Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:d-link:aquila_pro_ai_m30_a1 [2024/07/27 06:55] – old revision restored (2024/07/27 06:46) rolandomagicotoh:d-link:aquila_pro_ai_m30_a1 [2024/07/27 14:45] – [OEM bootlog] rolandomagico
Line 121: Line 121:
  
 <WRAP BOX> <WRAP BOX>
-FIXME //The instructions below are for Broadcom devices and only serve as an example.//\\ +Flashing OpenWrt via OEM web interface is not supported. But there is a recovery web interface which can be used to flash the OpenWrt recovery image: 
-**//Remove modify them if they do not apply to this particular device!//**+   The recovery web interface always flashes to the currently active partition. 
 +   * If OpenWrt is flashed to the second partition, it will not boot. 
 +   * Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end
 +   Set your IP address to 192.168.200.10, subnet mask 255.255.255.0 
 +   Press the reset button while powering on the device 
 +   * Keep the reset button pressed until the LED blinks red 
 +   * Open a Chromium based and go to http://192.168.200.1(recovery web interface) 
 +   * Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-**recovery**.bin 
 +   * The recovery web interface always reports successful flashing, even if it fails 
 +   * After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored) 
 +   * If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt. 
 +   If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are required:
  
-This section deals with +=== Recovering when OEM firmware < 1.10.02 was installed previously === 
-  How you install OpenWrt from a device freshly opened +   * Start the web recovery interface again and flash the decrypted OEM image. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1/. 
-  The steps required such as reset to factory defaults if the device has already been configured+   Now flash the encrypted OEM image via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1/. 
 +   Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
  
-**Note:** Reset router to factory defaults if it has been previously configured. +=== Recovering when OEM firmware >1.10.02 was installed previously ===
-  * Browse to ''<nowiki>http://192.168.1.1/Upgrade.asp</nowiki>'' +
-  * Upload .bin file to router +
-  * Wait for it to reboot +
-  * Telnet to 192.168.1.1 and set a root password, or browse to ''<nowiki>http://192.168.1.1</nowiki>'' if LuCI is installed.+
 </WRAP> </WRAP>
  
Line 330: Line 338:
 ==== OEM bootlog ==== ==== OEM bootlog ====
 <WRAP bootlog> <WRAP bootlog>
 +<nowiki>
 F0: 102B 0000 F0: 102B 0000
 FA: 1040 0000 FA: 1040 0000
Line 478: Line 486:
  ecn no: (200909100001)  ecn no: (200909100001)
  beid rule: 190A  beid rule: 190A
- beid mac: XX:XX:XX:XX:XX:XX+ beid mac: XX:XX:XX:XX:XX:CC
  default ip: 192:168:200:1  default ip: 192:168:200:1
 aup_start Using ethernet@15100000 device aup_start Using ethernet@15100000 device
Line 1076: Line 1084:
 Starting commander: Tue Jul 11 03:26:40 UTC 2023 Starting commander: Tue Jul 11 03:26:40 UTC 2023
 Ether WAN NUM = 1 Ether WAN NUM = 1
-WAN = XX:XX:XX:XX:XX:XX +WAN = XX:XX:XX:XX:XX:CC 
-LAN = XX:XX:XX:XX:XX:XX +LAN = XX:XX:XX:XX:XX:CD 
-WLAN0 = XX:XX:XX:XX:XX:XX +WLAN0 = XX:XX:XX:XX:XX:CE 
-WLAN1 = XX:XX:XX:XX:XX:XX +WLAN1 = XX:XX:XX:XX:XX:CF 
-WLAN2 = XX:XX:XX:XX:XX:XX +WLAN2 = XX:XX:XX:XX:XX:D0 
-WLAN3 = XX:XX:XX:XX:XX:XX +WLAN3 = XX:XX:XX:XX:XX:D1 
-WLAN4 = XX:XX:XX:XX:XX:XX +WLAN4 = XX:XX:XX:XX:XX:D2 
-WLAN5 = XX:XX:XX:XX:XX:XX +WLAN5 = XX:XX:XX:XX:XX:D3 
-WLAN6 = XX:XX:XX:XX:XX:XX +WLAN6 = XX:XX:XX:XX:XX:D4 
-WLAN7 = XX:XX:XX:XX:XX:XX+WLAN7 = XX:XX:XX:XX:XX:D5
 BEID STATUS  : 0 , STATUS OK! BEID STATUS  : 0 , STATUS OK!
