Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:d-link:aquila_pro_ai_m30_a1 [2024/07/21 12:08] – [Opening the case] rolandomagico | toh:d-link:aquila_pro_ai_m30_a1 [2024/07/27 14:45] – [OEM bootlog] rolandomagico | ||
|---|---|---|---|
| Line 121: | Line 121: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME //The instructions below are for Broadcom devices and only serve as an example.//\\ | + | Flashing OpenWrt via OEM web interface is not supported. But there is a recovery web interface which can be used to flash the OpenWrt recovery image: |
| - | **//Remove | + | |
| + | * If OpenWrt is flashed to the second partition, it will not boot. | ||
| + | * Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end. | ||
| + | | ||
| + | * Press the reset button while powering on the device | ||
| + | * Keep the reset button pressed until the LED blinks red | ||
| + | * Open a Chromium based and go to http://192.168.200.1/ (recovery web interface) | ||
| + | * Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-**recovery**.bin | ||
| + | * The recovery web interface always reports successful flashing, even if it fails | ||
| + | * After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored) | ||
| + | * If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt. | ||
| + | * If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are required: | ||
| - | This section deals with | + | === Recovering when OEM firmware < 1.10.02 was installed previously === |
| - | * How you install OpenWrt from a device freshly opened | + | * Start the web recovery interface again and flash the decrypted OEM image. |
| - | * The steps required such as reset to factory defaults if the device has already been configured | + | |
| + | | ||
| - | **Note:** Reset router to factory defaults if it has been previously configured. | + | === Recovering when OEM firmware |
| - | * Browse to ''< | + | |
| - | * Upload .bin file to router | + | |
| - | * Wait for it to reboot | + | |
| - | * Telnet to 192.168.1.1 and set a root password, or browse to ''< | + | |
| </ | </ | ||
| Line 305: | Line 313: | ||
| **Insert photo of PCB with markings for serial port** | **Insert photo of PCB with markings for serial port** | ||
| - | <WRAP BOX> | + | The serial interface can be connected to the 4 pin holes on the side of the board. Pins (from front to rear): |
| - | FIXME //Replace EXAMPLE by real values.// | + | * 3.3V |
| - | </ | + | * RX |
| + | * TX | ||
| + | * GND | ||
| - | ^ Serial connection parameters\\ for D-Link AQUILA PRO AI M30 A1 | EXAMPLE | + | ^ Serial connection parameters\\ for D-Link AQUILA PRO AI M30 A1 | 115200, 8N1, 3.3V | |
| ==== JTAG ==== | ==== JTAG ==== | ||
| Line 328: | Line 338: | ||
| ==== OEM bootlog ==== | ==== OEM bootlog ==== | ||
| <WRAP bootlog> | <WRAP bootlog> | ||
| - | < | + | < |
| + | F0: 102B 0000 | ||
| + | FA: 1040 0000 | ||
| + | FA: 1040 0000 [0200] | ||
| + | F9: 0000 0000 | ||
| + | V0: 0000 0000 [0001] | ||
| + | 00: 0000 0000 | ||
| + | BP: 2400 0041 [0000] | ||
| + | G0: 1190 0000 | ||
| + | EC: 0000 0000 [1000] | ||
| + | T0: 0000 025A [010F] | ||
| + | Jump to BL | ||
| + | |||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | |||
| + | dump toprgu registers data: | ||
| + | 1001c000 | 00000000 0000ffe0 00000000 00000000 | ||
| + | 1001c010 | 00000fff 00000000 00f00000 00000000 | ||
| + | 1001c020 | 00000000 00000000 00000000 00000000 | ||
| + | 1001c030 | 003c0003 003c0003 00000000 00000000 | ||
| + | 1001c040 | 00000000 00000000 00000000 00000000 | ||
| + | 1001c050 | 00000000 00000000 00000000 00000000 | ||
| + | 1001c060 | 00000000 00000000 00000000 00000000 | ||
| + | 1001c070 | 00000000 00000000 00000000 00000000 | ||
| + | 1001c080 | 00000000 00000000 00000000 00000000 | ||
| + | |||
| + | dump drm registers data: | ||
| + | 1001d000 | 00000000 00000000 00000000 00000000 | ||
| + | 1001d010 | 00000000 00000000 00000000 00000000 | ||
| + | 1001d020 | 00000000 00000000 00000000 00000000 | ||
| + | 1001d030 | 00a083f1 000003ff 00100000 00000000 | ||
| + | 1001d040 | 00000000 00000000 00020303 000000ff | ||
| + | 1001d050 | 00000000 00000000 00000000 00000000 | ||
| + | 1001d060 | 00000002 00000000 00000000 00000000 | ||
| + | drm: 500 = 0x8 | ||
| + | [DDR Reserve] ddr reserve mode not be enabled yet | ||
| + | DDR RESERVE Success 0 | ||
| + | [EMI] ComboMCP not ready, using default setting | ||
| + | BYTE_swap: | ||
| + | BYTE_swap: | ||
| + | Window Sum 568, worse bit 2, min window 68 | ||
| + | Window Sum 576, worse bit 8, min window 72 | ||
| + | Window Sum 326, worse bit 3, min window 36 | ||
| + | Window Sum 320, worse bit 9, min window 36 | ||
| + | Window Sum 346, worse bit 2, min window 40 | ||
| + | Window Sum 340, worse bit 9, min window 40 | ||
| + | Window Sum 362, worse bit 3, min window 42 | ||
| + | Window Sum 348, worse bit 9, min window 42 | ||
| + | Window Sum 378, worse bit 3, min window 44 | ||
| + | Window Sum 368, worse bit 9, min window 44 | ||
| + | Window Sum 392, worse bit 2, min window 46 | ||
| + | Window Sum 380, worse bit 9, min window 46 | ||
| + | Window Sum 404, worse bit 6, min window 48 | ||
| + | Window Sum 402, worse bit 9, min window 48 | ||
| + | Window Sum 418, worse bit 2, min window 50 | ||
| + | Window Sum 406, worse bit 15, min window 48 | ||
| + | Window Sum 426, worse bit 6, min window 50 | ||
| + | Window Sum 420, worse bit 14, min window 50 | ||
| + | Window Sum 448, worse bit 3, min window 54 | ||
| + | Window Sum 434, worse bit 15, min window 52 | ||
| + | Window Sum 452, worse bit 2, min window 54 | ||
| + | Window Sum 444, worse bit 9, min window 54 | ||
| + | Window Sum 462, worse bit 4, min window 54 | ||
| + | Window Sum 454, worse bit 8, min window 56 | ||
| + | Window Sum 474, worse bit 6, min window 56 | ||
| + | Window Sum 464, worse bit 9, min window 56 | ||
| + | Window Sum 478, worse bit 3, min window 58 | ||
