ELECOM WRC-1167GST2

The Elecom WRC-1167GST2 is a dual-band IEEE 802.11ac router based on MediaTek MT7621AT and MediaTek MT7615DN. It has 5 gigabit ethernet ports, 32MB flash and 256MB DDR3L RAM.

Elecom WRC-1167GST2

ModelSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
WRC-1167GST2MediaTek MT7621A88032256MediaTek MT7615Db/g/na/n/ac-5--

generic.sysupgrade Upgrading via luci and command line (ssh) is both supported.

generic.debrick

The bootloader seems to allow loading and flashing code via tftp. This can be triggered via serial connection, see bootlog for details of which options the bootloader provides.

failsafe_and_factory_reset

Failsafe mode will disable wifi and have lan connectivity only on port lan 1, the one farthest away from wan.

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

General
Brand ELECOM
Model WRC-1167GST2
Versions
Device Type WiFi Router
Availability Available 2021
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=7ba2f5c96f2697e828c28bf2daf2e4978e950207
Supported Since Release 21.02.0
Supported Current Release 21.02.3
Unsupported
Hardware
Bootloader ¿
Target ramips
System-On-Chip MediaTek MT7621A
CPU MHz 880
Flash MB 32
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch MediaTek MT7621A
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware MediaTek MT7615D
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count 6
Button count 3
Power supply 12 VDC, 1.0 A
Links
Forum Topic URL
WikiDevi URL
OEM device homepage URL https://www.elecom.co.jp/products/WRC-1167GST2.html
Firmware OEM Stock URL https://www.elecom.co.jp/support/download/network/wireless_lan/wrc-1167gst2/
Firmware OpenWrt Install URL https://downloads.openwrt.org/releases/21.02.3/targets/ramips/mt7621/openwrt-21.02.3-ramips-mt7621-elecom_wrc-1167gst2-squashfs-factory.bin
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/releases/21.02.3/targets/ramips/mt7621/openwrt-21.02.3-ramips-mt7621-elecom_wrc-1167gst2-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Front:
front

Back:
back

Backside label:
label

Note: This will void your warranty!

There are four torx screws (with security pin) below the four rubber feet. Once the screws are removed the case is still held together by plastic clips. Those can be overcome by carefully prying open the case.

Main PCB:
pcb
backside:
pcb

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
serial Note: serial port is 3.3V

Serial connection parameters
for ELECOM WRC-1167GST2
57600 / 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
JTAG header not found, see photos of pcb

None so far.

