D-Link DAP-2230 A1

The DAP-2230 is an N300 Wall-Mount PoE Access Point from the D-Link DAP Series of Business Access Points, manufactured by Alpha Networks.

→ Please see the main article for the DAP-2xxx series for flashing instructions.

start size label
0x00000000 0x00040000 (256k) bootloader
0x00040000 0x00010000 (64k) bdcfg
0x00050000 0x00010000 (64k) rgdb
0x00060000 0x00010000 (64k) unknown
0x00070000 0x00ee0000 (15232k) firmware
0x00f50000 0x00020000 (128k) langpack
0x00f70000 0x00070000 (448k) captival
0x00fe0000 0x00010000 (64k) certificate
0x00ff0000 0x00010000 (64k) art

→ → Please see the main article for the DAP-2xxx series for unbricking instructions.

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The D-Link DAP-2230 has the following buttons:

BUTTON GPIO
Reset 17

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

Remove 4 screws (PH2), pull case apart.

Main PCB:
Insert photo of PCB

→ Please see the main article for the DAP-2xxx series for serial_console.

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

U-Boot 1.1.4 (Aug 27 2015 - 14:06:48) ap143 - Honey Bee 2.0 ALPHA U-boot v1.00rc002 DRAM: sri Honey Bee 2.0 ath_ddr_initial_config(195): (16bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x4, 0x31) Tap values = (0x1a, 0x1a, 0x1a, 0x1a) 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 244k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98 Now running in RAM - U-Boot at: 83fc0000 Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18 flash size 16MB, sector count = 256 Flash: 16 MB *** Warning - bad CRC, using default environment *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->S27 PHY* S27 reg init : cfg1 0x800c0000 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 eth0 up Honey Bee ----> MAC 1 S27 PHY * S27 reg init ATHRS27: resetting s27 ATHRS27: s27 reset done : cfg1 0x800c0000 cfg2 0x7214 eth1: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10 athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 eth1 up eth0, eth1 Setting 0x181162c0 to 0x50a1a100 press 'q' to stop autoboot: 0 ## Booting image at 9f070000 ... Image Name: 7zip Linux Kernel Created: 1970-01-01 0:00:00 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: -1 Bytes = 4096 MB Load Address: 80002000 Entry Point: 80002000 Uncompressing Kernel Image with LZMA ... Check Image ... Image OK! OK No initrd ## Transferring control to Linux (at address 80002000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... Booting QCA953x Linux version 2.6.31--LSDK-10.2.85 (release@cdWSCMPL06) (gcc version 4.3.3 (GCC) ) #1 Wed Jul 13 13:34:35 CST 2016 flash_size passed from bootloader = 16 CPU revision is: 00019374 (MIPS 24Kc) ath_sys_frequency: cpu apb ddr apb cpu 650 ddr 392 ahb 216 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock0 rw mem=64m PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 47632k/65536k available (2179k kernel code, 17828k reserved, 477k data, 144k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 433.15 BogoMIPS (lpj=866304) Mount-cache hash table entries: 512 ****************ALLOC*********************** Packet mem: 802d06c0 (0xe00000 bytes) ******************************************** NET: Registered protocol family 16 ath_pcibios_init: bus 0 ***** Warning PCIe 0 H/W not found !!! registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 93 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled brd: module loaded ELBOX CFI physmap flash device: 1000000 at 9f000000 ATH serial flash !! ath-nor0: squashfs filesystem found at offset 