Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:d-link:dir-853_a1 [2024/02/13 04:54] – [Specific Configuration] rikka0w0toh:d-link:dir-853_a1 [2024/02/13 05:05] – [Hardware mods] rikka0w0
Line 138: Line 138:
 ->  [[docs:guide-user:installation:generic.sysupgrade]] ->  [[docs:guide-user:installation:generic.sysupgrade]]
  
-<WRAP BOX> +Both LuCI web upgrade and terminal upgrade works.
- +
-FIXME These are generic instructions. Update with your router's specifics. +
- +
-==== LuCI Web Upgrade Process ==== +
- +
-  * Browse to ''<nowiki>http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/</nowiki>'' LuCI Upgrade URL +
-  * Upload image file for sysupgrade to LuCI +
-  * Wait for reboot +
- +
-==== Terminal Upgrade Process ==== +
- +
-If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. +
-There are two command line methods for upgrading: +
- +
-  * ''sysupgrade'' +
-  * ''mtd'' +
- +
-Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. +
- +
-=== sysupgrade === +
- +
-  * Login as root via SSH on 192.168.1.1, then enter the following commands: +
- +
-<code> +
-cd /tmp +
-wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc +
-sysupgrade /tmp/xxx.abc +
-</code> +
- +
-=== mtd === +
- +
-If ''sysupgrade'' does not support this router, use ''mtd''+
- +
-  * Login as root via SSH on 192.168.1.1, then enter the following commands: +
- +
-<code> +
-cd /tmp +
-wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc +
-mtd write /tmp/xxx.abc linux && reboot +
-</code> +
- +
-</WRAP> +
  
 ===== Failsafe mode ===== ===== Failsafe mode =====
Line 187: Line 144:
  
  
-===== Specific Configuration ===== 
- 
-<WRAP BOX> 
-FIXME Please fill in real values for this device, then remove the EXAMPLEs 
  
 +===== Hardware =====
 ==== MAC addresses on OEM firmware ==== ==== MAC addresses on OEM firmware ====
-The default network configuration is: 
 ^ Interface Name   ^ Location on the flash ^ Note    ^ ^ Interface Name   ^ Location on the flash ^ Note    ^
 | lan (eth2)       | @factory + 0xe000     | on label   | | lan (eth2)       | @factory + 0xe000     | on label   |
Line 200: Line 153:
 | 5g (ra0)         | not on flash          | lan + 2    | | 5g (ra0)         | not on flash          | lan + 2    |
  
-</WRAP>+==== Info ====
  
-==== Switch Ports (for VLANs) ==== +  * LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue 
-<WRAP BOX> +  * Buttons: Reset,WPSWifi
-FIXME Please fill in real values for this devicethen remove the EXAMPLEs+
  
-Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. 
-^ Port             ^ Switch port   ^ 
-| Internet (WAN)   | EXAMPLE 4     | 
-| LAN 1            | EXAMPLE 3     | 
-| LAN 2            | EXAMPLE 2     | 
-| LAN 3            | EXAMPLE 1     | 
-| LAN 4            | EXAMPLE 0     | 
- 
-</WRAP> 
- 
-==== Buttons ==== 
--> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s). 
-Here, we merely name the buttons, so we can use them in the above Howto. 
- 
-<WRAP BOX> 
-FIXME Please fill in real values for this device, then remove the EXAMPLEs 
- 
-The D-Link DIR-853 has the following buttons: 
- 
-^ BUTTON                       ^ Event   ^ 
-| EXAMPLE Reset                |  reset  | 
-| EXAMPLE Secure Easy Setup    |   ses   | 
-| EXAMPLE No buttons at all.      -    | 
- 
-</WRAP> 
- 
-===== Hardware ===== 
-==== Info ==== 
 <WRAP BOX> <WRAP BOX>
 FIXME FIXME
Line 276: Line 200:
 ===== Hardware mods ===== ===== Hardware mods =====
  
-None so far.+**Not verified!** 
 + 
 +There is an unpopulated USB 2.0 port on the PCB. To use it, you need to short circuit R31, LB15, R35, R38, and R37 on the PCB: 
 + 
 +{{media:dlink:dir-853_a1:usb_mod.jpg}} 
 + 
 +The pin out of the USB socket (from the top to bottom) is: 
 +  - Vcc, 5V 
 +  - D- 
 +  - D+ 
 +  - GND 
 + 
 +This port should work on the official OpenWrt firmware, as ''mt7621.dtsi'' suggests that it is enabled by default.
  
  
  • Last modified: 2024/02/13 05:08
  • by rikka0w0