D-Link DIR-878 A1

The D-Link DIR-878 is a Wi-Fi 5 Wave 2 router based on MediaTek MT7621A with 16 MB flash and 128 MB RAM. It has 5 Gigabit Ethernet ports and dual MediaTek MT7615N radios, capable of up to 4×4 streams on each band.

DIR-878

None at this time.

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
DIR-878A1MediaTek MT7621AT88016128MediaTek MT7615Nb/g/na/n/ac-5--

Please read this article for a better understanding, as it contains a couple of explanations. The sections below describes the flash layout of this router when running the stock firmware and when running OpenWrt.

Stock Firmware

Layer0 raw flash, 16384 KiB
Layer1 mtd0
ALL
16384 KiB
Layer2 mtd1
Bootloader
192 KiB
mtd2
Config
64 KiB
mtd3
Factory
64 KiB
mtd4
Config2
64 KiB
mtd5
Kernel
15680 KiB
mtd6
Private
320 KiB
  • Config partition stores the environment variables from U-Boot.
  • Factory partition stores the MAC addresses and calibration data of the MT7615N wireless modules.
  • Config2 partition stores the default country code, default WiFi password and unique D-Link FOTA identifiers.
  • Private partition stores the router settings. A factory reset erases all content from this partition.

Warning: Factory and Config2 partitions contains unique data, specific to each unit. If they get erased or corrupted, stock firmware will lose the ability to automatically apply firmware updates, will get stuck on a bootloop if a factory reset is performed and Wi-Fi won't work anymore. D-Link Recovery GUI cannot fix this.

OpenWrt

Layer0 raw flash, 16384 KiB
Layer1 mtd0
u-boot
192 KiB
mtd1
u-boot-env
64 KiB
mtd2
factory
128 KiB
mtd3
firmware
16000 KiB
Layer2 mtd4
kernel
2391.4 KiB
mtd5
rootfs
13608.6 KiB
Layer3
/rom
2664.6 KiB
mtd6
rootfs_data
10944 KiB

Different from stock firmware, OpenWrt doesn't make distinction between the Factory and Config2 partitions, instead it maps both of them to a single read-only partition, factory, at the same address range. Regardless, it still holds the same unique data specific to each unit, and all sorts of issues can happen if this partition gets corrupted or erased.

generic.flashing.tftp

Although this router supports flashing the firmware and even the bootloader through TFTP, these flashing modes can only be selected by interacting with the U-Boot terminal at boot time, through the serial port. The section below lists the default values, although the router will always ask for the desired parameters when selecting any of the TFTP flash options on the U-Boot console.

Specific values needed for TFTP

Bootloader TFTP server IPv4 address 192.168.0.1
Firmware TFTP image Latest OpenWrt release (NOTE: use the factory images)
TFTP transfer window indefinite
TFTP window start N/A
TFTP client required IP address 192.168.0.101
  • Browse to http://192.168.1.1/cgi-bin/luci/admin/system/flash (LuCI Upgrade URL);
  • Upload image file for sysupgrade to LuCI;
  • Confirm whether existing settings should be kept;
  • Wait for reboot.

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-dlink_dir-8xx-a1-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ramips-mt7621-dlink_dir-8xx-a1-squashfs-sysupgrade.bin

Note: Replace the 8xx in the link and filename with the model number of your router, e.g. 867.

mtd

Alternatively, you can use mtd. Keep in mind that mtd won't save any existing settings.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-dlink_dir-8xx-a1-squashfs-factory.bin
mtd -r write /tmp/openwrt-ramips-mt7621-dlink_dir-8xx-a1-squashfs-factory.bin firmware

Note: Replace the 8xx in the link and filename with the model number of your router, e.g. 867.

generic.debrick

In case of a brick, a new firmware can still be uploaded through D-Link Recovery GUI. Keep in mind the recovery GUI only accepts unencrypted firmware images. A tool to decrypt factory images is available here. Alternatively, a new firmware can be flashed through the serial port or through TFTP, but you'll need to interact with the U-Boot console at power up to select any of these modes.

Be careful when playing around with the bootloader, as in case of a bootloader brick neither the emergency recovery mode nor the serial and TFTP flash options will be accessible. Since this router doesn't have a JTAG port, only reprogramming the flash chip through an external programmer can solve this kind of brick.

The stock firmware files provided by D-Link doesn't contain the bootloader, so obtaining a copy of it can be tricky. To help with that, an unmodified copy of the stock bootloader, dumped directly from the flash chip of a working unit, can be downloaded here.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN ports & both Wi-Fi radios 192.168.1.1/24
wan WAN port DHCP
wlan0 Wi-Fi 2.4 GHz Disabled
wlan1 Wi-Fi 5 GHz Disabled

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) 4
LAN 1 3
LAN 2 2
LAN 3 1
LAN 4 0

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

This router has the following buttons:

BUTTON Event
Reset reset
Wi-Fi rfkill
WPS wps
General
Brand D-Link
Model DIR-878
Versions A1
Device Type WiFi Router
Availability Available 2019
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d7233b0a6a9b8cb9207a74a8cb3d0525170cf504
Supported Since Release
Supported Current Release snapshot
Unsupported
Hardware
Bootloader U-Boot
Target ramips
System-On-Chip MediaTek MT7621AT
CPU MHz 880
Flash MB 16
RAM MB 128
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch -
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware MediaTek MT7615N
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 6
Button count 3
Power supply 12 VDC, 1.5 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/D-Link_DIR-878_rev_A1
OEM device homepage URL https://www.dlink.com/en/products/dir-878-ac1900-mu-mimo-wi-fi-router
Firmware OEM Stock URL https://support.dlink.com/ProductInfo.aspx?m=DIR-878
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL
Edit the underlying data View/Edit data

Front:

Back:

Backside label:
FIXME Insert photo of backside label

Note: This will void your warranty!

Remove the 4 rubber feets and the 4 screws underneath them, then carefully unclip the plastic tabs around the top cover. All of the tabs are on the top cover.

Main PCB:
FIXME Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

  • Serial port is located on the J1 header, next to the Wi-Fi, Reset and WPS buttons.
  • It comes from factory without a pin header, you must solder one before you can use it.
  • The board uses 3V3 logic level, double check the specifications of the USB-TTL dongle you have before connecting.
  • Don’t forget that the TX pin of the router should be connected to the RX pin of the serial port and the RX to TX.
Serial connection parameters 57600, 8N1

Serial header location and pinout

bootloader

None so far.

None so far.