| + | Window Sum 468, worse bit 14, min window 56 | ||
| + | Window Sum 482, worse bit 4, min window 58 | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | NOTICE: | ||
| + | |||
| + | |||
| + | U-Boot 2022.07-rc3-g091472d6-dirty (Aug 04 2023 - 08:42:13 +0000) | ||
| + | |||
| + | CPU: | ||
| + | Model: mt7981-rfb | ||
| + | DRAM: 512 MiB | ||
| + | Core: 38 devices, 16 uclasses, devicetree: embed | ||
| + | |||
| + | Initializing NMBM(mt7981_rfb) ... | ||
| + | spi-nand: spi_nand spi_nand@0: Macronix SPI NAND was found. | ||
| + | spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 | ||
| + | Could not find a valid device for nmbm0 | ||
| + | Signature found at block 1023 [0x07fe0000] | ||
| + | First info table with writecount 2 found in block 960 | ||
| + | Second info table with writecount 2 found in block 963 | ||
| + | NMBM has been successfully attached | ||
| + | |||
| + | Loading Environment from MTD... OK | ||
| + | In: serial@11002000 | ||
| + | Out: | ||
| + | Err: | ||
| + | Net: eth0: ethernet@15100000 | ||
| + | Setting bus to 0 | ||
| + | Error writing the chip: -121 | ||
| + | Error writing the chip: -121 | ||
| + | Error writing the chip: -121 | ||
| + | gpio: pin 0 (gpio 0) value is 1 | ||
| + | |||
| + | *** U-Boot Boot Menu *** | ||
| + | |||
| + | 1. Startup system (Default) | ||
| + | 2. Upgrade firmware | ||
| + | 3. Upgrade ATF BL2 | ||
| + | 4. Upgrade ATF FIP | ||
| + | 5. Http Upgrade | ||
| + | 6. Upgrade single image | ||
| + | 7. Load image | ||
| + | 0. U-Boot console | ||
| + | |||
| + | |||
| + | Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit | ||
| + | aup_command:: | ||
| + | aup_start | ||
| + | start load_p_section | ||
| + | Reading from 0x0 to 0x5ffabda8, size 0x10 ... OK | ||
| + | load_section: | ||
| + | Reading from 0x0 to 0x5ffabda8, size 0x14cb ... OK | ||
| + | load_section: | ||
| + | csxf-> | ||
| + | csxf-> | ||
| + | csxf-> | ||
| + | csxf-> | ||
| + | csxf-> | ||
| + | check p section: ok | ||
| + | load P section success | ||
| + | | ||
| + | sys info PV 01 | ||
| + | model name: (M30) | ||
| + | ecn no: (200909100001) | ||
| + | beid rule: 190A | ||
| + | beid mac: XX: | ||
| + | | ||
| + | aup_start Using ethernet@15100000 device | ||
| + | mcast upgrade timeout. | ||
| + | ubi_boot_image: | ||
| + | ubi0: attaching mtd6 | ||
| + | ubi0: scanning is finished | ||
| + | ubi0: attached mtd6 (name " | ||
| + | ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | ||
| + | ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | ||
| + | ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 | ||
| + | ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0 | ||
| + | ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 | ||
| + | ubi0: max/mean erase counter: 102/62, WL threshold: 4096, image sequence number: 1571737675 | ||
| + | ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 19 | ||
| + | Reading from volume ' | ||
| + | ## Loading kernel from FIT Image at 46000000 ... | ||
| + | Using ' | ||
| + | | ||
| + | | ||
| + | | ||
| + | | ||
| + | Data Start: | ||
| + | Data Size: 3893088 Bytes = 3.7 MiB | ||
| + | | ||
| + | | ||
| + | Load Address: 0x48080000 | ||
| + | Entry Point: | ||
| + | Hash algo: crc32 | ||
| + | Hash value: | ||
| + | Hash algo: sha1 | ||
| + | Hash value: | ||
| + | | ||
| + | ## Loading fdt from FIT Image at 46000000 ... | ||
| + | Using ' | ||
| + | | ||
| + | | ||
| + | | ||
| + | | ||
| + | Data Start: | ||
| + | Data Size: 18264 Bytes = 17.8 KiB | ||
| + | | ||
| + | Hash algo: crc32 | ||
| + | Hash value: | ||
| + | Hash algo: sha1 | ||
| + | Hash value: | ||
| + | | ||
| + | | ||
| + | | ||
| + | | ||
| + | fdt_chosen: | ||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] | ||
| + | [ 0.000000] Linux version 5.4.171 (oe-user@oe-host) (gcc version 10.2.0 (GCC)) #1 SMP Fri Feb 24 10:07:55 UTC 2023 | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: search " | ||
| + | [ 0.000000] OF: fdt: Looking for initrd properties... | ||
| + | [ 0.000000] OF: fdt: Command line is: console=ttyS0, | ||
| + | [ 0.000000] OF: fdt: dt_root_size_cells = 2 | ||
| + | [ 0.000000] OF: fdt: dt_root_addr_cells = 2 | ||
| + | [ 0.000000] OF: fdt: memory scan node memory, reg size 16, | ||
| + | [ 0.000000] OF: fdt: - 40000000 , 20000000 | ||
| + | [ 0.000000] Machine model: MediaTek MT7981 RFB | ||
| + | [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '' | ||
| + | [ 0.000000] printk: bootconsole [uart8250] enabled | ||
| + | [ 0.000000] OF: fdt: Reserved memory: reserved region for node ' | ||
| + | [ 0.000000] OF: fdt: Reserved memory: reserved region for node ' | ||
| + | [ 0.000000] OF: fdt: Reserved memory: reserved region for node ' | ||
| + | [ 0.000000] OF: fdt: Reserved memory: reserved region for node ' | ||
| + | [ 0.000000] OF: fdt: -> unflatten_device_tree() | ||
| + | [ 0.000000] OF: fdt: Unflattening device tree: | ||
| + | [ 0.000000] OF: fdt: magic: d00dfeed | ||
| + | [ 0.000000] OF: fdt: size: 00005000 | ||
| + | [ 0.000000] OF: fdt: version: 00000011 | ||
| + | [ 0.000000] OF: fdt: size is 78652, allocating... | ||
| + | [ 0.000000] OF: fdt: | ||
| + | [ 0.000000] OF: fdt: fixed up name for -> | ||
| + | [ 0.000000] OF: fdt: fixed up name for cpus -> cpus | ||
| + | [ 0.000000] OF: fdt: fixed up name for cpu@0 -> cpu | ||
| + | [ 0.000000] OF: fdt: fixed up name for cpu@1 -> cpu | ||
| + | [ 0.000000] OF: fdt: fixed up name for pwm@10048000 -> pwm | ||
| + | [ 0.000000] OF: fdt: fixed up name for thermal-zones -> thermal-zones | ||
| + | [ 0.000000] OF: fdt: fixed up name for cpu-thermal -> cpu-thermal | ||
| + | [ 0.000000] OF: fdt: fixed up name for thermal@1100c800 -> thermal | ||
| + | [ 0.000000] OF: fdt: fixed up name for adc@1100d000 -> adc | ||
| + | [ 0.000000] OF: fdt: fixed up name for wed@15010000 -> wed | ||
| + | [ 0.000000] OF: fdt: fixed up name for wdma@15104800 -> wdma | ||