0x00160000 Creating 11 MTD partitions on "ath-nor0": 0x0000001600c0-0x0000009870c0 : "rootfs" 0x000000070000-0x000000f50000 : "upgrade" 0x000000050000-0x000000060000 : "rgdb" 0x000000040000-0x000000050000 : "bdcfg" 0x000000f50000-0x000000f70000 : "langpack" 0x000000fe0000-0x000000ff0000 : "certificate" 0x000000ff0000-0x000001000000 : "radiocfg" 0x000000000000-0x000001000000 : "flash" 0x000000000000-0x000000040000 : "bootloader" 0x000000040000-0x000000050000 : "boot config" 0x000000f70000-0x000000fe0000 : "captival" u32 classifier Actions configured arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> athwdt_init: Registering WDT success VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 144k freed init started: BusyBox v1.14.1 (2016-07-13 13:34:37 CST) starting pid 131, tty '': '/etc/init.d/rcS' [/etc/init.d/S03config.sh] Mounting proc and var ... SymbLink /dev/mtdblock/0 SymbLink /dev/mtdblock/1 SymbLink /dev/mtdblock/10 SymbLink /dev/mtdblock/2 SymbLink /dev/mtdblock/3 SymbLink /dev/mtdblock/4 SymbLink /dev/mtdblock/5 SymbLink /dev/mtdblock/6 SymbLink /dev/mtdblock/7 SymbLink /dev/mtdblock/8 SymbLink /dev/mtdblock/9 Inserting modules ... Inserting Rebootm ... Rebootm loading ... Inserting atheros ethernet ... qca955x_GMAC: Length per segment 1536 953x_GMAC: qca953x_gmac_attach Link Int Enabled qca953x_set_gmac_caps CHECK DMA STATUS 953x_GMAC: qca953x_gmac_attach Link Int Enabled qca953x_set_gmac_caps CHECK DMA STATUS mac:1 Registering S27.... qca955x_GMAC: RX TASKLET - Pkts per Intr:18 qca955x_GMAC: Mac address for unit 1:bfff0006 qca955x_GMAC: ff:ff:ff:ff:ff:ff qca955x_GMAC: Max segments per packet : 1 qca955x_GMAC: Max tx descriptor count : 128 qca955x_GMAC: Max rx descriptor count : 128 qca955x_GMAC: Mac capability flags : 2D89 Inserting gpio ... GPIO driver initialized. done. Start xmldb ... [/etc/scripts/misc/profile.sh] getnew ... [/etc/scripts/misc/defnodes.sh] ... [/etc/defnodes/S10setext.sh] ... PHP [/etc/defnodes/S11setnodes.php] ... PHP [/etc/defnodes/S12features.php] ... PHP [/etc/defnodes/S13flashspeed.php] ... PHP [/etc/defnodes/S20setnodes.php] ... mount: mounting /dev/mtdblock/4 on /www/locale/alt failed: Invalid argument PHP [/etc/defnodes/S40brand.php] ... [/etc/scripts/misc/defnodes.sh] Done !! [/etc/templates/timezone.sh] ... [/etc/templates/logs.sh] ... [/var/run/logs_run.sh] ... gpio set led status [/etc/templates/powerled.sh] ... [/var/run/powerled_run.sh] ... athr_gmac_ring_alloc Allocated 2048 at 0x83a1d800 athr_gmac_ring_alloc Allocated 2048 at 0x83a1d000 HONEYBEE ----> S27 PHY MDIO ATHRS27: resetting s27 ATHRS27: s27 reset done Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... ADDRCONF(NETDEV_UP): eth0: link is not ready [/etc/init.d/S03config.sh] done! [/etc/init.d/S10system.sh] Write some proc file ... Enable panic timeout when Kernel panic ... start Layout ... [/etc/scripts/layout.sh] start ... [/var/run/layout_start.sh] ... Start bridge layout ... device eth0 entered promiscuous mode start LAN ... [/etc/templates/lan.sh] ... [/var/run/lan_start.sh] ... Bridge mode selected, LAN is disabled ! start web server ... [/etc/templates/webs.sh] start ... [/var/run/webs_start.sh] ... Starting HTTPD ... nvram: not found nvram: not found start eth0 vlan setup ... [/etc/scripts/eth_vlan.sh] start ... [/var/run/eth0_vlan_start.sh] ... disable VLAN #!/bin/sh limitedadmin.sh... [/etc/scripts/eth_vlan.sh] start ... [/var/run/eth0_vlan_stop.sh] ... [/var/run/eth0_vlan_start.sh] ... disable VLAN #!