D-Link DAP-2660

The DAP-2660 is an AC1200 Wall-Mount PoE Access Point from the D-Link DAP Series of Business Access Points, manufactured by Alpha Networks.

Generic Router

Supported

CPU Ram Flash Network WLAN USB Serial JTag
Qualcomm Atheros QCA9557 @ 720 MHz 128 MiB 16 MiB 1x 100/1000 2×2 bgn + 2×2 ac No Yes ?

Factory Web UI is at 192.168.0.50, login with 'admin' and blank password, flash factory.bin.

After flashing factory.bin, additional free space can be reclaimed by flashing sysupgrade.bin, since the factory image requires some padding to be accepted for upgrading via OEM Web UI.

generic.debrick

Recovery Web UI is at 192.168.0.50, connect network cable, hold reset button during power-on and keep it pressed until uploading has started (only required when checksum is ok, e.g. for reverting back to oem firmware), flash factory.bin

The D-Link DAP-2660 has the following buttons:

BUTTON GPIO
Reset 17
LED GPIO
power green 23
power red 14
start size label
0x00000000 0x00040000 (256k) bootloader
0x00040000 0x00010000 (64k) bdcfg
0x00050000 0x00010000 (64k) rgdb
0x00060000 0x00010000 (64k) unknown
0x00070000 0x00ee0000 (15232k) firmware
0x00f50000 0x00020000 (128k) langpack
0x00f70000 0x00070000 (448k) captival
0x00fe0000 0x00010000 (64k) certificate
0x00ff0000 0x00010000 (64k) art

dap-2660_pcb.jpg

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

→ Please see the main article for the DAP-2xxx series for serial_console.

