D-Link DIR-3060 A1

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The D-Link DIR-3060 (Gaming AC3000) was a high-end home router / wireless access point. It was marketed to families and “gamers” using a sci-fi design and partnerships with Norton AntiVirus, Ookla Speedtest, Amazon Alexa, and Google Assistant. Apparently unsuccessful, it was quickly discontinued, receiving no further hardware revisions.

Layer0 raw flash, 128MiB
Layer1 mtd0
“Bootloader”
512KiB
mtd1
“config”
512KiB
mtd2
“factory”
256KiB
mtd3
“config2”
256KiB
mtd4
“firmware”
40MiB
mtd7
“private”
32MiB
mtd8
“firmware2”
40MiB
mtd9
“mydlink”
6MiB
mtd10
“reserved”
8.5MiB
Layer2 mtd5
“kernel”
4MiB
mtd6
“ubi”
36MiB

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
lan1(,2,3,4) LAN ports (1 to 4) None
eth0 WAN port DHCP
wan WiFi Disabled
phy0(,1,2)-ap0 Separate WiFi access points Disabled

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The D-Link DIR-3060 has the following buttons:

BUTTON Event
Reset reset
Wi-Fi Protected Setup wps

Front:

Back:

Backside label:

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
dir-3070_a1_serial.jpg

Serial connection parameters
for D-Link DIR-3060 A1
EXAMPLE 57600, 8N1, ?V

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xa, 1/0 = 595/429 29000000 PLL2 FB_DL: 0xd, 1/0 = 585/439 35000000 PLL4 FB_DL: 0xf, 1/0 = 582/442 3D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001F1F ================================================================== RX DQS perbit delay software ca =================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xa, 1/0 = 622/402 29000000 PLL2 FB_DL: 0xd, 1/0 = 578/446 35000000 PLL4 FB_DL: 0xf, 1/0 = 561/463 3D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 opt_dle value:10 DRAMC_R0DELDLY[018]=00001E1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 8 9 11 9 9 10 7 7 7 10 | 9 9 10 11 9 11 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~60)30 8 (2~59)30 1 (1~61)31 9 (1~58)29 2 (1~60)30 10 (1~60)30 3 (1~62)31 11 (1~59)30 4 (1~60)30 12 (1~60)30 5 (1~61)31 13 (1~58)29 6 (2~60)31 14 (1~60)30 7 (1~58)29 15 (1~59)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 8 10 11 10 9 10 9 7 8 10 | 9 9 10 12 9 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff2000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff0080 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Apr 25 2019 - 14:47:34) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffa8000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 8ffdfe30 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 42] Device found in MTK table, ID: c8d1, EXT_ID: 809542 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: 4 MBytes NOR Flash Date:Apr 25 2019 Time:14:47:34 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN LLLLW ########BUTTON_RESET: 15 ================================================= Check image validation:hdr1_addr[bc180000]hdr2_addr[c0980000] Image1 Header Magic Number --> OK Image2 Header Magic Number --> OK Image1 Header Checksum --> OK Image2 Header Checksum --> OK Image1 Data Checksum --> ....................................................................................................................................................................................................................................................................................OK ..Erasing NAND Flash... ranand_erase: start:80000, len:20000 .Writing to NAND Flash... done Image2 Data Checksum --> ....................................................................................................................................................................................................................................................................................OK Image1 Stable Flag --> Stable Image1 Try Counter --> 0 Image1: OK Image2: OK ================================================= Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 6: System Enter UBoot to Update Img or Bin. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 You choosed 3  0 3: System Boot system code via Flash. ## Booting image at bc180000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 18059453 Bytes = 17.2 MB Load Address: 81001000 Entry Point: 81637600 .................................................................................................................................................................................................................................................................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 81637600) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 3.10.14+ (wubangrun@wireless) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #13 SMP Tue May 12 17:23:17 CST 2020 The CPU feqenuce set to 880 MHz MIPS CPU sleep mode enabled. GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 10000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone ranges: DMA [mem 0x00000000-0x00ffffff] Normal [mem 0x01000000-0x0fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x0fffffff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 7 pages/cpu @82937000 s6592 r8192 d13888 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Writing ErrCtl register=000412f6 Readback ErrCtl register=000412f6 Memory: 236004k/262144k available (6402k kernel code, 26140k reserved, 2047k data, 14520k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 574.46 BogoMIPS (lpj=1148928) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_PCI_PCICFG_ADDR= 21007f2 RALINK_PCI_PCICFG_ADDR = 21007f0 RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f0 -> 21007f0 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 Load Kernel WDG Timer Module jffs2: version 2.2. (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. fuse init (API version 7.22) msgmni has been set to 460 io scheduler noop registered (default) reg_int_mask=0, INT_MASK= 0 HSDMA_init hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 TX_CTX_IDX0 = 0 TX_DTX_IDX0 = 0 RX_CRX_IDX0 = 3ff RX_DRX_IDX0 = 0 set_fe_HSDMA_glo_cfg HSDMA_GLO_CFG = 465 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A Ralink gpio driver initialized:power_gpio[8] brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 82682e30 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 42, 00809542] Device not found, ID: c8d1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c8d1 NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 10 MTD partitions on "MT7621-NAND": 0x000000000000-0x000007f80000 : "ALL" 0x000000000000-0x000000080000 : "Bootloader" 0x000000080000-0x000000100000 : "Config" 0x000000100000-0x000000140000 : "Factory" 0x000000140000-0x000000180000 : "Config2" 0x000000180000-0x000002980000 : "Kernel" 0x000002980000-0x000004980000 : "Private" 0x000004980000-0x000007180000 : "Kernel2" 0x000007180000-0x000007780000 : "mydlink" 0x000007780000-0x000008080000 : "Reserved" mtd: partition "Reserved" extends beyond the end of device "MT7621-NAND" -- size truncated to 0x800000 [mtk_nand] probe successfully! IMQ driver loaded successfully. (numdevs = 2, numqueues = 1) Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register mt_drv === pAd = c2201000, size = 3735104 === <-- RTMPAllocAdapterBlock, Status=0 pAd->PciHif.CSRBaseAddress =0xc2100000, csr_addr=0xc2100000! RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 1st ePAeLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_2G_EEPROM.bin Use 1st ePAeLNA default bin. Use 1st ePAeLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_2G_EEPROM.bin Use 1st ePAeLNA default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8da00208,8da00208 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8da00218,8da00218 <-- RTMPAllocTxRxRingMemory, Status=0 [MTWF][dlink_mesh_check_data_struct]: check data structure: PASS [MTWF][mesh_module_init]: init hook functions. === pAd = c2701000, size = 3735104 === <-- RTMPAllocAdapterBlock, Status=0 pAd->PciHif.CSRBaseAddress =0xc2600000, csr_addr=0xc2600000! RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 2nd ePAeLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_5G_EEPROM.bin Use 2nd ePAeLNA default bin. Use 2nd ePAeLNA default bin. Load EEPROM Buffer from /etc_ro/wlan/MT7615_5G_EEPROM.bin Use 2nd ePAeLNA default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8e00d508,8e00d508 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8e00d518,8e00d518 <-- RTMPAllocTxRxRingMemory, Status=0 rdm_major = 253 GMAC1_MAC_ADRH -- : 0x00006063 GMAC1_MAC_ADRL -- : 0x4c7c3301 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x00006063 GMAC1_MAC_ADRL -- : 0x4c7c3301 PROC INIT OK! ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver *****run project phy. FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver funsoft usbserial: USB Serial support registered for funsoft usbcore: registered new interface driver ir_usb usbserial: USB Serial support registered for IR Dongle usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) u32 classifier Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3687 buckets, 14748 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team Type=Linux arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 Warning: unable to open an initial console. Freeing unused kernel memory: 14520K (81842000 - 82670000) procd: Console is alive procd: - preinit - Algorithmics/MIPS FPU Emulator v1.5 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level procd: - early - procd: - ubus - procd: - init - Please press Enter to activate this console. ##############sysfixtime################## #########################boot###################### ##########Wait procd to be connected with ubusd########## ##########Wait procd to be connected with ubusd########## ##########Procd has be connected with ubusd########## #############start prog=/usr/bin/if_monitor################# #############complete prog=/usr/bin/if_monitor################# #############start prog=/sbin/preinit################# #############complete prog=/sbin/preinit################# main: ***preinit start*** #######################done##################### procd: - init complete - [system]: insmod /lib/modules/jnl.ko jnl: driver (UFSD_HEAD ufsd_f_114579_r322585_b29) loaded at c20b5000 [system]: insmod /lib/modules/ufsd.ko ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd: driver (UFSD_HEAD ufsd_f_114579_r322585_b29, ioctl, sd2(5), tr, rsrc, car) loaded at c2ba2000 NTFSJ support included FAT support included Hfs+J support included Build_for__DLINK_DIR-2660_k3.10.14_2018-06-04_ufsd_f_114579_r322585_b29 ufsd: PAGE_SIZE=4K, THREAD_SIZE=8k ufsd: Kernel .config hash: original 0xb32fed90, current can't check. ufsd: Kernel .config hash: original 0xb32fed90, current can't check [system]: /etc/init.d/tw_hotplug restart [system]: insmod /lib/modules/3.10.14+/kernel/drivers/usb/storagusbcore: registered new interface driver usb-storage e/usb-storage.ko crc fail 6d471630 != e607adcf old 0.5, now 0.5 [system]: /etc/init.d/nvram_daemon restart [check_Default_Config]factory_flag=2[system]: led power high on [system]: gpio l 8 4000 0 1 0 4000 [system]: mkdir -p /var/etc/samba [system]: mkdir -p /var/etc/samba/config [system]: chpasswd --md5 < /tmp/tmpchpw [system]: chmod 600 /etc/passwd [system]: chmod 600 /etc/shadow [system]: addgroup -g 500 nobody [system]: adduser -H -D -G nobody nobody [system]: addgroup -g 600 root [system]: adduser -H -D -G root root jffs2: Empty flash at 0x00042174 ends at 0x00042800 version_old=[3.0.0-b89 ], version_new=[3.0.0-b89 ] flag=0, len of config2_base64date is 2324! /mydlink/cert/client.crt.key is ok! flag=1, len of config2_base64date is 1752! /mydlink/cert/client.crt.pem is ok! [system]: mkdir -p /var/60:63:4C:7C:33: 1 McAfee [systemRaeth v3.1 (]: mkdir -p /varTasklet/McAfee/.shgw ) [system]: ln -sf /private/McAfeeset CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 /config/ /etc/Mc phy_tx_ring = 0x00cac000, tx_ring = 0xa0cac000 Afee/config [s phy_rx_ring0 = 0x00cb0000, rx_ring[0] = 0xa0cb0000 ystem]: ifconfig phy_rx_ring0 = 0x00cb0000, rx_ring[0] = 0xa0cb0000 eth2 0.0.0.0 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x00006063 GMAC1_MAC_ADRL -- : 0x4c7c3301 GDMA2_MAC_ADRH -- : 0x00006063 GDMA2_MAC_ADRL -- : 0x4c7c3305 eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 [system]: ifconfig eth3 up eth3: ===> VirtualIF_open [system]: config-vlan.sh 3 0 [system]: switch vlan set 1 1 11110011 [system]: switch vlan set 2 2 00001100 [system]: switch pvid 4 2 [system]: switch pvid 5 2 [system]: switch reg w 2004 ff0003 [system]: switch reg w 2104 ff0003 [system]: switch reg w 2204 ff0003 [system]: switch reg w 2304 ff0003 [system]: switch reg w 2404 ff0003 [system]: switch reg w 2504 ff0003 [system]: switch reg w 2604 ff0003 [system]: ifconfig lo 127.0.0.1 [system]: vconfig add eth2 1 [system]: vconfig set_ingress_map eth2.1 0 0 [system]: vconfig set_ingress_map eth2.1 1 1 [system]: vconfig set_ingress_map eth2.1 2 2 [system]: vconfig set_ingress_map eth2.1 3 3 [system]: vconfig set_ingress_map eth2.1 4 4 [system]: vconfig set_ingress_map eth2.1 5 5 [system]: vconfig set_ingress_map eth2.1 6 6 [system]: vconfig set_ingress_map eth2.1 7 7 [system]: vconfig set_egress_map eth2.1 0 0 [system]: vconfig set_egress_map eth2.1 1 1 [system]: vconfig set_egress_map eth2.1 2 2 [system]: vconfig set_egress_map eth2.1 3 3 [system]: vconfig set_egress_map eth2.1 4 4 [system]: vconfig set_egress_map eth2.1 5 5 [system]: vconfig set_egress_map eth2.1 6 6 [system]: vconfig set_egress_map eth2.1 7 7 [system]: vconfig add eth2 2 [system]: vconfig set_ingress_majffs2: notice: (366) check_node_data: wrong data CRC in data node at 0x0004f4e8: read 0xc9b018d1, calculated 0xdc632a32. p eth2.2 0 0 [system]: vconfig set_ingress_map eth2.2 1 1 [system]: vconfig set_ingress_map eth2.2 2 2 [system]: vconfig set_ingress_map eth2.2 3 3 [system]: vconfig set_ingress_map eth2.2 4 4 [system]: vconfig set_ingress_map eth2.2 5 5 [system]: vconfig set_ingress_map eth2.2 6 6 [system]: vconfig set_ingress_map eth2.2 7 7 [system]: vconfig set_egress_map eth2.2 0 0 [system]: vconfig set_egress_map eth2.2 1 1 [system]: vconfig set_egress_map eth2.2 2 2 [system]: vconfig set_egress_map eth2.2 3 3 [system]: vconfig set_egress_map eth2.2 4 4 [system]: vconfig set_egress_map eth2.2 5 5 [system]: vconfig set_egress_map eth2.2 6 6 [system]: vconfig set_egress_map eth2.2 7 7 [system]: vconfig add eth2 3 [system]: vconfig set_ingress_map eth2.3 0 0 [system]: vconfig set_ingress_map eth2.3 1 1 [system]: vconfig set_ingress_map eth2.3 2 2 [system]: vconfig set_ingress_map eth2.3 3 3 [system]: vconfig set_ingress_map eth2.3 4 4 [system]: vconfig set_ingress_map eth2.3 5 5 [system]: vconfig set_ingress_map eth2.3 6 6 [system]: vconfig set_ingress_map eth2.3 7 7 [system]: vconfig set_egress_map eth2.3 0 0 [system]: vconfig set_egress_map eth2.3 1 1 [system]: vconfig set_egress_map eth2.3 2 2 [system]: vconfig set_egress_map eth2.3 3 3 [system]: vconfig set_egress_map eth2.3 4 4 [system]: vconfig set_egress_map eth2.3 5 5 [system]: vconfig set_egress_map eth2.3 6 6 [system]: vconfig set_egress_map eth2.3 7 7 [system]: vconfig add eth2 4 [system]: vconfig set_ingress_map eth2.4 0 0 [system]: vconfig set_ingress_map eth2.4 1 1 [system]: vconfig set_ingress_map eth2.4 2 2 [system]: vconfig set_ingress_map eth2.4 3 3 [system]: vconfig set_ingress_map eth2.4 4 4 [system]: vconfig set_ingress_map eth2.4 5 5 [system]: vconfig set_ingress_map eth2.4 6 6 [system]: vconfig set_ingress_map eth2.4 7 7 [system]: vconfig set_egress_map eth2.4 0 0 [system]: vconfig set_egress_map eth2.4 1 1 [system]: vconfig set_egress_map eth2.4 2 2 [system]: vconfig set_egress_map eth2.4 3 3 [system]: vconfig set_egress_map eth2.4 4 4 [system]: vconfig set_egress_map eth2.4 5 5 [system]: vconfig set_egress_map eth2.4 6 6 [system]: vconfig set_egress_map eth2.4 7 7 [system]: ifconfig eth2 up [system]: ifconfig eth2.1 0.0.0.0 up [system]: ifconfig eth2.2 0.0.0.0 up [system]: ifconfig eth2.3 0.0.0.0 up [system]: ifconfig eth2.4 0.0.0.0 up [system]: ifconfig eth3 0.0.0.0 up [system]: config-vlan.sh 3 0 [system]: switch vlan set 1 1 10000011 [system]: switch vlan set 2 2 01000011 [system]: switch vlan set 3 3 00100011 [system]: switch vlan set 4 4 00010011 [system]: switch vlan set 5 5 00001100 [system]: switch reg w 2010 810000c0 [system]: switch reg w 2110 810000c0 [system]: switch reg w 2210 810000c0 [system]: switch reg w 2310 810000c0 [system]: switch reg w 2410 810000c0 [system]: switch reg w 2510 810000c0 [system]: switch reg w 2610 81000000 [system]: switch pvid 0 1 [system]: switch pvid 1 2 [system]: switch pvid 2 3 [system]: switch pvid 3 4 [system]: switch pvid 4 5 [system]: switch pvid 5 5 [system]: switch reg w 2004 ff0003 [system]: switch reg w 2104 ff0003 [system]: switch reg w 2204 ff0003 [system]: switch reg w 2304 ff0003 [system]: switch reg w 2404 ff0003 [system]: switch reg w 2504 ff0003 [system]: switch reg w 2604 20ff0003 [system]: switch reg w 2014 10001 [system]: switch reg w 2114 10002 [system]: switch reg w 2214 10003 [system]: switch reg w 2314 10004 [system]: switch vlan set 0 5 00001100 [system]: modprobe ehci-hcd [system]: modprobe ohci-hcd [system]: modprobe xhci-hcd [system]: modprobe xhci-hcd [system]: modprobe hw_nat Ralink HW NAT Module Enabled eth2 ifindex =6 eth3 ifindex =9 [system]: ralink_init make_wireless_config rt2860 [system]: ralink_init make_wireless_config rtdev [system]: ralink_init make_wireless_config wifi3 [system]: cp -rf /etc_ro/Wireless/RT2860AP/SingleSKU_24G_FCC.dat /var/Wireless/7615_SingleSKU_24G.dat [system]: cp -rf /etc_ro/Wireless/RT2860AP/SingleSKU_5G_FCC.dat /var/Wireless/7615_SingleSKU_5G.dat [system]: cp -rf /etc_ro/Wireless/RT2860AP/SKU_24G_FCC_BF.dat /var/Wireless/7615_BF_SKU_24G.dat [system]: cp -rf /etc_ro/Wireless/RT2860AP/SKU_5G_FCC_BF.dat /var/Wireless/7615_BF_SKU_5G.dat e2p_lan mac = 60:63:4C:7C:33:01 lanmac=8139521 check_wlan_mac:wlan_2g_mac=8139522,wlan_5g_mac=8139523,lanmac=8139521 wan mac = 60:63:4C:7C:33:05 wanmac=8139525 mydlink UID = ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ mydlink number = 39921188 [system]: /etc/init.d/stad restart [system]: ln -sf /tmp/resolv.conrecv is :Hello you! f /etc/resolv.conf [system]: ln -sf /tmp/hosts /etc/hosts certificate req and private key is ok [system]: echo -n bGl1c2hlbmdodWk= > /tmp/dhcp6sctlkey sysinit: done [system]: fota_config init rc_ubus_init: rc_ubus_init Connected to ubus, id=5df18e28 [system]: /etc/init.d/timer restart start_timer: stimer calls setitimer() with new_value NULL pointer. Misfeature support will be removed tart timer done rc_services_init: init.c rc_services_init 1659 set_action: 291: set_action 10 ESW: Link Status Changed - Port1 Link UP start_lan_br: enter [system]: brctl addbr br0 [system]: brctl addif br0 eth2.1 device eth2.1 entered promiscuous mode device eth2 entered promiscuous mode [system]: brctl addif br0 eth2.2 device eth2.2 entered promiscuous mode [system]: brctl addif br0 eth2.3 device eth2.3 entered promiscuous mode [system]: brctl addif br0 eth2.4 device eth2.4 entered promiscuous mode [system]: brctl addif br0 ra0 [system]: brctl addif br0 rax0 [system]: brctl addif br0 rai0 [system]: brctl addif br0 ra1 [system]: brctl addif br0 rax1 [system]: brctl addif br0 rai1 [system]: brctl addbr br1 [system]: brctl addbr br2 [system]: brctl addbr br3 start_lan_br: done [system]: mii_mgr -s -p 0 -r 0 -v 3900 [system]: mii_mgr -s -p 1 -r 0 -ESW: Link Status Changed - Port1 Link Down v 3900 [system]: mii_mgr -s -p 2 -r 0 -v 3900 [system]: mii_mgr -s -p 3 -r 0 -v 3900 wait_action_idle: pid 291 preinit hold action lock 10 !!! [system]: mii_mgr -s -p 0 -r 0 -v 3300 [system]: mii_mgr -s -p 1 -r 0 -v 3300 [system]: mii_mgr -s -p 2 -r 0 -v 3300 [system]: mii_mgr -s -p 3 -r 0 -v 3300 [system]: iwpriv rax0 set KickAll=1 [system]: iwpriv ra0 set KickAll=1 [system]: iwpriv rax1 set KickAll=1 [system]: iwpriv ra1 set KickAll=1 [system]: iwpriv ra3 set KickAll=1 [system]: iwpriv rai0 set KickAll=1 [system]: iwpriv rai1 set KickAll=1 [system]: iwpriv rai3 set KickAll=1 br0: port 4(eth2.4) entered