D-Link DIR-853 A3

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE

=================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Dec 20 2018 - 11:06:07) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffa8000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 8ffdf830 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 42] Device not found, ID: c8d1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 .*** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Dec 20 2018 Time:11:06:07 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN LLLLW ================================================= Check image validation:hdr1_addr[bc180000]hdr2_addr[c0980000] Image1 Header Magic Number --> OK Image2 Header Magic Number --> OK Image1 Header Checksum --> OK Image2 Header Checksum --> OK Image1 Data Checksum --> .................................................OK Image2 Data Checksum --> .................................................OK Image1: OK Image2: OK ================================================= Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 6: System Enter UBoot to Update Img or Bin. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 0 3: System Boot system code via Flash. ## Booting image at bc180000 ... Image Name: MIPS OpenWrt Linux-6.6.73 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3175239 Bytes = 3 MB Load Address: 80001000 Entry Point: 80001000 ................................................. Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... [ 0.000000] Linux version 6.6.73 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Feb 3 23:09:37 2025 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is D-Link DIR-853 A3 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 12 pages/cpu s19136 r8192 d21824 u49152 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=0004482c [ 0.000000] Readback ErrCtl register=0004482c [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 247816K/262144K available (8363K kernel code, 653K rwdata, 1016K rodata, 1284K init, 229K bss, 14328K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.016063] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.088332] pid_max: default: 32768 minimum: 301 [ 0.106370] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.120790] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.145091] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.164017] rcu: Hierarchical SRCU implementation. [ 0.173436] rcu: Max phase no-delay instances is 1000. [ 0.184621] smp: Bringing up secondary CPUs ... [ 0.194529] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.194559] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.194574] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.194623] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.254094] Synchronize counters for CPU 1: done. [ 0.316394] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.316418] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.316431] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.316461] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.375368] Synchronize counters for CPU 2: done. [ 0.435818] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.435843] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.435856] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.435889] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.494961] Synchronize counters for CPU 3: done. [ 0.554564] smp: Brought up 1 node, 4 CPUs [ 0.569800] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.589303] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.606886] pinctrl core: initialized pinctrl subsystem [ 0.620431] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.632945] thermal_sys: Registered thermal governor 'step_wise' [ 0.634665] /pinctrl: Fixed dependency cycle(s) with /pinctrl/pinctrl0 [ 0.675090] clocksource: Switched to clocksource GIC [ 0.694874] NET: Registered PF_INET protocol family [ 0.704736] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.720760] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.737297] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.752660] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.767881] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.782172] TCP: Hash tables configured (established 2048 bind 2048) [ 0.795759] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.810359] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.823252] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.838072] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.849300] PCI: CLS 0 bytes, default 32 [ 0.860661] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.874564] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.886057] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.911505] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.929783] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.941297] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.952778] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.964398] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 0.977671] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 0.995141] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000 [ 1.011357] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.385085] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) [ 1.398870] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.412671] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.422530] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.436667] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.449233] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.460072] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.473720] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.486058] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.497931] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.510369] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.522920] pci 