| + | [ 0.000000] OF: fdt: fixed up name for ap2woccif@151A5000 -> ap2woccif | ||
| + | [ 0.000000] OF: fdt: fixed up name for wocpu0_ilm@151E0000 -> wocpu0_ilm | ||
| + | [ 0.000000] OF: fdt: fixed up name for wocpu_dlm@151E8000 -> wocpu_dlm | ||
| + | [ 0.000000] OF: fdt: fixed up name for wocpu_boot@15194000 -> wocpu_boot | ||
| + | [ 0.000000] OF: fdt: fixed up name for reserved-memory -> reserved-memory | ||
| + | [ 0.000000] OF: fdt: fixed up name for secmon@43000000 -> secmon | ||
| + | [ 0.000000] OF: fdt: fixed up name for wmcpu-reserved@47C80000 -> wmcpu-reserved | ||
| + | [ 0.000000] OF: fdt: fixed up name for wocpu0_emi@47D80000 -> wocpu0_emi | ||
| + | [ 0.000000] OF: fdt: fixed up name for wocpu_data@47DC0000 -> wocpu_data | ||
| + | [ 0.000000] OF: fdt: fixed up name for psci -> psci | ||
| + | [ 0.000000] OF: fdt: fixed up name for oscillator@0 -> oscillator | ||
| + | [ 0.000000] OF: fdt: fixed up name for infracfg_ao@10001000 -> infracfg_ao | ||
| + | [ 0.000000] OF: fdt: fixed up name for infracfg@10001040 -> infracfg | ||
| + | [ 0.000000] OF: fdt: fixed up name for topckgen@1001B000 -> topckgen | ||
| + | [ 0.000000] OF: fdt: fixed up name for apmixedsys@1001E000 -> apmixedsys | ||
| + | [ 0.000000] OF: fdt: fixed up name for dummy_system_clk -> dummy_system_clk | ||
| + | [ 0.000000] OF: fdt: fixed up name for dummy_gpt_clk -> dummy_gpt_clk | ||
| + | [ 0.000000] OF: fdt: fixed up name for timer -> timer | ||
| + | [ 0.000000] OF: fdt: fixed up name for watchdog@1001c000 -> watchdog | ||
| + | [ 0.000000] OF: fdt: fixed up name for interrupt-controller@c000000 -> interrupt-controller | ||
| + | [ 0.000000] OF: fdt: fixed up name for trng@1020f000 -> trng | ||
| + | [ 0.000000] OF: fdt: fixed up name for serial@11002000 -> serial | ||
| + | [ 0.000000] OF: fdt: fixed up name for serial@11003000 -> serial | ||
| + | [ 0.000000] OF: fdt: fixed up name for serial@11004000 -> serial | ||
| + | [ 0.000000] OF: fdt: fixed up name for i2c@11007000 -> i2c | ||
| + | [ 0.000000] OF: fdt: fixed up name for wm8960@1a -> wm8960 | ||
| + | [ 0.000000] OF: fdt: fixed up name for pcie@11280000 -> pcie | ||
| + | [ 0.000000] OF: fdt: fixed up name for interrupt-controller -> interrupt-controller | ||
| + | [ 0.000000] OF: fdt: fixed up name for crypto@10320000 -> crypto | ||
| + | [ 0.000000] OF: fdt: fixed up name for pinctrl@11d00000 -> pinctrl | ||
| + | [ 0.000000] OF: fdt: fixed up name for i2c-pins-g0 -> i2c-pins-g0 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for pcm-pins-g0 -> pcm-pins-g0 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for pwm0-pin-g0 -> pwm0-pin-g0 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for pwm1-pin-g0 -> pwm1-pin-g0 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for pwm2-pin -> pwm2-pin | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi0-pins -> spi0-pins | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for conf-pu -> conf-pu | ||
| + | [ 0.000000] OF: fdt: fixed up name for conf-pd -> conf-pd | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi1-pins -> spi1-pins | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for uart1-pins-g1 -> uart1-pins-g1 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for uart2-pins-g1 -> uart2-pins-g1 | ||
| + | [ 0.000000] OF: fdt: fixed up name for mux -> mux | ||
| + | [ 0.000000] OF: fdt: fixed up name for syscon@15000000 -> syscon | ||
| + | [ 0.000000] OF: fdt: fixed up name for reset-controller -> reset-controller | ||
| + | [ 0.000000] OF: fdt: fixed up name for ethernet@15100000 -> ethernet | ||
| + | [ 0.000000] OF: fdt: fixed up name for mac@0 -> mac | ||
| + | [ 0.000000] OF: fdt: fixed up name for fixed-link -> fixed-link | ||
| + | [ 0.000000] OF: fdt: fixed up name for mac@1 -> mac | ||
| + | [ 0.000000] OF: fdt: fixed up name for mdio-bus -> mdio-bus | ||
| + | [ 0.000000] OF: fdt: fixed up name for ethernet-phy@0 -> ethernet-phy | ||
| + | [ 0.000000] OF: fdt: fixed up name for switch@0 -> switch | ||
| + | [ 0.000000] OF: fdt: fixed up name for ports -> ports | ||
| + | [ 0.000000] OF: fdt: fixed up name for port@0 -> port | ||
| + | [ 0.000000] OF: fdt: fixed up name for port@1 -> port | ||
| + | [ 0.000000] OF: fdt: fixed up name for port@2 -> port | ||
| + | [ 0.000000] OF: fdt: fixed up name for port@3 -> port | ||
| + | [ 0.000000] OF: fdt: fixed up name for port@6 -> port | ||
| + | [ 0.000000] OF: fdt: fixed up name for fixed-link -> fixed-link | ||
| + | [ 0.000000] OF: fdt: fixed up name for hnat@15000000 -> hnat | ||
| + | [ 0.000000] OF: fdt: fixed up name for syscon@10060000 -> syscon | ||
| + | [ 0.000000] OF: fdt: fixed up name for syscon@10070000 -> syscon | ||
| + | [ 0.000000] OF: fdt: fixed up name for topmisc@11d10000 -> topmisc | ||
| + | [ 0.000000] OF: fdt: fixed up name for snfi@11005000 -> snfi | ||
| + | [ 0.000000] OF: fdt: fixed up name for mmc@11230000 -> mmc | ||
| + | [ 0.000000] OF: fdt: fixed up name for wbsys@18000000 -> wbsys | ||
| + | [ 0.000000] OF: fdt: fixed up name for wed_pcie@10003000 -> wed_pcie | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi@1100a000 -> spi | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi_nand@0 -> spi_nand | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi@1100b000 -> spi | ||
| + | [ 0.000000] OF: fdt: fixed up name for proslic_spi@0 -> proslic_spi | ||
| + | [ 0.000000] OF: fdt: fixed up name for spi@11009000 -> spi | ||
| + | [ 0.000000] OF: fdt: fixed up name for consys@10000000 -> consys | ||
| + | [ 0.000000] OF: fdt: fixed up name for xhci@11200000 -> xhci | ||
| + | [ 0.000000] OF: fdt: fixed up name for usb-phy@11e10000 -> usb-phy | ||
| + | [ 0.000000] OF: fdt: fixed up name for usb-phy@11e10000 -> usb-phy | ||
| + | [ 0.000000] OF: fdt: fixed up name for usb-phy@11e10700 -> usb-phy | ||
| + | [ 0.000000] OF: fdt: fixed up name for regulator-3p3v -> regulator-3p3v | ||