 [vlan] vlan for M30 - v1.1.9 [vlan] vlan for M30 - v1.1.9
 [vlan] vlan Start [vlan] vlan Start
 [vlan] Complete Cmd [vlan] Complete Cmd
-WAN = XX:XX:XX:XX:XX:XX +WAN = XX:XX:XX:XX:XX:CC 
-LAN = XX:XX:XX:XX:XX:XX +LAN = XX:XX:XX:XX:XX:CD 
-WLAN0 = XX:XX:XX:XX:XX:XX +WLAN0 = XX:XX:XX:XX:XX:CE 
-WLAN1 = XX:XX:XX:XX:XX:XX +WLAN1 = XX:XX:XX:XX:XX:CF 
-WLAN2 = XX:XX:XX:XX:XX:XX +WLAN2 = XX:XX:XX:XX:XX:D0 
-WLAN3 = XX:XX:XX:XX:XX:XX +WLAN3 = XX:XX:XX:XX:XX:D1 
-WLAN4 = XX:XX:XX:XX:XX:XX +WLAN4 = XX:XX:XX:XX:XX:D2 
-WLAN5 = XX:XX:XX:XX:XX:XX +WLAN5 = XX:XX:XX:XX:XX:D3 
-WLAN6 = XX:XX:XX:XX:XX:XX +WLAN6 = XX:XX:XX:XX:XX:D4 
-WLAN7 = XX:XX:XX:XX:XX:XX+WLAN7 = XX:XX:XX:XX:XX:D5
 BEID STATUS  : 0 , STATUS OK! BEID STATUS  : 0 , STATUS OK!
 [vlan] Interface br0 Have Down [vlan] Interface br0 Have Down
Line 1122: Line 1130:
 tion = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 tion = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99
 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1
-[vlan] i = 0 wanMac = xxxxxxxxxxxx+[vlan] i = 0 wanMac = xxxxxxxxxxcc
 [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 portMac = 000000000000
 [vlan] i = 0 wanInterface = eth1 [vlan] i = 0 wanInterface = eth1
Line 1129: Line 1137:
 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0
 [vlan] i = 1 lanIndex = 0 [vlan] i = 1 lanIndex = 0
-[vlan] i = 1 lanMac = xxxxxxxxxxxx+[vlan] i = 1 lanMac = xxxxxxxxxxcd
 [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portMac = 000000000000
 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 portInterface = eth0
Line 1747: Line 1755:
 [   25.695208] phy_freq_adjust : no prim_ch value for adjust! [   25.695208] phy_freq_adjust : no prim_ch value for adjust!
 [   25.700692] WiFi@C23L1,operate_loader_phy() 397: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi] [   25.700692] WiFi@C23L1,operate_loader_phy() 397: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi]
-[   25.714118] wdev_attr_update(): wdevId0 = XX:XX:XX:XX:XX:XX+[   25.714118] wdev_attr_update(): wdevId0 = XX:XX:XX:XX:XX:ce
 [   25.719739] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0 [   25.719739] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0
 [   25.728738] WiFi@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=0 [   25.728738] WiFi@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=0
Line 1905: Line 1913:
 [   39.024792] phy_freq_adjust : no prim_ch value for adjust! [   39.024792] phy_freq_adjust : no prim_ch value for adjust!
