Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:d-link:d-link_dap-2680_a1 [2021/01/24 18:44] – [Debricking] s_2toh:d-link:d-link_dap-2680_a1 [2021/01/24 18:53] – [Buttons] s_2
Line 62: Line 62:
  
  
--> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]] +-> Please see the main article for the DAP-2xxx series for [[:toh:d-link:D-Link DAP Series of Business Access Points#flashing]] instructions.
- +
-FIXME Please add the installation procedure here.+
  
 ==== Flash Layout ==== ==== Flash Layout ====
-<WRAP BOX> +^ start ^ size ^ label ^ 
-FIXME //[[:docs:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[docs:techref:flash.layout#partitioning_of_the_flash|example]]).// +0x00000000 | 0x00040000 (256k) bootloader | 
- +| 0x00040000 | 0x00010000 (64k| bdcfg | 
-Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout. +| 0x00050000 | 0x00010000 (64k) | rgdb | 
-</WRAP> +0x00060000 | 0x00010000 (64k) | unknown | 
 +| 0x00070000 | 0x00ee0000 (15232k) | upgrade | 
 +| 0x00f50000 | 0x00020000 (128k) | langpack | 
 +| 0x00f70000 | 0x00070000 (448k) | captival | 
 +| 0x00fe0000 | 0x00010000 (64k) | certificate | 
 +| 0x00ff0000 | 0x00010000 (64k) | radiocfg |
 ==== OEM easy installation ==== ==== OEM easy installation ====
  
Line 90: Line 92:
 </WRAP> </WRAP>
  
-==== OEM installation using the TFTP method ==== 
- 
-->  [[docs:guide-user:installation:generic.flashing.tftp]] 
- 
-=== Specific values needed for tftp === 
- 
-<WRAP BOX> 
- 
-FIXME Enter values for "FILL-IN" below 
- 
-^ Bootloader tftp server IPv4 address  | FILL-IN   | 
-^ Bootloader MAC address (special)     | FILL-IN   | 
-^ Firmware tftp image                  | [[:downloads|Latest OpenWrt release]] (**''NOTE:''** Name must contain //"tftp"//) | 
-^ TFTP transfer window                 | FILL-IN seconds                                | 
-^ TFTP window start                    | approximately FILL-IN seconds after power on   | 
-^ TFTP client required IP address      | FILL-IN                                        | 
- 
-</WRAP> 
  
 ===== Upgrading OpenWrt ===== ===== Upgrading OpenWrt =====
Line 165: Line 149:
 Set up your Internet connection, configure wireless, configure USB port, etc. Set up your Internet connection, configure wireless, configure USB port, etc.
  
-===== Specific Configuration ===== 
  
-<WRAP BOX> 
-FIXME Please fill in real values for this device, then remove the EXAMPLEs 
  
-==== Network interfaces ==== 
-The default network configuration is: 
-^ Interface Name   ^ Description                  ^ Default configuration    ^ 
-| br-lan           | EXAMPLE LAN & WiFi           | EXAMPLE 192.168.1.1/24   | 
-| vlan0 (eth0.0)   | EXAMPLE LAN ports (1 to 4)   | EXAMPLE None             | 
-| vlan1 (eth0.1)   | EXAMPLE WAN port             | EXAMPLE DHCP             | 
-| wl0              | EXAMPLE WiFi                 | EXAMPLE Disabled         | 
  
-</WRAP>+==== Buttons ====
  
-==== Switch Ports (for VLANs) ==== +The D-Link DAP-2680 has the following buttons:
-<WRAP BOX> +
-FIXME Please fill in real values for this device, then remove the EXAMPLEs+
  
-Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. +BUTTON GPIO 
-Port             Switch port   +Reset   18  |
-Internet (WAN)   | EXAMPLE 4     | +
-| LAN 1            | EXAMPLE 3     | +
-| LAN 2            | EXAMPLE 2     | +
-| LAN 3            | EXAMPLE 1     | +
-| LAN 4            EXAMPLE 0     |+
  
-</WRAP> 
- 
-==== Buttons ==== 
 -> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s). -> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s).
-Here, we merely name the buttons, so we can use them in the above Howto. 
  
-<WRAP BOX> 
-FIXME Please fill in real values for this device, then remove the EXAMPLEs 
  
-The D-Link DAP-2680 has the following buttons:+==== LEDs ====
  
-BUTTON                       Event   +LED GPIO 
-EXAMPLE Reset                |  reset  | +power green  |  19  | 
-EXAMPLE Secure Easy Setup      ses   | +power red   20  |
-| EXAMPLE No buttons at all.      -    | +
- +
-</WRAP>+
  
 ===== Hardware ===== ===== Hardware =====
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1