0000:00:00.0: supports D1 [ 1.530765] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.544199] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.560359] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 1.572288] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 1.585866] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.615674] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.626010] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.638054] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.651533] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.665881] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.679052] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.692149] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.705974] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.719444] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 1.733786] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 1.747283] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff] [ 1.759373] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 1.773889] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.783724] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.795821] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.809309] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.823642] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc [ 1.841612] pci_bus 0000:00: resource 4 [mem 0x60000000-0x6fffffff] [ 1.854051] pci_bus 0000:00: resource 5 [io 0x0000-0xffff] [ 1.865127] pci_bus 0000:01: resource 0 [io 0x0000-0x0fff] [ 1.876171] pci_bus 0000:01: resource 1 [mem 0x60000000-0x600fffff] [ 1.888611] pci_bus 0000:01: resource 2 [mem 0x60100000-0x601fffff pref] [ 1.903542] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 1.926365] printk: console [ttyS0] disabled [ 1.935767] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A [ 1.953763] printk: console [ttyS0] enabled [ 1.953763] printk: console [ttyS0] enabled [ 1.970300] printk: bootconsole [early0] disabled [ 1.970300] printk: bootconsole [early0] disabled [ 1.993623] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1 [ 2.006357] nand: ESMT NAND 128MiB 3,3V 8-bit [ 2.015054] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.030145] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 2.043262] 9 fixed-partitions partitions found on MTD device mt7621-nand [ 2.057133] Creating 9 MTD partitions on "mt7621-nand": [ 2.067586] 0x000000000000-0x000000080000 : "u-boot" [ 2.084621] 0x000000080000-0x000000100000 : "config" [ 2.101188] 0x000000100000-0x000000140000 : "factory" [ 2.115765] 0x000000140000-0x000000180000 : "config2" [ 2.129864] 0x000000180000-0x000002980000 : "firmware" [ 2.577807] 2 uimage-fw partitions found on MTD device firmware [ 2.589732] Creating 2 MTD partitions on "firmware": [ 2.599634] 0x000000000000-0x000000400000 : "kernel" [ 2.654018] 0x000000400000-0x000002800000 : "ubi" [ 3.053159] 0x000002980000-0x000004980000 : "private" [ 3.410059] 0x000004980000-0x000007180000 : "firmware2" [ 3.853359] 0x000007180000-0x000007780000 : "mydlink" [ 3.929480] 0x000007780000-0x000008000000 : "reserved" [ 4.178907] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.199807] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19 [ 4.219593] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 19 [ 4.237927] i2c_dev: i2c /dev entries driver [ 4.250663] NET: Registered PF_INET6 protocol family [ 4.263882] Segment Routing with IPv6 [ 4.271341] In-situ OAM (IOAM) with IPv6 [ 4.279337] NET: Registered PF_PACKET protocol family [ 4.289509] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.315847] 8021q: 802.1Q VLAN Support v1.8 [ 4.354930] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.395739] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode [ 4.410793] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21) [ 4.433746] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.435981] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22) [ 4.472386] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=23) [ 4.495684] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=24) [ 4.518686] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode [ 4.532231] DSA: tree 0 setup [ 4.540680] UBI: auto-attach mtd6 [ 4.547375] ubi0: attaching mtd6 [ 5.203727] ubi0: scanning is finished [ 5.223790] ubi0: attached mtd6 (name "ubi", size 36 MiB) [ 5.234650] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.248358] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.261909] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.275803] ubi0: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0 [ 5.287798] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 5.302202] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1738624177 [ 5.320411] ubi0: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20 [ 5.338832] ubi0: background thread "ubi_bgt0d" started, PID 468 [ 5.341373] block ubiblock0_0: created from ubi0:0(rootfs) [ 5.361886] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 5.376055] clk: Disabling unused clocks [ 5.391267] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.409512] Freeing unused kernel image (initmem) memory: 1284K [ 5.421408] This architecture does not have kernel memory protection. [ 5.434260] Run /sbin/init as init process [ 5.888402] init: Console is alive [ 5.895677] init: - watchdog - [ 6.723879] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.789246] usbcore: registered new interface driver usbfs [ 6.800419] usbcore: registered new interface driver hub [ 6.811288] usbcore: registered new device driver usb [ 6.823008] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 6.847643] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 