forwarding state br0: port 4(eth2.4) entered forwarding state br0: port 3(eth2.3) entered forwarding state br0: port 3(eth2.3) entered forwarding state br0: port 2(eth2.2) entered forwarding state br0: port 2(eth2.2) entered forwarding state br0: port 1(eth2.1) entered forwarding state br0: port 1(eth2.1) entered forwarding state IPv6: ADDRCONF(NETDEV_UP): imq0: link is not ready IPv6: ADDRCONF(NETDEV_UP): imq1: link is not ready IPv6: ADDRCONF(NETDEV_UP): ra0: link is not ready IPv6: ADDRCONF(NETDEV_UP): rai0: link is not ready IPv6: ADDRCONF(NETDEV_UP): sit0: link is not ready IPv6: ADDRCONF(NETDEV_UP): ip6tnl0: link is not ready IPv6: ADDRCONF(NETDEV_UP): br1: link is not ready IPv6: ADDRCONF(NETDEV_UP): br2: link is not ready IPv6: ADDRCONF(NETDEV_UP): br3: link is not ready start_lan_ipv6: br0: port 4(eth2.4) entered disabled state enter br0: port 3(eth2.3) entered disabled state br0: port 2(eth2.2) entered disabled state br0: port 1(eth2.1) entered disabled state br0: port 4(eth2.4) entered forwarding state br0: port 4(eth2.4) entered forwarding state br0: port 3(eth2.3) entered forwarding state br0: port 3(eth2.3) entered forwarding state br0: port 2(eth2.2) entered forwarding state br0: port 2(eth2.2) entered forwarding state br0: port 1(eth2.1) entered forwarding state br0: port 1(eth2.1) entered forwarding state [system]: echo "192.168.1.1" > /proc/guestzoneisolation/gateway [system]: brctl addif br0 ra3 [system]: brctl addif br0 rai3 start_dev_mgt_link: enter tmpTo[dir3060] [system]: hostname dir3060 [system]: nl_server -i br0 -s dir3060 -s dir30603301 -s dir3060.local -s dir30603301.local & start_mdns_responder: enter tmpTo[dir3060] [system]: mDNSResponder -b -i br0 -f /tmp/mdns_resp.conf -e dir3060 -e dir30603301 [system]: mdnsd start_mdns_responder: done start_dev_mgt_link: done [system]: /etc/init.d/dnsmasq stop [system]: rm -f /tmp/dnsmasq.leases [system]: /etc/init.d/dnsmasq restart [system]: echo 1 > /proc/net/arp_spoofing_enable [system]: ubus call ifmon_service register \{\"name\":\"wan_wan0\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\":\"wan_wan1\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\":\"wan_wan2\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\":\"wan_wan3\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: switch reg w 2014 10001 [system]: switch reg w 2114 10002 [system]: switch reg w 2214 10003 [system]: switch reg w 2314 10004 [system]: switch vlan set 0 5 00001100 Start lighttpd ... [system]: /etc/init.d/lighttpd restart wait_action_idle: pid 291 preinit hold action lock 10 !!! [system]: /etc/init.d/timer restart start_timer: start timer done TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan1_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan2_ TRACE public/public.c: 489 TW_multiwan_get_use_wan_prefix: prefix=wan_wan3_ [system]: syslogd -L TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: omcproxy -e1 & [system]: /etc/init.d/smbd stop [system]: rm -rf /etc/smb.conf [system]: rm -f /var/etc/samba/smbpasswd [system]: rm -f /var/etc/samba/config/* start_samba: SAMBA_Enabled not set!Please use:nvram_set SAMBA_Enabled 1 [system]: rm -rf /etc/ftpd.conf [system]: rm -rf /etc/minidlna.conf [system]: /mydlink/mydlink_watchdog.sh start_services: done radvd_conf: done : radvd_conf start_radvd: done : restart radvd [system]: ubus call ifmon_service register \{\"name\":\"wan_wan0\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\":\"wan_wan1\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\":\"wan_wan2\",\"ifname\":\"eth3\",\"type\":\"link\"\} [system]: ubus call ifmon_service register \{\"name\"DriverOwn()::Return since already in Driver Own... :\"wan_wan3\",\"APWdsInitialize():WdsEntry[0] ifname\":\"eth3\APWdsInitialize():WdsEntry[1] ",\"type\":\"linAPWdsInitialize():WdsEntry[2] k\"\} [system]APWdsInitialize():WdsEntry[3] : mii_mgr -s -p [wifi_fwd_set_cb_num] band_cb_offset=33, recv_from_cb_offset=34 4 -r 0 -v 3900 [system]: mii_mgr -s -p 4 -r 0 -v 3300 start_wlan()============>in [system]: ifconfig ra0 up multi-profile merge success, en:1,pf1_num:4,pf2_num:2,total:6 MacAddress4 = 00:00:00:00:00:00 E2pAccessMode=2 SSID[0]=hoffman, EdcaIdx=0 SSID[1]=dlink-guest, EdcaIdx=0 SSID[2]=dlink_reserve, EdcaIdx=0 SSID[3]=mesh_7C3301, EdcaIdx=0 SSID[4]=hoffman, EdcaIdx=0 SSID[5]=dlink-guest, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=1 TriBandChGrp=0/0/0/0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=9 cfg_mode=9 cfg_mode=9 cfg_mode=9 BandSteering=1 BndStrgBssIdx=1;1;0;0;1;1 [TxPower] BAND0: 100, BAND1: 100 [SKUenable] BAND0: 1, BAND1: 1 [PERCENTAGEenable] BAND0: 1, BAND1: 0 [BFBACKOFFenable] BAND0: 0, BAND1: 0 CalCacheApply = 0 APEdca0 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca1 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca2 APEdca3 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 APSDCapable[0]=0 APSDCapable[1]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: WDEV[0] Ext Channel = ABOVE HT: WDEV[1] Ext Channel = ABOVE HT: WDEV[2] Ext Channel = ABOVE HT: WDEV[3] Ext Channel = ABOVE HT: WDEV[4] Ext Channel = ABOVE HT: WDEV[5] Ext Channel = ABOVE HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:82, BssidNum:6, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:120 Top Init Done! Use alloc_skb RX[0] DESC a0c14000 size = 16384 RX[1] DESC a0c12000 size = 8192 Hif Init Done! ctl->txq = c258bdc0 ctl->rxq = c258bdcc ctl->ackq = c258bdd8 ctl->kickq = c258bde4 ctl->tx_doneq = c258bdf0 ctl->rx_doneq = c258bdfc mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2687): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(11102) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170809192718a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(462248) Build Date:_201810011428 Build Date:_201810011428 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201707211524 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done!  MtCmdSetRlmPorCal: (ret = 0) efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] NICReadEEPROMParameters: EEPROM 0x52 b302 NICReadEEPROMParameters: EEPROM 0x52 b302 ESW: Link Status Changed - Port1 Link UP [modules/TW_Mydlink.c:GetMyDLinkSettings:141]pcResponseData=<soap:Envelope xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:soap="http://schemas.xmlsoap.org/soap/envelope/"> <soap:Body><GetMyDLinkSettingsResponse xmlns="http://purenetworks.com/HNAP1/"> <GetMyDLinkSettingsResult>OK</GetMyDLinkSettingsResult> <Enabled>true</Enabled> <Email></Email> <AccountStatus>false</AccountStatus> <MyDLinkNo>39921188</MyDLinkNo> </GetMyDLinkSettingsResponse> </soap:Body> </soap:Envelope> wait_action_idle: pid 291 preinit hold action lock 10 !!! wait_action_idle: pid 291 preinit hold action lock 10 !!! wait_action_idle: pid 291 preinit hold action lock 10 !!! wait_action_idle: pid 291 preinit hold action lock 10 !!! br0: port 4(eth2.4) entered forwarding state br0: port 3(eth2.3) entered forwarding state br0: port 2(eth2.2) entered forwarding state br0: port 1(eth2.1) entered forwarding state wait_action_idle: pid 291 preinit hold action lock 10 !!! wait_action_idle: pid 291 preinit hold action lock 10 !!! Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(233): Don't Support this now! RTMPReadTxPwrPerRate(1381): Don't Support this now! RcRadioInit(): DbdcMode=1, ConcurrentBand=2 RcRadioInit(): pRadioCtrl=8b770454,Band=0,rfcap=1,channel=1,PhyMode=2 extCha=0xf RcRadioInit(): pRadioCtrl=8b770540,Band=1,rfcap=2,channel=36,PhyMode=1 extCha=0xf MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 Band Rf: 2, Phy Mode: 1 AntCfgInit(2770): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtSingleSkuLoadParam: SINGLE SKU TABLE FILE /var/Wireless/7615_SingleSKU_24G.dat!!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: BF SKU TABLE FILE /var/Wireless/7615_BF_SKU_24G.dat!!! EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2747): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1300): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=2/49, support 20 channels ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup = 1, AutoChannelFlag = 63 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) ==================================================================== Channel 36 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 40 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 44 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 48 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 36 Rule 3 Channel Busy time value : Min Channel Busy = 0 Rule 3 Channel Busy time value : BW = 80  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 36  wait_action_idle AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 36  : pid 291 preini AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 36  t hold action lo AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 14,Channel = 0  ck 10 !!!  