=================================================================== MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xa, 1/0 = 717/307 29000000 PLL4 FB_DL: 0xe, 1/0 = 560/464 39000000 PLL2 FB_DL: 0x18, 1/0 = 635/389 61000000 do DDR setting..[01F40000] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 80 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00002121 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 7 9 11 7 7 9 6 6 7 10 | 9 9 9 11 9 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =33 DQS1 = 33 ================================================================== bit DQS0 bit DQS1 0 (1~63)32 8 (1~62)31 1 (1~63)32 9 (1~62)31 2 (1~64)32 10 (1~66)33 3 (1~66)33 11 (1~64)32 4 (1~65)33 12 (1~66)33 5 (1~65)33 13 (1~62)31 6 (1~65)33 14 (1~65)33 7 (1~66)33 15 (1~63)32 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 8 10 11 7 7 9 6 8 9 10 | 9 10 9 13 9 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0080 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot 1.1.3 (Jul 19 2017 - 20:51:21) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb4000 Config XHCI 40M PLL flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jul 19 2017 Time:20:51:21 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 6: System Enter UBoot to Update Img or Bin. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3  0 3: System Boot system code via Flash. ## Booting image at bc060000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 11181071 Bytes = 10.7 MB Load Address: 81001000 Entry Point: 815ff440 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 815ff440) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 3.10.14+ (zengqinghuang@wireless) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #34 SMP Thu May 16 15:14:21 CST 2019 The CPU feqenuce set to 880 MHz GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone ranges: DMA [mem 0x00000000-0x00ffffff] Normal [mem 0x01000000-0x07ffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x07ffffff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 7 pages/cpu @821aa000 s6592 r8192 d13888 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 rdinit=/sbin/preinit PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Writing ErrCtl register=00000024 Readback ErrCtl register=00000024 Memory: 112760k/131072k available (6177k kernel code, 18312k reserved, 2403k data, 7604k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_PCI_PCICFG_ADDR= 21007f2 RALINK_PCI_PCICFG_ADDR = 21007f0 RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f0 -> 21007f0 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 1, 8192 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) Load Kernel WDG Timer Module jffs2: version 2.2. (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. fuse init (API version 7.22) io scheduler noop registered (default) reg_int_mask=0, INT_MASK= 0 HSDMA_init hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 TX_CTX_IDX0 = 0 TX_DTX_IDX0 = 0 RX_CRX_IDX0 = 3ff RX_DRX_IDX0 = 0 set_fe_HSDMA_glo_cfg HSDMA_GLO_CFG = 465 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A Ralink gpio driver initialized:power_gpio[8] brd: module loaded flash manufacture id: ef, device id 40 18 W25Q128BV(ef 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "Config2" 0x000000060000-0x000000fb0000 : "Kernel" 0x000000fb0000-0x000001000000 : "Private" IMQ driver loaded successfully. (numdevs = 2, numqueues = 1) Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register mt_drv === pAd = c2201000, size = 3761560 === <-- RTMPAllocAdapterBlock, Status=0 get_wdev_by_idx: invalid idx(0) pAd->PciHif.CSRBaseAddress =0xc2100000, csr_addr=0xc2100000! get_wdev_by_idx: invalid idx(0) RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 1st iPAiLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_2G_EEPROM.bin Use 1st iPAiLNA default bin. Use 0st /etc_ro/wlan/MT7615E_EEPROM1.bin default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 87ff3888,87ff3888 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 87ff3898,87ff3898 <-- RTMPAllocTxRxRingMemory, Status=0 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) === pAd = c2701000, size = 3761560 === <-- RTMPAllocAdapterBlock, Status=0 get_wdev_by_idx: invalid idx(0) pAd->PciHif.CSRBaseAddress =0xc2600000, csr_addr=0xc2600000! get_wdev_by_idx: invalid idx(0) RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 2nd iPAiLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_5G_EEPROM.bin Use 2nd iPAiLNA default bin. Use 1st /etc_ro/wlan/MT7615E_EEPROM2.bin default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 85f6b908,85f6b908 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 85f6b918,85f6b918 <-- RTMPAllocTxRxRingMemory, Status=0 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000xxxx GMAC1_MAC_ADRL -- : 0xxxxxxx55 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000xxxx GMAC1_MAC_ADRL -- : 0xxxxxxx55 PROC INIT OK! ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver *****run project phy. FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected u32 classifier Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1761 buckets, 7044 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team Type=Linux arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 Warning: unable to open an initial console. Freeing unused kernel memory: 7604K (81863000 - 81fd0000) [system]: tw_hotplug & Algorithmics/MIPS FPU Emulator v1.5 [system]: insmod /lib/modules/3.10.14+/kernel/drivers/usb/storage/usb-storage.ko usbcore: registered new interface driver usb-storage crc fail 1ee16f25 != fe2122b9 old 0.4, now 0.4 [system]: killall nvram_daemon [system]: nvram_daemon & [check_Default_Config]factory_flag=2[system]: gpio l 8 4000 0 1 0 4000 [system]: chpasswd -m < /tmp/tmpchpw Password for 'admin' changed [system]: chmod 644 /etc/passwd [system]: addgroup -g 500 nobody [system]: adduser -H -D -G nobody nobody [system]: addgroup -g 600 root [system]: adduser -H -D -G root root [system]: ifconfig eth2 0.0.0.0 xx:xx:xx:xx:xx:55 Raeth v3.1 (Tasklet) set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0xca8000!!! phy_free_tail_phy is 0xca9ff0!!! txd_pool=a0cb0000 phy_txd_pool=00CB0000 ei_local->skb_free start address is 0x8610a6dc. free_txd: 00cb0010, ei_local->cpu_ptr: 00CB0000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0cb0000 0x00CB0000 0x00CB0000 phy_qrx_ring = 0x00caa000, qrx_ring = 0xa0caa000 phy_rx_ring0 = 0x00cac000, rx_ring0 = 0xa0cac000 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000xxxx GMAC1_MAC_ADRL -- : 0xxxxxxx55 GDMA2_MAC_ADRH -- : 0x0000xxxx GDMA2_MAC_ADRL -- : 0xxxxxxx58 eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 [system]: ifconfig eth3 up eth3: ===> VirtualIF_open [system]: config-vlan.sh 3 0 restore GSW to dump switch mode switch reg write offset=2004, value=ff0000 switch reg write offset=2104, value=ff0000 switch reg write offset=2204, value=ff0000 switch reg write offset=2304, value=ff0000 switch reg write offset=2404, value=ff0000 switch reg write offset=2504, value=ff0000 switch reg write offset=2604, value=ff0000 switch reg write offset=2704, value=ff0000 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=810000c0 switch reg write offset=2710, value=810000c0 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [system]: switch vlan set 1 1 11110011 [system]: switch vlan set 2 2 00001100 [system]: switch pvid 4 2 Set port 4 pvid 2. [system]: switch pvid 5 2 Set port 5 pvid 2. [system]: switch reg w 2004 ff0003 switch reg write offset=2004, value=ff0003 [system]: switch reg w 2104 ff0003 switch reg write offset=2104, value=ff0003 [system]: switch reg w 2204 ff0003 switch reg write offset=2204, value=ff0003 [system]: switch reg w 2304 ff0003 switch reg write offset=2304, value=ff0003 [system]: switch reg w 2404 ff0003 switch reg write offset=2404, value=ff0003 [system]: switch reg w 2504 ff0003 switch reg write offset=2504, value=ff0003 [system]: switch reg w 2604 ff0003 switch reg write offset=2604, value=ff0003 [system]: ifconfig lo 127.0.0.1 [system]: vconfig add eth2 1 [system]: vconfig set_ingress_map eth2.1 0 0 [system]: vconfig set_ingress_map eth2.1 1 1 [system]: vconfig set_ingress_map eth2.1 2 2 [system]: vconfig set_ingress_map eth2.1 3 3 [system]: vconfig set_ingress_map eth2.1 4 4 [system]: vconfig set_ingress_map eth2.1 5 5 [system]: vconfig set_ingress_map eth2.1 6 6 [system]: vconfig set_ingress_map eth2.1 7 7 [system]: vconfig set_egress_map eth2.1 0 0 [system]: vconfig set_egress_map eth2.1 1 1 [system]: vconfig set_egress_map eth2.1 2 2 [system]: vconfig set_egress_map eth2.1 3 3 [system]: vconfig set_egress_map eth2.1 4 4 [system]: vconfig set_egress_map eth2.1 5 5 [system]: vconfig set_egress_map eth2.1 6 6 [system]: vconfig set_egress_map eth2.1 7 7 [system]: vconfig add eth2 2 [system]: vconfig set_ingress_map eth2.2 0 0 [system]: vconfig set_ingress_map eth2.2 1 1 [system]: vconfig set_ingress_map eth2.2 2 2 [system]: vconfig set_ingress_map eth2.2 3 3 [system]: vconfig set_ingress_map eth2.2 4 4 [system]: vconfig set_ingress_map eth2.2 5 5 [system]: vconfig set_ingress_map eth2.2 6 6 [system]: vconfig set_ingress_map eth2.2 7 7 [system]: vconfig set_egress_map eth2.2 0 0 [system]: vconfig set_egress_map eth2.2 1 1 [system]: vconfig set_egress_map eth2.2 2 2 [system]: vconfig set_egress_map eth2.2 3 3 [system]: vconfig set_egress_map eth2.2 4 4 [system]: vconfig set_egress_map eth2.2 5 5 [system]: vconfig set_egress_map eth2.2 6 6 [system]: vconfig set_egress_map eth2.2 7 7 [system]: vconfig add eth2 3 [system]: vconfig set_ingress_map eth2.3 0 0 [system]: vconfig set_ingress_map eth2.3 1 1 [system]: vconfig set_ingress_map eth2.3 2 2 [system]: vconfig set_ingress_map eth2.3 3 3 [system]: vconfig set_ingress_map eth2.3 4 4 [system]: vconfig set_ingress_map eth2.3 5 5 [system]: vconfig set_ingress_map eth2.3 6 6 [system]: vconfig set_ingress_map eth2.3 7 7 [system]: vconfig set_egress_map eth2.3 0 0 [system]: vconfig set_egress_map eth2.3 1 1 [system]: vconfig set_egress_map eth2.3 2 2 [system]: vconfig set_egress_map eth2.3 3 3 [system]: vconfig set_egress_map eth2.3 4 4 [system]: vconfig set_egress_map eth2.3 5 5 [system]: vconfig set_egress_map eth2.3 6 6 [system]: vconfig set_egress_map eth2.3 7 7 [system]: vconfig add eth2 4 [system]: vconfig set_ingress_map eth2.4 0 0 [system]: vconfig set_ingress_map eth2.4 1 1 [system]: vconfig set_ingress_map eth2.4 2 2 [system]: vconfig set_ingress_map eth2.4 3 3 [system]: vconfig set_ingress_map eth2.4 4 4 [system]: vconfig set_ingress_map eth2.4 5 5 [system]: vconfig set_ingress_map eth2.4 6 6 [system]: vconfig set_ingress_map eth2.4 7 7 [system]: vconfig set_egress_map eth2.4 0 0 [system]: vconfig set_egress_map eth2.4 1 1 [system]: vconfig set_egress_map eth2.4 2 2 [system]: vconfig set_egress_map eth2.4 3 3 [system]: vconfig set_egress_map eth2.4 4 4 [system]: vconfig set_egress_map eth2.4 5 5 [system]: vconfig set_egress_map eth2.4 6 6 [system]: vconfig set_egress_map eth2.4 7 7 [system]: ifconfig eth2 up [system]: ifconfig eth2.1 0.0.0.0 up [system]: ifconfig eth2.2 0.0.0.0 up [system]: ifconfig eth2.3 0.0.0.0 up [system]: ifconfig eth2.4 0.0.0.0 up [system]: ifconfig eth3 0.0.0.0 up [system]: config-vlan.sh 3 0 restore GSW to dump switch mode switch reg write offset=2004, value=ff0000 switch reg write offset=2104, value=ff0000 switch reg write offset=2204, value=ff0000 switch reg write offset=2304, value=ff0000 switch reg write offset=2404, value=ff0000 switch reg write offset=2504, value=ff0000 switch reg write offset=2604, value=ff0000 switch reg write offset=2704, value=ff0000 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=810000c0 