/bin/sh pingctl.sh... start fresetd ... rxcheck: not found enable LAN ports ... Factory reset time : 5 secs System reset time : 1 secs WPS command : [/etc/templates/wps.sh pbc &] [/etc/scripts/enlan.sh] ... Generate channel table according to the country code... generate country domain mapping table Generate VLAN table according to the port... start WAN ... Set WAN port media type 0 slinktype: not found [/etc/templates/wan.sh] start ... [/var/run/eth0_vlan_start.sh] ... disable VLAN [/var/run/wan_start.sh] ... Bridge mode selected ! Start WAN(br0),192.168.0.50/255.255.255.0 ... [/etc/templates/wanup.sh] ... [/var/run/wan_up.sh] ... [/etc/templates/ntp.sh] ... killall: ntpclient: no process killed NTP client is disabled ... [/etc/templates/upnpd.sh] ... [/var/run/upnpd_start.sh] ... UPNP function is not enabled !! /etc/templates/webredirect.sh: not found [/usr/sbin/submit] CAPTIVAL_PORTAL ... [/var/run/captival_portal_stop.sh] ... captival portal already stop [/var/run/captival_portal_start.sh] ... captival_state 0 captival portal is disable >>>/var/run/wan_start.sh: Start IPv6 configuration >>> Disable IPv6. <<< End of IPv6 <<< captival_tar prep ... remains :457216bytes nvram: not found nvram: not found start stunnel ... [/etc/templates/stunnel.sh] ... Setting certificate. [/var/run/stunnel_start.sh] ... Starting universal SSL tunnel: stunnel. Enable wlan restart ... wlanRestart: not found start WLAN ... [/etc/templates/wlan.sh] ... SERVD: stop service [WLAN] SERVD: service [WLAN] is already stopped. SERVD: start service [WLAN] start telnet daemon ... Start telnetd ... [/etc/templates/wlan_run.sh] start ... nvram: not found nvram: not found start SSHD daemon ... [/etc/templates/sshd.sh] ... [/etc/templates/autorekey.sh] ... [/var/run/autorekey_start_g.sh] ... [/var/run/autorekey_start_a.sh] ... [/var/run/sshd_start.sh] ... start sshd ... Disable start-up daemon: sshd. start DHCP server [/etc/templates/dhcpd.sh] ... start WLAN ..... [/var/run/dhcpd_restart.sh] ... Stop DHCP server (br0) ... Start DHCP server (br0) ... DHCP server is disabled! start SNMP ... [/etc/templates/snmp.sh] ... [/var/run/snmp_start.sh] ... Start SNMP daemon ... start cwmHelper ... start NEAP ... central wifi manager is not enable ,cwmHelper quit [/etc/templates/neaps.sh] start ... [/etc/templates/certs/certscmd.sh] ... [/var/run/neaps_start.sh] ... Start Neap Server ... start NEAPC ... DEVCONF: unable to read config data (ret=-3) ! Getting External certificate for hostapd & wpa_supplicant. Fail! [/var/run/wlan_insmod.sh] ... [/etc/templates/neapc.sh] start ... [/var/run/neapc_start.sh] ... Start NeapC Client ... adf: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Stop apneaps Server ... : not found start APNEAPS_V2 ... [/etc/templates/apneaps_v2.sh] start ... Stop apneaps_v2 Server ... start AUTORFC ... [/etc/templates/autorf.sh] start ... Stop autorf client ... start LOADBALANCE ... [/etc/templates/loadbalance.sh] start ... [/var/run/loadbalance_start.sh] ... start Microsoft LLDP ... [/etc/templates/lld2d.sh] ... ############## snmp beacon oid init ############## ############## snmp init ############## [/var/run/lld2d_start.sh] ... Start LLD2 daemon ... start Ethlink ... start Trap Monitor ... [/etc/templates/arpspoofing.sh] start ... [/var/run/arpspoofing_start.sh] ... Start arp spoofing prevention ... arp spoofing prevention is disabled. #!/bin/sh netfilter.sh... netfilter_flag: 0 start DHCP multicast to unicast ... #!/bin/sh dhcp_mc2uc.sh... [/etc/init.d/S10system.sh] done! rcS done! Please press Enter to activate this console. ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, TX_ATA_SWAP, RX_DATA_SWAP, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved insmod: can't insert '/lib/modules/ath_dfs.ko': unknown symbol in module, or unknown parameter getaddrinfo: Name or service not known Creating directory: /var/net-snmp NET-SNMP version 5.4.1 ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_ahb: 10.2-00082-4 (Atheros/multi-bss) __ath_attach: Set global_scn[0] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead *** ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=512 Enterprise mode: 0x03fc0000 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6164] rx chainmask mismatch actual 3 sc_chainmak 0 ath_get_caps[6139] tx chainmask mismatch actual 3 sc_chainmak 0 wifi0: Atheros ???: mem=0xb8100000, irq=2 ath_pci: 10.2-00082-4 (Atheros/multi-bss) [/var/run/wlan_start.sh] ... wlan_vap_create : enter. devhandle=0x82840360, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x82840360, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created ath0 Start WLAN interface ath0 ... sc nodebug 0 Interface doesn't accept private ioctl... ForBiasAuto (8BE0): Operation not permitted ====essid: DES SSID SET=dlink dlink,len:5,pathSet freq vap stop send + 82af8000 :/var/run/ath0.sSet freq vap stop send -82af8000 sid==== Set wait done --82af8000 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 Invalid command : preferred5g [/var/run/wlan_start.sh] ... sleep 2..... [/var/run/wlan_device_up.sh] ... UP 2.4G interface ! Set freq vap stop send + 82af8000 Set freq vap stop send -82af8000 Filter Accept CHLOAD Param Over RSSI ---Chan 11 cur 109 min 130 delta -21 allowed 10 Best Channel Selected 11 rssi 130 nf -97 Set wait done --82af8000 device ath0 entered promiscuous mode ALPHA:[Wireless]Initiate Wireless ath0 success ALPHA:[SNMP-TRAP][Specific=7] br0: port 2(ath0) entering forwarding state Filter Accept CHLOAD Param Over RSSI ---Chan 11 cur 105 min 124 delta -19 allowed 10 Best Channel Selected 11 rssi 124 nf -97 br0: port 2(ath0) multicast bandwidth all br0: port 1(eth0) multicast bandwidth all : not found [/etc/templates/lld2d.sh] ... [/var/run/lld2d_stop.sh] ... Stop LLD2 daemon ... [/var/run/lld2d_start.sh] ... Start LLD2 daemon ... [/var/run/vlan_stop.sh] ... [/var/run/vlan_start.sh] ... [/var/run/eth0_vlan_stop.sh] ... [/var/run/eth0_vlan_start.sh] ... disable VLAN [/usr/sbin/submit] CAPTIVAL_PORTAL ... [/var/run/captival_portal_stop.sh] ... captival portal already stop [/var/run/captival_portal_start.sh] ... captival_state 0 captival portal is disable [/usr/sbin/submit] LOADBALANCE ... [/etc/templates/loadbalance.sh] restart ... [/var/run/loadbalance_stop.sh] ... [/usr/sbin/submit] QOS_TC_TM ... Stop loadbalance ... lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wireless extensions. [/var/run/tc_monitor_stop.sh] ... tc monitor already stop [/var/run/loadbalance_start.sh] ... [/var/run/trafficmgr_stop.sh] ... [/var/run/qos_stop.sh] ... [/var/run/tc_monitor_start.sh] ... tc monitor is disable [/var/run/qos_start.sh] ... Start QOS system ... QOS is disabled. [/var/run/trafficmgr_start.sh] ... Start traffic manager system ... traffic manager is disabled. [/usr/sbin/submit] NETFILTER ... #!/bin/sh netfilter.sh... netfilter_flag: 0 [/usr/sbin/submit] ARP_SPOOFING ... [/etc/templates/arpspoofing.sh] restart ... sleep 5..... [/var/run/arpspoofing_stop.sh] ... Stop arp spoofing prevention... [/var/run/arpspoofing_start.sh] ... Start arp spoofing prevention ... arp spoofing prevention is disabled. ---Checking System Memory..OK, Current Free Memoey is 24128 KB