 [   39.030274] 7981@C23L1,operate_loader_phy() 397: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi] [   39.030274] 7981@C23L1,operate_loader_phy() 397: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi]
-[   39.043691] wdev_attr_update(): wdevId3 = XX:XX:XX:XX:XX:XX+[   39.043691] wdev_attr_update(): wdevId3 = XX:XX:XX:XX:XX:d1
 [   39.049287] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band1 group_idx[3]=4, bw_grp=16 omac=0 [   39.049287] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band1 group_idx[3]=4, bw_grp=16 omac=0
 [   39.058298] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=3 [   39.058298] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=3
Line 1993: Line 2001:
 [   43.201511] 7981@C12L1,EDCCAInit() 20989: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0 [   43.201511] 7981@C12L1,EDCCAInit() 20989: EDCCA compensation: uni_compensation=0, bw_compensation=0, final compensation=0
 [   43.212709] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi] [   43.212709] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x150 [mt_wifi]
-[   43.220737] wdev_attr_update(): wdevId4 = XX:XX:XX:XX:XX:XX+[   43.220737] wdev_attr_update(): wdevId4 = XX:XX:XX:XX:XX:d2
 [   43.226332] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band1 group_idx[4]=25, bw_grp=16 omac=17 [   43.226332] WiFi@C12L1,wifi_sys_open() 902: wifi_sys_open():band1 group_idx[4]=25, bw_grp=16 omac=17
 [   43.235495] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=4 [   43.235495] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=4
Line 2086: Line 2094:
 [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99
 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1
-[vlan] i = 0 wanMac = xxxxxxxxxxxx+[vlan] i = 0 wanMac = xxxxxxxxxxcc
 [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 portMac = 000000000000
 [vlan] i = 0 wanInterface = eth1 [vlan] i = 0 wanInterface = eth1
Line 2093: Line 2101:
 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0
 [vlan] i = 1 lanIndex = 0 [vlan] i = 1 lanIndex = 0
-[vlan] i = 1 lanMac = xxxxxxxxxxxx+[vlan] i = 1 lanMac = xxxxxxxxxxcd
 [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portMac = 000000000000
 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 portInterface = eth0
Line 2099: Line 2107:
 [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1 [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1
 [vlan] i = 2 lanIndex = 1 [vlan] i = 2 lanIndex = 1
-[vlan] i = 2 lanMac = xxxxxxxxxxxx+[vlan] i = 2 lanMac = ca787deba0cd
 [vlan] i = 2 portMac = 000000000000 [vlan] i = 2 portMac = 000000000000
 [vlan] i = 2 portInterface = eth0 [vlan] i = 2 portInterface = eth0
Line 2105: Line 2113:
 [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2
 [vlan] i = 3 lanIndex = 2 [vlan] i = 3 lanIndex = 2
-[vlan] i = 3 lanMac = xxxxxxxxxxxx+[vlan] i = 3 lanMac = ce787deba0cd
 [vlan] i = 3 portMac = 000000000000 [vlan] i = 3 portMac = 000000000000
 [vlan] i = 3 portInterface = eth0 [vlan] i = 3 portInterface = eth0
Line 2111: Line 2119:
 [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3 [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3
 [vlan] i = 4 lanIndex = 3 [vlan] i = 4 lanIndex = 3
-[vlan] i = 4 lanMac = xxxxxxxxxxxx+[vlan] i = 4 lanMac = c2787deba0cd
 [vlan] i = 4 portMac = 000000000000 [vlan] i = 4 portMac = 000000000000
 [vlan] i = 4 portInterface = eth0 [vlan] i = 4 portInterface = eth0
Line 2131: Line 2139:
 [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99
 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1
-[vlan] i = 0 wanMac = xxxxxxxxxxxx+[vlan] i = 0 wanMac = xxxxxxxxxxcc
 [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 portMac = 000000000000
 [vlan] i = 0 wanInterface = eth1 [vlan] i = 0 wanInterface = eth1
Line 2138: Line 2146:
 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0
 [vlan] i = 1 lanIndex = 0 [vlan] i = 1 lanIndex = 0
-[vlan] i = 1 lanMac = xxxxxxxxxxxx+[vlan] i = 1 lanMac = xxxxxxxxxxcd
 [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portMac = 000000000000
 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 portInterface = eth0
Line 2144: Line 2152:
 [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1 [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1
 [vlan] i = 2 lanIndex = 1 [vlan] i = 2 lanIndex = 1
-[vlan] i = 2 lanMac = xxxxxxxxxxxx+[vlan] i = 2 lanMac = ca787deba0cd
 [vlan] i = 2 portMac = 000000000000 [vlan] i = 2 portMac = 000000000000
 [vlan] i = 2 portInterface = eth0 [vlan] i = 2 portInterface = eth0
Line 2150: Line 2158:
 [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2
 [vlan] i = 3 lanIndex = 2 [vlan] i = 3 lanIndex = 2