switch reg write offset=2710, value=810000c0 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [system]: switch vlan set 1 1 10000011 [system]: switch vlan set 2 2 01000011 [system]: switch vlan set 3 3 00100011 [system]: switch vlan set 4 4 00010011 [system]: switch vlan set 5 5 00001100 [system]: switch reg w 2010 810000c0 switch reg write offset=2010, value=810000c0 [system]: switch reg w 2110 810000c0 switch reg write offset=2110, value=810000c0 [system]: switch reg w 2210 810000c0 switch reg write offset=2210, value=810000c0 [system]: switch reg w 2310 810000c0 switch reg write offset=2310, value=810000c0 [system]: switch reg w 2410 810000c0 switch reg write offset=2410, value=810000c0 [system]: switch reg w 2510 810000c0 switch reg write offset=2510, value=810000c0 [system]: switch reg w 2610 81000000 switch reg write offset=2610, value=81000000 [system]: switch pvid 0 1 Set port 0 pvid 1. [system]: switch pvid 1 2 Set port 1 pvid 2. [system]: switch pvid 2 3 Set port 2 pvid 3. [system]: switch pvid 3 4 Set port 3 pvid 4. [system]: switch pvid 4 5 Set port 4 pvid 5. [system]: switch pvid 5 5 Set port 5 pvid 5. [system]: switchRalink HW NAT Module Enabled reg w 2004 ff00eth2 ifindex =6 03 switch reg eth3 ifindex =9 write offset=2004, value=ff0003 [system]: switch reg w 2104 ff0003 switch reg write offset=2104, value=ff0003 [system]: switch reg w 2204 ff0003 switch reg write offset=2204, value=ff0003 [system]: switch reg w 2304 ff0003 switch reg write offset=2304, value=ff0003 [system]: switch reg w 2404 ff0003 switch reg write offset=2404, value=ff0003 [system]: switch reg w 2504 ff0003 switch reg write offset=2504, value=ff0003 [system]: switch reg w 2604 20ff0003 switch reg write offset=2604, value=20ff0003 [system]: switch reg w 2014 10001 switch reg write offset=2014, value=10001 [system]: switch reg w 2114 10002 switch reg write offset=2114, value=10002 [system]: switch reg w 2214 10003 switch reg write offset=2214, value=10003 [system]: switch reg w 2314 10004 switch reg write offset=2314, value=10004 [system]: switch vlan set 0 5 00001100 [system]: insmod -q ehci-hcd insmod: ehci-hcd.ko: module not found [system]: insmod -q ohci-hcd insmod: ohci-hcd.ko: module not found [system]: insmod -q xhci-hcd insmod: xhci-hcd.ko: module not found [system]: insmod -q xhci-hcd insmod: xhci-hcd.ko: module not found [system]: insmod -q hw_nat [system]: ralink_init make_wireless_config rt2860 [system]: ralink_init make_wireless_config rtdev [system]: cp -rf /etc_ro/Wireless/RT2860AP/SingleSKU_24G_RCM.dat /var/Wireless/7615_SingleSKU_24G.dat [system]: cp -rf /etc_ro/Wireless/RT2860AP/SingleSKU_5G_RCM.dat /var/Wireless/7615_SingleSKU_5G.dat [system]: cp -rf /etc_ro/Wireless/RT2860AP/SKU_24G_RCM_BF.dat /varrecv is :Hello you! /Wireless/7615_BF_SKU_24G.dat cp: cannot stat '/etc_ro/Wireless/RT2860AP/SKU_24G_RCM_BF.dat': No such file or directory [system]: cp -rf /etc_ro/Wireless/RT2860AP/SKU_5G_RCM_BF.dat /var/Wireless/7615_BF_SKU_5G.dat cp: cannot stat '/etc_ro/Wireless/RT2860AP/SKU_5G_RCM_BF.dat': No such file or directory e2p_lan mac = xx:xx:xx:xx:xx:55 lanmac=6418261 check_wlan_mac:wlan_2g_mac=6418262,wlan_5g_mac=6418263,lanmac=6418261 wan mac = xx:xx:xx:xx:xx:58 wanmac=6418264 mydlink UID = ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ sh: mydlinknumber: not found Set: port0 dev1Eh_reg16h = 0x0014 Set: port1 dev1Eh_reg16h = 0x0014 Set: port2 dev1Eh_reg16h = 0x0014 Set: port3 dev1Eh_reg16h = 0x0015 Set: port4 dev1Eh_reg16h = 0x0016 [system]: switch reg w 7d00 77777;switch reg w 7d04 77777 switch reg write offset=7d00, value=77777 switch reg write offset=7d04, value=77777 [system]: stad 1 & [system]: stad 2 & [system]: ln -sf /tmp/resolv.conf /etc/resolv.conf waiting received! [system]: ln -sf /tmp/hosts /etc/hosts certificate req and private key is ok writing RSA key [system]: echo -n bGl1c2hlbmdodWk= > /tmp/dhcp6sctlkey Hit ENTER for console... Hit enter to continue...ESW: Link Status Changed - Port3 Link UP cmd> [system]: fota_config init mtk/fota_generate_config.c, main, 1060: Execute config ACTION: init. mtk/fota_generate_config.c, fota_check_config, 121: Now check fota configuration. mtk/fota_generate_config.c, main, 1068: Done. set_action: 1: set_action 0 start_timer: start timer done [system]: dxtimer calls setitimer() with new_value NULL pointer. Misfeature support will be removed ml -n dbros -t & [system]: dxmlc -l /etc_ro/onetouch/device.xml [system]: insmod /lib/modules/dlink_nl_ctrl.ko dlink_nl_ctrl: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint D-Link Netlink module version 1.0. [system]: insmod /lib/modules/3.10.14+/kernel/drivers/net/wireless/MTK7615/mt_wifi_ap/mt_wifi.ko insmod: mt_wifi.ko: module not found [system]: starter & set_action: 1: set_action 10 start_lan_br: enterdevice eth2.4 entered promiscuous mode ESW: Link Status Changed - Port4 Link UP [system]: brctdevice eth2 entered promiscuous mode l addbr br0 [sESW: Send SIGUSR2 to timer[445] ystem]: brctl addif br0 eth2.4 notify_rc_interdevice eth2.3 entered promiscuous mode nal: <rc_service> [timer] 445:notify_rc restart_device eth2.2 entered promiscuous mode wanall [system]: brctl addif br0 eth2.3 [systdevice eth2.1 entered promiscuous mode em]: brctl addif br0 eth2.2 [system]: brctl addif br0 eth2.1 [system]: brctl addif br0 ra0 brctl: bridge br0: Invalid argument [system]: brctl addif br0 rai0 brctl: bridge br0: Invalid argument [system]: brctl addbr br1 [system]: brctl addif br1 ra1 brctl: iface ra1: No such device [system]: brctl addif br1 rai1 brctlbr0: port 4(eth2.1) entered forwarding state : iface rai1: Nobr0: port 4(eth2.1) entered forwarding state such device [sbr0: port 3(eth2.2) entered forwarding state ystem]: brctl adbr0: port 3(eth2.2) entered forwarding state dbr br2 [systebr0: port 2(eth2.3) entered forwarding state m]: brctl addbr br0: port 2(eth2.3) entered forwarding state br3 start_lan_br0: port 1(eth2.4) entered forwarding state br: done br0: port 1(eth2.4) entered forwarding state start_lan_ipv6: br0: port 4(eth2.1) entered disabled state enter br0: port 3(eth2.2) entered disabled state br0: port 2(eth2.3) entered disabled state br0: port 1(eth2.4) entered disabled state br0: port 4(eth2.1) entered forwarding state br0: port 4(eth2.1) entered forwarding state br0: port 3(eth2.2) entered forwarding state br0: port 3(eth2.2) entered forwarding state br0: port 2(eth2.3) entered forwarding state br0: port 2(eth2.3) entered forwarding state br0: port 1(eth2.4) entered forwarding state br0: port 1(eth2.4) entered forwarding state p= br2: Cannot assign requested address br3: Cannot assign requested address start_dev_mgt_link: enter [system]: hostname dlinkrouter [system]: nl_server -i br0 -s dlinkrouter -s dlinkrouterEF55 -s dlinkrouter.local -s dlinkrouterEF55.local & start_mdns_responder: enter nbns and llmnr server starting... major_ver:1,minor_ver:20 fota_major_ver:0,fota_minor_ver:0 [system]: mDNSResponder -b -i br0 -f /tmp/mdns_resp.conf -e dlinkrouter -e dlinkrouterEF55 [system]: mdnsd sh: mdnsd: not found start_mdns_responder: done start_dev_mgt_link: done [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event get_wdev_by_idx: invalid idx(0) --log-async [sget_wdev_by_idx: invalid idx(0) ystem]: echo 1 >get_wdev_by_idx: invalid idx(0) /proc/net/arp_spoofing_enable get_wdev_by_idx: invalid idx(0) [system]: switcget_wdev_by_idx: invalid idx(0) h reg w 2014 10get_wdev_by_idx: invalid idx(0) 001 switch reg write offset=2014, value=10001 [system]: switch reg w 2114 10002 switch reg write offset=2114, value=10002 [system]: switch reg w 2214 10003 switch reg write offset=2214, value=10003 [system]: switch reg w 2314 10004 switch reg write offset=2314, value=10004 [system]: switch vlan set 0 5 00001100 start_dhcp6s: done start_radvd: done Start lighttpd ... [system]: /bin/lighttpd -f /etc_ro/lighttpd/lighttpd.conf -m /etc_ro/lighttpd/lib/ 2019-05-16 14:57:16: (log.c.169) server started [system]: killall -9 timer May 16 14:57:17 [MDNS]: mDNSPlatformSendUDP got error 126 (Cannot assign requested address) sending packet to FF02:0000:0000:0000:0000:0000:0000:00FB on interface 192.168.0.1/br0/14 May 16 14:57:17 [MDNS]: mDNSPlatformSendUDP got error 126 (Cannot assign requested address) sending packet to FF02:0000:0000:0000:0000:0000:0000:00FB on interface 192.168.0.1/br0/14 May 16 14:57:17 [MDNS]: mDNSPlatformSendUDP got error 126 (Cannot assign requested address) sending packet to FF02:0000:0000:0000:0000:0000:0000:00FB on interface 192.168.0.1/br0/14 start_timer: start timer done TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: syslogd -L killall: inadyn: no process killed TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & failed to setup proxy: 3 [MLD]: mrib_mld_source: fget_wdev_by_idx: invalid idx(0) ailed to detect get_wdev_by_idx: invalid idx(0) local source addget_wdev_by_idx: invalid idx(0) ress on 14 [sysget_wdev_by_idx: invalid idx(0) tem]: rm -rf /etget_wdev_by_idx: invalid idx(0) c/ftpd.conf stget_wdev_by_idx: invalid idx(0) art_services: doget_wdev_by_idx: invalid idx(0) ne [system]: kiDriverOwn()::Return since already in Driver Own... llall bndstrg =============================== killall: bndstrgCurrent DevInfo Num: 0 : no process kil=============================== led [system]: i=============================== fconfig rai0 dowCurrent BssInfo Num: 0 n [system]: if=============================== config rai1 down=============================== ifconfig: iocCurrent StaRec Num: 0 tl 0x8913 failed=============================== : No such deviceAPWdsInitialize():WdsEntry[0] [system]: raliAPWdsInitialize():WdsEntry[1] nk_init make_wirAPWdsInitialize():WdsEntry[2] eless_config rtdAPWdsInitialize():WdsEntry[3] ev [system]: i[wifi_fwd_set_cb_num] band_cb_offset=33, recv_from_cb_offset=34 fconfig rai0 up CfgSetCountryRegion():region(9) out of range! E2pAccessMode=2 SSID[0]=WiFi, EdcaIdx=0 SSID[1]=dlink-guest-5GHz, EdcaIdx=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! [TxPower] BAND0: 100 [SKUenable] BAND0: 1 [PERCENTAGEenable] BAND0: 1 [BFBACKOFFenable] BAND0: 0 CalCacheApply = 0 APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = ABOVE HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 Top Init Done! Use alloc_skb RX[0] DESC a0ca0000 size = 8192 RX[1] DESC a0ca2000 size = 8192 Hif Init Done! ctl->txq = c2a931e8 ctl->rxq = c2a931f4 ctl->ackq = c2a93200 ctl->kickq = c2a9320c ctl->tx_doneq = c2a93218 ctl->rx_doneq = c2a93224 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2701): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(10302) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170424114041a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(460360) Build Date:_201711151010 Build Date:_201711151010 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201807252155 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000] NICReadEEPROMParameters():Calling eeinit NICReadEEPROMParameters: EEPROM 0x52 b313 NICReadEEPROMParameters: EEPROM 0x52 b313 Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(235): Don't Support this now! RTMPReadTxPwrPerRate(1382): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=85f6c434,Band=0,rfcap=3,channel=1,PhyMode=2 Band Rf: 1, Phy Mode: 2 AntCfgInit(2700): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtSingleSkuLoadParam: SINGLE SKU TABLE FILE /var/Wireless/7615_SingleSKU_5G.dat!!