AutoChSelUpdateChannel(): Update channel for wdev5 for this band PhyMode = 14,Channel = 0  mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) ==================================================================== Channel 3 : Busy Time = 3702, Skip Channel = FALSE, BwCap = TRUE Channel 6 : Busy Time = 4280, Skip Channel = FALSE, BwCap = TRUE Channel 9 : Busy Time = 3215, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 9 Rule 3 Channel Busy time value : Min Channel Busy = 3215 Rule 3 Channel Busy time value : BW = 20  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 14,Channel = 9   AutoChSelUpdateChannel(): Update channel for wdev5 for this band PhyMode = 14,Channel = 9  ApAutoChannelAtBootUp<----------------- WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = 60:63:4c:7c:33:03 MtCmdSetDbdcCtrl:(ret = 0) Current Channel is 36. DfsZeroWaitSupport=0 MtAsicSetChBusyStat(840): Not support for HIF_MT yet! MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=2/49, support 20 channels Enable 20/40 BSSCoex Channel Scan(BssCoex=1) wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 MtCmdSetDbdcCtrl:(ret = 0)  [RadarStateCheck]Set into RD_NORMAL_MODE  MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 1 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2605): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2584): Not support for HIF_MT yet! RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! WifiFwdSet::disabled=0 BndStrg_Init() Main bssid = 60:63:4c:7c:33:03 AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) MCS Set = ff ff 00 00 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 0 WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 Total allocated 4 WDS interfaces! WtcSetMaxStaNum: MaxStaNum:82, BssidNum:6, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:120 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. BndStrg_SetInfFlags(): BSS(60:63:4C:7C:33:03) set 5G Inf ra0 ready. Correct apidx from 1 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c22fb188, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 60 63 4c 7c 33 03 ifconfig ra0 up [system]: ifconfig ra0 down WifiSysClose(), wdev idx = 0 ExtEventBeaconLostHandler::FW LOG, Beacon lost (60:63:4c:7c:33:03), Reason 0x10 Beacon lost - AP disabled!!! WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!! WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!! BndStrg_SetInfFlags(): BSS(60:63:4C:7C:33:03) set 5G Inf ra0 not ready. MtAsicSetPiggyBack(777): Not support for HIF_MT yet! RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0! WifiSysClose(), wdev idx = 0 BndStrg_SetInfFlags(): 5G Inf ra0 Band steering is already down. WifiSysClose(), wdev idx = 1 BndStrg_SetInfFlags(): 5G Inf ra1 Band steering is already down. WifiSysClose(), wdev idx = 2 BndStrg_SetInfFlags(): 5G Inf ra2 Band steering is already down. WifiSysClose(), wdev idx = 3 BndStrg_SetInfFlags(): 5G Inf ra3 Band steering is already down. MtAsicSetPiggyBack(777): Not support for HIF_MT yet! RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0! WifiSysClose(), wdev idx = 4 BndStrg_SetInfFlags(): 2G Inf rax0 Band steering is already down. WifiSysClose(), wdev idx = 5 BndStrg_SetInfFlags(): 2G Inf rax1 Band steering is already down. kill LoopBackTxTask task failed! RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=4, LED_CMD=1! AndesRestartCheck: Current TOP_MISC2(0x7) CmdReStartDLRsp: Status Success!, Status(0) AndesRestartCheck: TOP_MISC2(1) RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=2, LED_CMD=1! RT28xxPciAsicRadioOff(): Not support for HIF_MT yet! RTMPDrvClose call RT28xxPciAsicRadioOff fail !! tx_kickout_fail_count = 0 tx_timeout_fail_count = 0 rx_receive_fail_count = 0 alloc_cmd_msg = 1267 free_cmd_msg = 1267 cut_through_token_list_destroy(): 8da00208,8da00208 cut_through_token_list_destroy(): 8da00218,8da00218 FwOwn()::Set Fw Own BndStrg_Release() BndStrg_SetInfFlags(): 5G Inf ra0 Band steering is already down. BndStrg_SetInfFlags(): 5G Inf ra1 Band steering is already down. BndStrg_SetInfFlags(): 5G Inf ra2 Band steering is already down. BndStrg_SetInfFlags(): 5G Inf ra3 Band steering is already down. BndStrg_SetInfFlags(): 2G Inf rax0 Band steering is already down. BndStrg_SetInfFlags(): 2G Inf rax1 Band steering is already down. RTMP_AllTimerListRelease: Size=32 RTMP_AllTimerListRelease: Cancel timer obj c22fb3d4! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c22fb408! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c22fef98! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c22fefcc! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2302b5c! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2302b90! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2306720! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2306754! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c230a2e4! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c230a318! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c230dea8! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c230dedc! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2311a6c! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2311aa0! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2315630! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2315664! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c23191f4! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2319228! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c231cdb8! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c231cdec! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c232097c! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c23209b0! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2324540! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2324574! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2328104! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2328138! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c232bcc8! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c232bcfc! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c232f88c! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c232f8c0! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2333450! RTMP_AllTimerListRelease: Timer is allocated by 0x814406ec,Valid:1,Lock:c258e76c,State:0 RTMP_AllTimerListRelease: Cancel timer obj c2333484! RTMP_AllTimerListRelease: Timer is allocated by 0x81440708,Valid:1,Lock:c258e76c,State:0 FwOwn()::Return since already in Fw Own... <---HwCtrlThread ***********PpeDevUnRegHandler ***********PpeDevUnRegHandler ***********PpeDevUnRegHandler [system]: ifconfig ra1 down [system]: ralink_init make_wireless_config rtdev [system]: ifconfig rai0 down [system]: ifconfig rai1 down [system]: ralink_init make_wireless_config wifi3 wait_action_idle: pid 291 preinit hold action lock 10 !!! [system]: ifconfig rax0 down [system]: ifconfig rax1 down [system]: ralink_init make_wireless_config rt2860 [system]: ifconfig ra0 up DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] [wifi_fwd_set_cb_num] band_cb_offset=33, recv_from_cb_offset=34 multi-profile merge success, en:1,pf1_num:4,pf2_num:2,total:6 MacAddress4 = 00:00:00:00:00:00 E2pAccessMode=2 SSID[0]=hoffman, EdcaIdx=0 SSID[1]=dlink-guest, EdcaIdx=0 SSID[2]=dlink_reserve, EdcaIdx=0 SSID[3]=mesh_7C3301, EdcaIdx=0 SSID[4]=hoffman, EdcaIdx=0 SSID[5]=dlink-guest, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=1 TriBandChGrp=0/0/0/0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=14 cfg_mode=9 cfg_mode=9 cfg_mode=9 cfg_mode=9 BandSteering=1 BndStrgBssIdx=1;1;0;0;1;1 [TxPower] BAND0: 100, BAND1: 100 [SKUenable] BAND0: 1, BAND1: 1 [PERCENTAGEenable] BAND0: 1, BAND1: 0 [BFBACKOFFenable] BAND0: 0, BAND1: 0 CalCacheApply = 0 APEdca0 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca1 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca2 APEdca3 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 APSDCapable[0]=0 APSDCapable[1]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: WDEV[0] Ext Channel = ABOVE HT: WDEV[1] Ext Channel = ABOVE HT: WDEV[2] Ext Channel = ABOVE HT: WDEV[3] Ext Channel = ABOVE HT: WDEV[4] Ext Channel = ABOVE HT: WDEV[5] Ext Channel = ABOVE HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:82, BssidNum:6, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:120 Top Init Done! Use alloc_skb cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8e5cb988,8e5cb988 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8e5cb998,8e5cb998 RX[0] DESC a0c14000 size = 16384 RX[1] DESC a0c12000 size = 8192 Hif Init Done! ctl->txq = c258bdc0 ctl->rxq = c258bdcc ctl->ackq = c258bdd8 ctl->kickq = c258bde4 ctl->tx_doneq = c258bdf0 ctl->rx_doneq = c258bdfc mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2687): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(11102) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170809192718a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=1 MtCmdPatchSemGet:(ret = 0) Patch is ready, continue to ILM/DLM DL, SemStatus(1) Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(462248) Build Date:_201810011428 Build Date:_201810011428 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201707211524 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! MtCmdSetTxLpfCal:(ret = 0) MtCmdSetTxIqCal:(ret = 0) MtCmdSetTxDcCal:(ret = 0) MtCmdSetRxFiCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0) MtCmdSetRxFdCal:(ret = 0)  MtCmdSetRlmPorCal: (ret = 0) efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] NICReadEEPROMParameters: EEPROM 0x52 b302 NICReadEEPROMParameters: EEPROM 0x52 b302 Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(233): Don't Support this now! RTMPReadTxPwrPerRate(1381): Don't Support this now! RcRadioInit(): DbdcMode=1, ConcurrentBand=2 RcRadioInit(): pRadioCtrl=8b770454,Band=0,rfcap=1,channel=1,PhyMode=2 extCha=0xf RcRadioInit(): pRadioCtrl=8b770540,Band=1,rfcap=2,channel=36,PhyMode=1 extCha=0xf MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 Band Rf: 2, Phy Mode: 1 AntCfgInit(2770): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtSingleSkuLoadParam: SINGLE SKU TABLE FILE /var/Wireless/7615_SingleSKU_24G.dat!!