User Tools

Site Tools


toh:easyacc:wizard8800

EasyAcc Wi-Stor Wizard 4in1 wireless storage 8800

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device will end after 2019.
19.07 will be the last official build for 4/32 devices. After 19.07, no further OpenWrt images will be built for 4/32 devices. See OpenWrt on 4/32 devices what you can do now.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
Wi-Stor Wizard 8800Ralink RT5350360432Ralink RT5350b/g/n-1--1x 2.0, 1x µUSB (charging), 1x Power only

Installation

Flash Layout

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00030000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "factory"
mtd3: 003b0000 00010000 "firmware"
mtd4: 002c0303 00010000 "rootfs"
mtd5: 00070000 00010000 "rootfs_data"

Hardware

Overview

CPU MIPS 24KEc V5.0
Architecture MIPS
System-On-Chip 360 MHZ Ralink RT5350 id:1 rev:3
Flash 4 MB Winbond W25Q32BV
RAM 32 MB Etron EM63A165TS-6G
Ethernet Yes 1x (10/100Mbit )
USB Yes 2x (USB Battery Charging, EHCI/OHCI)
Power Supply 8800mAh Li-ion battery (4 Cell 3,6V ICR-18650NH )

CPU Info

root@OpenWrt:~# cat /proc/cpuinfo
system type             : Ralink RT5350 id:1 rev:3
machine                 : EASYACC WI-STOR WIZARD 8800
processor               : 0
cpu model               : MIPS 24KEc V4.12
BogoMIPS                : 239.61
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0000, 0x00a0, 0x0720, 0x0728]
isa                     : mips1 mips2 mips32r1 mips32r2
ASEs implemented        : mips16 dsp
shadow register sets    : 1
kscratch registers      : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

MEM Info

root@OpenWrt:/# cat /proc/meminfo
MemTotal:          29556 kB
MemFree:           13068 kB
Buffers:            1844 kB
Cached:             5340 kB
SwapCached:            0 kB
Active:             3924 kB
Inactive:           4456 kB
Active(anon):       1216 kB
Inactive(anon):       20 kB
Active(file):       2708 kB
Inactive(file):     4436 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:          1212 kB
Mapped:             1236 kB
Shmem:                40 kB
Slab:               4356 kB
SReclaimable:        952 kB
SUnreclaim:         3404 kB
KernelStack:         288 kB
PageTables:          180 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       14776 kB
Committed_AS:       3368 kB
VmallocTotal:    1048372 kB
VmallocUsed:         552 kB
VmallocChunk:    1044204 kB