| + | [ 0.000000] OF: fdt: fixed up name for clkitg -> clkitg | ||
| + | [ 0.000000] OF: fdt: fixed up name for bring-up -> bring-up | ||
| + | [ 0.000000] OF: fdt: fixed up name for efuse@11f20000 -> efuse | ||
| + | [ 0.000000] OF: fdt: fixed up name for calib@274 -> calib | ||
| + | [ 0.000000] OF: fdt: fixed up name for calib@8dc -> calib | ||
| + | [ 0.000000] OF: fdt: fixed up name for audio-controller@11210000 -> audio-controller | ||
| + | [ 0.000000] OF: fdt: fixed up name for ice_debug -> ice_debug | ||
| + | [ 0.000000] OF: fdt: fixed up name for nmbm_spim_nand -> nmbm_spim_nand | ||
| + | [ 0.000000] OF: fdt: fixed up name for partitions -> partitions | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@0 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@100000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@180000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@380000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@580000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@3780000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@6980000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@69c0000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@6a40000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for partition@6ac0000 -> partition | ||
| + | [ 0.000000] OF: fdt: fixed up name for chosen -> chosen | ||
| + | [ 0.000000] OF: fdt: fixed up name for memory -> memory | ||
| + | [ 0.000000] OF: fdt: fixed up name for leds -> leds | ||
| + | [ 0.000000] OF: fdt: fixed up name for power_green -> power_green | ||
| + | [ 0.000000] OF: fdt: fixed up name for power_red -> power_red | ||
| + | [ 0.000000] OF: fdt: fixed up name for wlan_2g_red -> wlan_2g_red | ||
| + | [ 0.000000] OF: fdt: fixed up name for wlan_5g_red -> wlan_5g_red | ||
| + | [ 0.000000] OF: fdt: fixed up name for gpio-keys -> gpio-keys | ||
| + | [ 0.000000] OF: fdt: fixed up name for rst_btn -> rst_btn | ||
| + | [ 0.000000] OF: fdt: fixed up name for wps_btn -> wps_btn | ||
| + | [ 0.000000] OF: fdt: fixed up name for onoff_btn -> onoff_btn | ||
| + | [ 0.000000] OF: fdt: <- unflatten_device_tree() | ||
| + | [ 0.000000] On node 0 totalpages: 130128 | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] psci: probing for conduit method from DT. | ||
| + | [ 0.000000] psci: PSCIv1.1 detected in firmware. | ||
| + | [ 0.000000] psci: Using standard PSCI v0.2 function IDs | ||
| + | [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. | ||
| + | [ 0.000000] psci: SMC Calling Convention v1.0 | ||
| + | [ 0.000000] percpu: Embedded 20 pages/cpu s43864 r8192 d29864 u81920 | ||
| + | [ 0.000000] pcpu-alloc: s43864 r8192 d29864 u81920 alloc=20*4096 | ||
| + | [ 0.000000] pcpu-alloc: [0] 0 [0] 1 | ||
| + | [ 0.000000] Detected VIPT I-cache on CPU0 | ||
| + | [ 0.000000] CPU features: detected: GIC system register CPU interface | ||
| + | [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration | ||
| + | [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128080 | ||
| + | [ 0.000000] Kernel command line: console=ttyS0, | ||
| + | [ 0.000000] start rootfs@ubi | ||
| + | [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) | ||
| + | [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) | ||
| + | [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | ||
| + | [ 0.000000] Memory: 490496K/ | ||
| + | [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, | ||
| + | [ 0.000000] rcu: Hierarchical RCU implementation. | ||
| + | [ 0.000000] rcu: | ||
| + | [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. | ||
| + | [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 | ||
| + | [ 0.000000] GICv3: GIC: Using split EOI/ | ||
| + | [ 0.000000] GICv3: 640 SPIs implemented | ||
| + | [ 0.000000] GICv3: 0 Extended SPIs implemented | ||
| + | [ 0.000000] GICv3: Distributor has no Range Selector support | ||
| + | [ 0.000000] GICv3: 16 PPIs implemented | ||
| + | [ 0.000000] GICv3: no VLPI support, no direct LPI support | ||
| + | [ 0.000000] GICv3: CPU0: found redistributor 0 region 0: | ||
| + | [ 0.000000] random: get_random_bytes called from start_kernel+0x334/ | ||
| + | [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). | ||
| + | [ 0.000000] clocksource: | ||
| + | [ 0.000003] sched_clock: | ||
| + | [ 0.008182] Console: colour dummy device 80x25 | ||
| + | [ 0.012666] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000) | ||
| + | [ 0.022985] pid_max: default: 32768 minimum: 301 | ||
| + | [ 0.027697] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.035047] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.043631] ASID allocator initialised with 65536 entries | ||
| + | [ 0.049124] rcu: Hierarchical SRCU implementation. | ||
| + | [ 0.054202] smp: Bringing up secondary CPUs ... | ||
| + | [ 0.059029] Detected VIPT I-cache on CPU1 | ||
| + | [ 0.059048] GICv3: CPU1: found redistributor 1 region 0: | ||
| + | [ 0.059069] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | ||
| + | [ 0.059128] smp: Brought up 1 node, 2 CPUs | ||
| + | [ 0.080739] SMP: Total of 2 processors activated. | ||
| + | [ 0.085464] CPU features: detected: 32-bit EL0 Support | ||
| + | [ 0.090626] CPU features: detected: CRC32 instructions | ||
| + | [ 0.095889] CPU: All CPU(s) started at EL2 | ||
| + | [ 0.100010] alternatives: | ||
| + | [ 0.104940] devtmpfs: initialized | ||
| + | [ 0.110244] clocksource: | ||
| + | [ 0.120060] futex hash table entries: 512 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.126950] pinctrl core: initialized pinctrl subsystem | ||
| + | [ 0.132707] NET: Registered protocol family 16 | ||
| + | [ 0.137395] DMA: preallocated 256 KiB pool for atomic allocations | ||
| + | [ 0.157595] cryptd: max_cpu_qlen set to 1000 | ||
| + | [ 0.163401] iommu: Default domain type: Translated | ||
| + | [ 0.168476] SCSI subsystem initialized | ||
| + | [ 0.173003] libata version 3.00 loaded. | ||
