D-Link DHP-1565

[ 0.000000] Linux version 3.10.36 (jacek@HP) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40509) ) #1 Thu Apr 24 15:03:17 CEST 2014 [ 0.000000] MyLoader: sysp=68e6beb0, boardp=2778aa28, parts=f465ba30 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 1 [ 0.000000] Clocks: CPU:560.000MHz, DDR:480.000MHz, AHB:240.000MHz, Ref:40.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 8030a9b0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=DHP-1565-A1 console=ttyS0,115200 mtdparts=spi0.0:64k(uboot)ro,64k(nvram)ro,15936k(firmware),192k(lang)ro,64k(mac)ro,64k(art)ro rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 126248k/131072k available (2218k kernel code, 4824k reserved, 599k data, 252k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.060000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] NET: Registered protocol family 16 [ 0.080000] MIPS: machine is D-Link DHP-1565 rev. A1 [ 0.300000] bio: create slab <bio-0> at 0 [ 0.300000] Switching to clocksource MIPS [ 0.310000] NET: Registered protocol family 2 [ 0.310000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.320000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.330000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.330000] TCP: reno registered [ 0.330000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.340000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.350000] NET: Registered protocol family 1 [ 0.350000] PCI: CLS 0 bytes, default 32 [ 0.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.370000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.380000] msgmni has been set to 246 [ 0.380000] io scheduler noop registered [ 0.390000] io scheduler deadline registered (default) [ 0.390000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.420000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.430000] console [ttyS0] enabled, bootconsole disabled [ 0.440000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.450000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.450000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.460000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.460000] Creating 6 MTD partitions on "spi0.0": [ 0.470000] 0x000000000000-0x000000010000 : "uboot" [ 0.480000] 0x000000010000-0x000000020000 : "nvram" [ 0.480000] 0x000000020000-0x000000fb0000 : "firmware" [ 0.500000] 2 uimage-fw partitions found on MTD device firmware [ 0.510000] 0x000000020000-0x00000011c9ea : "kernel" [ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.530000] 0x00000011c9ea-0x000000fb0000 : "rootfs" [ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.540000] mtd: device 4 (rootfs) set to be root filesystem [ 0.550000] 1 squashfs-split partitions found on MTD device rootfs [ 0.560000] 0x000000340000-0x000000fb0000 : "rootfs_data" [ 0.560000] 0x000000fb0000-0x000000fe0000 : "lang" [ 0.570000] 0x000000fe0000-0x000000ff0000 : "mac" [ 0.580000] 0x000000ff0000-0x000001000000 : "art" [ 0.610000] switch0: Atheros AR8327 rev. 2 switch registered on ag71xx-mdio.0 [ 1.800000] libphy: ag71xx_mdio: probed [ 2.360000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 2.370000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.380000] TCP: cubic registered [ 2.380000] NET: Registered protocol family 17 [ 2.380000] 8021q: 802.1Q VLAN Support v1.8 [ 2.390000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.400000] Freeing unused kernel memory: 252K (80321000 - 80360000) [ 5.160000] usbcore: registered new interface driver usbfs [ 5.160000] usbcore: registered new interface driver hub [ 5.170000] usbcore: registered new device driver usb [ 5.180000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.190000] ehci-platform: EHCI generic platform driver [ 5.190000] ehci-platform ehci-platform: EHCI Host Controller [ 5.200000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.210000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.230000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.230000] hub 1-0:1.0: USB hub found [ 5.240000] hub 1-0:1.0: 1 port detected [ 5.240000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.430000] eth0: link up (1000Mbps/Full duplex) [ 6.950000] jffs2: notice: (332) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 19 of xref (0 dead, 3 orphan) found. [ 6.980000] eth0: link down [ 9.070000] NET: Registered protocol family 10 [ 9.080000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max) [ 9.090000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.110000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2 [ 9.120000] Backport generated by backports.git backports-20140221-0-g8e94650 [ 9.130000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.170000] xt_time: kernel timezone is -0000 [ 9.200000] cfg80211: Calling CRDA to update world regulatory domain [ 9.200000] cfg80211: World regulatory domain updated: [ 9.210000] cfg80211: DFS Master region: unset [ 9.210000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 9.220000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.230000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.240000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 9.250000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 9.250000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 9.260000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 9.300000] PPP generic driver version 2.4.2 [ 9.320000] NET: Registered protocol family 24 [ 9.370000] ath: EEPROM regdomain: 0x0 [ 9.370000] ath: EEPROM indicates default country code should be used [ 9.370000] ath: doing EEPROM country->regdmn map search [ 9.370000] ath: country maps to regdmn code: 0x3a [ 9.370000] ath: Country alpha2 being used: US [ 9.370000] ath: Regpair used: 0x3a [ 9.380000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 9.400000] cfg80211: Calling CRDA for country: US [ 9.400000] cfg80211: Regulatory domain changed to country: US [ 9.410000] cfg80211: DFS Master region: FCC [ 9.410000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 9.420000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 9.430000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A) [ 9.440000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s) [ 9.450000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 9.460000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 9.470000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47 [ 16.830000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.830000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 16.840000] device eth0.1 entered promiscuous mode [ 16.850000] device eth0 entered promiscuous mode [ 16.860000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 16.870000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 18.690000] eth0: link up (1000Mbps/Full duplex) [ 18.700000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 18.710000] br-lan: port 1(eth0.1) entered forwarding state [ 18.710000] br-lan: port 1(eth0.1) entered forwarding state [ 18.720000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 18.720000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 18.730000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 19.240000] IPv6: eth0.2: IPv6 duplicate address fe80::ceb2:55ff:feca:4ade detected! [ 20.710000] br-lan: port 1(eth0.1) entered forwarding state