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

U-Boot 1.1.4 (Jan 26 2014 - 16:16:52) ap135 - Scorpion 1.0 ALPHA U-boot v1.00rc002 DRAM: sri Scorpion 1.0 ath_ddr_initial_config(178): (32bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x2, 0x1d) Tap values = (0xf, 0xf, 0xf, 0xf) 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 243k for U-Boot at: 87fc0000 Reserving 192k for malloc() at: 87f90000 Reserving 44 Bytes for Board Info at: 87f8ffd4 Reserving 36 Bytes for Global Data at: 87f8ffb0 Reserving 128k for boot params() at: 87f6ffb0 Stack Pointer at: 87f6ff98 Now running in RAM - U-Boot at: 87fc0000 Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18 flash size 16MB, sector count = 256 Flash: 16 MB *** Warning - bad CRC, using default environment *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... athrs_sgmii_res_cal: cal value = 0xe ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->f1e PHY* : cfg1 0x80000000 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 4, Neg Success ATHRSF1_PHY: unit 0 phy addr 4 eth0 up eth0 Setting 0x18116290 to 0x60c0214f press 'q' to stop autoboot: 0 ## Booting image at 9f070000 ... Image Name: 7zip Linux Kernel Created: 1970-01-01 0:00:00 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: -1 Bytes = 4096 MB Load Address: 80002000 Entry Point: 80002000 Uncompressing Kernel Image with LZMA ... Check Image ... Image OK! OK No initrd ## Transferring control to Linux (at address 80002000) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... Booting QCA955x Linux version 2.6.31--LSDK-10.2.85 (release@cdWSCMPL06) (gcc version 4.3.3 (GCC) ) #1 Fri Jul 29 13:44:49 CST 2016 flash_size passed from bootloader = 16 CPU revision is: 00019750 (MIPS 74Kc) cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock0 rw mem=128m PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 112512k/131072k available (2171k kernel code, 18376k reserved, 478k data, 144k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 359.42 BogoMIPS (lpj=718848) Mount-cache hash table entries: 512 ****************ALLOC*********************** Packet mem: 802ce6c0 (0xe00000 bytes) ******************************************** NET: Registered protocol family 16 ath_pcibios_init: bus 0 ath_pcibios_init(232): PCI 0 CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 pcibios_map_irq: IRQ 75 for bus 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 220 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled brd: module loaded ELBOX CFI physmap flash device: 1000000 at 9f000000 ATH serial flash !! ath-nor0: squashfs filesystem found at offset 0x00160000 Creating 11 MTD partitions on "ath-nor0": 0x0000001600c0-0x000000a420c0 : "rootfs" 0x000000070000-0x000000f50000 : "upgrade" 0x000000050000-0x000000060000 : "rgdb" 0x000000040000-0x000000050000 : "bdcfg" 0x000000f50000-0x000000f70000 : "langpack" 0x000000fe0000-0x000000ff0000 : "certificate" 0x000000ff0000-0x000001000000 : "radiocfg" 0x000000000000-0x000001000000 : "flash" 0x000000000000-0x000000040000 : "bootloader" 0x000000040000-0x000000050000 : "boot config" 0x000000f70000-0x000000fe0000 : "captival" u32 classifier Actions configured arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> athwdt_init: Registering WDT success ath_otp_init: Registering OTP success VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 144k freed init started: BusyBox v1.14.1 (2016-07-29 13:44:57 CST) starting pid 133, tty '': '/etc/init.d/rcS' [/etc/init.d/S03config.sh] Mounting proc and var ... SymbLink /dev/mtdblock/0 SymbLink /dev/mtdblock/1 SymbLink /dev/mtdblock/10 SymbLink /dev/mtdblock/2 SymbLink /dev/mtdblock/3 SymbLink /dev/mtdblock/4 SymbLink /dev/mtdblock/5 SymbLink /dev/mtdblock/6 SymbLink /dev/mtdblock/7 SymbLink /dev/mtdblock/8 SymbLink /dev/mtdblock/9 Inserting modules ... Inserting Rebootm ... Rebootm loading ... Inserting atheros ethernet ... qca955x_GMAC: Length per segment 1536 955x_GMAC: qca955x_gmac_attach 955x_GMAC: qca955x_set_gmac_caps Currently in polling mode unit0 mac0 registering f1e ..... qca955x_GMAC: RX TASKLET - Pkts per Intr:160 qca955x_GMAC: Mac address for unit 0:bfff0000 qca955x_GMAC: ff:ff:ff:ff:ff:ff qca955x_GMAC: Max segments per packet : 1 qca955x_GMAC: Max tx descriptor count : 128 qca955x_GMAC: Max