D-Link DAP-1533

The D-Link DAP-1533 is a wireless N dualband (not simultaneous) gigabit access point.

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
DAP-1533 A1 20 Feb 2012 - - -
Main chip Ram Flash Network USB Serial JTag
Atheros AR7370-BC2A@560MHz 128MiB 8MiB 4 Yes Yes ?

Manufacturer's site: http://us.dlink.com/us/en/home-solutions/connect/access-points-range-extenders-and-bridges/dap-1533-wireless-n450-mediabridge-access-point.html

Forum: FIXME

D-Link DAP-1533 OEM
partition start end Name
mtd0 0x000000000000 0x000000020000 “u-boot”
mtd1 0x000000020000 0x000000030000 “nvram”
mtd2 0x000000030000 0x0000007b0000 “linux4”
mtd3 0x000000150000 0x0000007b0000 “rootfs”
mtd4 0x0000007b0000 0x0000007e0000 “LANG”
mtd5 0x0000007e0000 0x0000007f0000 “MAC”
mtd6 0x0000007f0000 0x000000800000 “ART”
Instruction set MIPS
Vendor Atheros
bootloader Das U-Boot
System-On-Chip Atheros AR7370-BC2A
CPU @Frq MIPS 74Kc @560MHz
Flash size 8 MB
Flash Chip MX25L6406E
RAM size 128 MB
RAM Chip M14D5121632A 2 pcs
Wireless No1 Atheros AR9380 w/ 3×3 MIMO antennas for 2.4GHz or 5GHz 802.11a/b/g/n
switch Atheros AR8327N
Modem none
USB Yes
Serial Yes
JTAG :?:

Front:

Back:

Note: This will void your warranty!

  • FIXME

Main PCB: Modified with external RP-SMA Connectors
D-Link DAP-1533 Main PCB

Main PCB: Top

Main PCB: Bottom

GPIO

port.gpio The AR934x platform (AR7370) provides 23 GPIOs. Some of them are used by the router for status LEDs, buttons and other stuff. The table below shows the results of some investigation (active state low):

Voltage level at GPIO in output-mode gpioX/value in input-mode when GPIO is:
GPIO Common Name PCB Name gpioX/value=1 gpioX/value=0 Floating Pulled to GND Pulled to Vcc
0
1
2
3
4
5
6
7
8
9
10
11 BRIDGE switch
12 LED WLAN DS8 green
13
14 LED System0 DS16 red
15
16 WPS Button
17 RESET Button
18 AP5GHz switch
19 LED Activity DS10 green
20
21
22 LED System1 DS25 green

To make the GPIOs available via sysfs, the required ones have to be exported to userspace, as it is explained on a page of the Squidge-Project. Kernel modules occupying that resource need to be removed before (e.g. “leds-gpio” and “gpio-buttons”). In output-mode, voltage levels of the GPIOs were measured against GND, after the value 1 or 0 had been written to /sys/class/gpio/gpioX/value. In input-mode, the value of the file /sys/class/gpio/gpioX/value was read when the GPIO was floating (initial state), pulled to GND or pulled to Vcc.

port.serial general information about the serial port, serial port cable, etc.

Serial console can be plugged to JP6: connector lacks, it has to be soldered on the board.

How to connect to the Serial Port of this specific device:

You can easily find it, look at the flash in the center of PCB, the serial connector sits next to it:

JP6  . . . .
     4 3 2 1
Pin Signal
1 VCC
2 RxD
3 TxD
4 GND

The settings are: 115200 bauds, 8 bits, no parity, 1 stop bit (115200 8N1)

You are root, once connected to the serial port.

port.jtag general information about the JTAG port, JTAG cable, etc.

FIXME

Jtag pins seems to be located in JP1, but the connector lacks.