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: BF SKU TABLE FILE /var/Wireless/7615_BF_SKU_24G.dat!!! EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2747): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1300): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=2/49, support 20 channels ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup = 1, AutoChannelFlag = 63 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) wait_action_idle: pid 291 preinit hold action lock 10 !!! mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(1) ==================================================================== Channel 36 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 40 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 44 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 48 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 36 Rule 3 Channel Busy time value : Min Channel Busy = 0 Rule 3 Channel Busy time value : BW = 80  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 14,Channel = 0   AutoChSelUpdateChannel(): Update channel for wdev5 for this band PhyMode = 14,Channel = 0  mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) ==================================================================== Channel 3 : Busy Time = 3805, Skip Channel = FALSE, BwCap = TRUE Channel 6 : Busy Time = 3147, Skip Channel = FALSE, BwCap = TRUE Channel 9 : Busy Time = 2067, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 9 Rule 3 Channel Busy time value : Min Channel Busy = 2067 Rule 3 Channel Busy time value : BW = 20  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 36   AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 14,Channel = 9   AutoChSelUpdateChannel(): Update channel for wdev5 for this band PhyMode = 14,Channel = 9  ApAutoChannelAtBootUp<----------------- WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = 60:63:4c:7c:33:03 MtCmdSetDbdcCtrl:(ret = 0) Current Channel is 36. DfsZeroWaitSupport=0 [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=36 CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=2/49, support 20 channels Enable 20/40 BSSCoex Channel Scan(BssCoex=1) wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 MtCmdSetDbdcCtrl:(ret = 0)  [RadarStateCheck]Set into RD_NORMAL_MODE  MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 1 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) BndStrg_SetInfFlags(): BSS(60:63:4C:7C:33:03) set 5G Inf ra0 ready. LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2605): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2584): Not support for HIF_MT yet! :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! WifiFwdSet::disabled=0 BndStrg_Init() Main bssid = 60:63:4c:7c:33:03 AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) MCS Set = ff ff 00 00 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 0 WtcSetMaxStaNum: MaxStaNum:82, BssidNum:6, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:120 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. BndStrg_SetInfFlags(): 5G Inf ra0 Band steering is already up. Correct apidx from 1 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c22fb188, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 60 63 4c 7c 33 03 [system]: iwpriv ra0 set IgmpSnEnable=1 [system]: iwpriv ra0 set WscUUID_E=d1087a18aae3b8153a5b60634C7C3301 [system]: iwpriv ra0 set WscUUID_Str=d1087a18-aae3-b815-3aDriverOwn()::Return since already in Driver Own... 5b-60634C7C3301 APWdsInitialize():WdsEntry[0] [system]: ifcoAPWdsInitialize():WdsEntry[1] nfig rai0 up APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] [wifi_fwd_set_cb_num] band_cb_offset=33, recv_from_cb_offset=34 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap_5G.dat Open file "/etc/Wireless/iNIC/iNIC_ap_5G.dat" failed! E2pAccessMode=2 SSID[0]=hoffman, EdcaIdx=0 SSID[1]=dlink-guest, EdcaIdx=0 SSID[2]=, EdcaIdx=0 SSID[3]=mesh_7C3301, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=0 TriBandChGrp=0/0/0/0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! BandSteering=1 BndStrgBssIdx=1;1 [TxPower] BAND0: 100 [SKUenable] BAND0: 1 [PERCENTAGEenable] BAND0: 0 [BFBACKOFFenable] BAND0: 0 CalCacheApply = 0 APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: WDEV[0] Ext Channel = ABOVE HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:84, BssidNum:4, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122 Top Init Done! Use alloc_skb RX[0] DESC a0ca4000 size = 16384 RX[1] DESC a0ca2000 size = 8192 Hif Init Done! ctl->txq = c2a8bdc0 ctl->rxq = c2a8bdcc ctl->ackq = c2a8bdd8 ctl->kickq = c2a8bde4 ctl->tx_doneq = c2a8bdf0 ctl->rx_doneq = c2a8bdfc mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2687): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(11102) AndesRestartCheck: Current TOP_MISC2(0x1) wait_action_idleAndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 2: pid 291 preini0t hold action lo1ck 10 !!! 70809192718a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(462248) Build Date:_201810011428 Build Date:_201810011428 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201707211524 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000] NICReadEEPROMParameters: EEPROM 0x52 b302 NICReadEEPROMParameters: EEPROM 0x52 b302 wait_action_idle: pid 291 preinit hold action lock 10 !!! AUTH-true [DLINK_VENDOR_CHECK] STA associated. [DLINK_VENDOR_CHECK] STA authorized. AP SETKEYS DONE - AKMMap=WPA2PSK, PairwiseCipher=AES, GroupCipher=TKIP, wcid=1 from EE:44:6E:C8:20:DE PTK:2143251c17ad8d7ae5b2f2e92e09cbb7e3152543ab922d1d62b42c7716e52cd4ef84093cbd9c2b987725edb0b59f6ba716f77b5f4deff27e7ef99e1d79a8f03d pSsid=hoffman RRM_EnqueueNeighborRep() : send Neighbor RSP wait_action_idle: pid 291 preinit hold action lock 10 !!! Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(233): Don't Support this now! RTMPReadTxPwrPerRate(1381): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=8e00e454,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 AntCfgInit(2770): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtSingleSkuLoadParam: SINGLE SKU TABLE FILE /var/Wireless/7615_SingleSKU_5G.dat!!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: BF SKU TABLE FILE /var/Wireless/7615_BF_SKU_5G.dat!!! EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2747): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1300): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=49/49, support 9 channels ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup = 1, AutoChannelFlag = 1 MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 149,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 157,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 161,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(1) ==================================================================== Channel 149 : Busy Time = 701, Skip Channel = FALSE, BwCap = TRUE Channel 153 : Busy Time = 648, Skip Channel = FALSE, BwCap = TRUE Channel 157 : Busy Time = 1536, Skip Channel = FALSE, BwCap = TRUE Channel 161 : Busy Time = 25, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 149 Rule 3 Channel Busy time value : Min Channel Busy = 1536 Rule 3 Channel Busy time value : BW = 80  AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 149   AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 149   AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 149   AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 149  wait_action_idleApAutoChannelAtBootUp<----------------- : pid 291 preiniWifiSysOpen(), wdev idx = 0 t hold action lowdev_attr_update(): wdevId0 = 60:63:4c:7c:33:04 ck 10 !!! MtCmdSetDbdcCtrl:(ret = 0) Current Channel is 149. DfsZeroWaitSupport=0 MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=149 CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=49/49, support 9 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196  [RadarStateCheck]Set into RD_NORMAL_MODE  MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155 mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 149,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2605): Not support for HIF_MT yet! MtAsicSetPiggyBack(777): Not support for HIF_MT yet! MtAsicSetTxPreamble(2584): Not support for HIF_MT yet! RTMPSetLED()---------------------------->YBS----556 RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! WifiFwdSet::disabled=0 BndStrg_Init() Main bssid = 60:63:4c:7c:33:04 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) MCS Set = ff ff ff ff 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 Total allocated 4 WDS interfaces! WtcSetMaxStaNum: MaxStaNum:84, BssidNum:4, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:122 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. BndStrg_SetInfFlags(): BSS(60:63:4C:7C:33:04) set 5G Inf rai0 ready. Correct apidx from 0 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c27fb188, len = 16 0x0000 : d1 08 7a 18 aa e3 b8 15 3a 5b 60 63 4c 7c 33 01 [system]: iwpriv rai0 set IgmpSnEnable=1 [system]: iwpriv rai0 set WscUUID_E=d1087a18aae3b8153a5b60634C7C3301 [system]: iwpriv rai0 set WscUUID_Str=d1087a18-aae3-b815-3a5b-60634C7C3301 [system]: ifWifiSysOpen(), wdev idx = 4 config rax0 up wdev_attr_update(): wdevId4 = 60:63:4c:7c:33:02 MtCmdSetDbdcCtrl:(ret = 0) [PMF]APPMFInit:: apidx=4, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=9 CountryCode(2.4G/5G)=0/10, RFIC=25, PHY mode(2.4G/5G)=14/49, support 20 channels Enable 20/40 BSSCoex Channel Scan(BssCoex=1) MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [2] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) mt7615_apply_dcoc() : reload Central CH [4] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [5] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [7] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l wait_action_idle: pid 291 preinit hold action lock 10 !!! mt7615_apply_dcoc() : reload Central CH [8] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [10] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [11] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(1) AP OBSS SYNC - BBP R4 to 20MHz.l wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:126 for WDEV_TYPE:1 LinkToOmacIdx = 14, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 MtCmdSetDbdcCtrl:(ret = 0)  [RadarStateCheck]Set into RD_NORMAL_MODE  MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 mt7615_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=9, HT-CentCh=9, VHT-CentCh=42 mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 2, RXStream = 2, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 9(Prim=9, HT-CentCh=9, VHT-CentCh=42, BBP_BW=0) BndStrg_SetInfFlags(): BSS(60:63:4C:7C:33:02) set 2G Inf rax0 ready. LeadTimeForBcn, OmacIdx = 14, WDEV_WITH_BCN_ABILITY Generate UUID for apidx(4) UUID: c230a098, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 60 63 4c 7c 33 02 [system]: iwpriv rax0 set IgmpSnEnable=1 [system]: iwpriv rax0 set WscUUID_E=d1087a18aae3b8153a5b60634C7C3301 [system]: iwpriv rax0 set WscUUID_Str=d1087a18-aae3-b815-3a5b-60634C7C3301 #### gjf: start BandSteering! ####### [system]: bndstrg2 -i ra0 -i rai0 -i rax0 [system]: iwpriv rax0 set WscSetupLock=1 [system]: iwpriv ra0 set WscSetupLock=1 [system]: iwpriv rai0 set WscSetupLock=1 [system]: iwpriv rax0 set WscConfMode=0 [system]: iwpriv ra0 set WscConfMode=0 [systedevice ra0 entered promiscuous mode m]: iwpriv rai0 br0: port 5(ra0) entered forwarding state set WscConfMode=br0: port 5(ra0) entered forwarding state 0 [system]: brctl addif br0 ra0 [system]: brdevice rax0 entered promiscuous mode ctl addif br0 rabr0: port 6(rax0) entered forwarding state x0 br0: port 6(rax0) entered forwarding state [system]: brctl addif br0 rai0 device rai0 entered promiscuous mode br0: port 7(rai0) entered forwarding state br0: port 7(rai0) entered forwarding state [system]: brctl addif br0 ra1 [system]: brctl addif br0 rax1 [system]: brctl addif br0 rai1 [system]: echo "192.168.1.1" > /proc/guestzoneisolation/gateway [system]: echo "rax1,ra1,rai1" > /proc/guestzoneisolation/ifaceList [services]get_gateway_v6:buf[fe80::6263:4cff:fe7c:3301 ] fe80:0000:0000:0000:6263:4cff:fe7c:3301[services]get_gateway_v6:ipv6_gate[fe80:0000:0000:0000:6263:4cff:fe7c:3301] [system]: echo "fe80:0000:0000:0000:6263:4cff:fe7c:3301" > /proc/guestzoneisolation/gateway_v6 [system]: iwpriv rax1 set IPV6Disable=1 [system]: iwpriv ra1 set IPV6Disable=1 [system]: iwpriv rai1 set IPV6Disable=1 start_wlan()============>out start_schedule: enter Time synchronization has not been completed. We don't turn on scheduling. [system]: echo 1 > /proc/hw_nat/ipv6_hw_nat TRACE acl/acl.c: 116 upload_ping_block_rules: <--wan ping start--> [system]: iptables -t filter -D INPUT -j ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -F ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -X ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -N ACL_PING_INPUT 2>/dev/null [system]: iptables -t filter -A INPUT -j ACL_PING_INPUT 2>/dev/null TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE acl/acl.c: 129 upload_ping_block_rules: max_wan_num=1 [system]: iptables -t filter -A ACL_PING_INPUT -i eth3 -p ICMP -m state --state NEW -j DROP 2>/dev/null TRACE antiattack/antiattack.c:1002 TW_Anti_Spoofing_run: <--Anti Spoofing start--> [system]: iptables -t filter -F ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -X ANTI_SPOOFING_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1008 TW_Anti_Spoofing_run: <--Anti Spoofing is disable--> TRACE firewallfilter/firewallfilter.c: 197 FIREWALL_FILTER_run: <--firewall filter start--> [system]: iptables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 236 FIREWALL_FILTER_run: firewall filter disabled TRACE firewallfilter/firewallfilter.c: 883 FIREWALL_IPv6_FILTER_run: <--firewall ipv6 filter start--> [system]: ip6tables -t filter -D FORWARD -j FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -F FIREWALL_FILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -X FIREWALL_FILTER_FORWARD 2>/dev/null TRACE firewallfilter/firewallfilter.c: 928 FIREWALL_IPv6_FILTER_run: firewall ipv6 filter disabled TRACE macfilter/macfilter.c: 149 MACFILTER_run: <--mac filter start--> [system]: iptables -t filter -D FORWARD -j MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -F MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -X MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -N MACFILTER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j MACFILTER_FORWARD 2>/dev/null ERROR macfilter/macfilter.c: 206 MACFILTER_run: mac filter rule is null TRACE macfilter/macfilter6.c: 138 MACFILTER6_run: <--mac filter6 start--> [system]: ip6tables -t filter -D FORWARD -j MACFILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -F MACFILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -X MACFILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -N MACFILTER_FORWARD 2>/dev/null [system]: ip6tables -t filter -A FORWARD -j MACFILTER_FORWARD 2>/dev/null ERROR macfilter/macfilter6.c: 191 MACFILTER6_run: mac filter6 rule is null TRACE urlfilter/urlfilter.c: 424 upload_url_filter_rules: <--url filter start--> ERROR urlfilter/urlfilter.c: 470 upload_url_filter_rules: url filter rule is null TRACE urlfilter/urlfilter6.c: 423 upload_url_filter6_rules: <--url filter start--> ERROR urlfilter/urlfilter6.c: 469 upload_url_filter6_rules: url filter rule is null TRACE remotemange/remotemange.c: 105 REMOTEMANGE_run: <--remotemange start--> [system]: iptables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: iptables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: iptables -t filter -X REMOTEMANGE_INPUT 2>/dev/null TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t filter -A REMOTEMANGE_INPUT -p TCP -i br+ --dport 443 -j ACCEPT TRACE remotemange/remotemange.c: 155 REMOTEMANGE_run: eth3,dhcp,wan_wan0_ ERROR remotemange/remotemange.c: 160 REMOTEMANGE_run: wan ip is null TRACE virtualserver/virtualserver.c: 231 VIRTUALSERVER_run: <--virtualserver start--> [system]: iptables -t nat -D PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -F VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -X VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -F VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -X VIRTUALSERVER_FORWARD 2>/dev/null [system]: cat /proc/net/arp|awk '/0x6/{print $0}'|awk '/^[1-9]/{print "arp -d " $1}' | sh -x [system]: iptables -t nat -N VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -A PREROUTING -j VIRTUALSERVER_PREROUTING 2>/dev/null [system]: iptables -t nat -N VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j VIRTUALSERVER_POSTROUTING 2>/dev/null [system]: iptables -t filter -N VIRTUALSERVER_FORWARD 2>/dev/null [system]: iptables -t filter -A FORWARD -j VIRTUALSERVER_FORWARD 2>/dev/null TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE virtualserver/virtualserver.c: 289 VIRTUALSERVER_run: eth3,dhcp,wan_wan0_ ERROR virtualserver/virtualserver.c: 293 VIRTUALSERVER_run: wan ip is null ERROR virtualserver/virtualserver.c: 60 WOL_Rule_Run: WOL rule is null TRACE portforward/portforward.c: 177 PORTFORWARD_run: <--portforward start--> [system]: iptables -t nat -D PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -F PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -X PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -F PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t filter -X PORTFORWARD_FORWARD 2>/dev/null [system]: iptables -t nat -N PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -A PREROUTING -j PORTFORWARD_PREROUTING 2>/dev/null [system]: iptables -t nat -N PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j PORTFORWARD_POSTROUTING 2>/dev/null [system]: iptTING 2>/dev/null [system]: iptables -t nat -F DMZ_POSTROUTING 2>/dev/null [system]: iptables -t nat -X DMZ_POSTROUTING 2>/dev/null [system]: iptables -t filter -D FORWARD -j DMZ_FORWARD 2>/dev/null [system]: iptables -t filter -F DMZ_FORWARD 2>/dev/null [system]: iptables -t nat -X DMZ_FORWARD 2>/dev/null TRACE miniupnpd/miniupnpd.c: 600 iptables_upnp_run: <--iptables upnp start--> TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ TRACE miniupnpd/miniupnpd.c: 618 iptables_upnp_run: eth3,dhcp,wan_wan0_ [system]: iptables -t nat -F MINIUPNPD 2>/dev/null [system]: iptables -t nat -D PREROUTING -i eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t nat -X MINIUPNPD 2>/dev/null [system]: iptables -t filter -F MINIUPNPD 2>/dev/null [system]: iptables -t filter -D FORWARD -i eth3 ! -o eth3 -j MINIUPNPD 2>/dev/null [system]: iptables -t filter -X MINIUPNPD 2>/dev/null nf_conntrack_rtsp v0.7 loading TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_nf_nat_rtsp v0.7 loading count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -F PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -D PREROUTIN BndStrg_InfStatusRsp:INF [ra0]STATUS QUERY ON G -i eth3 -j PRE BndStrg_InfStatusRsp:INF [rai0]STATUS QUERY ON _WAN_INFILTER 2> BndStrg_InfStatusRsp:INF [rax0]STATUS QUERY ON /dev/null [system]: iptables -t nat -X PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -N PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PREROUTING -i eth3 -j PRE_WAN_INFILTER 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -m state --state RELATED,ESTABLISHED -j ACCEPT 2>/dev/null [system]: iptables -t nat -A PRE_WAN_INFILTER -j DROP 2>/dev/null [system]: iptables -t filter -N ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -F ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -D FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: iptables -t filter -A FORWARD -j ALG_FORWARD 2>/dev/null 1>&2 [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_nat_sip.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_pptp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/netfilter/nf_conntrack_rtsp.ko 2>/dev/null [system]: insmod /lib/modules/3.10.14+/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko 2>/dev/null [system]: iptables -t filter -D INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -F GRC_INPUT 2>/dev/null [system]: iptables -t filter -X GRC_INPUT 2>/dev/null [system]: iptables -t filter -N GRC_INPUT 2>/dev/null [system]: iptables -t filter -I INPUT -j GRC_INPUT 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -m state --state INVALID -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 0 -j DROP 2>/dev/null [system]: iptables -t filter -A GRC_INPUT -p tcp --dport 1 -j DROP 2>/dev/null [system]: iptables -t filter -D FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: iptables -t filter -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 2>/dev/null [system]: ip6tables -t filter -D FORWARD -p tcp --tcp-flags SYNattack/antiattack.c:1118 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security start--> [system]: ip6tables -t filter -F SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -D FORWARD -j SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 [system]: ip6tables -t filter -X SPI_FIREWALL_FORWARD 2>/dev/null 1>&2 TRACE antiattack/antiattack.c:1124 TW_IPv6_Simple_Security_Config: <--IPv6 Simple Security is disable--> TRACE acl/acl.c: 332 MASQUERADENAT_run: <--MASQUERADENAT start--> [system]: iptables -t nat -F POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -D POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -X POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -N POSTROUTING_MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING -j POSTROUTING_MASQUERADE 2>/dev/null TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.1.