rx descriptor count : 224 qca955x_GMAC: Mac capability flags : 2200 Inserting gpio ... GPIO driver initialized. done. Inserting watchdog ... External watchdog loading ... Enable external watch dog with gpio 20 clear Start xmldb ... [/etc/scripts/misc/profile.sh] getnew ... [/etc/scripts/misc/defnodes.sh] ... [/etc/defnodes/S10setext.sh] ... PHP [/etc/defnodes/S11setnodes.php] ... PHP [/etc/defnodes/S12features.php] ... PHP [/etc/defnodes/S13flashspeed.php] ... PHP [/etc/defnodes/S20setnodes.php] ... mount: mounting /dev/mtdblock/4 on /www/locale/alt failed: Invalid argument PHP [/etc/defnodes/S40brand.php] ... [/etc/scripts/misc/defnodes.sh] Done !! [/etc/templates/timezone.sh] ... [/etc/templates/logs.sh] ... [/var/run/logs_run.sh] ... gpio set led status [/etc/templates/powerled.sh] ... [/var/run/powerled_run.sh] ... athr_gmac_ring_alloc Allocated 2048 at 0x879e5800 sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000 athr_gmac_ring_alloc Allocated 3584 at 0x879bf000 sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600 955x_GMAC: eth0 in RGMII MODE Scorpion -----> 8035 PHY Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 4, Neg Success ATHRSF1_PHY: unit 0 phy addr 4 955x_GMAC: Enet Unit:0 PHY:0 is UP eth0 RGMII 100Mbps full duplex 955x_GMAC: qca955x_soc_gmac_set_mac_duplex 955x_GMAC: qca955x_soc_gmac_set_link Done 955x_GMAC: done cfg2 0x7115 ifctl 0x10000 miictrl 955x_GMAC: eth0 in RGMII MODE Scorpion -----> 8035 PHY Setting Drop CRC Errors, Pause Frames and Length Error frames 955x_GMAC: qca955x_soc_gmac_set_mac_duplex 955x_GMAC: qca955x_soc_gmac_set_link Done **************************lpbk test pass ************************** 955x_GMAC: unit 0: phy 0 not up carrier 1 [/etc/init.d/S03config.sh] done! [/etc/init.d/S10system.sh] Write some proc file ... Enable panic timeout when Kernel panic ... start Layout ... [/etc/scripts/layout.sh] start ... [/var/run/layout_start.sh] ... Start bridge layout ... device eth0 entered promiscuous mode start LAN ... [/etc/templates/lan.sh] ... [/var/run/lan_start.sh] ... Bridge mode selected, LAN is disabled ! start web server ... [/etc/templates/webs.sh] start ... [/var/run/webs_start.sh] ... Starting HTTPD ... nvram: not found nvram: not found start eth0 vlan setup ... [/etc/scripts/eth_vlan.sh] start ... [/var/run/eth0_vlan_start.sh] ... disable VLAN #!/bin/sh limitedadmin.sh... [/etc/scripts/eth_vlan.sh] start ... [/var/run/eth0_vlan_stop.sh] ... [/var/run/eth0_vlan_start.sh] ... disable VLAN #!/bin/sh pingctl.sh... start fresetd ... rxcheck: not found enable LAN ports ... Factory reset time : 5 secs System reset time : 1 secs WPS command : [/etc/templates/wps.sh pbc &] [/etc/scripts/enlan.sh] ... Generate channel table according to the country code... generate country domain mapping table Generate VLAN table according to the port... start WAN ... Set WAN port media type 0 slinktype: not found [/etc/templates/wan.sh] start ... [/var/run/eth0_vlan_start.sh] ... disable VLAN [/var/run/wan_start.sh] ... Bridge mode selected ! Start WAN(br0),192.168.178.20/255.255.255.0 ... [/etc/templates/wanup.sh] ... [/var/run/wan_up.sh] ... [/etc/templates/ntp.sh] ... killall: ntpclient: no process killed NTP client is disabled ... [/etc/templates/upnpd.sh] ... [/var/run/upnpd_start.sh] ... UPNP function is not enabled !! /etc/templates/webredirect.sh: not found [/usr/sbin/submit] CAPTIVAL_PORTAL ... [/var/run/captival_portal_stop.sh] ... captival portal already stop [/var/run/captival_portal_start.sh] ... captival_state 0 captival portal is disable >>>/var/run/wan_start.sh: Start IPv6 configuration >>> Disable IPv6. <<< End of IPv6 <<< captival_tar prep ... remains :457216bytes nvram: not found nvram: not found start stunnel ... [/etc/templates/stunnel.sh] ... Setting certificate. [/var/run/stunnel_start.sh] ... Starting universal SSL tunnel: stunnel. Enable wlan restart ... start WLAN ... wlanRestart: not found [/etc/templates/wlan.sh] ... SERVD: stop service [WLAN] SERVD: service [WLAN] is already stopped. SERVD: start service [WLAN] start telnet daemon ... [/etc/templates/wlan_run.sh] start ... Start telnetd ... nvram: not found nvram: not found start SSHD daemon ... [/etc/templates/sshd.sh] ... [/etc/templates/autorekey.sh] ... [/var/run/autorekey_start_a.sh] ... [/var/run/autorekey_start_g.sh] ... [/var/run/sshd_start.sh] ... start