| + | [ 0.177110] usbcore: registered new interface driver usbfs | ||
| + | [ 0.182665] usbcore: registered new interface driver hub | ||
| + | [ 0.188031] usbcore: registered new device driver usb | ||
| + | [ 0.194106] rbus 18000000.wbsys: | ||
| + | [ 0.200069] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff] | ||
| + | [ 0.206980] pci_bus 0000:00: root bus resource [bus 00-ff] | ||
| + | [ 0.212492] pci_bus 0000:00: scanning bus | ||
| + | [ 0.216531] pci 0000: | ||
| + | [ 0.222579] pci 0000: | ||
| + | [ 0.229402] pci 0000: | ||
| + | [ 0.235701] pci 0000: | ||
| + | [ 0.242000] pci 0000: | ||
| + | [ 0.248298] pci 0000: | ||
| + | [ 0.255389] pci_bus 0000:00: fixups for bus | ||
| + | [ 0.259596] pci_bus 0000:00: bus scan returning with max=00 | ||
| + | [ 0.265497] clocksource: | ||
| + | [ 0.277095] thermal_sys: | ||
| + | [ 0.277098] thermal_sys: | ||
| + | [ 0.283247] thermal_sys: | ||
| + | [ 0.289285] thermal_sys: | ||
| + | [ 0.295320] thermal_sys: | ||
| + | [ 0.301662] NET: Registered protocol family 2 | ||
| + | [ 0.312683] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) | ||
| + | [ 0.320609] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.329099] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.336909] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) | ||
| + | [ 0.344123] TCP: Hash tables configured (established 4096 bind 4096) | ||
| + | [ 0.350570] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.357141] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.364219] NET: Registered protocol family 1 | ||
| + | [ 0.368619] PCI: CLS 0 bytes, default 64 | ||
| + | [ 0.373436] workingset: timestamp_bits=46 max_order=17 bucket_order=0 | ||
| + | [ 0.383504] squashfs: version 4.0 (2009/ | ||
| + | [ 0.389506] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | ||
| + | [ 0.400856] fuse: init (API version 7.31) | ||
| + | [ 0.417723] phy phy-usb-phy@11e10000.1: | ||
| + | [ 0.434968] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled | ||
| + | [ 0.442443] printk: console [ttyS0] disabled | ||
| + | [ 0.466928] 11002000.serial: | ||
| + | [ 0.476137] printk: console [ttyS0] enabled | ||
| + | [ 0.476137] printk: console [ttyS0] enabled | ||
| + | [ 0.484495] printk: bootconsole [uart8250] disabled | ||
| + | [ 0.484495] printk: bootconsole [uart8250] disabled | ||
| + | [ 0.494919] mtk_rng trng@1020f000: | ||
| + | [ 0.494937] random: fast init done | ||
| + | [ 0.503700] random: crng init done | ||
| + | [ 0.507306] cacheinfo: Unable to detect cache hierarchy for CPU 0 | ||
| + | [ 0.515822] loop: module loaded | ||
| + | [ 0.519116] mediatek, | ||
| + | [ 0.526081] mediatek, | ||
| + | [ 0.534116] mt7981-pinctrl 11d00000.pinctrl: | ||
| + | [ 0.541515] mtk-spi 1100a000.spi: | ||
| + | [ 0.549127] spi-nand spi0.0: Macronix SPI NAND was found. | ||
| + | [ 0.554542] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 | ||
| + | [ 0.564132] libphy: Fixed MDIO Bus: probed | ||
| + | [ 0.580022] libphy: mdio: probed | ||
| + | [ 0.583682] mtk_soc_eth 15100000.ethernet: | ||
| + | [ 0.592146] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011c00000, | ||
| + | [ 0.601216] mtk_soc_eth 15100000.ethernet: | ||
| + | [ 0.609648] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011c00000, | ||
| + | [ 0.618689] (unnamed net_device) (dummy): netif_napi_add() called with weight 256 | ||
| + | [ 0.626323] PPP generic driver version 2.4.2 | ||
| + | [ 0.630709] PPP BSD Compression module registered | ||
| + | [ 0.635414] PPP Deflate Compression module registered | ||
| + | [ 0.640498] PPP MPPE Compression module registered | ||
| + | [ 0.645280] NET: Registered protocol family 24 | ||
| + | [ 0.649728] PPTP driver version 0.8.5 | ||
| + | [ 0.653718] xhci-mtk 11200000.xhci: | ||
| + | [ 0.662351] xhci-mtk 11200000.xhci: | ||
| + | [ 0.671357] xhci-mtk 11200000.xhci: | ||
| + | [ 0.676679] xhci-mtk 11200000.xhci: | ||
| + | [ 0.687212] xhci-mtk 11200000.xhci: | ||
| + | [ 0.696453] xhci-mtk 11200000.xhci: | ||
| + | [ 0.702688] hub 1-0:1.0: USB hub found | ||
| + | [ 0.706472] hub 1-0:1.0: 1 port detected | ||
| + | [ 0.710644] xhci-mtk 11200000.xhci: | ||
| + | [ 0.715961] xhci-mtk 11200000.xhci: | ||
| + | [ 0.723441] xhci-mtk 11200000.xhci: | ||
| + | [ 0.730617] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. | ||
| + | [ 0.739066] hub 2-0:1.0: USB hub found | ||
| + | [ 0.742845] hub 2-0:1.0: 1 port detected | ||
| + | [ 0.747167] i2c /dev entries driver | ||
| + | [ 0.752075] mtk-wdt 1001c000.watchdog: | ||
| + | [ 0.760145] device-mapper: | ||
| + | [ 0.769566] crypto-safexcel 10320000.crypto: | ||
| + | [ 0.782110] usbcore: registered new interface driver usbhid | ||
| + | [ 0.787704] usbhid: USB HID core driver | ||
| + | [ 0.792951] u32 classifier | ||
| + | [ 0.795671] | ||
| + | [ 0.799639] xt_time: kernel timezone is -0000 | ||
| + | [ 0.804088] gre: GRE over IPv4 demultiplexor driver | ||
| + | [ 0.808957] ip_gre: GRE over IPv4 tunneling driver | ||
| + | [ 0.814676] Initializing XFRM netlink socket | ||
| + | [ 0.819279] NET: Registered protocol family 10 | ||
| + | [ 0.824489] Segment Routing with IPv6 | ||
| + | [ 0.828358] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver | ||
| + | [ 0.834999] NET: Registered protocol family 17 | ||
| + | [ 0.839505] Bridge firewalling registered | ||
| + | [ 0.843667] l2tp_core: L2TP core driver, V2.0 | ||
| + | [ 0.848043] l2tp_ppp: PPPoL2TP kernel driver, V2.0 | ||
| + | [ 0.852825] 8021q: 802.1Q VLAN Support v1.8 | ||
| + | [ 0.865985] nmbm nmbm_spim_nand: | ||
| + | [ 0.873592] nmbm nmbm_spim_nand: | ||
| + | [ 0.883452] nmbm nmbm_spim_nand: | ||
| + | [ 0.891452] nmbm nmbm_spim_nand: | ||
| + | [ 0.898027] 10 fixed-partitions partitions found on MTD device nmbm_spim_nand | ||
| + | [ 0.905158] Creating 10 MTD partitions on " | ||
| + | [ 0.910724] 0x000000000000-0x000000100000 : " | ||
