Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:d-link:d-link_dap-2680_a1 [2021/01/24 18:43] – [OEM bootlog] s_2 | toh:d-link:d-link_dap-2680_a1 [2021/01/24 18:53] – [Buttons] s_2 | ||
|---|---|---|---|
| Line 62: | Line 62: | ||
| - | -> [[docs:guide-user:installation: | + | -> Please see the main article for the DAP-2xxx series for [[:toh:d-link:D-Link DAP Series of Business Access Points#flashing]] |
| - | + | ||
| - | FIXME Please add the installation procedure here. | + | |
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | <WRAP BOX> | + | ^ start ^ size ^ label ^ |
| - | FIXME // | + | | 0x00000000 | 0x00040000 |
| - | + | | 0x00040000 | 0x00010000 (64k) | bdcfg | | |
| - | Please check out the article [[docs: | + | | 0x00050000 | 0x00010000 (64k) | rgdb | |
| - | </ | + | | 0x00060000 | 0x00010000 (64k) | unknown | |
| + | | 0x00070000 | 0x00ee0000 (15232k) | upgrade | | ||
| + | | 0x00f50000 | 0x00020000 (128k) | langpack | | ||
| + | | 0x00f70000 | 0x00070000 (448k) | captival | | ||
| + | | 0x00fe0000 | 0x00010000 (64k) | certificate | | ||
| + | | 0x00ff0000 | 0x00010000 (64k) | radiocfg | | ||
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| Line 90: | Line 92: | ||
| </ | </ | ||
| - | ==== OEM installation using the TFTP method ==== | ||
| - | |||
| - | -> [[docs: | ||
| - | |||
| - | === Specific values needed for tftp === | ||
| - | |||
| - | <WRAP BOX> | ||
| - | |||
| - | FIXME Enter values for " | ||
| - | |||
| - | ^ Bootloader tftp server IPv4 address | ||
| - | ^ Bootloader MAC address (special) | ||
| - | ^ Firmware tftp image | [[: | ||
| - | ^ TFTP transfer window | ||
| - | ^ TFTP window start | approximately FILL-IN seconds after power on | | ||
| - | ^ TFTP client required IP address | ||
| - | |||
| - | </ | ||
| ===== Upgrading OpenWrt ===== | ===== Upgrading OpenWrt ===== | ||
| Line 157: | Line 141: | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[docs:guide-user:troubleshooting: | + | -> Please see the main article for the DAP-2xxx series for [[:toh:d-link:D-Link DAP Series of Business Access Points# |
| ===== Failsafe mode ===== | ===== Failsafe mode ===== | ||
| -> [[docs: | -> [[docs: | ||
| Line 166: | Line 149: | ||
| Set up your Internet connection, configure wireless, configure USB port, etc. | Set up your Internet connection, configure wireless, configure USB port, etc. | ||
| - | ===== Specific Configuration ===== | ||
| - | <WRAP BOX> | ||
| - | FIXME Please fill in real values for this device, then remove the EXAMPLEs | ||
| - | ==== Network interfaces ==== | ||
| - | The default network configuration is: | ||
| - | ^ Interface Name ^ Description | ||
| - | | br-lan | ||
| - | | vlan0 (eth0.0) | ||
| - | | vlan1 (eth0.1) | ||
| - | | wl0 | EXAMPLE WiFi | EXAMPLE Disabled | ||
| - | </ | + | ==== Buttons ==== |
| - | ==== Switch Ports (for VLANs) ==== | + | The D-Link DAP-2680 has the following buttons: |
| - | <WRAP BOX> | + | |
| - | FIXME Please fill in real values for this device, then remove | + | |
| - | Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. | + | ^ BUTTON |
| - | ^ Port ^ Switch port ^ | + | | Reset |
| - | | Internet (WAN) | EXAMPLE 4 | | + | |
| - | | LAN 1 | EXAMPLE 3 | | + | |
| - | | LAN 2 | EXAMPLE 2 | | + | |
| - | | LAN 3 | EXAMPLE 1 | | + | |
| - | | LAN 4 | + | |
| - | </ | ||
| - | |||
| - | ==== Buttons ==== | ||
| -> [[docs: | -> [[docs: | ||
| - | Here, we merely name the buttons, so we can use them in the above Howto. | ||
| - | <WRAP BOX> | ||
| - | FIXME Please fill in real values for this device, then remove the EXAMPLEs | ||
| - | The D-Link DAP-2680 has the following buttons: | + | ==== LEDs ==== |
| - | ^ BUTTON | + | ^ LED ^ GPIO ^ |
| - | | EXAMPLE Reset | + | | power green |
| - | | EXAMPLE Secure Easy Setup | + | | power red |
| - | | EXAMPLE No buttons at all. | + | |
| - | + | ||
| - | </ | + | |
| ===== Hardware ===== | ===== Hardware ===== | ||