Images

Serial

Pinout

1 2 3 4
TX RX GND VCC

Serial connection parameters: 57600, 8N1

Linux Connect

sudo screen /dev/ttyUSB3 57600

Bootlog

U-Boot 1.1.3 (Sep 13 2012 - 16:39:43) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 42 spi device id: ef 40 16 0 0 (40160000) find flash: W25Q32BV raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Sep 13 2012 Time:16:39:43 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: Linux Kernel Image Created: 2014-04-16 18:22:25 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 982205 Bytes = 959.2 kB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:efcbd ............... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 3.10.36 (openwrt@openwrt) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40477) ) #9 Wed Apr 16 20:11:30 CEST 2014 [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is EASYACC WI-STOR WIZARD 8800 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00073523 [ 0.000000] Readback ErrCtl register=00073523 [ 0.000000] Memory: 29356k/32768k available (2134k kernel code, 3412k reserved, 543k data, 200k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 360MHz [ 0.000000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] pinctrl core: initialized pinctrl subsystem [ 0.090000] NET: Registered protocol family 16 [ 0.110000] rt2880-pinmux pinctrl.1: invalid group "rgmii" for function "gpio" [ 0.120000] rt2880-pinmux pinctrl.1: invalid group "mdio" for function "gpio" [ 0.150000] bio: create slab <bio-0> at 0 [ 0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.170000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.180000] Switching to clocksource MIPS [ 0.190000] NET: Registered protocol family 2 [ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.230000] TCP: Hash tables configured (established 512 bind 512) [ 0.240000] TCP: reno registered [ 0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.270000] NET: Registered protocol family 1 [ 0.280000] rt-timer 10000100.timer: maximum frequncy is 7324Hz [ 0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.370000] msgmni has been set to 57 [ 0.380000] io scheduler noop registered [ 0.380000] io scheduler deadline registered (default) [ 0.400000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.410000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.430000] console [ttyS0] enabled, bootconsole disabled [ 0.430000] console [ttyS0] enabled, bootconsole disabled [ 0.460000] m25p80 spi32766.0: w25q32 (4096 Kbytes) [ 0.470000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.480000] Creating 4 MTD partitions on "spi32766.0": [ 0.490000] 0x000000000000-0x000000030000 : "u-boot" [ 0.510000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.520000] 0x000000040000-0x000000050000 : "factory" [ 0.530000] 0x000000050000-0x000000800000 : "firmware" [ 0.540000] mtd: partition "firmware" extends beyond the end of device "spi32766.0" -- size truncated to 0x3b0000 [ 0.570000] 0x00000013fcfd-0x000000400000 : "rootfs" [ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.610000] mtd: device 4 (rootfs) set to be root filesystem [ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x390000, len=0x70000 [ 0.640000] 0x000000390000-0x000000400000 : "rootfs_data" [ 0.660000] eth0: done loading [ 0.670000] rt3xxx-usbphy ubsphy.3: loaded [ 0.680000] rt2880_wdt 10000120.watchdog: Initialized [ 0.690000] TCP: cubic registered [ 0.700000] NET: Registered protocol family 17 [ 0.710000] 8021q: 802.1Q VLAN Support v1.8 [ 0.730000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.750000] Freeing unused kernel memory: 200K (8029e000 - 802d0000) procd: Console is alive procd: - watchdog - procd: - preinit - [ 6.860000] rt305x-esw 10110000.esw: link changed 0x00 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.710000] usbcore: registered new interface driver usbfs [ 8.720000] usbcore: registered new interface driver hub [ 8.730000] usbcore: registered new device driver usb [ 8.770000] SCSI subsystem initialized [ 8.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.800000] ehci-platform: EHCI generic platform driver [ 9.010000] rt3xxx-usbphy ubsphy.3: remote usb device wakeup disabled [ 9.020000] rt3xxx-usbphy ubsphy.3: UTMI 16bit 30MHz [ 9.030000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 9.050000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 9.060000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 9.100000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 9.110000] hub 1-0:1.0: USB hub found [ 9.120000] hub 1-0:1.0: 1 port detected [ 9.140000] dwc_otg: version 2.72a 24-JUN-2008 [ 9.160000] usbcore: registered new interface driver usb-storage [ 9.450000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 9.610000] hub 1-1:1.0: USB hub found [ 9.620000] hub 1-1:1.0: 4 ports detected [ 9.910000] usb 1-1.2: new high-speed USB device number 3 using ehci-platform [ 10.030000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 10.050000] scsi0 : usb-storage 1-1.2:1.0 [ 10.140000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform kmod: ran 1 iterations [ 11.060000] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0207 PQ: 0 ANSI: 0 [ 11.240000] sd 0:0:0:0: [sda] 15523840 512-byte logical blocks: (7.94 GB/7.40 GiB) [ 11.270000] sd 0:0:0:0: [sda] Write Protect is off [ 11.290000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.300000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.360000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.380000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.420000] sda: sda1 [ 11.470000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.480000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.490000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 11.750000] jffs2: notice: (294) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found. block: extroot: no root or overlay mount defined jffs2 is ready [ 12.050000] jffs2: notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found. switching to jffs2 procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 14.970000] NET: Registered protocol family 10 [ 15.000000] nf_conntrack version 0.5.0 (461 buckets, 1844 max) [ 15.020000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 15.070000] fuse init (API version 7.22) [ 15.090000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2 [ 15.110000] Backport generated by backports.git backports-20140221-0-g8e94650 [ 15.130000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.190000] usbcore: registered new interface driver ums-alauda [ 15.200000] usbcore: registered new interface driver ums-cypress [ 15.220000] usbcore: registered new interface driver ums-datafab [ 15.240000] usbcore: registered new interface driver ums-freecom [ 15.250000] usbcore: registered new interface driver ums-isd200 [ 15.270000] usbcore: registered new interface driver ums-jumpshot [ 15.290000] usbcore: registered new interface driver ums-karma [ 15.300000] usbcore: registered new interface driver ums-sddr09 [ 15.320000] usbcore: registered new interface driver ums-sddr55 [ 15.340000] usbcore: registered new interface driver ums-usbat [ 15.390000] xt_time: kernel timezone is -0000 [ 15.450000] cfg80211: Calling CRDA to update world regulatory domain [ 15.460000] cfg80211: World regulatory domain updated: [ 15.470000] cfg80211: DFS Master region: unset [ 15.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 15.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.520000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.530000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 15.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 15.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 15.580000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 15.680000] PPP generic driver version 2.4.2 [ 15.700000] NET: Registered protocol family 24 [ 15.760000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 15.770000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. [ 15.790000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected [ 15.810000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected procd: - init complete - [ 26.210000] device eth0 entered promiscuous mode [ 26.230000] br-lan: port 1(eth0) entered forwarding state [ 26.240000] br-lan: port 1(eth0) entered forwarding state [ 28.240000] br-lan: port 1(eth0) entered forwarding state BusyBox v1.19.4 (2014-04-15 21:10:54 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r40477) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/easyacc/wizard8800.txt · Last modified: 2019/02/12 21:23 by tmomas