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: BF SKU TABLE FILE /var/Wireless/7615_BF_SKU_5G.dat!!! RtmpOSFileOpen(): Error 2 opening /var/Wireless/7615_BF_SKU_5G.dat EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2716): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c MtAsicSetMacMaxLen(1290): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=49/49, support 9 channels ApAutoChannelAtBootUp-----------------> MtCmdSetMacTxRx:(ret = 0) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [155] BW [2] from cetral freq [5785] i[37] offset [4538] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 149,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [155] BW [2] from cetral freq [5785] i[37] offset [4538] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [155] BW [2] from cetral freq [5785] i[37] offset [4538] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 157,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) [DfsSwitchCheck]: DFS ByPass TX calibration. mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [155] BW [2] from cetral freq [5785] i[37] offset [4538] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 161,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) ==================================================================== Channel 36 : Busy Time = 557, Skip Channel = FALSE, BwCap = TRUE Channel 40 : Busy Time = 236, Skip Channel = FALSE, BwCap = TRUE Channel 44 : Busy Time = 222, Skip Channel = FALSE, BwCap = TRUE Channel 48 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 149 : Busy Time = 1475, Skip Channel = FALSE, BwCap = TRUE Channel 153 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 157 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 161 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 48 Rule 3 Channel Busy time value : Min Channel Busy = 557 Rule 3 Channel Busy time value : BW = 80  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 48   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 48  ApAutoChannelAtBootUp<----------------- WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = xx:xx:xx:xx:xx:57 Current Channel is 48. DfsZeroWaitSupport=0 MtAsicSetChBusyStat(842): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=48 CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=49/49, support 9 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [RadarStateCheck]Set into RD_NORMAL_MODE MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=48, HT-CentCh=46, VHT-CentCh=42 mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [42] BW [2] from cetral freq [5220] i[9] offset [2d98] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) br0: port 4(eth2.1) entered forwarding state br0: port 3(eth2.2) entered forwarding state br0: port 2(eth2.3) entered forwarding state br0: port 1(eth2.4) entered forwarding state :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=48, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2) LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2595): Not support for HIF_MT yet! MtAsicSetPiggyBack(779): Not support for HIF_MT yet! MtAsicSetTxPreamble(2574): Not support for HIF_MT yet! RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! WifiFwdSet::disabled=0 ap_ftkd> Initialize FT KDP Module... BndStrg_Init() BndStrg_SetInfFlags(): BSS (xx:xx:xx:xx:xx:57) set 5G Inf rai0 ready. Main bssid = xx:xx:xx:xx:xx:57 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) fdb_enable() MCS Set = ff ff ff ff 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 Total allocated 4 WDS interfaces! WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Correct apidx from 0 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c273362c, len = 16 0x0000 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) [system]: iwpriv rai0 set IgmpSnEnable=1 [system]: iwpriv rai0 set WscUUID_E=d1087a18aae3b8153a5bxxxxxxxxxx55 [system]: iwpriv rai0 set WscUUID_Str=d1087a18-aae3-b815-3a5b-xxxxxxxxxx55 [system]: ifconfig ra0 down [system]: ifconfig ra1 down ifconfig: ioctl 0x8913 failed: No such device [system]: ralink_init make_wireless_config rt2860 [system]: ifconfig ra0 up get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) DriverOwn()::Return since already in Driver Own... =============================== Current DevInfo Num: 0 =============================== =============================== Current BssInfo Num: 0 =============================== =============================== Current StaRec Num: 0 =============================== APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] [wifi_fwd_set_cb_num] band_cb_offset=33, recv_from_cb_offset=34 E2pAccessMode=2 SSID[0]=WiFi, EdcaIdx=0 SSID[1]=dlink-guest, EdcaIdx=0 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! [TxPower] BAND0: 100 [SKUenable] BAND0: 1 [PERCENTAGEenable] BAND0: 1 [BFBACKOFFenable] BAND0: 0 CalCacheApply = 0 APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = ABOVE HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 Top Init Done! Use alloc_skb RX[0] DESC a0c12000 size = 8192 RX[1] DESC a0c14000 size = 8192 Hif Init Done! ctl->txq = c25931e8 ctl->rxq = c25931f4 ctl->ackq = c2593200 ctl->kickq = c259320c ctl->tx_doneq = c2593218 ctl->rx_doneq = c2593224 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2701): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(10302) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170424114041a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(460360) Build Date:_201711151010 Build Date:_201711151010 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201807252155 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] NICReadEEPROMParameters():Calling eeinit NICReadEEPROMParameters: EEPROM 0x52 b313 NICReadEEPROMParameters: EEPROM 0x52 b313 wait_action_idle: pid 1 preinit hold action lock 10 !!! Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(235): Don't Support this now! RTMPReadTxPwrPerRate(1382): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=87ff4434,Band=0,rfcap=3,channel=1,PhyMode=2 Band Rf: 1, Phy Mode: 2 AntCfgInit(2700): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtSingleSkuLoadParam: SINGLE SKU TABLE FILE /var/Wireless/7615_SingleSKU_24G.dat!!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: BF SKU TABLE FILE /var/Wireless/7615_BF_SKU_24G.dat!!! RtmpOSFileOpen(): Error 2 opening /var/Wireless/7615_BF_SKU_24G.dat EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2716): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c MtAsicSetMacMaxLen(1290): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels ApAutoChannelAtBootUp-----------------> MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [2] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [2] BW [0] from cetral freq [2422] i[44] offset [4b20] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [3] BW [0] from cetral freq [2422] i[44] offset [4b20] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [4] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [4] BW [0] from cetral freq [2422] i[44] offset [4b20] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [5] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [5] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [6] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [7] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [7] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [8] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [8] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [9] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [10] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [10] BW [0] from cetral freq [2462] i[46] offset [4cd0] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) ==================================================================== Channel 2 : Busy Time = 11014, Skip Channel = FALSE, BwCap = TRUE Channel 3 : Busy Time = 13398, Skip Channel = FALSE, BwCap = TRUE Channel 4 : Busy Time = 16400, Skip Channel = FALSE, BwCap = TRUE Channel 5 : Busy Time = 10099, Skip Channel = FALSE, BwCap = TRUE Channel 6 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 7 : Busy Time = 6488, Skip Channel = FALSE, BwCap = TRUE Channel 8 : Busy Time = 8344, Skip Channel = FALSE, BwCap = TRUE Channel 9 : Busy Time = 8473, Skip Channel = FALSE, BwCap = TRUE Channel 10 : Busy Time = 7337, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 6 Rule 3 Channel Busy time value : Min Channel Busy = 0 Rule 3 Channel Busy time value : BW = 20  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 14,Channel = 6   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 14,Channel = 6  ApAutoChannelAtBootUp<----------------- WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = xx:xx:xx:xx:xx:56 Current Channel is 6. DfsZeroWaitSupport=0 MtAsicSetChBusyStat(842): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6 CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels Enable 20/40 BSSCoex Channel Scan(BssCoex=1) MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [3] BW [0] from cetral freq [2422] i[44] offset [4b20] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [4] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [4] BW [0] from cetral freq [2422] i[44] offset [4b20] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) mt7615_apply_dcoc() : reload Central CH [5] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [5] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [6] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [7] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [7] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [8] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [8] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [9] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [10] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [10] BW [0] from cetral freq [2462] i[46] offset [4cd0] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [11] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [11] BW [0] from cetral freq [2462] i[46] offset [4cd0] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [12] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [12] BW [0] from cetral freq [2462] i[46] offset [4cd0] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 12,control_ch2=0, central_chl = 12 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [13] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [13] BW [0] from cetral freq [2462] i[46] offset [4cd0] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 13,control_ch2=0, central_chl = 13 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [RadarStateCheck]Set into RD_NORMAL_MODE MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 mt7615_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=6, HT-CentCh=6, VHT-CentCh=0 mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_dpd() : reload Central CH [6] BW [0] from cetral freq [2442] i[45] offset [4bf8] MtCmdGetTXDPDCalResult:(ret = 0) MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=6, HT-CentCh=6, VHT-CentCh=0, BBP_BW=0) LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2595): Not support for HIF_MT yet! MtAsicSetPiggyBack(779): Not support for HIF_MT yet! MtAsicSetTxPreamble(2574): Not support for HIF_MT yet! RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! WifiFwdSet::disabled=0 ap_ftkd> Initialize FT KDP Module... BndStrg_Init() BndStrg_SetInfFlags(): BSS (xx:xx:xx:xx:xx:56) set 2G Inf ra0 ready. Main bssid = xx:xx:xx:xx:xx:56 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) fdb_enable() MCS Set = ff ff ff ff 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw Total allocated 4 WDS interfaces! wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Correct apidx from 0 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c223362c, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 xx xx xx xx xx 56 [system]: iwpriv ra0 set IgmpSnEnable=1 [system]: iwpriv ra0 set WscUUID_E=d1087a18aae3b8153a5bxxxxxxxxxx55 [system]: iwpriv ra0 set WscUUID_Str=d1087a18-aae3-b815-3a5b-xxxxxxxxxx55 [system]: bndstrg -d 0 [14:57:55] [main]DebugLevel 0 [14:57:56] [main]Initialize bndstrg [14:57:56] [driver_wext_init]Initialize ralink wext interface @@@@ flag WIRELESS_2G ! channed=6 @@@@ flag WIRELESS_5G ! channed=48 OT> onetouch ver:1.5b202, StarterLib ver:1.4b189, idxmlLib ver:1.1b162, RssSpec ver:1.1 OT> RSS-HTTP Port=8008, ver:1.4b191 [system]: iwpriv rai0 set BndStrgCndPriority='0;1;D_SetCndChkFlag(): CndChkFlag = 0x10f 3;2;8' OT> Startup Services! OT> Startup..., intf:'br0', httpPort:5533, Cloning:Master OT> SD_SetCndChkFlag(): CndChkFlag = 0x10f EQ:2/2 [14:57:56][bndstrg_set_priority] [systeD_SetHoldTime(): HoldTime = 30000 m]: iwpriv rai0 set BndStrgCndChk=0x10f OT> UsD_SetHoldTime(): HoldTime = 30000 ing LAN interface 'br0', IP='192.168.0.1' RssEnD_SetRssiLow(): RssiLow = -80 cryptKey=aa3dd4fSet_BndStrg_RssiLow(): RssiLow = -80 890d6d72108a14a37e193f387 [14:57:56]SET_CHEK_COD_SetRssiLow(): RssiLow = -80 NDITIONS [systeSet_BndStrg_RssiLow(): RssiLow = -80 m]: iwpriv ra0 set BndStrgCndPriority='0;1;3;2;8' [14:57:56][bndstrg_set_priority] [system]: iwpriv ra0 set BndStrgCndChk=0x10f [14:57:56]SET_CHEK_CONDITIONS [system]: iwpriv rai0 set BndStrgHoldTime=30device ra0 entered promiscuous mode 000 [system]: br0: port 5(ra0) entered forwarding state iwpriv ra0 set Bbr0: port 5(ra0) entered forwarding state ndStrgHoldTime=30000 [system]: iwpriv rai0 setdevice rai0 entered promiscuous mode BndStrgRssiLow=br0: port 6(rai0) entered forwarding state -80 [system]: br0: port 6(rai0) entered forwarding state iwpriv ra0 set BndStrgRssiLow=-80 [system]: iwpriv ra0 set WscSetupLock=1 [system]: iwpriv rai0 set WscSetupLock=1 [system]: iwpriv ra0 set WscSetupLock=1 [system]: iwpriv rai0 set WscSetupLock=1 [system]: brctl addif br0 ra0 [system]: brctl addif br0 rai0 [system]: brctl addif br1 ra1 brctl: bridge br1: Invalid argument [system]: brctl addif br1 rai1 brctl: bridge br1: Invalid argument [system]: starter load wireless2g @@@@ flag WIRELESS_2G ! channed=6 [system]: starter load wireless5g @@@@ flag WIRELESS_5G ! [14:57:57] [bndstrg_event_handle][bndstrg_event_handle][INF_STATUS_RSP_2G:ra0]0,1 [14:57:57] [bndstrg_event_handle][bndstrg_event_handle][INF_STATUS_RSP_5G:rai0]0,1 channed=48 start_wlan()============>out start_schedule: enter Time synchronization has not been completed. We don't turn on scheduling. [system]: echo 1 > /proc/hw_nat/ipv6_hw_nat TRACE acl/acl.c: 116 upload_ping_block_rules: <--wan ping start--> [system]: iptables -t filter -D INPUT -j ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -F ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -X ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -N ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -A INPUT -j ACL_PING_INPUT 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE acl/acl.c: 129 upload_ping_block_rules: max_wan_num=1 [system]: iptables -t filter -A ACL_PING_INPUT -i eth3 -p ICMP -m state --state NEW -j DROP 2>/dev/null TRACE antiattack/antiattack.c: 996 TW_Anti_Spoofing_run: <--Anti Spoofing start--> [system]: iptables -t filter -F ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -X ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1002 TW_Anti_Spoofing_run: <--Anti Spoofing is disable--> TRACE firewallfilter/firewallfilter.c: 197 FIREWALL_FILTER_run: <--firewall filter start--> [system]: iptables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 236 FIREWALL_FILTER_run: firewall filter disabled TRACE firewallfilter/firewallfilter.c: 882 FIREWALL_IPv6_FILTER_run: <--firewall ipv6 filter start--> [system]: ip6tables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 927 FIREWALL_IPv6_FILTER_run: firewall ipv6 filter disabled TRACE macfilter/macfilter.c: 141 MACFILTER_run: <--mac filter start--> [system]: iptables -t filter -D FORWARD -j MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -N MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j MACFILTER_FORWARD 2>/dev/null ERROR macfilter/macfilter.c: 194 MACFILTER_run: mac filter rule is null TRACE urlfilter/urlfilter.c: 423 upload_url_filter_rules: <--url filter start--> ERROR urlfilter/urlfilter.c: 469 upload_url_filter_rules: url filter rule is null TRACE remotemange/remotemange.c: 105 REMOTEMANGE_run: <--remotemange start--> [system]: iptables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -X REMOTEMANGE_INPUT 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t filter -A REMOTEMANGE_INPUT -p TCP -i br+ --dport 443 -j ACCEPT TRACE remotemange/remotemange.c: 155 REMOTEMANGE_run: eth3,dhcp,wan_wan0_ ERROR remotemange/remotemange.c: 160 REMOTEMANGE_run: wan ip is null TRACE virtualserver/virtualserver.c: 231 VIRTUALSERVER_run: <--virtualserver start--> [system]: iptables -t nat -D PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -F VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -X VIRTUALSERVER_FORWARD 2>/dev/null [system]: cat /proc/net/arp|awk '/0x6/{print $0}'|awk '/^[1-9]/{print "arp -d " $1}' | sh -x [system]: iptables -t nat -N VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -A PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -N VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -N VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE virtualserver/virtualserver.c: 292 VIRTUALSERVER_run: eth3,dhcp,wan_wan0_ ERROR virtualserver/virtualserver.c: 296 VIRTUALSERVER_run: wan ip is null ERROR virtualserver/virtualserver.c: 60 WOL_Rule_Run: WOL rule is null TRACE portforward/portforward.c: 177 PORTFORWARD_run: <--portforward start--> [system]: iptables -t nat -D PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -F PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -X PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t nat -N BndStrg_Enable(): Band steering start running. PORTFORWARD_PRERD_SetCndChkFlag(): CndChkFlag = 0x10f OUTING 2>/dev/nuBndStrg_Enable(): Band steering start running. ll [system]: iD_SetCndChkFlag(): CndChkFlag = 0x10f ptables -t nat -A PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -N PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [14:57:58] [BndStrg_status_polling]BndStrg_status_polling(): table->dbdc_mode=0,table->Band=0 [14:57:58] [BndStrg_status_polling]BndStrg_status_polling(): bndstrg->table.b2GInfDiable_by_drv=0 [14:57:58] [BndStrg_status_polling]BndStrg_status_polling(): bndstrg->table.b5GInfDiable_by_drv=0 [14:57:58] [driver_wext_bndstrg_onoff]driver_wext_bndstrg_onoff [14:57:58] [driver_wext_bndstrg_onoff]driver_wext_bndstrg_onoff [14:57:58]onoff = 1,band = 2 [14:57:58]SET_CHEK_CONDITIONS [14:57:58][bndstrg_set_priority] [14:57:58]onoff = 1,band = 1 [14:57:58]SET_CHEK_CONDITIONS [14:57:58][bndstrg_set_priority] [system]: iptables -t filter -N PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j PORTFORWARD_FORWARD 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE portforward/portforward.c: 238 PORTFORWARD_run: eth3,dhcp,wan_wan0_ ERROR portforward/portforward.c: 242 PORTFORWARD_run: wan ip is null TRACE dmz/dmz.c: 151 DMZ_run: <--dmz start--> [system]: iptables -t nat -D PREROUTING -j DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -F DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -X DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j DMZ_POSTROUTING 2>/dev/null [system]: iptables -t nat -F DMZ_POSTROUTING 2>/dev/null [system]: iptables -t nat -X DMZ_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j DMZ_FORWARD 2>/dev/null [system]: iptables -t filter -F DMZ_FORWARD 2>/devnf_conntrack_rtsp v0.7 loading /null [system]: iptables -t nat -X DMZ_FORWARD 2>/dev/null nf_nat_rtsp v0.7 loading [0;32;32mTRACE miniupnpd/miniupnpd.c: 583 iptables_upnp_run: <--iptables upnp start--> TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE miniupnpd/miniupnpd.c: 601 iptables_upnp_run: eth3,dhcp,wan_wan0_ [system]: iptables -t nat -F MINIUPNPD 2>/dev/null [system]: iptables -t nat -D PREROUTING -i eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t nat -X MINIUPNPD 2>/dev/null [system]: iptables -t filter -F MINIUPNPD 2>/dev/null [system]: iptables -t filter -D FORWARD -i eth3 ! -o eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t filter -X MINIUPNPD 2>/dev/null [system]: iptables -t nat -N MINIUPNPD 2>/dev/null [system]: iptables -t nat -A PREROUTING -i eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t filter -N MINIUPNPD 2>/dev/null [system]: iptables -t filter -A FORWARD -i eth3 ! -o eth3 -j MINIUPNPD 2>/dev/null creat_miniupnpd_iptables: enter creat_miniupnpd_iptables TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -F PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -D PREROUTING -i eth3 -j PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -X PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -N PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PREROUTING -i eth3 -j PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -m state --state RELATED,ESTABLISHED -j ACCEPT 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -j DROP 2>/dev/null [system]: iptables -t filter -N ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -F ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -A FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_rtsp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko 2>/dev/null [system]: iptables -t filter -D INPUT -j WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -F WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -X WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -D FORWARD -j WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -F WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -X WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -N WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -A INPUT -j WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.0.1 --dport 80 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.0.1 --dport 443 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.7.1 --dport 80 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.7.1 --dport 443 -j DROP 2>/dev/null [system]: iptables -t filter -N WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -I FORWARD -j WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_FORWARD -i br1 -o br0 -m state --state NEW -j DROP 2>/dev/null [system]: iptables -t filter -D INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -F GRC_INPUT 2>/dev/null [system]: iptables -t filter -X GRC_INPUT 2>/dev/null [system]: iptables -t filter -N GRC_INPUT 2>/dev/null [system]: iptables -t filter -I INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -m state --state INVALID -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 0 -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 1 -j DROP 2>/dev/null [system]: iptables -t filter -D FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: iptables -t filter -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: ip6tables -t filter -D FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: ip6tables -t filter -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null TRACE antiattack/antiattack.c:1205 TW_Spi_Fw_Config: <--spi firewall start--> [system]: iptables -t filter -F SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -F SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -F SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D INPUT -j SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -D PREROUTING -j SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 [system]: iptables -t filter -X SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -X SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -X SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1175 TW_IPv6_Ingress_Filtering_Config: <--IPv6 ingress filtering start--> [system]: ip6tables -t filter -F INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -D FORWARD -j INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -X INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1181 TW_IPv6_Ingress_Filtering_Config: <--IPv6 ingress filtering start is disable--> TRACE antiattack/antiattack.c:1112 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security start--> [system]: ip6tables -t filter -F SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -D FORWARD -j SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -X SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1118 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security is disable--> TRACE acl/acl.c: 332 MASQUERADENAT_run: <--MASQUERADENAT start--> [system]: iptables -t nat -F POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -X POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -N POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.0.