=================================================================== MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL2 FB_DL: 0xc, 1/0 = 662/362 31000000 PLL4 FB_DL: 0x10, 1/0 = 547/477 41000000 PLL3 FB_DL: 0x16, 1/0 = 602/422 59000000 do DDR setting..[01F40000] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 000F:| 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 64 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001F21 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 8 9 12 11 8 12 8 7 10 10 | 9 12 9 12 9 11 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =33 DQS1 = 31 ================================================================== bit DQS0 bit DQS1 0 (1~61)31 8 (1~58)29 1 (0~61)30 9 (1~58)29 2 (1~62)31 10 (1~61)31 3 (1~65)33 11 (1~61)31 4 (1~65)33 12 (1~62)31 5 (0~61)30 13 (1~61)31 6 (1~64)32 14 (1~62)31 7 (1~65)33 15 (1~61)31 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 11 11 12 11 11 13 8 9 12 10 | 9 12 9 12 9 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot 1.1.3 (Mar 28 2018 - 12:57:21) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffb4000 Config XHCI 40M PLL flash manufacture id: ef, device id 40 19 find flash: W25Q256FV ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Mar 28 2018 Time:12:57:21 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN WLLLL Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 4 3 2 1 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... Image Name: MIPS OpenWrt Linux-5.10.72 Image Type: MIPS Linux Kernel Image (uncompressed) Data Size: 2845847 Bytes = 2.7 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.10.72 (homebuilt) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r17773-c4e994011f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Oct 18 22:14:36 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is ELECOM WRC-1167GST2 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30096 r8192 d23152 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00072800 [ 0.000000] Readback ErrCtl register=00072800 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 248780K/262144K available (7003K kernel code, 631K rwdata, 1408K rodata, 1248K init, 247K bss, 13364K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x3e4/0x618 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015853] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033723] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106053] pid_max: default: 32768 minimum: 301 [ 0.115322] LSM: Security Framework initializing [ 0.124413] SELinux: Initializing. [ 0.131408] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.145814] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.163964] rcu: Hierarchical SRCU implementation. [ 0.173747] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.189242] smp: Bringing up secondary CPUs ... [ 0.198850] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.198864] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.198881] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.198983] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.259170] Synchronize counters for CPU 1: done. [ 0.321236] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.321245] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.321252] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.321300] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.380199] Synchronize counters for CPU 2: done. [ 0.440433] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.440441] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.440449] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.440501] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.499770] Synchronize counters for CPU 3: done. [ 0.559378] smp: Brought up 1 node, 4 CPUs [ 0.571871] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.591376] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.605192] pinctrl core: initialized pinctrl subsystem [ 0.617529] NET: Registered protocol family 16 [ 0.626723] audit: initializing netlink subsys (disabled) [ 0.637698] audit: type=2000 audit(0.500:1): state=initialized audit_enabled=0 res=1 [ 0.653173] cpuidle: using governor teo [ 0.685635] random: fast init done [ 0.709485] clocksource: Switched to clocksource GIC [ 0.721371] NET: Registered protocol family 2 [ 0.730310] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.745360] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.761933] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.777078] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.791254] TCP: Hash tables configured (established 2048 bind 2048) [ 0.803998] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.816887] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.830958] NET: Registered protocol family 1 [ 0.839537] PCI: CLS 0 bytes, default 32 [ 0.850373] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.867643] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.879179] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.901399] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.912750] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.924259] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.936323] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.950700] printk: console [ttyS0] disabled [ 0.959158] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.977111] printk: console [ttyS0] enabled [ 0.977111] printk: console [ttyS0] enabled [ 0.993647] printk: bootconsole [early0] disabled [ 0.993647] printk: bootconsole [early0] disabled [ 1.015257] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 1.027693] spi-nor spi0.0: w25q256 (32768 Kbytes) [ 1.037384] 8 fixed-partitions partitions found on MTD device spi0.0 [ 1.050060] Creating 8 MTD partitions on "spi0.0": [ 1.059613] 0x000000000000-0x000000030000 : "u-boot" [ 1.070540] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.082379] 0x000000040000-0x000000050000 : "factory" [ 1.093653] 0x000000050000-0x000001850000 : "firmware" [ 1.105128] 2 uimage-fw partitions found on MTD device firmware [ 1.116949] Creating 2 MTD partitions on "firmware": [ 1.126844] 0x000000000000-0x0000002b6cd7 : "kernel" [ 1.136735] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 1.154120] 0x0000002b6cd7-0x000001800000 : "rootfs" [ 1.164040] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.183199] mtd: device 5 (rootfs) set to be root filesystem [ 1.194625] 1 squashfs-split partitions found on MTD device rootfs [ 1.206947] 0x000000a10000-0x000001800000 : "rootfs_data" [ 1.218633] 0x000001850000-0x000001c50000 : "tm_pattern" [ 1.230343] 0x000001c50000-0x000001d50000 : "tm_key" [ 1.241276] 0x000001d50000-0x000001e00000 : "nvram" [ 1.252163] 0x000001e00000-0x000002000000 : "user_data" [ 1.272323] libphy: Fixed MDIO Bus: probed [ 1.320920] libphy: mdio: probed [ 1.328290] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.343806] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20 [ 1.363770] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 1.377191] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 1.393504] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.409891] mt7621-pci 1e140000.pcie: Parsing DT failed [ 1.422718] NET: Registered protocol family 10 [ 1.433075] Segment Routing with IPv6 [ 1.440512] NET: Registered protocol family 17 [ 1.449785] 8021q: 802.1Q VLAN Support v1.8 [ 1.461783] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.489177] libphy: dsa slave smi: probed [ 1.497752] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) [ 1.517729] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) [ 1.537869] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) [ 1.558054] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) [ 1.578170] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) [ 1.598561] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 1.616428] DSA: tree 0 setup [ 1.622765] rt2880-pinmux pinctrl: pcie is already enabled [ 1.633804] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 1.647195] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 1.663521] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.679909] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 1.695076] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.810431] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.821563] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.932868] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) [ 