-[vlan] i = 3 lanMac = xxxxxxxxxxxx+[vlan] i = 3 lanMac = ce787deba0cd
 [vlan] i = 3 portMac = 000000000000 [vlan] i = 3 portMac = 000000000000
 [vlan] i = 3 portInterface = eth0 [vlan] i = 3 portInterface = eth0
Line 2156: Line 2164:
 [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3 [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3
 [vlan] i = 4 lanIndex = 3 [vlan] i = 4 lanIndex = 3
-[vlan] i = 4 lanMac = xxxxxxxxxxxx+[vlan] i = 4 lanMac = c2787deba0cd
 [vlan] i = 4 portMac = 000000000000 [vlan] i = 4 portMac = 000000000000
 [vlan] i = 4 portInterface = eth0 [vlan] i = 4 portInterface = eth0
Line 2241: Line 2249:
 RTNETLINK answers: Address not available RTNETLINK answers: Address not available
 ## Lunching system normally completed! ## ## Lunching system normally completed! ##
-+</nowiki>
 </WRAP>\\ </WRAP>\\
  
 ==== OpenWrt bootlog ==== ==== OpenWrt bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING</nowiki>+<nowiki>[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] 
 +[    0.000000] Linux version 6.6.41 (roland@Linux) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26971-66177c081f) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Fri Jul 26 11:41:25 2024 
 +[    0.000000] Machine model: D-Link AQUILA PRO AI M30 A1 
 +[    0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options ''
 +[    0.000000] printk: bootconsole [uart8250] enabled 
 +[    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000 
 +[    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000 
 +[    0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000 
 +[    0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000 
 +[    0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000 
 +[    0.000000] Zone ranges: 
 +[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff] 
 +[    0.000000]   DMA32    empty 
 +[    0.000000]   Normal   empty 
 +[    0.000000] Movable zone start for each node 
 +[    0.000000] Early memory node ranges 
 +[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff] 
 +[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff] 
 +[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff] 
 +[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff] 
 +[    0.000000]   node   0: [mem 0x0000000048000000-0x000000005fffffff] 
 +[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] 
 +[    0.000000] psci: probing for conduit method from DT. 
 +[    0.000000] psci: PSCIv1.1 detected in firmware. 
 +[    0.000000] psci: Using standard PSCI v0.2 function IDs 
 +[    0.000000] psci: MIGRATE_INFO_TYPE not supported. 
 +[    0.000000] psci: SMC Calling Convention v1.2 
 +[    0.000000] percpu: Embedded 18 pages/cpu s34600 r8192 d30936 u73728 
 +[    0.000000] pcpu-alloc: s34600 r8192 d30936 u73728 alloc=18*4096 
 +[    0.000000] pcpu-alloc: [0] 0 [0] 1  
 +[    0.000000] Detected VIPT I-cache on CPU0 
 +[    0.000000] CPU features: detected: GIC system register CPU interface 
 +[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration 
 +[    0.000000] alternatives: applying boot alternatives 
 +[    0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 bootpart=ubi0 
 +[    0.000000] Unknown kernel command line parameters "bootpart=ubi0", will be passed to user space. 
 +[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) 
 +[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) 
 +[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024 
 +[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off 
 +[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB 
 +[    0.000000] software IO TLB: area num 2. 
 +[    0.000000] software IO TLB: mapped [mem 0x000000005f540000-0x000000005f5c0000] (0MB) 
 +[    0.000000] Memory: 496904K/524288K available (8512K kernel code, 894K rwdata, 2504K rodata, 384K init, 287K bss, 27384K reserved, 0K cma-reserved) 
 +[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 
 +[    0.000000] rcu: Hierarchical RCU implementation. 
 +[    0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. 
 +[    0.000000] Tracing variant of Tasks RCU enabled. 
 +[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. 
 +[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 
 +[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 
 +[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode 
 +[    0.000000] GICv3: 640 SPIs implemented 
 +[    0.000000] GICv3: 0 Extended SPIs implemented 
 +[    0.000000] Root IRQ handler: gic_handle_irq 
 +[    0.000000] GICv3: GICv3 features: 16 PPIs 
 +[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 
 +[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. 
 +[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). 