How to connect to the JTAG Port of this specific device:

FIXME

U-Boot 1.1.4 Rev: 20 (Nov 9 2011 - 19:56:29) U-boot DB120 DRAM: 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 162k for U-Boot at: 87fd4000 Reserving 192k for malloc() at: 87fa4000 Reserving 44 Bytes for Board Info at: 87fa3fd4 Reserving 36 Bytes for Global Data at: 87fa3fb0 Reserving 128k for boot params() at: 87f83fb0 Stack Pointer at: 87f83f98 Now running in RAM - U-Boot at: 87fd4000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB Using default environment In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:09:0b:ae athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 2 1 0 ## Booting image at 9f030000 ... Image Name: Linux Kernel Image Created: 2012-03-13 12:33:41 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1126377 Bytes = 1.1 MB Load Address: 80002000 Entry Point: 8024c9e0 Verifying Checksum at 0x9f030040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8024c9e0) ... ## bootargs 0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),1536k(linux),6144k(rootfs),192k(LANG),64k(MAC),64k(ART)... ## bootargs @A7F83FB0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART)... ## Giving linux memsize in bytes, 134217728 Starting kernel ... Booting Atheros AR934x Linux version 2.6.31--LSDK-9.2.0_U8.834 (root@david-VM) (gcc version 4.3.3 (GCC) ) #25 Tue Mar 13 20:26:18 CST 2012 flash_size passed from bootloader = 8 arg 1: console=ttyS0,115200 arg 2: root=31:03 arg 3: mem=128M arg 4: rootfstype=squashfs,jffs2 arg 5: init=/sbin/init arg 6: mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART) CPU revision is: 0001974c (MIPS 74Kc) ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 480 ahb 240 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART) PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 126464k/131072k available (2376k kernel code, 4424k reserved, 657k data, 144k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 279.55 BogoMIPS (lpj=559104) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI init:ath_pcibios_init ath_pcibios_init(294): PCI CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci 0000:00:00.0: PME# disabled Returning IRQ 64 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 athwdt_init: Registering WDT success 20000000, 1312D00, USEC_PER_SEC: 1000000,ath_ahb_freq: 240000000 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 247 alg: No test for lzma (lzma-generic) alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered (default) HDLC line discipline maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled brd: module loaded 7 cmdlinepart partitions found on MTD device ath-nor0 Creating 7 MTD partitions on "ath-nor0": 0x000000000000-0x000000020000 : "u-boot" 0x000000020000-0x000000030000 : "nvram" 0x000000030000-0x0000007b0000 : "linux4" 0x000000150000-0x0000007b0000 : "rootfs" 0x0000007b0000-0x0000007e0000 : "LANG" 0x0000007e0000-0x0000007f0000 : "MAC" 0x0000007f0000-0x000000800000 : "ART" TCP cubic registered NET: Registered protocol family 10 lo: Disabled Privacy Extensions NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16 arch/mips/atheros/gpio.c: create_ar531x_gpio_proc_entry: WPS_LED GPIO = 12 ath_otp_init: Registering OTP success ath_clksw_init: Registering Clock Switch Interface success VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 144k freed init started: BusyBox v1.01 (2012.03.13-12:30+0000) multi-call binary init NVRAM_SPACE from mtdblock size