tag> |