 +[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns 
 +[    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns 
 +[    0.008123] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) 
 +[    0.018533] pid_max: default: 32768 minimum: 301 
 +[    0.026077] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) 
 +[    0.033431] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) 
 +[    0.043276] cacheinfo: Unable to detect cache hierarchy for CPU 0 
 +[    0.049933] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. 
 +[    0.057689] rcu: Hierarchical SRCU implementation. 
 +[    0.062516] rcu: Max phase no-delay instances is 1000. 
 +[    0.068154] smp: Bringing up secondary CPUs ... 
 +[    0.073083] Detected VIPT I-cache on CPU1 
 +[    0.073127] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 
 +[    0.073154] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] 
 +[    0.073218] smp: Brought up 1 node, 2 CPUs 
 +[    0.094829] SMP: Total of 2 processors activated. 
 +[    0.099551] CPU features: detected: 32-bit EL0 Support 
 +[    0.104709] CPU features: detected: CRC32 instructions 
 +[    0.109898] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching 
 +[    0.118288] CPU: All CPU(s) started at EL2 
 +[    0.122401] alternatives: applying system-wide alternatives 
 +[    0.131412] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 
 +[    0.141318] futex hash table entries: 512 (order: 3, 32768 bytes, linear) 
 +[    0.149385] pinctrl core: initialized pinctrl subsystem 
 +[    0.155479] NET: Registered PF_NETLINK/PF_ROUTE protocol family 
 +[    0.162011] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations 
 +[    0.169146] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations 
 +[    0.176944] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations 
 +[    0.185261] thermal_sys: Registered thermal governor 'fair_share' 
 +[    0.185266] thermal_sys: Registered thermal governor 'bang_bang' 
 +[    0.191386] thermal_sys: Registered thermal governor 'step_wise' 
 +[    0.197429] thermal_sys: Registered thermal governor 'user_space' 
 +[    0.203546] ASID allocator initialised with 65536 entries 
 +[    0.216098] pstore: Using crash dump compression: deflate 
 +[    0.221534] pstore: Registered ramoops as persistent store backend 
 +[    0.227740] ramoops: using 0x10000@0x42ff0000, ecc: 0 
 +[    0.239638] Modules: 29584 pages in range for non-PLT usage 
 +[    0.239648] Modules: 521104 pages in range for PLT usage 
 +[    0.246369] cryptd: max_cpu_qlen set to 1000 
 +[    0.258135] SCSI subsystem initialized 
 +[    0.262056] libata version 3.00 loaded. 
 +[    0.267415] clocksource: Switched to clocksource arch_sys_counter 
 +[    0.275854] NET: Registered PF_INET protocol family 
 +[    0.280918] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) 
 +[    0.289386] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) 
 +[    0.297797] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) 
 +[    0.305582] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) 
 +[    0.313393] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) 
 +[    0.320744] TCP: Hash tables configured (established 4096 bind 4096) 
 +[    0.327206] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) 
 +[    0.333796] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) 
 +[    0.341020] NET: Registered PF_UNIX/PF_LOCAL protocol family 
 +[    0.346727] PCI: CLS 0 bytes, default 64 
 +[    0.351972] workingset: timestamp_bits=46 max_order=17 bucket_order=0 
 +[    0.363213] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    0.369091] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.422037] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled 
 +[    0.429687] printk: console [ttyS0] disabled 
 +[    0.454350] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2 
 +[    0.463577] printk: console [ttyS0] enabled 
 +[    0.471953] printk: bootconsole [uart8250] disabled 
 +[    0.486315] loop: module loaded 
 +[    0.491384] spi-nand spi0.0: Macronix SPI NAND was found. 