init nvram memory map size: 0x10000 order of pages: 0x4 nvram module init: /dev/nvram major number 225 glues to mtd: "nvram" size: 0x00010000 nvram_space: 0x00010000 mapped via mmap(2) openfile :/etc/sysinfo new ver: 1.0 old ver: 1.0 new ver: 1.0 old ver: 1.0 openfile :/etc/sysinfo init artblock :lan_mac=28:10:7B:CA:77:15 to "sys_lan_mac" init artblock :wan_mac=28:10:7B:CA:77:16 to "sys_wan_mac" init artblock :hw_version=A1 to "sys_hw_version" init artblock :wlan0_domain=0x37 to "sys_wlan0_domain" ATHR_GMAC: Length per segment 1536 ATHR_GMAC: fifo cfg 3 01f00140 ATHR_GMAC: RX TASKLET - Pkts per Intr:16 ATHR_GMAC: Mac address for unit 0:bfff0000 ATHR_GMAC: ff:ff:ff:ff:ff:ff ATHR_GMAC: Max segments per packet : 1 ATHR_GMAC: Max tx descriptor count : 40 ATHR_GMAC: Max rx descriptor count : 232 ATHR_GMAC: Mac capability flags : 2381 athr_gmac_ring_alloc Allocated 640 at 0x87a17c00 athr_gmac_ring_alloc Allocated 3712 at 0x879b8000 WASP ----> S17 PHY * Setting Drop CRC Errors, Pause Frames and Length Error frames ### s17 : set 0x610=0x001bd560 ### s17 : set 0x614=0x80010002 ### s17 : set 0x610=0x001b7fe0 ### s17 : set 0x614=0x80020002 athrs17_reg_init:done Setting PHY... Phy setup Complete [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. ADDRCONF(NETDEV_UP): eth0: link is not ready device eth0 is not a slave of br0 interface eth1 does not exist! device eth0.1 entered promiscuous mode device eth0 entered promiscuous mode AR934x GPIO Controller ################ change to AP or Client mode################ nvram_commit: size crc 10000 erasesize:10000, nvram->size: 80251640 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ATH_MAC_TIMER: enet unit:0 is up... RGMii 1000Mbps full duplex ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Port Status 1c000004 ath-ehci ath-ehci.0: ATH EHCI ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected insmod: cannot open module `/lib/modules/2.6.31--LSDK-9.2.0_U8.834/kernel/drivers/usb/host/ohci-hcd.ko': No such file or directory Please press Enter to activate this console. ########################## sysinit #########################service init rc:service_init:init_nvram:start insmod: cannot insert `/lib/devnvram.ko': File exists (-1): File exists openfile :/var/etc/nvram.default rc:service_init:init_nvram:end configuration_version_control: configuration_version= in NVRAM configuration_version_control: configuration_version=1.0 in System =============insert_switch_mod()============== insert_switch_mod: insmod /lib/modules/2.6.31/net/athrs_gmac.ko insmod: cannot insert `/lib/modules/2.6.31/net/athrs_gmac.ko': File exists (-1): File exists device eth0 left promiscuous mode eth0.1: Cannot assign requested address device eth0 entered promiscuous mode eth0.1: Cannot assign requested address eth0.2: Cannot assign requested address eth0.2: Cannot assign requested address device br0 already exists; can't create bridge with the same name device eth0.1 is already a member of a bridge; can't enslave it to bridge br0. br0: port 1(eth0.1) entering forwarding state sh: ./etc/rc.d/pre_customer.sh: not found Wed Mar 14 17:50:00 UTC 2012 modprobe: could not parse modules.dep modprobe: could not parse modules.dep SLIDE on 5GHz Accece Point /tmp/password has been created 2012-03-14 17:50:00: (network.c.239) warning: please use server.use-ipv6 only for hostnames, not without server.bind / empty address; your config will break if the kernel default for IPV6_V6ONLY changes sh: dcc: not found RC