1.946735] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.960616] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.970335] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.989054] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 2.001747] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 2.015444] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 2.029152] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.040089] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 2.060406] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 2.072386] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.084882] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 2.098919] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000] [ 2.110434] pci 0000:00:00.0: supports D1 [ 2.118403] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 2.131720] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.147971] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 2.159998] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 2.174044] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 2.186701] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 2.218159] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.228597] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 2.240751] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.254270] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref] [ 2.268662] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.281899] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 2.295069] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.308939] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.322467] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 2.336854] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 2.350389] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 2.363919] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.378483] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.388375] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 2.401903] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.415427] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 2.438928] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 2.457127] Freeing unused kernel memory: 1248K [ 2.466237] This architecture does not have kernel memory protection. [ 2.479090] Run /sbin/init as init process [ 2.487762] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 3.353034] audit: type=1404 audit(3.199:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 enabled=1 old-enabled=1 lsm=selinux res=1 [ 3.667335] SELinux: policy capability network_peer_controls=1 [ 3.679210] SELinux: policy capability open_perms=1 [ 3.689095] SELinux: policy capability extended_socket_class=1 [ 3.700878] SELinux: policy capability always_check_network=1 [ 3.712485] SELinux: policy capability cgroup_seclabel=1 [ 3.723224] SELinux: policy capability nnp_nosuid_transition=1 [ 3.735002] SELinux: policy capability genfs_seclabel_symlinks=1 [ 3.849599] audit: type=1403 audit(3.699:3): auid=4294967295 ses=4294967295 lsm=selinux res=1 [ 3.901037] init: Console is alive [ 3.908676] init: - watchdog - [ 4.815810] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.855173] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.889933] init: - preinit - [ 5.923588] random: jshn: uninitialized urandom read (4 bytes read) [ 6.013257] random: jshn: uninitialized urandom read (4 bytes read) [ 6.065180] random: jshn: uninitialized urandom read (4 bytes read) [ 6.371221] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 6.387322] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.390007] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 6.417705] 8021q: adding VLAN 0 to HW filter on device lan1 [ 6.431934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.446052] random: crng init done [ 6.452854] random: 6 urandom warning(s) missed due to ratelimiting Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.630459] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 10.645473] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 10.891548] jffs2: notice: (537) jffs2_build_xattr_subsystem: complete building xattr subsystem, 15 of xdatum (0 unchecked, 2 orphan) and 62 of xref (1 dead, 18 orphan) found. [ 10.925819] mount_root: switching to jffs2 overlay [ 10.944197] overlayfs: upper fs does not support tmpfile. [ 10.967149] urandom-seed: Seeding with /etc/urandom.seed [ 11.160453] mt7530 mdio-bus:1f lan1: Link is Down [ 11.181371] procd: - early - [ 11.187366] procd: - watchdog - [ 11.829703] procd: - watchdog - [ 11.852406] procd: - ubus - [ 12.022864] audit: type=1400 audit(11.869:4): avc: denied { watch } for pid=1 comm="procd" path="/etc/hotplug.d" dev="overlay" ino=19 scontext=u:r:sys.subj tcontext=u:r:unlabeled tclass=dir permissive=0 [ 12.063341] procd: - init - Please press Enter to activate this console. [ 12.855566] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.015264] urngd: v1.0.2 started. [ 13.079553] NET: Registered protocol family 38 [ 13.157939] cryptodev: driver 1.12 loaded. [ 13.168187] GACT probability on [ 13.176131] Mirror/redirect action on [ 13.196382] u32 classifier [ 13.201833] input device check on [ 13.209104] Actions configured [ 13.232555] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35 [ 13.247688] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32 [ 13.312604] xt_time: kernel timezone is -0000 [ 13.545748] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 13.556559] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 13.567852] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 13.597435] ieee80211 phy0: hwmon: 'mt7615-phy0' is not a valid name attribute, please fix [ 13.637475] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 13.637475] [ 13.650270] PPP generic driver version 2.4.2 [ 13.667431] NET: Registered protocol family 24 [ 13.682247] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 13.697889] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 13.747927] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.989292] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 14.112279] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 18.771646] audit: type=1400 audit(1634595338.449:5): avc: denied { write } for pid=1418 comm="fw3" name="net" dev="proc" ino=3404 scontext=u:r:sys.subj tcontext=u:r:sys.subj tclass=dir permissive=0 [ 23.087278] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 23.117097] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 23.133270] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 23.138158] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 23.164025] 8021q: adding VLAN 0 to HW filter on device lan1 [ 23.179625] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.193570] br-lan: port 1(lan1) entered blocking state [ 23.204105] br-lan: port 1(lan1) entered disabled state [ 23.216190] device lan1 entered promiscuous mode [ 23.225596] device eth0 entered promiscuous mode [ 23.271174] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 23.285197] 8021q: adding VLAN 0 to HW filter on device lan2 [ 23.301283] br-lan: port 2(lan2) entered blocking state [ 23.311809] br-lan: port 2(lan2) entered disabled state [ 23.324493] device lan2 entered promiscuous mode [ 23.350578] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 23.364533] 8021q: adding VLAN 0 to HW filter on device lan3 [ 23.380485] br-lan: port 3(lan3) entered blocking state [ 23.391003] br-lan: port 3(lan3) entered disabled state [ 23.404018] device lan3 entered promiscuous mode [ 23.429385] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 23.443265] 8021q: adding VLAN 0 to HW filter on device lan4 [ 23.459039] br-lan: port 4(lan4) entered blocking state [ 23.469640] br-lan: port 4(lan4) entered disabled state [ 23.482358] device lan4 entered promiscuous mode [ 23.520293] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 23.534012] 8021q: adding VLAN 0 to HW filter on device wan [ 24.056530] audit: type=1400 audit(1634595343.729:6): avc: denied { write } for pid=2008 comm="fw3" name="net" dev="proc" ino=1557 scontext=u:r:sys.subj tcontext=u:r:sys.subj tclass=dir permissive=0 [ 28.390381] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 28.405374] br-lan: port 1(lan1) entered blocking state [ 28.415807] br-lan: port 1(lan1) entered forwarding state [ 28.427441] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready Please press Enter to activate this console.


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/10/21 05:48
  • by laolux