 +[    0.496783] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 
 +[    0.505444] Signature found at block 1023 [0x07fe0000] 
 +[    0.510600] NMBM management region starts at block 960 [0x07800000] 
 +[    0.517853] First info table with writecount 0 found in block 960 
 +[    0.526151] Second info table with writecount 0 found in block 963 
 +[    0.532341] NMBM has been successfully attached 
 +[    0.537170] 10 fixed-partitions partitions found on MTD device spi0.0 
 +[    0.543635] Creating 10 MTD partitions on "spi0.0": 
 +[    0.548512] 0x000000000000-0x000000100000 : "BL2" 
 +[    0.554158] 0x000000100000-0x000000180000 : "u-boot-env" 
 +[    0.560159] 0x000000180000-0x000000380000 : "Factory" 
 +[    0.566860] 0x000000380000-0x000000580000 : "FIP" 
 +[    0.572950] 0x000000580000-0x000003780000 : "ubi" 
 +[    0.601201] 0x000003780000-0x000006980000 : "ubi1" 
 +[    0.629855] 0x000006980000-0x0000069c0000 : "Odm" 
 +[    0.635356] 0x0000069c0000-0x000006a40000 : "Config1" 
 +[    0.641145] 0x000006a40000-0x000006ac0000 : "Config2" 
 +[    0.646907] 0x000006ac0000-0x0000074c0000 : "Storage" 
 +[    0.804462] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081480000, irq 75 
 +[    0.814343] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081480000, irq 75 
 +[    0.824052] i2c_dev: i2c /dev entries driver 
 +[    0.830799] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) 
 +[    0.839801] NET: Registered PF_INET6 protocol family 
 +[    0.845738] Segment Routing with IPv6 
 +[    0.849449] In-situ OAM (IOAM) with IPv6 
 +[    0.853406] NET: Registered PF_PACKET protocol family 
 +[    0.858647] 8021q: 802.1Q VLAN Support v1.8 
 +[    0.927279] mt7530-mdio mdio-bus:1f: no interrupt support 
 +[    0.948363] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode 
 +[    0.957341] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx 
 +[    0.966294] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=POLL) 
 +[    0.986810] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=POLL) 
 +[    1.007088] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=POLL) 
 +[    1.027373] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=POLL) 
 +[    1.038967] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode 
 +[    1.045705] DSA: tree 0 setup 
 +[    1.049078] UBI: auto-attach mtd4 
 +[    1.052399] ubi0: default fastmap pool size: 20 
 +[    1.056918] ubi0: default fastmap WL pool size: 10 
 +[    1.061716] ubi0: attaching mtd4 
 +[    1.203297] ubi0: scanning is finished 
 +[    1.211301] ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 17, need 19 
 +[    1.221797] ubi0: attached mtd4 (name "ubi", size 50 MiB) 
 +[    1.227200] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes 
 +[    1.234077] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 
 +[    1.240858] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 
 +[    1.247811] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0 
 +[    1.253804] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 
 +[    1.261021] ubi0: max/mean erase counter: 104/71, WL threshold: 4096, image sequence number: 1841881750 
 +[    1.270403] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 17 
 +[    1.279621] ubi0: background thread "ubi_bgt0d" started, PID 560 
 +[    1.280973] block ubiblock0_1: created from ubi0:1(rootfs) 
 +[    1.291109] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem 
 +[    1.298161] clk: Disabling unused clocks 
 +[    1.306832] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. 
 +[    1.314135] Freeing unused kernel memory: 384K 
 +[    1.318655] Run /sbin/init as init process 
 +[    1.322741]   with arguments: 
 +[    1.325694]     /sbin/init 
 +[    1.328399]   with environment: 
 +[    1.331526]     HOME=/ 
 +[    1.333873]     TERM=linux 
 +[    1.336567]     bootpart=ubi0 
 +[    1.519806] init: Console is alive 
 +[    1.523349] init: - watchdog - 
 +[    1.850358] kmodloader: loading kernel modules from /etc/modules-boot.d/
 +[    1.876160] gpio_button_hotplug: loading out-of-tree module taints kernel. 
 +[    1.885989] Enter gca230718_probe for device address 64 
 +[    1.891272] Creating LED for node led: reg=0 
 +[    1.895611] Creating LED for node led: reg=1 
 +[    1.899961] Creating LED for node led: reg=2 
 +[    1.904288] Creating LED for node led: reg=3 
 +[    1.914541] kmodloader: done loading kernel modules from /etc/modules-boot.d/
 +[    1.931753] init: - preinit - 
 +[    2.256994] mtk_soc_eth 15100000.ethernet internet: renamed from eth1 
 +[    2.291008] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode 
 +[    2.300804] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx 
 +[    2.320345] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode 
 +[    4.443726] UBIFS (ubi0:2): default file-system created 
 +[    4.450681] UBIFS (ubi0:2): Mounting in unauthenticated mode 
 +[    4.456435] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 696 
 +[    4.497169] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" 
 +[    4.505028] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes 
 +[    4.514932] UBIFS (ubi0:2): FS size: 37711872 bytes (35 MiB, 297 LEBs), max 307 LEBs, journal size 1904640 bytes (1 MiB, 15 LEBs) 
 +[    4.526574] UBIFS (ubi0:2): reserved for root: 1781224 bytes (1739 KiB) 
 +[    4.533179] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 4F25D334-58BF-46CB-A02D-D1CA05EF3B5D, small LPT model 
 +[    4.545768] mount_root: overlay filesystem has not been fully initialized yet 
 +[    4.553198] mount_root: switching to ubifs overlay 
 +[    4.560239] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. 