Main Loop: START rc is BUSY now! AP Mode or AP Client Mode only need LAN Setting Start LAN start_lan():Support AP and Router Mode Switch killall: udhcpc: no process killed ==========start_ap_lan============ killall: lanmon: no process killed route_add: ifname=br0,rt_destaddr=0.0.0.0,rt_netmask=0.0.0.0,rt_gateway=192.168.1.1,rt_metric=0 route_add: ifname=lo,rt_destaddr=127.0.0.0,rt_netmask=255.0.0.0,rt_gateway=0.0.0.0,rt_metric=0 ##################### wlan1_enable######################### Loading Wireless Modules: country_Code=276 ##########################Loading Wireless Modules: country_Code=276 load DB120 asf: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_pci: 9.2.0_U8.834 (Atheros/multi-bss) __ath_attach: Set global_scn[0] ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 Restoring Cal data from Flash eepromVersion: 02, templateVersion: 02 custData: [ar9300]TxGainTableApply--OSPREY dfs_attach: use DFS enhancements DFS min filter rssiThresh = 18 DFS max pulse dur = 151 ticks ath_get_caps[4834] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[4809] tx chainmask mismatch actual 7 sc_chainmak 0 SC Callback Registration for wifi0 wifi0: Atheros 9380: mem=0x10000000, irq=64 hw_base=0xb0000000 DFS min filter rssiThresh = 22 DFS max pulse dur = 151 ticks Loading Wireless Modules: end set_wlan_mac: start set_wlan_mac: end ##################### set client mode ########################### start_makeVAP: ath_count=0, wds_enable=0, apifnum=0:RF:48:11NAHT40MINUS:1, op_mode=AP start_makeVAP: Ifnum=0, set_RF=RF, Pri_Ch=48, Ch_Mode=11NAHT40MINUS, pure_mode=1, op_mode=AP wlan_vap_create : enter. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created ath0 Invalid command : extoffset DES SSID SET=dlink ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 start_makeVAP: end DES SSID SET=default start_activateVAP: ath_count=0, guest_zone=2, netusb_guest_zone=2 device ath0 entered promiscuous mode br0: port 2(ath0) entering forwarding state device eth0.1 left promiscuous mode br0: port 1(eth0.1) entering disabled state device eth0.1 entered promiscuous mode br0: port 1(eth0.1) entering forwarding state Unknown command: 6to4, use subcommands below dhcp6c : dhcp6c command rdnssd : rdnssd command autoconfig : autoconfig mode start : Start AP IPv6 setting stop : Clean AP IPv6 configuration cli build Dec 9 2011 12:04:53 Unknown command: 6rd, use subcommands below dhcp6c : dhcp6c command rdnssd : rdnssd command autoconfig : autoconfig mode start : Start AP IPv6 setting stop : Clean AP IPv6 configuration cli build Dec 9 2011 12:04:53 Using Switch Chip to find all mac address #################################Start WLAN Finished############################ TFTPD start and listen on port 69. ntp1.dlink.com: Unknown host usbcore: registered new interface driver sxuptp_generic usbcore: registered new interface driver sxuptp_ipod start_route sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found QoS disabled Reading topology file /var/tmp/topology.conf ... 409.860: Reading bss configuration file /var/tmp/WSC_ath0.conf ... ieee80211_ioctl_siwmode: imr.ifm_active=1376896, new mode=3, valid=1 br0: port 2(ath0) entering disabled state Using interface ath0 with hwaddr 28:10:7b:ca:77:15 and ssid 'default' Failed to kill daemon: No such file or directory IDLE rc is IDLE now! DES SSID SET=default br0: port 2(ath0) entering forwarding state 410.661: upnp_wps_device_init called l2_packet_receive - recvfrom: Network is down ~~ ...