| + | [ 0.916019] 0x000000100000-0x000000180000 : " | ||
| + | [ 0.921962] 0x000000180000-0x000000380000 : " | ||
| + | [ 0.927565] 0x000000380000-0x000000580000 : " | ||
| + | [ 0.932818] 0x000000580000-0x000003780000 : " | ||
| + | [ 0.938147] 0x000003780000-0x000006980000 : " | ||
| + | [ 0.943552] 0x000006980000-0x0000069c0000 : " | ||
| + | [ 0.948796] 0x0000069c0000-0x000006a40000 : " | ||
| + | [ 0.954382] 0x000006a40000-0x000006ac0000 : " | ||
| + | [ 0.959972] 0x000006ac0000-0x0000074c0000 : " | ||
| + | [ 1.175505] libphy: dsa slave smi: probed | ||
| + | [ 1.180386] mt7530 mdio-bus:1f lan0 (uninitialized): | ||
| + | [ 1.189913] mt7530 mdio-bus:1f lan1 (uninitialized): | ||
| + | [ 1.199429] mt7530 mdio-bus:1f lan2 (uninitialized): | ||
| + | [ 1.208919] mt7530 mdio-bus:1f lan3 (uninitialized): | ||
| + | [ 1.217793] mt7530 mdio-bus: | ||
| + | [ 1.224947] DSA: tree 0 setup | ||
| + | [ 1.225193] mt7530 mdio-bus: | ||
| + | [ 1.235511] UBI: auto-attach mtd5 | ||
| + | [ 1.238846] ubi0: attaching mtd5 | ||
| + | [ 1.369869] ubi0: scanning is finished | ||
| + | [ 1.377959] ubi0: attached mtd5 (name " | ||
| + | [ 1.383360] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | ||
| + | [ 1.390227] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | ||
| + | [ 1.397004] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 | ||
| + | [ 1.403953] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0 | ||
| + | [ 1.409949] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 | ||
| + | [ 1.417160] ubi0: max/mean erase counter: 102/62, WL threshold: 4096, image sequence number: 1571737675 | ||
| + | [ 1.426538] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 19 | ||
| + | [ 1.435749] ubi0: background thread " | ||
| + | [ 1.442333] block ubiblock0_1: | ||
| + | [ 1.447833] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem | ||
| + | [ 1.455187] input: gpio-keys as / | ||
| + | [ 1.462062] hctosys: unable to open rtc device (rtc0) | ||
| + | [ 1.470365] VFS: Mounted root (squashfs filesystem) readonly on device 253:0. | ||
| + | [ 1.478962] devtmpfs: mounted | ||
| + | [ 1.482126] Freeing unused kernel memory: 448K | ||
| + | [ 1.493528] Run /sbin/init as init process | ||
| + | INIT: version 2.99 booting | ||
| + | create r/w /etc folder | ||
| + | create r/w /var folder | ||
| + | run / | ||
| + | Starting udev | ||
| + | [ 3.294937] udevd[988]: starting version 3.2.10 | ||
| + | [ 3.344518] udevd[989]: starting eudev-3.2.10 | ||
| + | sysctl: cannot stat / | ||
| + | hwclock: can't open '/ | ||
| + | Fri Mar 9 12:34:56 UTC 2018 | ||
| + | hwclock: can't open '/ | ||
| + | chown: /mydlink: Read-only file system | ||
| + | Failed to set owner -root- for -/ | ||
| + | chmod: /mydlink: Read-only file system | ||
| + | Failed to set mode -1400- for -/ | ||
| + | cat: read error: Is a directory | ||
| + | cat: read error: Is a directory | ||
| + | cat: read error: Is a directory | ||
| + | Starting mount / | ||
| + | do_check_ubi_mount: | ||
| + | **(mkdir -p / | ||
| + | do_ubi_mkdir: | ||
| + | r/storage ok | ||
| + | **(ubiattach / | ||
| + | [ 4.791975] ubi2: scanning is finished | ||
| + | [ 4.800695] ubi2: attached mtd10 (name " | ||
| + | [ 4.806544] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | ||
| + | [ 4.813409] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | ||
| + | [ 4.820185] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 | ||
| + | [ 4.827134] ubi2: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 | ||
| + | [ 4.833041] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 | ||
| + | [ 4.840251] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 7827181 | ||
| + | [ 4.849108] ubi2: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 19 | ||
| + | [ 4.858236] ubi2: background thread " | ||
| + | UBI device number 2, total 80 LEBs (10158080 byt[ 4.867564] UBIFS (ubi2:0): Mounting in unauthenticated mode | ||
| + | es, 9.6 MiB), av[ 4.874296] UBIFS (ubi2:0): background thread " | ||
| + | ailable 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) | ||
| + | do_ubi_attach: | ||
| + | **(mount -t ubifs ubi2_0 / | ||
| + | [ 4.902034] UBIFS (ubi2:0): recovery needed | ||
| + | [ 4.948646] UBIFS (ubi2:0): recovery completed | ||
| + | [ 4.953166] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name " | ||
| + | [ 4.960647] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes | ||
| + | [ 4.970558] UBIFS (ubi2:0): FS size: 5967872 bytes (5 MiB, 47 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) | ||
| + | [ 4.980634] UBIFS (ubi2:0): reserved for root: 281876 bytes (275 KiB) | ||
| + | [ 4.987069] UBIFS (ubi2:0): media format: w5/r0 (latest is w5/r0), UUID 7C5C2863-F17C-474B-ADD3-5A0DAD4120F4, | ||
| + | do_ubi_mount: | ||
| + | done | ||
| + | Starting untar webui-dlink: | ||
| + | Starting paccess: read_psec2datfile: | ||
| + | done | ||
| + | Starting csman: [csmsal_open]feed_csiddata (/ | ||
| + | [csmsal_open]feed_csiddata (/ | ||
| + | [csmsal_open]feed_csiddata (/ | ||
| + | hookcs_load[182]: | ||
| + | [hookcs_load] C Area img Icksum() OK!(7CB9)(7CB9)(5802) | ||
| + | hookcs_load[182]: | ||
| + | [hookcs_load] C Area img Icksum() OK!(D342)(D342)(5809) | ||
| + | C section 2 is up to date, load C section 2... | ||
| + | [csmsal_open]feed_csiddata csection | ||
| + | [csm_svr_init]csmsal open("/ | ||
| + | done | ||
| + | Starting syslogd/ | ||
| + | fs.protected_hardlinks = 1 | ||
| + | fs.protected_symlinks = 1 | ||
| + | mount: mounting none on / | ||
| + | Same FW, do nothing | ||
| + | Starting commander: Tue Jul 11 03:26:40 UTC 2023 | ||
| + | Ether WAN NUM = 1 | ||
| + | WAN = XX: | ||
| + | LAN = XX: | ||
| + | WLAN0 = XX: | ||
| + | WLAN1 = XX: | ||
| + | WLAN2 = XX: | ||
| + | WLAN3 = XX: | ||
| + | WLAN4 = XX: | ||
| + | WLAN5 = XX: | ||
| + | WLAN6 = XX: | ||
| + | WLAN7 = XX: | ||
| + | BEID STATUS | ||
| + | [vlan] vlan for M30 - v1.1.9 | ||