sshd ... Disable start-up daemon: sshd. start DHCP server [/etc/templates/dhcpd.sh] ... start WLAN ..... [/var/run/dhcpd_restart.sh] ... Stop DHCP server (br0) ... Start DHCP server (br0) ... DHCP server is disabled! start SNMP ... [/etc/templates/snmp.sh] ... [/var/run/snmp_start.sh] ... Start SNMP daemon ... start cwmHelper ... start NEAP ... [/etc/templates/certs/certscmd.sh] ... [/etc/templates/neaps.sh] start ... central wifi manager is not enable ,cwmHelper quit DEVCONF: unable to read config data (ret=-3) ! Getting External certificate for hostapd & wpa_supplicant. Fail! [/var/run/wlan_insmod.sh] ... [/var/run/neaps_start.sh] ... Start Neap Server ... adf: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint start NEAPC ... [/etc/templates/neapc.sh] start ... [/var/run/neapc_start.sh] ... Start NeapC Client ... Stop apneaps Server ... : not found start APNEAPS_V2 ... [/etc/templates/apneaps_v2.sh] start ... Stop apneaps_v2 Server ... start AUTORFC ... [/etc/templates/autorf.sh] start ... ############## snmp beacon oid init ############## ############## snmp init ############## Stop autorf client ... start LOADBALANCE ... [/etc/templates/loadbalance.sh] start ... [/var/run/loadbalance_start.sh] ... start Microsoft LLDP ... [/etc/templates/lld2d.sh] ... [/var/run/lld2d_start.sh] ... Start LLD2 daemon ... start Ethlink ... start Trap Monitor ... ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [/etc/templates/arpspoofing.sh] start ... ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [/var/run/arpspoofing_start.sh] ... Start arp spoofing prevention ... arp spoofing prevention is disabled. #!/bin/sh netfilter.sh... netfilter_flag: 0 start DHCP multicast to unicast ... #!/bin/sh ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved getaddrinfo: Name or service not known Creating directory: /var/net-snmp dhcp_mc2uc.sh... [/etc/init.d/S10system.sh] done! rcS done! Please press Enter to activate this console. NET-SNMP version 5.4.1 ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_ahb: 10.2-00082-4 (Atheros/multi-bss) __ath_attach: Set global_scn[0] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead *** ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=512 Bootstrap clock 40MHz Enterprise mode: 0x40000000 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6164] rx chainmask mismatch actual 3 sc_chainmak 0 ath_get_caps[6139] tx chainmask mismatch actual 3 sc_chainmak 0 ath_attach_dfs[12582] dfsdomain 1 wifi0: Atheros 955X: mem=0xb8100000, irq=2 ath_pci: 10.2-00082-4 (Atheros/multi-bss) ath_pci_probe PCI device id is 003c :003c ath_pci 0000:00:00.0: ath DEBUG: sc=0x87b13800 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt __ol_ath_attach: ath_attach TODO __ol_ath_attach: dev name wifi1 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 ol_ath_attach() BMI inited. ol_ath_attach() BMI Get Target Info. ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_ath_attach() configure Target . qc98xx_verify_checksum: flash checksum passed: 0x2b94 ol_transfer_bin_file 1891: Download Flash data len 2116 QCA98xx CtlData 5G override ol_transfer_bin_file 1836: Download Firmware data len 229496 ol_ath_attach() Download FW. ol_ath_attach() HT Create . ol_ath_attach() HIF Claim. ol_ath_attach() BMI Done. ol_ath_attach() WMI attached. wmi_handle 86590000 +HWT CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5 CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x556ee0 nbytes 0 recv_ctxt 0x8658b3a0 -HWT HTC Service:0x0300 ep:1 TX flow control disabled CE_pkt_dl_len_set CE 4 Pkt download length 64 ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 86740000 HTC Service:0x0100 ep:2 TX flow control disabled wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event num_rf_chain : 00000002 ht_cap_info: : 0000085b vht_cap_info : 338001b2 vht_supp_mcs : 0000fffa LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256 idx 0 req 1 num_units 0 num_unit_info 2 unit size 444 actual units 145 chunk 0 len 64380 requested ,ptr 0x6750000 FIRMWARE:P 145 V 16 T 443 FIRMWARE:_wlan_rtt_enable wmi_ready_event_rx: WMI UNIFIED READY event ol_ath_connect_htc() WMI is ready ol_ath_set_host_app_area TODO target uses HTT version 