D-Link DIR-810L

The DIR-810L Wireless AC750 Dual-Band Router is based on the MT7620A SoC. It has two wireless radios, a 802.11bgn one (SoC-integrated) and a 802.11ac one (on-board).

D-Link DIR-810L (front view)

OEM source code available at: http://tsd.dlink.com.tw/downloads2008list.asp?t=1&OS=GPL&pagetype=S

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
DIR-810LA1, B1MediaTek MT7620A580864MediaTek MT7620A, MediaTek MT7610Eb/g/na/n/ac5---

Later versions of this router (bought mine in 02/16) with Rev. B1 and F/W 2.03b02 don't have an open bootloader and there is also no factory image for this router.

In order to build one, the correct signature needs to be appended to the end of the sysupgrade file with a tool found in the GPL toolchain download from D-Link.

These are the necessary steps:

  1. Download SDK from http://tsd.dlink.com.tw/GPL.asp that corresponds to your hardware version. The firmware version shouldn't matter as the tool should be the same for all versions
  2. extract the tarball in the source subdirectory
  3. find the tool ncc_att_hwid (should be in source/user/wolf/cameo/ncc/hostTools)
  4. Download the sysupgrade image for the DIR-810L
  5. modify it like so: ./ncc_att_hwid -f /tmp/openwrt-15.05-ramips-mt7620-dir-810l-squashfs-sysupgrade.bin -m DIR-810L -H B1 -r WW -c 1.0 -F 2.03b02 -a

Recovery mode wouldn't accept it but the normal factory web interface does.

D-Link DIR-810L (rear view) D-Link DIR-810L B1 (PCB rear view)

The D-Link DIR-810L features a TTL serial port. You can use a TTL to USB adaptor to connect to it. The following image shows the pin location. There's no need to connect Vcc.

D-Link DIR-810L serial TTL pinout

Settings: 57600 8N1

U-Boot 1.1.3 (Jan  7 2013 - 16:08:08)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83f98000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29 
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D

MAC: c8:d3:a3:64:ce:0a
============================================ 
Ralink UBoot Version: 4.1.1.0
DIR-810L(1.00b03)
-------------------------------------------- 
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  7 2013  Time:16:08:08
============================================ 
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 580 MHZ #### 
 estimate memory size =64 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bc170000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5976005 Bytes =  5.7 MB
   Load Address: 80000000
   Entry Point:  8000c2d0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

No initrd
## Transferring control to Linux (at address 8000c2d0) ...
## Giving linux memsize in MB, 64

/proc/mtd

# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00800000 00010000 "ALL"
mtd1: 00030000 00010000 "Bootloader"
mtd2: 00010000 00010000 "Config"
mtd3: 00010000 00010000 "Factory"
mtd4: 00010000 00010000 "5G_RF"
mtd5: 00010000 00010000 "Wolf_Config"
mtd6: 00080000 00010000 "MyDLink"
mtd7: 00080000 00010000 "Jffs2"
mtd8: 000f8f8d 00010000 "Kernel"
mtd9: 00597073 00010000 "RootFS"
mtd10: 00690000 00010000 "Kernel_RootFS"