 +[    4.571945] urandom-seed: Seed file not found (/etc/urandom.seed) 
 +[    4.620187] random: procd: uninitialized urandom read (4 bytes read) 
 +[    4.624006] procd: - early - 
 +[    4.629657] procd: - watchdog - 
 +[    5.187847] procd: - watchdog - 
 +[    5.191409] procd: - ubus - 
 +[    5.887424] random: crng init done 
 +[    5.894200] procd: - init - 
 +[    6.218523] kmodloader: loading kernel modules from /etc/modules.d/
 +[    6.240741] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/
 +[    6.258398] Loading modules backported from Linux version v6.9.9-0-g28fdf4518483 
 +[    6.265790] Backport generated by backports.git v6.1.97-1-29-gf1d24a3683b2 
 +[    6.416501] urngd: v1.0.2 started. 
 +[    6.607806] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221208201745a 
 +[    6.607806]  
 +[    6.774206] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221208201806 
 +[    6.867772] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221208202048 
 +[    6.959198] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0' 
 +[    6.967641] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1' 
 +[    7.050563] mtdblock: MTD device 'Odm' is NAND, please consider using UBI block devices instead. 
 +[    7.112881] mtdblock: MTD device 'Odm' is NAND, please consider using UBI block devices instead. 
 +[    9.199535] PPP generic driver version 2.4.2 
 +[    9.204532] NET: Registered PF_PPPOX protocol family 
 +[    9.212296] kmodloader: done loading kernel modules from /etc/modules.d/
 +[   14.548016] mtk_soc_eth 15100000.ethernet eth0: Link is Down 
 +[   14.569472] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode 
 +[   14.578277] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx 
 +[   14.593896] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode 
 +[   14.602974] br-lan: port 1(lan1) entered blocking state 
 +[   14.608267] br-lan: port 1(lan1) entered disabled state 
 +[   14.613518] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode 
 +[   14.619803] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode 
 +[   14.629492] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode 
 +[   14.656929] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode 
 +[   14.689000] br-lan: port 2(lan2) entered blocking state 
 +[   14.694234] br-lan: port 2(lan2) entered disabled state 
 +[   14.699573] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode 
 +[   14.707805] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode 
 +[   14.723752] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode 
 +[   14.734875] br-lan: port 3(lan3) entered blocking state 
 +[   14.740164] br-lan: port 3(lan3) entered disabled state 
 +[   14.745415] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode 
 +[   14.754700] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode 
 +[   14.771957] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode 
 +[   14.783266] br-lan: port 4(lan4) entered blocking state 
 +[   14.788545] br-lan: port 4(lan4) entered disabled state 
 +[   14.793800] mt7530-mdio mdio-bus:1f lan4: entered allmulticast mode 
 +[   14.802268] mt7530-mdio mdio-bus:1f lan4: entered promiscuous mode 
 +[   14.836030] mtk_soc_eth 15100000.ethernet internet: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL) 
 +[   14.845993] mtk_soc_eth 15100000.ethernet internet: configuring for phy/gmii link mode 
 +[   14.856104] mtk_soc_eth 15100000.ethernet internet: Link is Up - 1Gbps/Full - flow control off 
 +[   19.972473] mt7530-mdio mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx 
 +[   19.980461] br-lan: port 4(lan4) entered blocking state 
 +[   19.985680] br-lan: port 4(lan4) entered forwarding state</nowiki>
 </WRAP>\\ </WRAP>\\
  
  • Last modified: 2024/07/27 14:51
  • by rolandomagico