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.7.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t mangle -D PREROUTING -j QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -D POSTROUTING -j QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_POSTROUTING 2>/dev/null [system]: tc qdisc del dev imq0 root 2>/dev/null [system]: tc qdisc del dev imq1 root 2>/dev/null [system]: ifconfig imq0 down [system]: ifconfig imq1 down [system]: insmod -q hw_nat insmod: cannot insert '/lib/modules/3.10.14+/kernel/net/nat/hw_nat/hw_nat.ko': File exists [system]: iwpriv ra0 set hw_nat_register=1 [system]: iwpriv rai0 set hw_nat_register=1 TRACE qos/qos.c: 290 QOS_start: QosManagementType=Off TRACE qos/qos.c: 306 QOS_start: qos is disabled TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: /sbin/flush_conntrack & TEST: flush conntrack (OK) [system]: ip6tables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -X REMOTEMANGE_INPUT 2>/dev/null sWan_status=Disconnected, sWan_ifname=eth3, sWan_ip=. [system]: ip6tables -t filter -A REMOTEMANGE_INPUT ! -i br+ -p TCP -m multiport --dports 80,443 -j DROP [system]: gpio l 8 0 4000 0 0 0 [system]: gpio l 16 4000 0 1 0 4000 eth2/eth3 RPS: CPU0/2 /sbin/smp.sh: line 219: cannot create /sys/class/net/apclie0/queues/rx-0/rps_cpus: nonexistent directory set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 init_main: recv signal 16 from pid [445:] (from user) set_action: 1: set_action 11 handle_notifications: cmd[0]=restart_wanall ======>running: 3 wanall stop_radvd: done stop_dhcp6s: done TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ wan_ifname:eth3 prefix:wan_wan0_ wan_down: eth3 dhcp [system]: killall -9 omcproxy [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ failed to setup proxy: 3 eth3: No such process del_ns: enter [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async [system]: echo 1 > /proc/net/arp_spoofing_enable stop_miniupnpd: stop_miniupnpd ----- [system]: ipsec setup stop Stopping Openswan IPsec... stop ordered, but IPsec appears to be already stopped! doing cleanup anyway... wan_down: done [system]: killall ripd killall: ripd: no process killed [system]: killall zebra killall: zebra: no process killed [system]: iptables -t nat -D PREROUTING -p udp --sport 520 --dport 520 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?). ppp0: No such device ppp1: No such device stop_wan: done stop_dslite_tunnel pswan4proto=dhcp [system]: killall -9 omcproxy [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & failed to setup proxy: 3 [system]: killall -HUP pppd killall: pppd: no process killed [system]: killall -TERM pppd killall: pppd: no process killed [system]: ip -6 r del /0 dev eth3 Error: an inet prefix is expected rather than "/0". [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP ip6tables: Bad rule (does a matching rule exist in that chain?). [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -F SOURCE_ADeth3: ===> VirtualIF_close DRESS_CHECK_FORWbr0: port 6(rai0) entered disabled state ARD ip6tables:br0: port 5(ra0) entered disabled state No chain/targetbr0: port 4(eth2.1) entered disabled state /match by that nbr0: port 3(eth2.2) entered disabled state ame. [system]: br0: port 2(eth2.3) entered disabled state ip6tables -t filbr0: port 1(eth2.4) entered disabled state ter -D FORWARD -br0: port 6(rai0) entered forwarding state i br0 -j SOURCE_br0: port 6(rai0) entered forwarding state ADDRESS_CHECK_FObr0: port 5(ra0) entered forwarding state RWARD ip6tablebr0: port 5(ra0) entered forwarding state s v1.4.20: Couldbr0: port 4(eth2.1) entered forwarding state n't find target br0: port 4(eth2.1) entered forwarding state `SOURCE_ADDRESS_br0: port 3(eth2.2) entered forwarding state CHECK_FORWARD' br0: port 3(eth2.2) entered forwarding state Try `ip6tablesbr0: port 2(eth2.3) entered forwarding state -h' or 'ip6tablbr0: port 2(eth2.3) entered forwarding state es --help' for mbr0: port 1(eth2.4) entered forwarding state ore information.br0: port 1(eth2.4) entered forwarding state [system]: ip6tables -t filter -X SOURCE_ADDRESS_CHECK_FORWARD ip6tables: No chain/target/match by that name. stop_wan6: stop_wan6 done start_lan_ipv6: enter p= start_dhcp6s: done start_radvd: done [system]: dxmlc -s /uplink/ip '' [system]: dxmlc -s /uplink/netmask '' [system]: dxmlc -s /upeth3: ===> VirtualIF_open link/gateway '' [system]: dxmlc -s /uplink/dns '' start_wan: eth3 dhcp start_wan: eth3 dhcp,prefix=wan_wan0_,ins_suffixbuf=0_ wait_action_idle: pid 1 preinit hold action lock 11 !!! start_wan: the tmp=/var/run/udhcpc-wan_wan0_.pid [system]: /sbin/pppoe-relay -S eth3 -C br0 & TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ main: ***wan_udhcpc start*** [system]: zebra -u admin -g admin -f /tmp/zebra.conf -d wan_ifname =eth3 wan_ifname:eth3 prefix:wan_wan0_ wan_down: eth3 dhcp [system]: killall -9 omcproxy [system]: iptables -t nat -I PREROUTING -p udp --sport 520 --dport 520 -j ACCEPT [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: ripd -u admin -g admin -f /tmp/ripd.conf -d del_ns: enter [system]: rm -f /tmp/dnsmasq_dhcp_event start_wan6: service=3 start_wan6: prefix=wan_wan0_ [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP start_wan6: start_wan6 done handle_notifications: done set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 main: ***dhcp6c start*** init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable stop_miniupnpd: stop_miniupnpd ----- [system]: ipsec setup stop wan_down: done [system]: starter load uplink deconfig: done main: ***wan_udhcpc done*** deconfig6: start stop_dslite_tunnel pswan4proto=dhcp [system]: killall -9 omcproxy init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & main: ***wan_udhcpc start*** init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable [system]: ip6tables -t filter -F SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br0 -j SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -X SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP deconfig6: stop_wan6 done main: ***dhcp6c done*** bound: iRenew=0,wan_ifname=eth3 bound: ip change new 10.0.0.99 bound: subnet change new 255.255.255.0 bound: router change new 10.0.0.254 bound: dns change new 10.0.0.254 lan_wan_ip_conflict_handler: ====>enter lan_wan_ip_conflict_handler: ====>done wan_up: eth3 wan_up: eth3 dhcp [system]: route add -host 10.0.0.254 netmask 0.0.0.0 dev eth3 tw_sroute init in eth3 tw_sroute init out add_ns: enter init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable miniupnpd: enter miniupnpd ----- start_miniupnpd_finish: start_miniupnpd ----- [system]: miniupnpd -f /tmp/miniupnpd/miniupnpd.conf -G & miniupnpd: miniupnpd end init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: echo 1 > /proc/hw_nat/ipv6_hw_nat TRACE acl/acl.c: 116 upload_ping_block_rules: <--wan ping start--> [system]: iptables -t filter -D INPUT -j ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -F ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -X ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -N ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -A INPUT -j ACL_PING_INPUT 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE acl/acl.c: 129 upload_ping_block_rules: max_wan_num=1 [system]: iptables -t filter -A ACL_PING_INPUT -i eth3 -p ICMP -m state --state NEW -j DROP 2>/dev/null TRACE antiattack/antiattack.c: 996 TW_Anti_Spoofing_run: <--Anti Spoofing start--> [system]: iptables -t filter -F ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -X ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1002 TW_Anti_Spoofing_run: <--Anti Spoofing is disable--> TRACE firewallfilter/firewallfilter.c: 197 FIREWALL_FILTER_run: <--firewall filter start--> [system]: iptables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 236 FIREWALL_FILTER_run: firewall filter disabled TRACE firewallfilter/firewallfilter.c: 882 FIREWALL_IPv6_FILTER_run: <--firewall ipv6 filter start--> [system]: ip6tables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 927 FIREWALL_IPv6_FILTER_run: firewall ipv6 filter disabled TRACE macfilter/macfilter.c: 141 MACFILTER_run: <--mac filter start--> [system]: iptables -t filter -D FORWARD -j MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -N MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j MACFILTER_FORWARD 2>/dev/null ERROR macfilter/macfilter.c: 194 MACFILTER_run: mac filter rule is null TRACE urlfilter/urlfilter.c: 423 upload_url_filter_rules: <--url filter start--> ERROR urlfilter/urlfilter.c: 469 upload_url_filter_rules: url filter rule is null TRACE remotemange/remotemange.c: 105 REMOTEMANGE_run: <--remotemange start--> [system]: iptables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -X REMOTEMANGE_INPUT 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t filter -A REMOTEMANGE_INPUT -p TCP -i br+ --dport 443 -j ACCEPT TRACE remotemange/remotemange.c: 155 REMOTEMANGE_run: eth3,dhcp,wan_wan0_ [system]: iptables -t filter -I REMOTEMANGE_INPUT -p TCP -d 10.0.0.99 --dport 80 -j DROP [system]: iptables -t filter -I REMOTEMANGE_INPUT -p TCP -d 10.0.0.99 --dport 443 -j DROP TRACE virtualserver/virtualserver.c: 231 VIRTUALSERVER_run: <--virtualserver start--> [system]: iptables -t nat -D PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -F VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -X VIRTUALSERVER_FORWARD 2>/dev/null [system]: cat /proc/net/arp|awk '/0x6/{print $0}'|awk '/^[1-9]/{print "arp -d " $1}' | sh -x [system]: iptables -t nat -N VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -A PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -N VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -N VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE virtualserver/virtualserver.c: 292 VIRTUALSERVER_run: eth3,dhcp,wan_wan0_ ERROR virtualserver/virtualserver.c: 304 VIRTUALSERVER_run: virtualserver rule is null TRACE portforward/portforward.c: 177 PORTFORWARD_run: <--portforward start--> [system]: iptables -t nat -D PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -F PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -X PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t nat -N PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -A PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -N PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t filter -N PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j PORTFORWARD_FORWARD 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE portforward/portforward.c: 238 