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t nat -A POSTROUTING_MASQUERADE -o eth3 -s 192.168.7.0/255.255.255.0 -j MASQUERADE 2>/dev/null [system]: iptables -t mangle -D PREROUTING -j QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_PREROUTING 2>/dev/null [system]: iptables -t mangle -D POSTROUTING -j QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -F QOS_POSTROUTING 2>/dev/null [system]: iptables -t mangle -X QOS_POSTROUTING 2>/dev/null [system]: tc qdisc del dev imq0 root 2>/dev/null [system]: tc qdisc del dev imq1 root 2>/dev/null [system]: ifconfig imq0 down [system]: ifconfig imq1 down [system]: modprobe hw_nat [system]: iwpriv rax0 set hw_nat_register=1 [system]: iwpriv ra0 set hw_nat_register=1 [system]: iwpriv rai0 set hw_nat_register=1 TRACE qos/qos.c: 291 QOS_start: QosManagementType=Off TRACE qos/qos.c: 307 QOS_start: qos is disabled TRACE public/public.c: 620 TW_get_use_wan_prefix: wan_count=2 TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan0_ TRACE public/public.c: 626 TW_get_use_wan_prefix: prefix=wan_wan1_ [system]: /sbin/flush_conntrack & [system]: ip6tables -t nat -D PREROUTING -j REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -F REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t nat -X REMOTEMANGE_PREROUTING 2>/dev/null [system]: ip6tables -t filter -D INPUT -j REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -F REMOTEMANGE_INPUT 2>/dev/null [system]: ip6tables -t filter -X REMOTEMANGE_INPUT 2>/dev/null IPV6_DISABLED. get_IPv6_wan_info fail. [system]: ip6tables -t filter -A REMOTEMANGE_INPUT ! -i br+ -p TCP -m multiport --dports 80,443 -j DROP [system]: rmmod hw_nat [system]: modprobe hw_nat [system]: iwpriv rax0 set hw_nat_register=1 [system]: iwpriv ra0 set hw_nat_register=1 [system]: iwpriv rai0 set hw_nat_register=1 [system]: led set all on [system]: gpio l 16 4000 0 1 0 4000 [system]: gpio l 8 0 4000 0 1 4000 [system]: switch reg w 7d00 77777;switch reg w 7d04 77777 [system]: gpio l 11 0 4000 0 1 4000 [system]: gpio l 9 0 4000 0 1 4000 [system]: gpio l 5 0 4000 0 1 4000 set_action: 291: set_action 0 Send DISASSOC frame(3) with ra0 Send DISASSOC frame(3) with ra1 Send DISASSOC frame(3) with ra4 Send DISASSOC frame(3) with ra5 [PMF]BndStrg_handle_onoff_event: MacTableDeleteEntry ee:44:6e:c8:20:de Send DISASSOC frame(3) with ra0 Send DISASSOC frame(3) with ra1 Send DISASSOC frame(3) with ra0 Send DISASSOC frame(3) with ra1 Send DISASSOC frame(3) with ra4 Send DISASSOC frame(3) with ra5 br0: port 5(ra0) entered forwarding state br0: port 6(rax0) entered forwarding state br0: port 7(rai0) entered forwarding state AUTH-true [DLINK_VENDOR_CHECK] STA associated. [DLINK_VENDOR_CHECK] STA authorized. AP SETKEYS DONE - AKMMap=WPA2PSK, PairwiseCipher=AES, GroupCipher=TKIP, wcid=1 from EE:44:6E:C8:20:DE PTK:16225f5122ef0d6f39ca9cc9fc90167df1295c6e2f703710b4feb6b60df65b352c7360e9cb6207f7c4601a371d63268b4e486698b7eb3dc5f36bb10fed9c35aa pSsid=hoffman RRM_EnqueueNeighborRep() : send Neighbor RSP Rcv Wcid(1) AddBAReq Start Seq = 00000002 br0Ip = c0a80101, brNetmask = ffffff00 dir3060 login: root Password: Login incorrect dir3060 login: admin Password: Login incorrect dir3060 login: root Password: Login incorrect Please press Enter to activate this console. dir3060 login: Login timed ouPlease press Enter to activate this console. dir3060 login: dir3060 login:


TIMEOUT_COUNT=10,Load address: 0x88000000 Loading: Got ARP REPLY, set server/gtwy eth addr (f4:6d:04:49:b3:21) Got it ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################### done Bytes transferred = 6583917 (64766d hex) LoadAddr=88000000 NetBootFileXferSize= 0064766d ..Erasing NAND Flash... ranand_erase: start:80000, len:20000 .Writing to NAND Flash... done Automatic boot of image at addr 0x88000000 ... ## Booting image at 88000000 ... Image Name: MIPS OpenWrt Linux-5.10.90 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 6583757 Bytes = 6.3 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... [ 0.000000] Linux version 5.10.90 (lucky@6700K) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r18589-e821849c4f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Jan 15 22:05:55 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is D-Link DIR-3060 A1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30096 r8192 d23152 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00054320 [ 0.000000] Readback ErrCtl register=00054320 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 245460K/262144K available (6664K kernel code, 621K rwdata, 1352K rodata, 4980K init, 235K bss, 16684K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x3cc/0x5e4 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015859] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033724] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106051] pid_max: default: 32768 minimum: 301 [ 0.115365] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129769] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.147759] rcu: Hierarchical SRCU implementation. [ 0.157524] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.173012] smp: Bringing up secondary CPUs ... [ 0.182577] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.182588] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.182599] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.182720] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.242931] Synchronize counters for CPU 1: done. [ 0.304917] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.304927] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.304934] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.304981] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.363880] Synchronize counters for CPU 2: done. [ 0.424072] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.424081] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.424089] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.424141] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.483443] Synchronize counters for CPU 3: done. [ 0.543044] smp: Brought up 1 node, 4 CPUs [ 0.555291] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.574796] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.588612] pinctrl core: initialized pinctrl subsystem [ 0.600742] NET: Registered protocol family 16 [ 0.611768] cpuidle: using governor teo [ 0.639882] random: fast init done [ 0.660119] clocksource: Switched to clocksource GIC [ 0.671803] NET: Registered protocol family 2 [ 0.680708] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.695828] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.712398] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.727546] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.741723] TCP: Hash tables configured (established 2048 bind 2048) [ 0.754451] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.767334] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.781369] NET: Registered protocol family 1 [ 0.789905] PCI: CLS 0 bytes, default 32 [ 5.378969] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 5.395715] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.407251] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 5.428990] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 5.440371] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 5.451648] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 5.463507] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 5.477571] printk: console [ttyS0] disabled [ 5.486080] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 5.504021] printk: console [ttyS0] enabled [ 5.504021] printk: console [ttyS0] enabled [ 5.520533] printk: bootconsole [early0] disabled [ 5.520533] printk: bootconsole [early0] disabled [ 5.541457] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 5.556285] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1 [ 5.568944] nand: Winbond W29N01HV [ 5.575721] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.590801] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 5.603830] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 5.618386] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 5.632952] Scanning device for bad blocks [ 6.286261] 9 fixed-partitions partitions found on MTD device mt7621-nand [ 6.299789] Creating 9 MTD partitions on "mt7621-nand": [ 6.310206] 0x000000000000-0x000000080000 : "Bootloader" [ 6.321746] 0x000000080000-0x000000100000 : "config" [ 6.332558] 0x000000100000-0x000000140000 : "factory" [ 6.343593] 0x000000140000-0x000000180000 : "config2" [ 6.354558] 0x000000180000-0x000002980000 : "firmware" [ 6.598096] 0x000002980000-0x000004980000 : "private" [ 6.609208] 0x000004980000-0x000007180000 : "firmware2" [ 6.620705] 0x000007180000-0x000007780000 : "mydlink" [ 6.631721] 0x000007780000-0x000008000000 : "reserved" [ 6.649844] libphy: Fixed MDIO Bus: probed [ 6.691357] libphy: mdio: probed [ 6.698582] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.714746] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 6.733083] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 6.746547] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 6.764151] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 6.780532] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 6.797010] mt7621-pci 1e140000.pcie: Parsing DT failed [ 6.809582] NET: Registered protocol family 10 [ 6.819831] Segment Routing with IPv6 [ 6.827262] NET: Registered protocol family 17 [ 6.836529] 8021q: 802.1Q VLAN Support v1.8 [ 6.848132] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.954758] libphy: dsa slave smi: probed [ 