U-Boot 1.1.4 (Aug 27 2015 - 14:06:48) ap143 - Honey Bee 2.0 ALPHA U-boot v1.00rc002 DRAM: sri Honey Bee 2.0 ath_ddr_initial_config(195): (16bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x4, 0x31) Tap values = (0x1a, 0x1a, 0x1a, 0x1a) 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 244k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98 Now running in RAM - U-Boot at: 83fc0000 Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18 flash size 16MB, sector count = 256 Flash: 16 MB *** Warning - bad CRC, using default environment *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->S27 PHY* S27 reg init : cfg1 0x800c0000 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 eth0 up Honey Bee ----> MAC 1 S27 PHY * S27 reg init ATHRS27: resetting s27 ATHRS27: s27 reset done : cfg1 0x800c0000 cfg2 0x7214 eth1: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10 athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 eth1 up eth0, eth1 Setting 0x181162c0 to 0x50a1a100 press 'q' to stop autoboot: 0 ## Booting image at 9f070000 ... Image Name: 7zip Linux Kernel Created: 1970-01-01 0:00:00 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: -1 Bytes = 4096 MB Load Address: 80002000 Entry Point: 80002000 Uncompressing Kernel Image with LZMA ... Check Image ... Image OK! OK No initrd ## Transferring control to Linux (at address 80002000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 4.19.123 (sebastian@sebastian-msi) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13213+1-146e18af56)) #0 Sun Jun 14 22:04:35 2020 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is D-Link DAP-2230 A1 [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 57452K/65536K available (4328K kernel code, 176K rwdata, 1032K rodata, 1240K init, 206K bss, 8084K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 650.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000010] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008275] Calibrating delay loop... 431.10 BogoMIPS (lpj=862208) [ 0.042764] pid_max: default: 32768 minimum: 301 [ 0.047902] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.054907] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.068060] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.078417] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.085056] pinctrl core: initialized pinctrl subsystem [ 0.091911] NET: Registered protocol family 16 [ 0.136180] clocksource: Switched to clocksource MIPS [ 0.143196] NET: Registered protocol family 2 [ 0.148955] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.157190] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.164573] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.171304] TCP: Hash tables configured (established 1024 bind 1024) [ 0.178221] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.184479] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.191622] NET: Registered protocol family 1 [ 0.201968] Crashlog allocated RAM at address 0x3f00000 [ 0.209701] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.224884] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.231105] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.259576] io scheduler noop registered [ 0.263800] io scheduler deadline registered (default) [ 0.271731] pinctrl-single 1804002c.pinmux: 576 pins, size 72 [ 0.279076] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.286732] console [ttyS0] disabled [ 0.290623] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.299752] console [ttyS0] enabled [ 0.299752] console [ttyS0] enabled [ 0.307318] bootconsole [early0] disabled [ 0.307318] bootconsole [early0] disabled [ 0.326865] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.332267] 9 fixed-partitions partitions found on MTD device spi0.0 [ 0.338851] Creating 9 MTD partitions on "spi0.0": [ 0.343826] 0x000000000000-0x000000040000 : "bootloader" [ 0.350444] 0x000000040000-0x000000050000 : "bdcfg" [ 0.356660] 0x000000050000-0x000000060000 : "rgdb" [ 0.362692] 0x000000060000-0x000000070000 : "unknown" [ 0.369038] 0x000000070000-0x000000f50000 : "firmware" [ 0.381444] 2 wrgg-fw partitions found on MTD device firmware [ 