6.862788] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 6.878354] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.889024] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 6.909016] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000280010 [ 6.927320] xhci-mtk 1e1c0000.xhci: irq 28, io mem 0x1e1c0000 [ 6.939051] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.949663] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 6.964583] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 6.978548] hub 1-0:1.0: USB hub found [ 6.986289] hub 1-0:1.0: 2 ports detected [ 6.995545] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 7.012856] hub 2-0:1.0: USB hub found [ 7.020542] hub 2-0:1.0: 1 port detected [ 7.038545] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 7.056576] init: - preinit - [ 7.751815] mtk_soc_eth 1e100000.ethernet wan: renamed from eth1 [ 9.185106] random: crng init done [ 9.649398] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 9.669851] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 9.684032] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 14.015336] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 14.026984] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 635 [ 14.084861] UBIFS (ubi0:1): recovery needed [ 14.215883] UBIFS (ubi0:1): recovery completed [ 14.224921] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 14.240538] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 14.260295] UBIFS (ubi0:1): FS size: 27553792 bytes (26 MiB, 217 LEBs), max 227 LEBs, journal size 1396736 bytes (1 MiB, 11 LEBs) [ 14.283522] UBIFS (ubi0:1): reserved for root: 1301433 bytes (1270 KiB) [ 14.296716] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID EEE374DD-DF1E-48B5-BCB0-FCDBC0216759, small LPT model [ 14.325123] mount_root: switching to ubifs overlay [ 14.351639] urandom-seed: Seeding with /etc/urandom.seed [ 14.465767] procd: - early - [ 14.471729] procd: - watchdog - [ 15.095627] procd: - watchdog - [ 15.103013] procd: - ubus - [ 15.269766] procd: - init - Please press Enter to activate this console. [ 16.016779] kmodloader: loading kernel modules from /etc/modules.d/* [ 16.088097] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized. [ 16.474697] jitterentropy: Initialization failed with host not compliant with requirements: 9 [ 16.658461] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a [ 16.673525] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2 [ 16.885292] pci 0000:00:00.0: enabling device (0000 -> 0003) [ 16.896636] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 16.919582] mt7615e 0000:01:00.0: registering led 'mt76-phy0' [ 17.048468] mt7615e 0000:01:00.0: registering led 'mt76-phy1' [ 17.076597] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 17.076597] [ 17.179807] urngd: v1.0.2 started. [ 17.331261] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 17.358805] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149 [ 17.399336] PPP generic driver version 2.4.2 [ 17.409992] NET: Registered PF_PPPOX protocol family [ 17.430420] mtdblock: MTD device 'factory' is NAND, please consider using UBI block devices instead. [ 17.849837] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.486089] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 26.519143] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 26.535357] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 26.542493] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 26.568663] br-lan: port 1(lan1) entered blocking state [ 26.579304] br-lan: port 1(lan1) entered disabled state [ 26.590039] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode [ 26.602708] mtk_soc_eth 1e100000.ethernet eth0: entered allmulticast mode [ 26.619865] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode [ 26.656556] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode [ 26.672651] br-lan: port 2(lan2) entered blocking state [ 26.683378] br-lan: port 2(lan2) entered disabled state [ 26.694051] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode [ 26.708493] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode [ 26.734825] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode [ 26.751535] br-lan: port 3(lan3) entered blocking state [ 26.762126] br-lan: port 3(lan3) entered disabled state [ 26.772753] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode [ 26.788069] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode [ 26.813720] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode [ 26.829542] br-lan: port 4(lan4) entered blocking state [ 26.840177] br-lan: port 4(lan4) entered disabled state [ 26.850855] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode [ 26.866386] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode [ 26.897705] mtk_soc_eth 1e100000.ethernet wan: PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=POLL) [ 26.916733] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode [ 30.325371] mt7530-mdio mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 35.641279] br-lan: port 2(lan2) entered blocking state [ 35.651789] br-lan: port 2(lan2) entered forwarding state [ 35.664007] br-lan: port 5(phy0-ap0) entered blocking state [ 35.675201] br-lan: port 5(phy0-ap0) entered disabled state [ 35.686433] mt7615e 0000:01:00.0 phy0-ap0: entered allmulticast mode [ 35.699535] mt7615e 0000:01:00.0 phy0-ap0: entered promiscuous mode [ 35.745610] br-lan: port 5(phy0-ap0) entered blocking state [ 35.756783] br-lan: port 5(phy0-ap0) entered forwarding state [ 35.932002] br-lan: port 6(phy1-ap0) entered blocking state [ 35.943354] br-lan: port 6(phy1-ap0) entered disabled state [ 35.954761] mt7615e 0000:01:00.0 phy1-ap0: entered allmulticast mode [ 35.968245] mt7615e 0000:01:00.0 phy1-ap0: entered promiscuous mode [ 35.981566] br-lan: port 6(phy1-ap0) entered blocking state [ 35.992804] br-lan: port 6(phy1-ap0) entered forwarding state