Starting kernel ... LINUX started... THIS IS ASIC init started: BusyBox v1.12.1 (2013-03-28 15:33:49 CST) starting pid 35, tty '': '/etc_ro/rcS' mount: mounting none on /proc/bus/usb failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= mount mydlink ok mount flash ok old language pack not found language pack exists Starting loop GPIO LED=9,PBC=2 Waiting for Wireless Events from interfaces... [ leobox_ipc.c: 207 sem_create()]:::add semid = 0 [ leobox_ipc.c: 207 sem_create()]:::add semid = 32769 [ leobox_ipc.c: 207 sem_create()]:::add semid = 65538 [ leobox_ipc.c: 207 sem_create()]:::add semid = 98307 [ leobox_ipc.c: 207 sem_create()]:::add semid = 131076 [ leobox_ipc.c: 207 sem_create()]:::add semid = 163845 [ leobox_ipc.c: 207 sem_create()]:::add semid = 196614 [ leobox_ipc.c: 207 sem_create()]:::add semid = 229383 [ leobox_ipc.c: 207 sem_create()]:::add semid = 262152 [ leobox_ipc.c: 207 sem_create()]:::add semid = 294921 [ leobox_ipc.c: 207 sem_create()]:::add semid = 327690 [ leobox_ipc.c: 207 sem_create()]:::add semid = 360459 [ leobox_ipc.c: 207 sem_create()]:::add semid = 393228 [ leobox_ipc.c: 207 sem_create()]:::add semid = 425997 [ leobox_ipc.c: 207 sem_create()]:::add semid = 458766 [ leobox_ipc.c: 207 sem_create()]:::add semid = 491535 [ leobox_ipc.c: 207 sem_create()]:::add semid = 524304 [ leobox_ipc.c: 207 sem_create()]:::add semid = 557073 [ leobox_ipc.c: 207 sem_create()]:::add semid = 589842 [ leobox_ipc.c: 207 sem_create()]:::add semid = 622611 [ leobox_ipc.c: 207 sem_create()]:::add semid = 655380 [ 122 ncc_main.c : 177 main()]:::[122]Thread Create[main thread] [ 122 ncc_runtimecfg.c : 432 initRunTimeCfg()]:::Init Run-Time Config Success. [ 122 ncc_runtimecfg.c : 433 initRunTimeCfg()]:::Total 4342 nodes, each node 24 bytes. [ 122 ncc_runtimecfg.c : 434 initRunTimeCfg()]:::Total 104208 byte for all nodes. [ 122 ncc_runtimecfg.c : 435 initRunTimeCfg()]:::Total 63953 byte for data. [ 122 ncc_runtimecfg.c : 153 loadCfg()]:::Start loadCfg [ 122 ncc_lz77.c : 534 flash2rootfs()]:::Load Success(/var/tmp/cfg.txt) ================nice=-20 starting pid 145, tty '/dev/ttyS1': '/bin/sh' # [ 122 ncc_lz77.c : 628 rootfs2flash()]:::write header KBLA,32548 [ 122 ncc_lz77.c : 633 rootfs2flash()]:::write data 32548 [ 122 ncc_lz77.c : 646 rootfs2flash()]:::write sync done [ 122 ncc_inf.c : 605 ncc_inf_main()]:::JTraceLevel=4 [ 122 leobox_network.c : 1064 socket_select()]:::Enter pid=122,ppid=1 [leobox_network.c: 1074 socket_select()]:::main process get thread id=1026 [ 149 ncc_inf.c : 432 processInf()]:::[149]Thread Create[processInf] [ 148 leobox_network.c : 816 socket_select_hdlr()]:::[148]Thread Create[socket_select_hdlr] bind: Address already in use [ 122 ncc_main.c : 269 main()]:::Stop Web Access HTTP [ 122 ncc_httpd.c : 539 httpdOp()]:::st is null. [ 122 /opt/release/RT288x_SDK_0214/RT288x_SDK/source/user/wolf/cameo/ncc/../model/dlink_810/objTools/ncc_objTools.c: 5036 probeHTTPsEnable()]:::probeHTTPsEnable(); [ 122 ncc_main.c : 291 main()]:::Start HTTPS mini_httpd: started as root without requesting chroot(), warning only sh: cannot create /sys/class/net/br0/bridge/tcp_allow: nonexistent directory bind: Address already in use [ 122 ncc_main.c : 305 main()]:::Stop Web Access HTTPS [ 122 ncc_httpd.c : 539 httpdOp()]:::st is null. mini_httpd: started as root without requesting chroot(), warning only [ 162 ncc_main.c : 41 sendBootEvent()]:::[162]Thread Create[sendBootEvent] [ 161 leobox_timer.c : 248 timerThread()]:::[161]Thread Create[timerThread] [ 161 leobox_timer.c : 256 timerThread()]:::Timer Thread Running sh: cannot create /proc/sys/net/ipv4/conf/eth2.2/arp_ignore: nonexistent directory [ 122 ncc_fsm_boot.c : 513 Boot()]:::=====================Start DIR_810_Boot===================== [ 122 ncc_fsm_boot.c : 570 Boot()]:::MAC 0 = C8D3A364CE0A [ 122 ncc_fsm_boot.c : 571 Boot()]:::MAC 1 = C8D3A364CE0B switch reg write offset=3100, value=56330 switch reg write offset=3200, value=56330 switch reg write offset=3300, value=56330 switch reg write offset=3400, value=56330 switch reg write offset=3000, value=56330 Set: phy[4].reg[4] = 05e1 Set: phy[4].reg[0] = 3300 [ 122 ncc_l2_independence.c: 171 swSpeedSet()]:::port = 4, speed = 0 killall: crond: no process killed [ 122 ncc_crond.c : 54 crondConf()]:::DEBUG ON [ 122 ncc_firewall.c : 1601 reBuildMAC6()]:::reBuildMAC6()+ [ 122 ncc_firewall.c : 1629 reBuildMAC6()]:::reBuildMAC6()- ip6tables: No chain/target/match by that name. killall: wakeOnLanProxy: no process killed [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== ### WOL CONFIG: No such file or directory [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== [ 122 ncc_fsm_boot.c : 780 Boot()]:::cfg->tzone=128 Sat Jan 1 00:00:00 GMT 2011 [ 122 ncc_fsm_boot.c : 806 Boot()]:::Merge language pack!! [ 4242 lang_merge.c : 1125 main()]:::before print info [ 4242 lang_merge.c : 1128 main()]:::Parameters: ori_lang_fp: /var/tmp/lang.js def_lang_fp: /www/def_lang.js [ 4242 lang_merge.c : 1196 main()]:::save to old js file!! [ 4242 lang_merge.c : 1197 main()]:::save to old js file!! [ 4242 lang_merge.c : 1198 main()]:::save to old js file!! sh: cannot create /proc/sys/net/ipv6/conf/ra1/disable_ipv6: nonexistent directory sh: cannot create /proc/sys/net/ipv6/conf/rai1/disable_ipv6: nonexistent directory [ 122 ncc_help.c : 1268 checkDefCfg()]:::defCfg=1 llmnr: have no available linklocal address. wait count=0 [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=1 [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== llmnr: have no available linklocal address. wait count=2 mDNSResponderPosix: Starting in daemon mode killall: lld2d: no process killed ***** g_wl_interface = ra0 ****** killall: proxy: no process killed [ leobox_ipc.c: 207 sem_create()]:::add semid = 688149 [ 6008 lanmapd.c : 2646 main()]:::=============================Lanmapd============================= [ 6008 lanmapd.c : 2647 main()]:::iface br0 [ 6008 lanmapd.c : 2648 main()]:::ip 192.168.0.1 [ 6008 lanmapd.c : 2652 main()]:::netmask 255.255.255.0 [ 6008 lanmapd.c : 2653 main()]:::network id 192.168.0.0 [ 6008 lanmapd.c : 2654 main()]:::mac c8:d3:a3:64:ce:0a [ 6008 lanmapd.c : 2655 main()]:::hostname dlinkrouter [ 6008 lanmapd.c : 2656 main()]:::hostname encode EEEMEJEOELFCEPFFFEEFFCCACACACAAA [ 6008 lanmapd.c : 2661 main()]:::================================================================= killall: crond: no process killed llmnr: have no available linklocal address. wait count=3 killall: wscd: no process killed Starting loop GPIO LED=9,PBC=2 [ 122 ncc_fsm_boot.c : 307 doRtInit()]:::Send Event to open 2.4G Wlan ! [ 122 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=4 llmnr: have no available linklocal address. wait count=5 llmnr: have no available linklocal address. wait count=6 llmnr: have no available linklocal address. wait count=7 llmnr: have no available linklocal address. wait count=8 llmnr: have no available linklocal address. wait count=9 [ 122 ncc_fsm_boot.c : 312 doRtInit()]:::Send Event to open 5G Wlan ! [ 122 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=10 llmnr: have no available linklocal address. wait count=11 llmnr: have no available linklocal address. wait count=12 Starting loop GPIO LED=9,PBC=2 killall: wscd: no process killed libupnp: using UDP SSDP_PORT = 1900 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy Interface doesn't accept private ioctl... set (8BE2): Invalid argument Interface doesn't accept private ioctl... set (8BE2): Invalid argument Starting loop GPIO LED=9,PBC=2 route: ioctl 0x890b failed: File exists [ 122 ncc_fsm_boot.c : 920 Boot()]:::wanCableLink = 0 mDNSResponderPosix: Starting in daemon mode [ 122 ncc_dev_independence.c: 3757 devOpFunc()]:::get internet_cable_lose [ 122 ncc_firewall.c : 4672 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=13 [ 122 ncc_firewall.c : 4674 runFwScript()]:::===ipt run end=== ip6tables: Bad rule (does a matching rule exist in that chain?). llmnr: have no available linklocal address. wait count=14 [ 122 ncc_help.c : 1621 is_v6defaultgw_exist()]:::[IPv6 WARNING] Default GW not Exist. [ 122 ncc_radvd.c : 233 radvdConf()]:::is6rdsunset: 0, prefix: [ 122 ncc_fsm_boot.c : 1296 Boot()]:::setting v6Lan Host Filter=fe80:0:0:0:cad3:a3ff:fe64:ce0b! [ 122 ncc_fsm_boot.c : 1318 Boot()]:::=====================finish DIR_810_Boot===================== [SYS][ 122 ncc_fsm_boot.c : 1333 Boot()]:::Boot Complate!! [ 122 ncc_EventInternal.c : 1128 doEventInternal()]:::InternalLocalTimeChange [ 122 ncc_EventInternal.c : 498 onMailSchedule()]:::mailCfg.schedSendEnable ? 0 [ 122 ncc_EventInternal.c : 1147 doEventInternal()]:::needSendLog = 0 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy


Starting kernel ... [ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41795) ) #3 Mon Jul 28 18:38:34 CEST 2014 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is D-Link DIR-810L [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00066eb0 [ 0.000000] Readback ErrCtl register=00066eb0 [ 0.000000] Memory: 61376k/65536k available (2519k kernel code, 4160k reserved, 609k data, 196k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.460000] bio: create slab <bio-0> at 0 [ 0.470000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.480000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.490000] PCI host bridge to bus 0000:00 [ 0.500000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.510000] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff] [ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.530000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.540000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.560000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.570000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.570000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.580000] Switching to clocksource MIPS [ 0.590000] NET: Registered protocol family 2 [ 0.590000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.600000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.610000] TCP: Hash tables configured (established 512 bind 512) [ 0.630000] TCP: reno registered [ 0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.660000] NET: Registered protocol family 1 [ 0.670000] rt-timer 10000100.timer: maximum frequncy is 2441Hz [ 0.700000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.710000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.730000] msgmni has been set to 119 [ 0.740000] io scheduler noop registered [ 0.740000] io scheduler deadline registered (default) [ 0.750000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.770000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.790000] console [ttyS0] enabled, bootconsole disabled [ 0.790000] console [ttyS0] enabled, bootconsole disabled [ 0.820000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes) [ 0.830000] 8 ofpart partitions found on MTD device spi32766.0 [ 0.840000] Creating 8 MTD partitions on "spi32766.0": [ 0.850000] 0x000000000000-0x000000030000 : "u-boot" [ 0.860000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.870000] 0x000000040000-0x000000050000 : "factory" [ 0.880000] 0x000000050000-0x000000060000 : "factory5g" [ 0.900000] 0x000000060000-0x000000070000 : "Wolf_Config" [ 0.910000] 0x000000070000-0x0000000f0000 : "MyDlink" [ 0.920000] 0x0000000e0000-0x000000160000 : "Jffs2" [ 0.930000] 0x000000170000-0x000000800000 : "firmware" [ 0.940000] 0x00000028003e-0x000000800000 : "rootfs" [ 0.950000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.980000] mtd: device 8 (rootfs) set to be root filesystem [ 0.990000] mtd: partition "rootfs_data" created automatically, ofs=0x4a0000, len=0x360000 [ 1.010000] 0x0000004a0000-0x000000800000 : "rootfs_data" [ 1.020000] gsw: setting port4 to ephy mode [ 1.030000] (unregistered net_device): port 0 link up (100Mbps/Full duplex) [ 1.050000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver [ 1.060000] eth0: done loading [ 1.070000] rt3xxx-usbphy ubsphy.3: loaded [ 1.080000] rt2880_wdt 10000120.watchdog: Initialized [ 1.090000] TCP: cubic registered [ 1.090000] NET: Registered protocol family 17 [ 1.100000] Bridge firewalling registered [ 1.110000] 8021q: 802.1Q VLAN Support v1.8 [ 1.130000] VFS: Mounted root (squashfs filesystem) readonly on device 31:8. [ 1.150000] Freeing unused kernel memory: 196K (8030f000 - 80340000) procd: Console is alive procd: - watchdog - [ 4.570000] usbcore: registered new interface driver usbfs [ 4.580000] usbcore: registered new interface driver hub [ 4.590000] usbcore: registered new device driver usb [ 4.610000] leds-gpio gpio-leds.5: pins are not configured from the driver procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready jffs2 is ready [ 7.290000] jffs2: notice: (313) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 8.630000] NET: Registered protocol family 10 [ 8.650000] nf_conntrack version 0.5.0 (962 buckets, 3848 max) [ 8.670000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.690000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 8.700000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 8.720000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.770000] xt_time: kernel timezone is -0000 [ 8.800000] cfg80211: Calling CRDA to update world regulatory domain [ 8.810000] cfg80211: World regulatory domain updated: [ 8.820000] cfg80211: DFS Master region: unset [ 8.830000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 8.850000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 8.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 8.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 8.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 8.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 8.930000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 8.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 8.960000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 9.040000] PPP generic driver version 2.4.2 [ 9.060000] NET: Registered protocol family 24 [ 9.100000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 9.110000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. procd: Could not[ 9.160000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM. find firmware /[ 9.180000] rt2800_wmac: probe of 10180000.wmac failed with error -2 lib/firmware/soc_wmac.eeprom procd: - init complete - [ 15.600000] device eth0.1 entered promiscuous mode [ 15.610000] device eth0 entered promiscuous mode [ 15.620000] br-lan: port 1(eth0.1) entered forwarding state [ 15.630000] br-lan: port 1(eth0.1) entered forwarding state [ 17.630000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.22.1 (2014-07-22 12:47:56 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (14.07-rc2, r41815) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2020/06/02 20:14
  • by tmomas