PORTFORWARD_run: eth3,dhcp,wan_wan0_ ERROR portforward/portforward.c: 250 PORTFORWARD_run: portfoward rule is null TRACE dmz/dmz.c: 151 DMZ_run: <--dmz start--> [system]: iptables -t nat -D PREROUTING -j DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -F DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -X DMZ_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j DMZ_POSTROUTING 2>/dev/null [system]: iptables -t nat -F DMZ_POSTROUTING 2>/dev/null [system]: iptables -t nat -X DMZ_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j DMZ_FORWARD 2>/dev/null [system]: iptables -t filter -F DMZ_FORWARD 2>/dev/null [system]: iptables -t nat -X DMZ_FORWARD 2>/dev/null TRACE miniupnpd/miniupnpd.c: 583 iptables_upnp_run: <--iptables upnp start--> TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE miniupnpd/miniupnpd.c: 601 iptables_upnp_run: eth3,dhcp,wan_wan0_ [system]: iptables -t nat -F MINIUPNPD 2>/dev/null [system]: iptables -t nat -D PREROUTING -i eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t nat -X MINIUPNPD 2>/dev/null [system]: iptables -t filter -F MINIUPNPD 2>/dev/null [system]: iptables -t filter -D FORWARD -i eth3 ! -o eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t filter -X MINIUPNPD 2>/dev/null [system]: iptables -t nat -N MINIUPNPD 2>/dev/null [system]: iptables -t nat -A PREROUTING -i eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t filter -N MINIUPNPD 2>/dev/null [system]: iptables -t filter -A FORWARD -i eth3 ! -o eth3 -j MINIUPNPD 2>/dev/null creat_miniupnpd_iptables: enter creat_miniupnpd_iptables TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -F PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -D PREROUTING -i eth3 -j PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -X PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -N PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PREROUTING -i eth3 -j PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -m state --state RELATED,ESTABLISHED -j ACCEPT 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -j DROP 2>/dev/null [system]: iptables -t filter -N ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -F ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -A FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_rtsp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko 2>/dev/null [system]: iptables -t filter -D INPUT -j WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -F WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -X WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -D FORWARD -j WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -F WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -X WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -N WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -A INPUT -j WLAN_GUEST_LOGIN_INPUT 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.0.1 --dport 80 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.0.1 --dport 443 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.7.1 --dport 80 -j DROP 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_INPUT -i br1 -p tcp -d 192.168.7.1 --dport 443 -j DROP 2>/dev/null [system]: iptables -t filter -N WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -I FORWARD -j WLAN_GUEST_LOGIN_FORWARD 2>/dev/null [system]: iptables -t filter -A WLAN_GUEST_LOGIN_FORWARD -i br1 -o br0 -m state --state NEW -j DROP 2>/dev/null [system]: iptables -t filter -D INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -F GRC_INPUT 2>/dev/null [system]: iptables -t filter -X GRC_INPUT 2>/dev/null [system]: iptables -t filter -N GRC_INPUT 2>/dev/null [system]: iptables -t filter -I INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -m state --state INVALID -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 0 -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 1 -j DROP 2>/dev/null [system]: iptables -t filter -D FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: iptables -t filter -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: ip6tables -t filter -D FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: ip6tables -t filter -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null TRACE antiattack/antiattack.c:1205 TW_Spi_Fw_Config: <--spi firewall start--> [system]: iptables -t filter -F SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -F SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -F SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D INPUT -j SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -D PREROUTING -j SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 [system]: iptables -t filter -X SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -X SPI_FIREWALL_INPUT 2>/dev/null 1>&2 [system]: iptables -t nat -X SPI_FIREWALL_PREROUTING 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1175 TW_IPv6_Ingress_Filtering_Config: <--IPv6 ingress filtering start--> [system]: ip6tables -t filter -F INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -D FORWARD -j INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -X INGRESS_FILTERING_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1181 TW_IPv6_Ingress_Filtering_Config: <--IPv6 ingress filtering start is disable--> TRACE antiattack/antiattack.c:1112 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security start--> [system]: ip6tables -t filter -F SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -D FORWARD -j SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -X SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1118 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security is disable--> TRACE acl/acl.c: 332 MASQUERADENAT_run: <--MASQUERADENAT start--> [system]: iptables -t nat -F POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -X POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -N POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.0.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.7.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t mangle -D PREROUTING -j QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -D POSTROUTING -j QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_POSTROUTING 2>/dev/null [system]: tc qdisc del dev imq0 root 2>/dev/null [system]: tc qdisc del dev imq1 root 2>/dev/null [system]: ifconfig imq0 down [system]: ifconfig imq1 down [system]: insmod -q hw_nat [system]: iwpriv ra0 set hw_nat_register=1 [system]: iwpriv rai0 set hw_nat_register=1 TRACE qos/qos.c: 290 QOS_start: QosManagementType=Off TRACE qos/qos.c: 306 QOS_start: qos is disabled TRACE public/public.c: 622 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 628 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: /sbin/flush_conntrack & init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: ipsec setup stop ERROR services.c:2832 start_quick_vpn: Quick vpn now is disabled start_wan6: service=3 start_wan6: prefix=wan_wan0_ [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 start_wan6: start_wan6 done TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ main: ***dhcp6c start*** TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: fota --action query --fw-encrypt & main: ***dhcp6c start*** [system]: killall time_client [system]: time_client --action daemon & wan_up: done bound: done main: ***wan_udhcpc done*** deconfig6: start stop_dslite_tunnel pswan4proto=dhcp [system]: killall -9 omcproxy init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable [system]: ip6tables -t filter -F SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br0 -j SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -X SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP deconfig6: stop_wan6 done main: ***dhcp6c done*** deconfig6: start stop_dslite_tunnel pswan4proto=dhcp [system]: killall -9 omcproxy init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable [system]: ip6tables -t filter -F SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br0 -j SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -X SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -A FORWARD -i br+ -o eth3 -j DROP deconfig6: stop_wan6 done main: ***dhcp6c done*** init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 notify_rc_internal: <rc_service> [fota_output] 2031:notify_rc restart_mdns init_main: recv signal 16 from pid [2031:] (from user) set_action: 1: set_action 11 handle_notifications: cmd[0]=restart_mdns ======>running: 3 mdns main: ***ntp_sync_event start*** ntp_sync_event: enter [system]: killall mdnsd [system]: rm -rf /tmp/schedule/ killall: mdnsd: no process killed start_mdns_responder: enter start_schedule: enter major_ver:1,minor_ver:20 fota_major_ver:1,fota_minor_ver:30 [system]: mDNSResponder -b -i br0 -f /tmp/mdns_resp.conf -e dlinkrouter -e dlinkrouterEF55 start_schedule: exit ntp_sync_event: done main: ***ntp_sync_event done*** [system]: mdnsd sh: mdnsd: not found start_mdns_responder: done handle_notifications: done set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 main: ***dhcp6c start*** ****** RA_HOPLIMIT =64 RA_MTU =1500 PREFIXES =2403:5800:3101:50c::/62,74,2208,3208,class=00000000 fd9f:c4f1:9937:c::/62,74,4294967295,4294967295,class=00000000 PREFIXES_VALID =-1 PREFIXES_PREFERRED =-1 RDNSS =fd9f:c4f1:9937::1 ADDRESSES =2403:5800:3101:500::572/128,0,2208,3208 fd9f:c4f1:9937::572/128,0,4294967295,4294967295 RA_ADDRESSES =2403:5800:3101:500:7a32:1bff:fe61:ef58/64,0,2210,3210 fd9f:c4f1:9937:0:7a32:1bff:fe61:ef58/64,0,4294967295,4294967295 AFTR = ****** wan_ifname=eth3 ****** p=2403:5800:3101:50c:7a32:1bff:fe61:ef55 [system]: ip6tables -t filter -D FORWARD -i br+ -o eth3 -j DROP [system]: ip6tables -t filter -F SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -D FORWARD -i br0 -j SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -X SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -N SOURCE_ADDRESS_CHECK_FORWARD [system]: ip6tables -t filter -A SOURCE_ADDRESS_CHECK_FORWARD -i br0 -s 2403:5800:3101:50c::/62 -j RETURN [system]: ip6tables -t filter -A SOURCE_ADDRESS_CHECK_FORWARD -i br0 -j REJECT --reject-with=icmp6-source-addr-fail [system]: ip6tables -t filter -I FORWARD -i br0 -j SOURCE_ADDRESS_CHECK_FORWARD init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: rm -f /tmp/dnsmasq_dhcp_event TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: dnsmasq -C /tmp/dnsmasq.conf -6 /tmp/dnsmasq_dhcp_event --log-async init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: echo 1 > /proc/net/arp_spoofing_enable init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) stop_radvd: done init_main: UNKNOWN set_action: 1: set_action 0 start_dhcp6s: done [system]: dhcp6ctl -S -k /tmp/dhcp6sctlkey reload start_radvd: done start_dslite_tunnel pswan4proto=dhcp init_main: recv signal 14 from pid [1:/sbin/preinit] (from user) init_main: UNKNOWN set_action: 1: set_action 0 [system]: omcproxy -e3 eth3,br0,br2,br3,scope=realm & [system]: ip6tables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -X REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -A REMOTEMANGE_INPUT -i br+ ! -d 2403:5800:3101:500::572 -p TCP --dport 80 -j ACCEPT [system]: ip6tables -t filter -A REMOTEMANGE_INPUT -i br+ ! -d 2403:5800:3101:500::572 -p TCP --dport 443 -j ACCEPT [system]: ip6tables -t filter -A REMOTEMANGE_INPUT -p TCP -m multiport --dports 80,443 -j DROP main: ***dhcp6c done*** br0: port 6(rai0) entered forwarding state br0: port 5(ra0) entered forwarding state br0: port 4(eth2.1) entered forwarding state br0: port 3(eth2.2) entered forwarding state br0: port 2(eth2.3) entered forwarding state br0: port 1(eth2.4) entered forwarding state Fota time is not set, select random time 3:48.