*************************************** * U-Boot 1.1.4-59d12316-dirty * * Build: 2017-07-25 * *************************************** ** Warning: bad env CRC, using default, use 'saveenv' to save it in FLASH BOARD: D-Link DAP-1533 SOC: AR9344 rev. 2 CPU: MIPS 74Kc RAM: 128 MB DDR2 32-bit CL3-4-4-10 FLASH: 16 MB Winbond W25Q128 PCIe: 168C:0030 MAC: 28:10:72:31:77:15 CLOCKS: CPU/RAM/AHB/SPI/REF 550/400/200/ 25/ 40 MHz Hit any key to stop booting: 1 0 Booting image from 0x9F030000... Image name: MIPS OpenWrt Linux-4.4.74 Build date: 2017-07-28 11:21:30 UTC Architecture: MIPS OS/image type: Linux Kernel Compression: LZMA Data size: 1.3 MB (1318865 bytes) Load address: 0x80060000 Entry point: 0x80060000 Header CRC... OK! Data CRC... skipped Stopping network... OK! Uncompressing Kernel... OK! Starting kernel... [ 0.000000] Linux version 4.4.74 (taras@taras-ubuntu) (gcc version 5.4.0 (LEDE GCC 5.4.0 r4637-7985bf2) ) #0 Fri Jul 28 11:21:30 2017 [ 0.000000] MyLoader: sysp=084340b2, boardp=5d13924e, parts=c515b44b [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] No valid device tree found, continuing without [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 804123d0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=DAP-1533-A1 console=ttyS0,115200 mtdparts=spi0.0:128k(uboot)ro,64k(nvram)ro,7680k(firmware),192k(lang)ro,64k(mac)ro,64k(art)ro rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125076K/131072K available (2993K kernel code, 147K rwdata, 756K rodata, 320K init, 200K bss, 5996K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns [ 0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns [ 0.008689] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112) [ 0.081672] pid_max: default: 32768 minimum: 301 [ 0.086949] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.094341] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.104913] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.115929] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.123457] NET: Registered protocol family 16 [ 0.129989] MIPS: machine is D-Link DAP-1533 rev. A1 [ 0.137539] registering PCI controller with io_map_base unset [ 0.377964] PCI host bridge to bus 0000:00 [ 0.382546] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.390256] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.396466] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.404045] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.412917] pci 0000:00:00.0: [168c:0030] type 00 class 0x028000 [ 0.412951] pci 0000:00:00.0: invalid calibration data [ 0.418720] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] [ 0.418785] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.418855] pci 0000:00:00.0: supports D1 [ 0.418872] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.419126] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.419164] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.427330] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.435427] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.441772] clocksource: Switched to clocksource MIPS [ 0.448791] NET: Registered protocol family 2 [ 0.454493] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.462320] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.469417] TCP: Hash tables configured (established 1024 bind 1024) [ 0.476614] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.483173] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.490451] NET: Registered protocol family 1 [ 0.495427] PCI: CLS 0 bytes, default 32 [ 0.500049] Crashlog allocated RAM at address 0x3f00000 [ 0.520545] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.527116] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540799] io scheduler noop registered [ 0.545229] io scheduler deadline registered (default) [ 0.551266] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.558847] console [ttyS0] disabled [ 0.582932] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.592564] console [ttyS0] enabled [ 0.599981] bootconsole [early0] disabled [ 0.611954] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.616764] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.622794] Creating 6 MTD partitions on "spi0.0": [ 0.627655] 0x000000000000-0x000000020000 : "uboot" [ 0.635063] 0x000000020000-0x000000030000 : "nvram" [ 0.641733] 0x000000030000-0x0000007b0000 : "firmware" [ 0.658554] 2 uimage-fw partitions found on MTD device firmware [ 0.664618] 0x000000030000-0x000000171f85 : "kernel" [ 0.671066] 0x000000171f85-0x0000007b0000 : "rootfs" [ 0.677863] mtd: device 4 (rootfs) set to be root filesystem [ 0.683699] 1 squashfs-split partitions found on MTD device rootfs [ 0.689979] 0x0000003b0000-0x0000007b0000 : "rootfs_data" [ 0.697205] 0x0000007b0000-0x0000007e0000 : "lang" [ 0.703823] 0x0000007e0000-0x0000007f0000 : "mac" [ 0.710292] 0x0000007f0000-0x000000800000 : "art" [ 0.728598] switch0: Atheros AR8327 rev. 2 switch registered on ag71xx-mdio.0 [ 1.334481] libphy: ag71xx_mdio: probed [ 1.923173] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 1.934697] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 1.943137] NET: Registered protocol family 10 [ 1.951646] NET: Registered protocol family 17 [ 1.956303] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.969252] 8021q: 802.1Q VLAN Support v1.8 [ 