| + | [vlan] vlan Start | ||
| + | [vlan] Complete Cmd | ||
| + | WAN = XX: | ||
| + | LAN = XX: | ||
| + | WLAN0 = XX: | ||
| + | WLAN1 = XX: | ||
| + | WLAN2 = XX: | ||
| + | WLAN3 = XX: | ||
| + | WLAN4 = XX: | ||
| + | WLAN5 = XX: | ||
| + | WLAN6 = XX: | ||
| + | WLAN7 = XX: | ||
| + | BEID STATUS | ||
| + | [vlan] Interface br0 Have Down | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | [vlan] Interface brx0 Have Down | ||
| + | [vlan] Brx Interface brx0 Down | ||
| + | bridge brx0 doesn' | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | [vlan] Interface brx1 Have Down | ||
| + | [vlan] Brx Interface brx1 Down | ||
| + | bridge brx1 doesn' | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | [vlan] Interface brx2 Have Down | ||
| + | [vlan] Brx Interface brx2 Down | ||
| + | bridge brx2 doesn' | ||
| + | [vlan] triple play = 0 | ||
| + | [vlan] wanNum = 1, lanNum = 4, virturalwanNum = 0 | ||
| + | [vlan] wanIndex = 0, lanIndex = 1, virtualwanIndex = 5 | ||
| + | [vlan] wan port map: 4 | ||
| + | [[ | ||
| + | vlan] i = 0 posi[ | ||
| + | tion = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 | ||
| + | [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 | ||
| + | [vlan] i = 0 wanMac = xxxxxxxxxxcc | ||
| + | [vlan] i = 0 portMac = 000000000000 | ||
| + | [vlan] i = 0 wanInterface = eth1 | ||
| + | [vlan] i = 0 portInterface = eth1 | ||
| + | [vlan] lan port map: 0 1 2 3 -1 | ||
| + | [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 | ||
| + | [vlan] i = 1 lanIndex = 0 | ||
| + | [vlan] i = 1 lanMac = xxxxxxxxxxcd | ||
| + | [vlan] i = 1 portMac = 000000000000 | ||
| + | [vlan] i = 1 portInterface = eth0 | ||
| + | [vlan] i = 1 lanInterface = | ||
| + | [vlan] i = 2 position = 2 type = 2 [ | ||
| + | portIndex = 1 po[ | ||
| + | rtLogic = 1 port[ | ||
| + | PhyId = 1 | ||
| + | [vlan] i = 2 lanIndex = 1 | ||
| + | [vlan] i = 2 lanMac = ca787deba0cd | ||
| + | [vl[ | ||
| + | an] i = 2 portMa[ | ||
| + | c = 000000000000[ | ||
| + | |||
| + | [vlan] i = 2 portInterface = eth0 | ||
| + | [vlan] i = 2 lanInterface = | ||
| + | [vlan] i =[ | ||
| + | 3 position = 3 [ | ||
| + | type = 2 portInd[ | ||
| + | ex = 2 portLogic = 2 portPhyId = 2 | ||
| + | [vlan] i = 3 lanIndex = 2 | ||
| + | [vlan] i = 3 la[ | ||
| + | nMac = ce787deba[ | ||
| + | 0cd | ||
| + | [vlan] i =[ | ||
| + | 3 portMac = 000000000000 | ||
| + | [vlan] i = 3 portInterface = eth0 | ||
| + | [vlan] i = 3 lanInterface = | ||
| + | [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3 | ||
| + | [vlan] i = 4 lanIndex = 3 | ||
| + | [vlan][ | ||
| + | i = 4 lanMac = [ | ||
| + | c2787deba0cd | ||
| + | [[ | ||
| + | vlan] i = 4 portMac = 000000000000 | ||
| + | [vlan] i = 4 portInterface = eth0 | ||
| + | [vlan] i = 4 lanInterface = | ||
| + | [vlan] i = 1 lanInterface = lan0 | ||
| + | [vlan] i = 2 lanInter[ | ||
| + | face = lan1 | ||
| + | [v[ | ||
| + | lan] i = 3 lanInterface = lan2 | ||
| + | [vlan] i = 4 lanInterface = lan3 | ||
| + | [vlan] Vlan First Run | ||
| + | [vlan] Interface eth0 Have Up | ||
| + | set hello timer failed: Result not r[ | ||
| + | epresentable | ||
| + | [[ | ||
| + | vlan] Br Add Lan Interface: lan0 | ||
| + | [vlan] Br Add Lan Interface: lan1 | ||
| + | [vlan] Br Add Lan Interface: lan2 | ||
| + | [vlan] Br Add Lan Interface: lan3 | ||
| + | [vlan] Interface [ | ||
| + | eth0 Have Up | ||
| + | [[ | ||
| + | vlan] Interface lan0 Have Up | ||
| + | [vlan] Lan Interface lan0 Up | ||
| + | [vlan] Interface lan1 Have Up | ||
| + | [vlan] Lan Interface lan1 Up | ||
| + | [vlan] Interface lan2 Have Up | ||
| + | [vlan] Lan Interface lan2 Up | ||
| + | [vlan] Interface lan3 Have Up | ||
| + | [vlan] Lan Interface lan3 Up | ||
| + | [vlan] Interface br0 Have Up | ||
| + | [vlan] Br Interface br0 Up | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [vlan] Interface eth1 Have Up | ||
| + | [vlan] Wan Interface eth1 Up | ||
| + | [vlan] vlan End | ||
| + | NETWORK Initialization finished. Result: 0 | ||
| + | init watchdog | ||
| + | init vlan | ||
| + | init lan | ||
| + | Init Lan | ||
| + | init stp | ||
| + | init ondemand | ||
| + | init multiwan | ||
| + | Initialize MultiWAN | ||
| + | wantype = 0, wantype index = 99, wan mode = 1, route enable = 1 | ||
| + | fo enable = 0, fo stay enable = 0, fo trigger = 0, fo time = 0, fo sequence = 0 | ||
| + | init multi_ondemand | ||
| + | init spap | ||
| + | init ddns | ||
| + | init snmp | ||
| + | SNMP Enterprise Number = 12823 | ||
| + | SNMP Enterprise Name = | ||
| + | SNMP Enterprise OID = 1.3.6.1.4.1.12823 | ||
| + | SNMP Version: 5.8 | ||
| + | init time | ||
| + | sh: line 1: snmpd-action: | ||
| + | Get time from RTC(ds3232) | ||
| + | sh: line 1: / | ||
| + | init user | ||
| + | hwclock: can't open '/ | ||
| + | init dhcpsrv | ||
| + | device br0 already exists; can't create bridge with the same name | ||
| + | IP = 192.168.200.001 | ||
| + | Mask = 255.255.255.000 (ffffff00) - aka /24 | ||
| + | IP range start = 192.168.200.1 | ||
| + | IP range end = 192.168.200.254 | ||
| + | DHCP Server IP pool start = 192.168.200.100 | ||
| + | DHCP Server IP pool end = 192.168.200.249 | ||
| + | sip : 1, eip : 254 | ||
| + | ptr_ip_start : 100 , ptr_ip_end : 249 | ||
| + | DHCP Server IP pool OKOK!! | ||
| + | BusyBox v1.27.2 () multi-call binary. | ||
| + | |||
| + | Usage: rm [-irf] FILE... | ||
| + | BusyBox v1.27.2 () multi-call binary. | ||
| + | |||
| + | Usage: rm [-irf] FILE... | ||
| + | dnsmasq config start | ||
| + | dnsmasq config end | ||
| + | Start Dnsmasq DHCP at init | ||
| + | init dnsrelay | ||
| + | init routing | ||
| + | init route_protocol | ||
| + | init nat | ||
| + | init keepalive | ||
| + | init syslog_interval_timer | ||
| + | init schedule | ||
| + | init ftp_alg | ||
| + | init rtsp_alg | ||
| + | start the RTSP ALG modules | ||
| + | rmmod: can't unload module ' | ||
| + | rmmod: can't unload module ' | ||