=================================================================== MT7621 stage1 code 10:33:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x9, 1/0 = 514/510 25000000 PLL4 FB_DL: 0xf, 1/0 = 521/503 3D000000 PLL2 FB_DL: 0x18, 1/0 = 577/447 61000000 do DDR setting..[01F40000] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 80 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00002221 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 7 8 11 7 7 9 6 6 7 10 | 8 9 9 10 10 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =33 DQS1 = 34 ================================================================== bit DQS0 bit DQS1 0 (1~65)33 8 (1~62)31 1 (1~63)32 9 (1~62)31 2 (1~60)30 10 (0~62)31 3 (1~66)33 11 (1~62)31 4 (1~64)32 12 (1~66)33 5 (1~63)32 13 (1~62)31 6 (1~64)32 14 (2~66)34 7 (1~65)33 15 (1~64)32 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 8 11 11 8 8 10 6 9 10 10 | 11 12 10 13 10 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0080 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot 1.1.3 (Jul 19 2017 - 20:51:21) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb4000 Config XHCI 40M PLL flash manufacture id: ef, device id 40 18 find flash: W25Q128BV *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jul 19 2017 Time:20:51:21 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 6: System Enter UBoot to Update Img or Bin. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 0 3: System Boot system code via Flash. ## Booting image at bc060000 ... Image Name: MIPS OpenWrt Linux-5.4.52 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2334284 Bytes = 2.2 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... [ 0.000000] Linux version 5.4.52 (lucky@6600K) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13958-bcd7a0c095)) #0 SMP Mon Jul 27 18:15:10 2020 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is D-Link DIR-878 A1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26672 r8192 d22480 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00000025 [ 0.000000] Readback ErrCtl register=00000025 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 121040K/131072K available (5563K kernel code, 197K rwdata, 1216K rodata, 1268K init, 230K bss, 10032K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x550 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015477] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.055831] pid_max: default: 32768 minimum: 301 [ 0.065169] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.079574] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097656] rcu: Hierarchical SRCU implementation. [ 0.107749] smp: Bringing up secondary CPUs ... [ 0.118284] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.118293] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.118305] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.118406] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.144931] Synchronize counters for CPU 1: done. [ 0.215632] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.215640] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.215648] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.215702] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.243470] Synchronize counters for CPU 2: done. [ 0.304556] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.304564] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.304571] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.304628] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.331073] Synchronize counters for CPU 3: done. [ 0.390676] smp: Brought up 1 node, 4 CPUs [ 0.402978] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.422282] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.436218] pinctrl core: initialized pinctrl subsystem [ 0.447992] NET: Registered protocol family 16 [ 0.482474] random: fast init done [ 0.489306] clocksource: Switched to clocksource GIC [ 0.501182] NET: Registered protocol family 2 [ 0.510460] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.526990] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.542174] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.556163] TCP: Hash tables configured (established 1024 bind 1024) [ 0.568898] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.581801] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.595830] NET: Registered protocol family 1 [ 0.604399] PCI: CLS 0 bytes, default 32 [ 0.701223] 4 CPUs re-calibrate udelay(lpj = 1163264) [ 0.712717] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.736701] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.748186] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.770294] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.781636] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.792940] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.804709] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.818684] printk: console [ttyS0] disabled [ 0.827146] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.845069] printk: console [ttyS0] enabled [ 0.845069] printk: console [ttyS0] enabled [ 0.861626] printk: bootconsole [early0] disabled [ 0.861626] printk: bootconsole [early0] disabled [ 0.883078] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.905583] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.915198] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.927854] Creating 4 MTD partitions on "spi0.0": [ 0.937411] 0x000000000000-0x000000030000 : "u-boot" [ 0.948553] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.960353] 0x000000040000-0x000000060000 : "factory" [ 0.971651] 0x000000060000-0x000001000000 : "firmware" [ 0.983390] 2 sge-fw partitions found on MTD device firmware [ 0.994715] Creating 2 MTD partitions on "firmware": [ 1.004615] 0x000000000000-0x000000239eec : "kernel" [ 1.015615] 0x000000239eec-0x000000fa0000 : "rootfs" [ 1.026554] mtd: device 5 (rootfs) set to be root filesystem [ 1.037952] 1 squashfs-split partitions found on MTD device rootfs [ 1.050279] 0x000000540000-0x000000fa0000 : "rootfs_data" [ 1.063117] libphy: Fixed MDIO Bus: probed [ 1.095593] libphy: mdio: probed [ 1.102242] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.115519] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 1.134123] mt7621-pci 1e140000.pcie: Parsing DT failed [ 1.147120] NET: Registered protocol family 10 [ 1.157736] Segment Routing with IPv6 [ 1.165154] NET: Registered protocol family 17 [ 1.174332] 8021q: 802.1Q VLAN Support v1.8 [ 1.184499] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.209132] libphy: dsa slave smi: probed [ 1.217581] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 1.235497] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 1.253456] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 1.271356] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 1.289402] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 1.307205] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 1.324733] DSA: tree 0 setup [ 1.331049] rt2880-pinmux pinctrl: pcie is already enabled [ 1.342012] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 1.357065] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 1.371991] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.486624] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.497745] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.608657] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.622536] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.632254] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.641985] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.660699] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.673390] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.687093] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.700796] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.711771] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.723784] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.736281] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.748842] pci 0000:00:00.0: supports D1 [ 1.756835] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.768686] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.780700] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.793221] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.805779] pci 0000:00:01.0: supports D1 [ 1.813771] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.826509] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.842491] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.858664] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 1.870698] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 1.884393] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.913254] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.923679] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.935826] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.949361] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.963759] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.977147] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 1.989190] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 2.002911] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 2.031741] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 2.042178] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 2.054329] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 2.067861] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 2.082261] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.095501] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 2.108690] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.122576] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 2.135756] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.149634] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.163163] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 2.177561] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 2.191091] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 2.205488] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 2.219023] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 2.232555] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 2.246092] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 2.259639] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.274218] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.284112] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 2.297644] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.311171] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 2.325574] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 2.340147] pci 0000:00:01.0: PCI bridge to [bus 02] [ 2.350045] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 2.363576] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 2.377102] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 2.392202] hctosys: unable to open rtc device (rtc0) [ 2.402958] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 2.421447] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 2.439812] Freeing unused kernel memory: 1268K [ 2.448857] This architecture does not have kernel memory protection. [ 2.461683] Run /sbin/init as init process [ 3.038773] init: Console is alive [ 3.045827] init: - watchdog - [ 3.635487] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.733654] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.749563] init: - preinit - [ 4.322838] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 4.338937] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.355821] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4.502576] random: jshn: uninitialized urandom read (4 bytes read) [ 4.569607] random: jshn: uninitialized urandom read (4 bytes read) [ 4.617925] random: jshn: uninitialized urandom read (4 bytes read) [ 4.778888] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 4.792511] 8021q: adding VLAN 0 to HW filter on device lan1 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.877753] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 7.892717] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 9.020664] jffs2: notice: (551) jffs2_build_xattr_subsystem: complete building xattr subsystem, 13 of xdatum (0 unchecked, 4 orphan) and 15 of xref (1 dead, 3 orphan) found. [ 9.053472] mount_root: switching to jffs2 overlay [ 9.080436] overlayfs: upper fs does not support tmpfile. [ 9.096193] urandom-seed: Seeding with /etc/urandom.seed [ 9.186893] mt7530 mdio-bus:1f lan1: Link is Down [ 9.206586] procd: - early - [ 9.212443] procd: - watchdog - [ 9.805365] procd: - watchdog - [ 9.811961] procd: - ubus - [ 9.901922] urandom_read: 5 callbacks suppressed [ 9.901934] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.924756] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.938932] procd: - init - Please press Enter to activate this console. [ 10.368113] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.396039] Loading modules backported from Linux version v5.8-rc2-0-g48778464bb7d [ 10.411286] Backport generated by backports.git v5.8-rc2-1-0-g7a69429b [ 10.442404] xt_time: kernel timezone is -0000 [ 10.507529] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 10.518356] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 10.529649] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 10.558953] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 10.569784] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 10.574101] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 10.574101] [ 10.581095] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 10.641792] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 10.641792] [ 10.674362] PPP generic driver version 2.4.2 [ 10.686719] NET: Registered protocol family 24 [ 10.715957] kmodloader: done loading kernel modules from /etc/modules.d/* [ 10.718553] urngd: v1.0.2 started. [ 10.881792] mt7615e 0000:01:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812 [ 10.884265] mt7615e 0000:02:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812 [ 10.961301] random: crng init done [ 11.005043] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 11.005161] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 16.258175] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 16.279529] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 16.295684] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 16.299781] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 16.327750] 8021q: adding VLAN 0 to HW filter on device lan1 [ 16.343835] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.357937] br-lan: port 1(lan1) entered blocking state [ 16.368506] br-lan: port 1(lan1) entered disabled state [ 16.380490] device lan1 entered promiscuous mode [ 16.389905] device eth0 entered promiscuous mode [ 16.429433] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 16.444851] 8021q: adding VLAN 0 to HW filter on device lan2 [ 16.460095] br-lan: port 2(lan2) entered blocking state [ 16.470665] br-lan: port 2(lan2) entered disabled state [ 16.482968] device lan2 entered promiscuous mode [ 16.504560] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 16.519588] 8021q: adding VLAN 0 to HW filter on device lan3 [ 16.534833] br-lan: port 3(lan3) entered blocking state [ 16.545393] br-lan: port 3(lan3) entered disabled state [ 16.558124] device lan3 entered promiscuous mode [ 16.577591] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 16.591446] 8021q: adding VLAN 0 to HW filter on device lan4 [ 16.606640] br-lan: port 4(lan4) entered blocking state [ 16.617128] br-lan: port 4(lan4) entered disabled state [ 16.629585] device lan4 entered promiscuous mode [ 16.652923] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 16.666584] 8021q: adding VLAN 0 to HW filter on device wan [ 19.397756] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 19.948335] br-lan: port 1(lan1) entered blocking state [ 19.958856] br-lan: port 1(lan1) entered forwarding state [ 19.972221] br-lan: port 5(wlan0) entered blocking state [ 19.982913] br-lan: port 5(wlan0) entered disabled state [ 19.994336] device wlan0 entered promiscuous mode [ 20.005850] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 20.773839] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 20.813496] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready [ 20.826860] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 20.840271] br-lan: port 5(wlan0) entered blocking state [ 20.850992] br-lan: port 5(wlan0) entered forwarding state [ 22.155951] br-lan: port 6(wlan1) entered blocking state [ 22.166655] br-lan: port 6(wlan1) entered disabled state [ 22.178062] device wlan1 entered promiscuous mode [ 24.320854] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 24.333962] br-lan: port 6(wlan1) entered blocking state [ 24.344603] br-lan: port 6(wlan1) entered forwarding state


  • This router has nearly identical internals and the same specs as the D-Link DIR-867 A1, D-Link DIR-882 A1 and Motorola MR2600 v1 apart from the lack of USB ports.
  • Due to this similarity, most software/hardware mods and even firmwares for the DIR-867, DIR-882 and MR2600 can be applied to this router without issues.
  • D-Link DIR-1760 A1, D-Link DIR-1960 A1, D-Link DIR-2640 A1 and D-Link DIR-2660 A1 also are very similar to this router, but they have more RAM (256 MB) and flash (128 MB NAND).
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/05/09 10:58
  • by tmomas