2.1; host uses 2.1 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 ol_regdmn_init_channels: isEIRP=0 Add VHT80 channel: 5210 Add VHT80 channel: 5775 Skipping VHT80 channel 5825 ol_ath_phyerr_attach: called OL Resmgr Init-ed Green-AP : Green-AP : Attached Green-AP : Attached ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=86739974, radar_info=87907bd0 ol_ath_rtt_meas_report_attach: called ol_ath_attach() UMAC attach . ol_if_dfs_configure: called ol_if_dfs_configure: FCC domain ol_if_dfs_disable: called ol_ath_attach: Calling ol_if_dfs_configure __ol_ath_attach: init tx/rx TODO __ol_ath_attach: hard_header_len reservation 58 Initializing Pktlogs for 11ac [/var/run/wlan_start.sh] ... ath_attach_dfs[12582] dfsdomain 1 wlan_vap_create : enter. devhandle=0x86550360, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x86550360, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created ath0 Start WLAN interface ath0 ... sc nodebug 0 Interface doesn't accept private ioctl... ForBiasAuto (8BE0): Operation not permitted ====essid: DES SSID SET=CyberNetA CyberNetA,len:9,Set freq vap stop send + 87bc4000 path:/var/run/atSet freq vap stop send -87bc4000 h0.ssid==== Set wait done --87bc4000 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [/var/run/wlan_start.sh] ... isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 ol_regdmn_init_channels: isEIRP=1 Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 ath_ioctl: SIOC80211IFCREATE CALLED ap vap with real mac wmi_unified_vdev_create_send: ID = 0 VAP Addr = 54:b8:0a:35:08:98: Setting dscp for vap id: 0 VAP device ath16 created ath16 Start WLAN interface ath16 ... ====essid: DES SSID SET=CyberNetX CyberNetX,len:9,Set freq vap stop send + 85e20000 path:/var/run/atOL vap_stop + h16.ssid==== wmi_unified_vdev_stop_send for vap 0 (86590000) OL vap_stop - STOPPED EVENT for vap 0 (86590000) Set freq vap stop send -85e20000 Set wait done --85e20000 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [/var/run/wlan_start.sh] ... sleep 2..... FWLOG: [41452] WHAL_SMARTANT_CONFIGURE ( 0x1, 0x8 ) FWLOG: [41452] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) FWLOG: [41452] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) FWLOG: [41452] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) FWLOG: [41452] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) FWLOG: [41458] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 ) FWLOG: [41458] WHAL_ERROR_RESET_PM ( ) FWLOG: [41581] WHAL_SMARTANT_CONFIGURE ( 0x0, 0x0 ) FWLOG: [42185] WHAL_SMARTANT_CONFIGURE ( 0x1, 0x0 ) [/var/run/wlan_device_up.sh] ... UP 2.4G interface ! device ath0 entered promiscuous mode ALPHA:[Wireless] 2.4G:Initiate Wireless success ALPHA:[SNMP-TRAP][Specific=7] br0: port 2(ath0) entering forwarding state ====essid: DES SSID SET=CyberNetA CyberNetA,len:9,path:/var/run/ath0.ssid==== Filter Accept CHLOAD Param Over RSSI ---Chan 6 cur 241 min 246 delta -5 allowed 10 Best Channel Selected 6 rssi 246 nf -107 UP 5G interface ! OL vap_stop + wmi_unified_vdev_stop_send for vap 0 (86590000) OL vap_stop - STOPPED EVENT for vap 0 (86590000) wmi_unified_scan_start_send for vap 0 (86590000) device ath16 entered promiscuous mode ALPHA:[Wireless] 5G:Initiate Wireless success ALPHA:[SNMP-TRAP][Specific=7] br0: port 3(ath16) entering forwarding state ====essid: DES SSID SET=CyberNetX CyberNetX,len:9,path:/var/run/ath16.ssid==== osif_vap_init: Timeout waiting for vap to stop...returning Filter Accept CHLOAD Param Over RSSI ---Chan 116 cur 18 min 18 delta 0 allowed 10 Filter Accept CHLOAD Param Over RSSI ---Chan 120 cur 22 min 18 delta 4 allowed 10 Filter Accept CHLOAD Param Over RSSI ---Chan 124 cur 26 min 18 delta 8 allowed 10 Filter Accept REGPOWER Param Over CH LOAD ---Chan 116 cur 2 min 0 delta 2 allowed 10 Filter Accept REGPOWER Param Over CH LOAD ---Chan 120 cur 1 min 0 delta 1 allowed 10 Filter Accept REGPOWER Param Over CH LOAD ---Chan 124 cur 0 min 0 delta 0 allowed 10 Filter Accept RSSI TOTOAL Param Over REG POWER ---Chan 116 cur 30 min 30 delta 0 allowed 0 Filter Accept RSSI TOTOAL Param Over REG POWER ---Chan 120 cur 30 min 30 delta 0 allowed 0 Filter Accept RSSI TOTOAL Param Over REG POWER ---Chan 124 cur 30 min 30 delta 0 allowed 0 OL vap_start + wmi_unified_vdev_start_send for vap 0 (86590000) OL vap_start - ol_vdev_start_resp_ev for vap 0 (86590000) ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: ol_if_dfs_configure: called ol_if_dfs_configure: ETSI domain ol_if_dfs_disable: called ol_if_dfs_enable: called cac_start chan 5580 timeout 612 sec, curr time: 4294712 sec Notification to UMAC VAP layer br0: port 3(ath16) multicast bandwidth all br0: port 2(ath0) multicast bandwidth all br0: port 1(eth0) multicast bandwidth all Start hostapd ... [/etc/templates/lld2d.sh] ... [/var/run/lld2d_stop.sh] ... Stop LLD2 daemon ... [/var/run/lld2d_start.sh] ... Start LLD2 daemon ... [/var/run/vlan_stop.sh] ... [/var/run/vlan_start.sh] ... [/var/run/eth0_vlan_stop.sh] ... [/var/run/eth0_vlan_start.sh] ... disable VLAN [/usr/sbin/submit] CAPTIVAL_PORTAL ... Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1 le: /var/run/hostapd.ath0.ap_bss [/var/run/captival_portal_stop.sh] ... captival portal already stop [/var/run/captival_portal_start.sh] ... captival_state 0 captibr0: port 2(ath0) entering disabled state val portal is diALPHA:[SNMP-TRAP][Specific=13] sable [/usr/sbin/submit] LOADBALANCE ... DEVICE IS DOWN ifname=ath0 ath0: Could not DEVICE IS DOWN ifname=ath0 connect to kernel driver Using interface ath0 with hwaddr 54:b8:0a:35:08:90 and ssid 'CyberNetA' [/etc/templates/loadbalance.sh] restart ... [/var/run/loadbalance_stop.sh] ... [/usr/sbin/submit] QOS_TC_TM ... Stop loadbalance ... lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wireless extensions. wifi1 no wireless extensions. [/var/run/loadbalance_start.sh] ... [/var/run/tc_monitor_stop.sh] ... tc monitor already stop ALPHA:[Wireless] 2.4G:Initiate Wireless success ALPHA:[SNMP-TRAP][Specific=7] br0: port 2(ath0) entering forwarding state Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=643, new mode=3, valid=1 le: /var/run/hoswmi_unified_vdev_stop_send for vap 0 (86590000) tapd.ath16.ap_bsSTOPPED EVENT for vap 0 (86590000) s : not found br0: port 3(ath16) entering disabled state DEVICE IS DOWN ifname=ath16 ath16: Could not DEVICE IS DOWN ifname=ath16 connect to kernel driver Using interface ath16 with hwaddr 54:b8:0a:35:08:98 and ssid 'CyberNetX' OL vap_stop + wmi_unified_vdev_stop_send for vap 0 (86590000) OL vap_stop - STOPPED EVENT for vap 0 (86590000) OL vap_start + wmi_unified_vdev_start_send for vap 0 (86590000) OL vap_start - ol_vdev_start_resp_ev for vap 0 (86590000) ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: ol_if_dfs_configure: called ol_if_dfs_configure: ETSI domain ol_if_dfs_disable: called ol_if_dfs_enable: called cac_start chan 5580 timeout 612 sec, curr time: 4294716 sec Notification to UMAC VAP layer ALPHA:[Wireless] 5G:Initiate Wireless success ALPHA:[SNMP-TRAP][Specific=7] br0: port 3(ath16) entering forwarding state FWLOG: [62518] WAL_DBGID_SECURITY_ENCR_EN ( ) FWLOG: [62518] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [/var/run/trafficmgr_stop.sh] ... [/var/run/qos_stop.sh] ... FWLOG: [63322] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xf75a, 0x200008a, 0x0, 0x15 ) [/var/run/tc_monitor_start.sh] ... tc monitor is disable [/var/run/qos_start.sh] ... Start QOS system ... QOS is disabled. [/var/run/trafficmgr_start.sh] ... Start traffic manager system ... traffic manager is disabled. [/usr/sbin/submit] NETFILTER ... #!/bin/sh netfilter.sh... netfilter_flag: 0 [/usr/sbin/submit] ARP_SPOOFING ... [/etc/templates/arpspoofing.sh] restart ... [/var/run/arpspoofing_stop.sh] ... sleep 5..... Stop arp spoofing prevention... [/var/run/arpspoofing_start.sh] ... Start arp spoofing prevention ... arp spoofing prevention is disabled. ---Checking System Memory..OK, Current Free Memoey is 80428 KB Radar found on channel 116 (5580 MHz) ol_if_dfs_clist_update: called, cmd=1, nollist=8657f220, nentries=4 set channel freq 5560 DCS previous state is restored ALPHA:[SNMP-TRAP][Specific=16] ALPHA:[Wireless]5GHz Wireless Channel Changed to 112 channel by DFS ol_vdev_start_resp_ev for vap 0 (86590000) ol_if_dfs_configure: called ol_if_dfs_configure: ETSI domain ol_if_dfs_disable: called ol_if_dfs_enable: called cac_start chan 5560 timeout 65 sec, curr time: 4294803 sec Notification to UMAC VAP layer cac_timeout cac expired, chan 5560 curr time 4294868 wmi_unified_vdev_up_send for vap 0 (86590000)