6.963184] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) [ 6.983255] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) [ 7.003336] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) [ 7.023382] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) [ 7.043486] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) [ 7.064296] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 7.081312] DSA: tree 0 setup [ 7.087586] rt2880-pinmux pinctrl: pcie is already enabled [ 7.098717] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 7.112089] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 7.129616] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 7.145918] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 7.162315] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 7.177454] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 7.192508] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 7.307155] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 7.318272] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 7.429553] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 7.443427] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 7.453139] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 7.462860] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 7.481584] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 7.494268] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 7.507971] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 7.521673] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.532601] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 7.552913] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 7.564893] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 7.577378] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff] [ 7.589923] pci 0000:00:00.0: supports D1 [ 7.597909] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 7.610226] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 7.622222] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 7.634709] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff] [ 7.647249] pci 0000:00:01.0: supports D1 [ 7.655233] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 7.668713] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 7.680758] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.694804] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 7.707449] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 7.738856] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 7.749294] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 7.761435] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 7.774960] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.788399] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 7.800425] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.814467] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 7.827114] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 7.858544] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 7.868980] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 7.881121] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 7.894645] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 7.907866] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 7.921043] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.934908] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 7.948077] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.961947] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 7.975467] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 7.988988] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 8.002517] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] [ 8.016039] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 8.029559] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 8.043092] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 8.057663] pci 0000:00:00.0: PCI bridge to [bus 01] [ 8.067552] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 8.081074] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 8.094601] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] [ 8.109164] pci 0000:00:01.0: PCI bridge to [bus 02] [ 8.119051] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 8.132573] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 8.166021] Freeing unused kernel memory: 4980K [ 8.175083] This architecture does not have kernel memory protection. [ 8.187921] Run /init as init process [ 8.195854] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 8.692216] init: Console is alive [ 8.699322] init: - watchdog - [ 8.720535] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.744961] usbcore: registered new interface driver usbfs [ 8.756093] usbcore: registered new interface driver hub [ 8.766876] usbcore: registered new device driver usb [ 8.787510] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 8.802596] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 8.817954] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.828594] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 8.850265] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 8.868538] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 8.881110] hub 1-0:1.0: USB hub found [ 8.888683] hub 1-0:1.0: 2 ports detected [ 8.897323] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.907990] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 8.922933] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 8.935783] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.952722] hub 2-0:1.0: USB hub found [ 8.960406] hub 2-0:1.0: 1 port detected [ 8.976750] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 9.000539] init: - preinit - /bin/board_detect: /etc/board.d/01_leds: line 35: syntax error: unexpected ")" (expecting ";;") [ 9.286825] random: jshn: uninitialized urandom read (4 bytes read) [ 9.337675] random: jshn: uninitialized urandom read (4 bytes read) [ 9.373407] random: jshn: uninitialized urandom read (4 bytes read) [ 9.563829] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 9.580424] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 9.580534] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 9.610862] 8021q: adding VLAN 0 to HW filter on device lan1 [ 9.624783] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.785482] procd: - early - [ 13.791505] procd: - watchdog - [ 14.360331] procd: - watchdog - [ 14.367045] procd: - ubus - [ 14.379637] urandom_read: 5 callbacks suppressed [ 14.379650] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.430864] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.447052] procd: - init - Please press Enter to activate this console. [ 14.805225] kmodloader: loading kernel modules from /etc/modules.d/* [ 15.021980] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb [ 15.025024] urngd: v1.0.2 started. [ 15.036940] Backport generated by backports.git v5.15.8-1-0-g83f664bb [ 15.078056] xt_time: kernel timezone is -0000 [ 15.141913] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 15.152721] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 15.163997] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 15.199460] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 15.210379] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 15.221749] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 15.234133] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 15.234133] [ 15.263365] random: crng init done [ 15.270478] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 15.270478] [ 15.289933] PPP generic driver version 2.4.2 [ 15.294144] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 15.302193] NET: Registered protocol family 24 [ 15.315864] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 15.349699] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 15.355794] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.367214] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 44.436145] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 44.457238] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 44.473269] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 44.476784] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 44.503842] 8021q: adding VLAN 0 to HW filter on device lan1 [ 44.517874] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 44.532207] br-lan: port 1(lan1) entered blocking state [ 44.542688] br-lan: port 1(lan1) entered disabled state [ 44.554129] device lan1 entered promiscuous mode [ 44.563452] device eth0 entered promiscuous mode [ 44.600757] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 44.614880] 8021q: adding VLAN 0 to HW filter on device lan2 [ 44.629759] br-lan: port 2(lan2) entered blocking state [ 44.640654] br-lan: port 2(lan2) entered disabled state [ 44.652039] device lan2 entered promiscuous mode [ 44.674291] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 44.688060] 8021q: adding VLAN 0 to HW filter on device lan3 [ 44.702681] br-lan: port 3(lan3) entered blocking state [ 44.713193] br-lan: port 3(lan3) entered disabled state [ 44.724835] device lan3 entered promiscuous mode [ 44.748758] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 44.762624] 8021q: adding VLAN 0 to HW filter on device lan4 [ 44.777636] br-lan: port 4(lan4) entered blocking state [ 44.788556] br-lan: port 4(lan4) entered disabled state [ 44.800408] device lan4 entered promiscuous mode [ 44.825702] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 44.839372] 8021q: adding VLAN 0 to HW filter on device wan [ 49.731181] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 49.746239] br-lan: port 1(lan1) entered blocking state [ 49.756762] br-lan: port 1(lan1) entered forwarding state [ 49.771372] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.35.0 (2022-01-15 22:05:55 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r18589-e821849c4f ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. --------------------------------------------------


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1