1.980323] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.989273] Freeing unused kernel memory: 320K (80430000 - 80480000) [ 3.084410] init: Console is alive [ 3.088088] init: - watchdog - [ 4.181415] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.251031] usbcore: registered new interface driver usbfs [ 4.256765] usbcore: registered new interface driver hub [ 4.262296] usbcore: registered new device driver usb [ 4.273246] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.281660] ehci-platform: EHCI generic platform driver [ 4.287127] ehci-platform ehci-platform: EHCI Host Controller [ 4.293016] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 4.303160] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 4.321817] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 4.329106] hub 1-0:1.0: USB hub found [ 4.333373] hub 1-0:1.0: 1 port detected [ 4.340435] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.348328] ohci-platform: OHCI generic platform driver [ 4.354445] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.372261] init: - preinit - [ 4.741899] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 4.770462] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.905849] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available) [ 5.973039] eth0: link up (1000Mbps/Full duplex) [ 5.977811] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.961074] jffs2: notice: (383) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 7.979199] mount_root: switching to jffs2 overlay [ 8.012732] urandom-seed: Seeding with /etc/urandom.seed [ 8.231336] eth0: link down [ 8.246282] procd: - early - [ 8.249322] procd: - watchdog - [ 8.817922] procd: - watchdog - [ 8.821409] procd: - ubus - [ 8.876558] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.886253] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.895456] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.905301] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.914497] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.923883] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.933237] random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) [ 8.942869] procd: - init - [ 9.397231] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.411336] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.431409] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 9.439595] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 9.450320] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.465492] nf_conntrack version 0.5.0 (1959 buckets, 7836 max) [ 9.537297] xt_time: kernel timezone is -0000 [ 10.385963] asix 1-1:1.0 eth1: register 'asix' at usb-ehci-platform-1, ASIX AX88772B USB 2.0 Ethernet, 00:00:00:00:65:74 [ 10.397224] usbcore: registered new interface driver asix [ 10.548871] PPP generic driver version 2.4.2 [ 10.556101] NET: Registered protocol family 24 [ 10.604606] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.615158] ath: EEPROM regdomain: 0x0 [ 10.615176] ath: EEPROM indicates default country code should be used [ 10.615186] ath: doing EEPROM country->regdmn map search [ 10.615209] ath: country maps to regdmn code: 0x3a [ 10.615221] ath: Country alpha2 being used: US [ 10.615231] ath: Regpair used: 0x3a [ 10.625992] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 10.631426] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40 [ 10.739759] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.791930] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available) [ 11.882696] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available) [ 19.005084] device eth0 entered promiscuous mode [ 19.013255] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 19.884743] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 20.183130] eth0: link up (1000Mbps/Full duplex) [ 20.187988] br-lan: port 1(eth0) entered forwarding state [ 20.193556] br-lan: port 1(eth0) entered forwarding state [ 20.251855] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 21.271109] ath: EEPROM regdomain: 0x8324 [ 21.275234] ath: EEPROM indicates we should expect a country code [ 21.281419] ath: doing EEPROM country->regdmn map search [ 21.286824] ath: country maps to regdmn code: 0x3 [ 21.291598] ath: Country alpha2 being used: UA [ 21.296112] ath: Regpair used: 0x3 [ 21.299576] ath: regdomain 0x8324 dynamically updated by user [ 22.191826] br-lan: port 1(eth0) entered forwarding state [ 24.030198] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 24.130903] device wlan0 entered promiscuous mode [ 25.404940] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 25.411583] br-lan: port 2(wlan0) entered forwarding state [ 25.417247] br-lan: port 2(wlan0) entered forwarding state [ 27.413316] br-lan: port 2(wlan0) entered forwarding state [ 42.501307] random: nonblocking pool is initialized


The machine runs “U-Boot 1.1.4 Rev: 20 (Nov 9 2011 - 19:56:29)”, with the following memory layout:

128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 162k for U-Boot at: 87fd4000 Reserving 192k for malloc() at: 87fa4000 Reserving 44 Bytes for Board Info at: 87fa3fd4 Reserving 36 Bytes for Global Data at: 87fa3fb0 Reserving 128k for boot params() at: 87f83fb0 Stack Pointer at: 87f83f98

After booting, (and pressing q) it says: FIXME

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2019/10/03 12:19
  • by tmomas