U-Boot 1.1.4 (Jan 26 2014 - 16:16:52) ap135 - Scorpion 1.0 ALPHA U-boot v1.00rc002 DRAM: sri Scorpion 1.0 ath_ddr_initial_config(178): (32bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x2, 0x1c) Tap values = (0xf, 0xf, 0xf, 0xf) 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 243k for U-Boot at: 87fc0000 Reserving 192k for malloc() at: 87f90000 Reserving 44 Bytes for Board Info at: 87f8ffd4 Reserving 36 Bytes for Global Data at: 87f8ffb0 Reserving 128k for boot params() at: 87f6ffb0 Stack Pointer at: 87f6ff98 Now running in RAM - U-Boot at: 87fc0000 Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18 flash size 16MB, sector count = 256 Flash: 16 MB *** Warning - bad CRC, using default environment *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... athrs_sgmii_res_cal: cal value = 0xe ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->f1e PHY* : cfg1 0x80000000 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 4, Neg Success ATHRSF1_PHY: unit 0 phy addr 4 eth0 up eth0 Setting 0x18116290 to 0x60c0214f press 'q' to stop autoboot: 0 ## Booting image at 9f070000 ... Image Name: 7zip Linux Kernel Created: 1970-01-01 0:00:00 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: -1 Bytes = 4096 MB Load Address: 80002000 Entry Point: 80002000 Uncompressing Kernel Image with LZMA ... Check Image ... Image OK! OK No initrd ## Transferring control to Linux (at address 80002000) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... [ 0.000000] Linux version 4.19.123 (sebastian@sebastian-msi) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13213+1-146e18af56)) #0 Fri Jun 19 13:50:29 2020 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc) [ 0.000000] MIPS: machine is D-Link DAP-2660 A1 [ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 122360K/131072K available (4328K kernel code, 176K rwdata, 1032K rodata, 1240K init, 206K bss, 8712K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 720.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns [ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns [ 0.008291] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848) [ 0.042885] pid_max: default: 32768 minimum: 301 [ 0.047994] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.055047] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.066759] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.077161] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.083774] pinctrl core: initialized pinctrl subsystem [ 0.090154] NET: Registered protocol family 16 [ 0.122279] clocksource: Switched to clocksource MIPS [ 0.128748] NET: Registered protocol family 2 [ 0.134115] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.142361] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.149796] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.156572] TCP: Hash tables configured (established 1024 bind 1024) [ 0.163450] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.169710] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.176731] NET: Registered protocol family 1 [ 0.184277] Crashlog allocated RAM at address 0x3f00000 [ 0.191149] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.203933] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.210172] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.232092] io scheduler noop registered [ 0.236305] io scheduler deadline registered (default) [ 0.243649] pinctrl-single 1804002c.pinmux: 544 pins, size 68 [ 0.250761] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.258153] console [ttyS0] disabled [ 0.262018] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A [ 0.271211] console [ttyS0] enabled [ 0.271211] console [ttyS0] enabled [ 0.278631] bootconsole [early0] disabled [ 0.278631] bootconsole [early0] disabled [ 0.303739] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.308590] 9 fixed-partitions partitions found on MTD device spi0.0 [ 0.315047] Creating 9 MTD partitions on "spi0.0": [ 0.319929] 0x000000000000-0x000000040000 : "bootloader" [ 0.326059] 0x000000040000-0x000000050000 : "bdcfg" [ 0.331741] 0x000000050000-0x000000060000 : "rgdb" [ 0.337315] 0x000000060000-0x000000070000 : "unknown" [ 0.343160] 0x000000070000-0x000000f50000 : "firmware" [ 0.353130] 2 wrgg-fw partitions found on MTD device firmware [ 0.359011] Creating 2 MTD partitions on "firmware": [ 0.364066] 0x000000000000-0x000000600000 : "kernel" [ 0.369789] 0x000000600000-0x000000ee0000 : "rootfs" [ 0.375507] mtd: device 6 (rootfs) set to be root filesystem [ 0.382629] 1 squashfs-split partitions found on MTD device rootfs [ 0.388953] 0x0000008d0000-0x000000ee0000 : "rootfs_data" [ 0.395149] 0x000000f50000-0x000000f70000 : "langpack" [ 0.401098] 0x000000f70000-0x000000fe0000 : "captival" [ 0.407040] 0x000000fe0000-0x000000ff0000 : "certificate" [ 0.413238] 0x000000ff0000-0x000001000000 : "art" [ 0.420385] libphy: Fixed MDIO Bus: probed [ 0.427337] ag71xx 19000000.eth: invalid MAC address, using random address [ 0.752083] libphy: ag71xx_mdio: probed [ 0.756141] mdio_bus mdio.0: MDIO device at address 0 is missing. [ 0.762407] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 0.770266] i2c /dev entries driver [ 0.775594] NET: Registered protocol family 10 [ 0.784062] Segment Routing with IPv6 [ 0.787940] NET: Registered protocol family 17 [ 0.792546] 8021q: 802.1Q VLAN Support v1.8 [ 0.797642] PCI host bridge /ahb/pcie-controller@180c0000 ranges: [ 0.803888] MEM 0x0000000010000000..0x0000000011ffffff [ 0.809203] IO 0x0000000000000000..0x0000000000000000 [ 0.814671] PCI host bridge to bus 0000:00 [ 0.818864] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.825846] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.831512] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.838412] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.847711] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.855188] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.862755] PCI host bridge /ahb/pcie-controller@18250000 ranges: [ 0.868989] MEM 0x0000000012000000..0x0000000013ffffff [ 0.874307] IO 0x0000000000000001..0x0000000000000001 [ 0.879621] ar724x-pci 18250000.pcie-controller: PCIe link is down [ 0.886047] PCI host bridge to bus 0000:01 [ 0.890241] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff] [ 0.897224] pci_bus 0000:01: root bus resource [io 0x0001] [ 0.902889] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0] [ 0.909789] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.919008] ag71xx 19000000.eth: invalid MAC address, using random address [ 1.174276] random: fast init done [ 1.239364] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.247431] ag71xx 19000000.eth: invalid MAC address, using random address [ 1.571357] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.583365] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.594991] Freeing unused kernel memory: 1240K [ 1.599610] This architecture does not have kernel memory protection. [ 1.606152] Run /sbin/init as init process [ 2.163811] init: Console is alive [ 2.167506] init: - watchdog - [ 2.875724] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.936337] ag71xx 19000000.eth: invalid MAC address, using random address [ 2.944016] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.961755] init: - preinit - [ 3.332691] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 3.794988] random: jshn: uninitialized urandom read (4 bytes read) [ 3.903063] random: jshn: uninitialized urandom read (4 bytes read) [ 3.946013] random: jshn: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.265209] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 7.291635] urandom-seed: Seed file not found (/etc/urandom.seed) [ 7.387692] procd: - early - [ 7.390753] procd: - watchdog - [ 8.013029] procd: - watchdog - [ 8.016497] procd: - ubus - [ 8.145557] urandom_read: 5 callbacks suppressed [ 8.145564] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.241585] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.249406] procd: - init - Please press Enter to activate this console. [ 8.832462] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.989356] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 8.997085] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 9.063121] xt_time: kernel timezone is -0000 [ 9.196836] PPP generic driver version 2.4.2 [ 9.211259] NET: Registered protocol family 24 [ 9.264519] urngd: v1.0.2 started. [ 9.327331] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=13 [ 9.334693] ag71xx 19000000.eth: invalid MAC address, using random address [ 9.430618] kmodloader: done loading kernel modules from /etc/modules.d/* [ 9.590657] random: crng init done [ 9.706523] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 36.759035] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 36.782340] jffs2_build_filesystem(): unlocking the mtd device... [ 36.782384] done. [ 36.790624] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 37.579550] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 39.920780] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 40.052176] br-lan: port 1(wlan0) entered blocking state [ 40.057614] br-lan: port 1(wlan0) entered disabled state [ 40.063367] device wlan0 entered promiscuous mode [ 41.284738] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 41.291396] br-lan: port 1(wlan0) entered blocking state [ 41.296835] br-lan: port 1(wlan0) entered forwarding state [ 41.347744] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 57.360470] done. [ 57.362491] jffs2: notice: (1410) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 57.525405] overlayfs: upper fs does not support tmpfile.


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/01/20 20:14
  • by s_2