0.387433] Creating 2 MTD partitions on "firmware": [ 0.392605] 0x000000000000-0x000000600000 : "kernel" [ 0.398801] 0x000000600000-0x000000ee0000 : "rootfs" [ 0.404958] mtd: device 6 (rootfs) set to be root filesystem [ 0.413034] 1 squashfs-split partitions found on MTD device rootfs [ 0.419525] 0x000000880000-0x000000ee0000 : "rootfs_data" [ 0.426183] 0x000000f50000-0x000000f70000 : "langpack" [ 0.432726] 0x000000f70000-0x000000fe0000 : "captival" [ 0.439086] 0x000000fe0000-0x000000ff0000 : "certificate" [ 0.445785] 0x000000ff0000-0x000001000000 : "art" [ 0.454246] libphy: Fixed MDIO Bus: probed [ 0.462786] ag71xx 19000000.eth: invalid MAC address, using random address [ 0.785276] ag71xx 19000000.eth: Could not find valid phy node [ 0.791690] ag71xx 1a000000.eth: invalid MAC address, using random address [ 1.136174] random: fast init done [ 1.428639] libphy: ag71xx_mdio: probed [ 1.434269] libphy: ar8xxx-mdio: probed [ 1.448484] switch0: Atheros AR8229 rev. 1 switch registered on mdio.0 [ 1.496273] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.506393] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 1.513009] i2c /dev entries driver [ 1.518944] NET: Registered protocol family 10 [ 1.530569] Segment Routing with IPv6 [ 1.534588] NET: Registered protocol family 17 [ 1.539335] 8021q: 802.1Q VLAN Support v1.8 [ 1.551754] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.569355] Freeing unused kernel memory: 1240K [ 1.574079] This architecture does not have kernel memory protection. [ 1.580746] Run /sbin/init as init process [ 2.213717] init: Console is alive [ 2.217682] init: - watchdog - [ 3.064787] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.135953] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.154125] init: - preinit - [ 4.169054] random: jshn: uninitialized urandom read (4 bytes read) [ 4.294396] random: jshn: uninitialized urandom read (4 bytes read) [ 4.348741] random: jshn: uninitialized urandom read (4 bytes read) [ 4.562601] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 5.601392] eth0: link up (1000Mbps/Full duplex) [ 5.606270] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.805703] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 8.843991] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.960152] eth0: link down [ 8.979497] procd: - early - [ 8.982754] procd: - watchdog - [ 9.641713] procd: - watchdog - [ 9.645474] procd: - ubus - [ 9.792818] urandom_read: 5 callbacks suppressed [ 9.792828] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.889568] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.898134] procd: - init - Please press Enter to activate this console. [ 10.707163] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.876970] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 10.884881] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 10.973899] xt_time: kernel timezone is -0000 [ 11.182784] PPP generic driver version 2.4.2 [ 11.201663] NET: Registered protocol family 24 [ 11.241676] urngd: v1.0.2 started. [ 11.344775] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.492662] random: crng init done [ 33.948429] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 33.968270] jffs2_build_filesystem(): unlocking the mtd device... [ 33.968281] done. [ 33.976700] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 34.696521] eth0: link up (1000Mbps/Full duplex) [ 34.712446] br-lan: port 1(eth0) entered blocking state [ 34.717916] br-lan: port 1(eth0) entered disabled state [ 34.723751] device eth0 entered promiscuous mode [ 34.753812] br-lan: port 1(eth0) entered blocking state [ 34.759264] br-lan: port 1(eth0) entered forwarding state [ 34.765141] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 35.714546] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 56.220747] done. [ 56.222795] jffs2: notice: (1366) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 56.435633] overlayfs: upper fs does not support tmpfile.


Space for additional notes, links to forum threads or other resources.

  • ...

FIXME Add tags below, then remove this fixme.

How to add tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1