| + | [ | ||
| + | ==NAT Stop wan999 ALL== | ||
| + | NAT nat-draft stop rul[ | ||
| + | e start | ||
| + | Flush ip route cache | ||
| + | handle_rtsp_alg: | ||
| + | init qos | ||
| + | init reboot | ||
| + | init reset_btn | ||
| + | init sshd | ||
| + | Add the DROP rules for outgoing packets | ||
| + | init sip_alg | ||
| + | init https | ||
| + | init wireless_mode | ||
| + | module 1 INIT AP ROUTER MODE | ||
| + | Module One AP ROUTER MODE | ||
| + | module 2 INIT AP ROUTER MODE | ||
| + | Module Two AP ROUTER MODE | ||
| + | spi_exception_deinit start | ||
| + | dnsmasq config start | ||
| + | spi end | ||
| + | clear / | ||
| + | mmi_nat_stop | ||
| + | mmi_nat_start | ||
| + | NAT nat-draft stop rule end | ||
| + | ==NAT Start wan999 ALL== | ||
| + | NAT nat-draft stop rule start | ||
| + | Flush ip route cache | ||
| + | spi_exception_deinit start | ||
| + | dnsmasq config end | ||
| + | init wlanap | ||
| + | can not find cisd(8000F500) on Psetion | ||
| + | can not find cisd(8000F501) on Psetion | ||
| + | spi end | ||
| + | clear / | ||
| + | init wpa | ||
| + | init wlanapcli_profile | ||
| + | mmi_nat_stop | ||
| + | Initial WLANAPCLI_PROFILE | ||
| + | init iom | ||
| + | mmi_nat_start | ||
| + | NAT nat-draft stop rule end | ||
| + | NAT nat-draft start rule start | ||
| + | sh: line 1: event_managed: | ||
| + | init wan_led | ||
| + | init status_led | ||
| + | init igmp | ||
| + | All Log Alert options from Firewall are disable. | ||
| + | init mupnpd | ||
| + | init recent | ||
| + | init bonjour | ||
| + | nat-draft stop_ip_forward start | ||
| + | nat-draft stop_ip_forward end | ||
| + | mwlb start | ||
| + | mwlb end | ||
| + | admin start | ||
| + | admin end | ||
| + | virtual computer start | ||
| + | virtual computer end | ||
| + | wanalias start | ||
| + | wanalias end | ||
| + | portfwd start | ||
| + | portfwd end | ||
| + | Single DMZ start | ||
| + | init dnscrypt_proxy | ||
| + | init aplan | ||
| + | Start init_aplan... | ||
| + | init pptp | ||
| + | init pptpserv | ||
| + | init l2tp | ||
| + | [ | ||
| + | |||
| + | init gre | ||
| + | init ipsec | ||
| + | init x509 | ||
| + | init scep | ||
| + | init vrrp | ||
| + | init ntpsrv | ||
| + | init ipv6 | ||
| + | init v6filter | ||
| + | init ddnsv6 | ||
| + | init grouping | ||
| + | init recieve_alter_mode | ||
| + | init guestzone | ||
| + | init mesh | ||
| + | nat_info.wan_index == 999 | ||
| + | mac-control start | ||
| + | mac-control end | ||
| + | init mydlink | ||
| + | init WPS | ||
| + | init ClientInfo | ||
| + | init dlink_fota | ||
| + | init dlink_speedtest | ||
| + | init_speedtest[42]: | ||
| + | init eventX_monitor | ||
| + | discard_ping start | ||
| + | discard_ping end | ||
| + | read_csid2rawfile: | ||
| + | inblkwpkts start | ||
| + | read_csid2rawfile: | ||
| + | inblkwpkts end | ||
| + | adjust_mss start | ||
| + | | ||
| + | | ||
| + | adjust_mss end | ||
| + | Add temporary fwd_BT rules (check_fwd_recent: | ||
| + | Remove temporary fwd_BT rules | ||
| + | done | ||
| + | fwd-recent start | ||
| + | fwd-recent end | ||
| + | | ||
| + | | ||
| + | | ||
| + | WiFi Module One Operation Mode is changed | ||
| + | WiFi Module Two Operation Mode is changed | ||
| + | WiFi Operation Mode is Changed and Apply Wirelessmode Alter from Commander | ||
| + | Disable WAN bridges to LAN | ||
| + | NAT alg start | ||
| + | NAT alg end | ||
| + | device eth1 is not a port of br0 | ||
| + | Configuring packages on first boot.... | ||
| + | (This may take several minutes. Please do not power off the machine.) | ||
| + | pkt-filter start | ||
| + | pkt-filter end | ||
| + | pkt-filterv6 start | ||
| + | pkt-filterv6 end | ||
| + | Sorry, rule does not exist. | ||
| + | Module One AP ROUTER MODE | ||
| + | Module Two AP ROUTER MODE | ||
| + | [ | ||
| + | l7appblk start | ||
| + | l7appblk end | ||
| + | ## Error: " | ||
| + | url-block start | ||
| + | fwd_block_url_file_extension | ||
| + | url-block end | ||
| + | ## Error: " | ||
| + | url-block start | ||
| + | fwd_block_url | ||
| + | url-block end | ||
| + | nat-draft start_ip_forward start | ||
| + | sh / | ||
| + | dnsmasq config start | ||
| + | [ | ||
| + | ## Error: " | ||
| + | nat-draft start_ip_forward end | ||
| + | stealth-mode start | ||
| + | dnsmasq config end | ||
| + | stealth-mode end | ||
| + | spi_exception_deinit start | ||
| + | spi end | ||
| + | spi_exception_init start | ||
| + | spi end | ||
| + | pre_spi_mode start | ||
| + | spi end | ||
| + | security_v6 start | ||
| + | security_v6 end | ||
| + | Conntrack -F start | ||
| + | Wait 2 seconds | ||
| + | wlan_phase_two_config | ||
| + | killall: rt2860apd: no process killed | ||
| + | Wireless 8021X Stop | ||
| + | killall: mosquitto: no process killed | ||
| + | killall: EasyMeshDaemon: | ||
| + | killall: emhandler: no process killed | ||
| + | killall: emLooping: no process killed | ||
| + | killall: emDiscovery: | ||
| + | killall: mapd: no process killed | ||
| + | killall: p1905_managerd: | ||
| + | killall: wapp: no process killed | ||
| + | update-rc.d: | ||
| + | INIT: Entering runlevel: 5up link | ||
| + | Configuring network interfaces... RTNETLINK answers: File exists | ||
| + | Disable WLAN interface. | ||
| + | WLAN Two interface down! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface rax0 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface rax1 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface rax2 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | WLAN One interface down! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface ra0 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface ra1 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | interface ra2 does not exist! | ||
| + | ifconfig: SIOCGIFFLAGS: | ||
| + | rmmod: can't unload module ' | ||
| + | killall: fwdd: no process killed | ||
| + | rmmod: can't unload module ' | ||
| + | rmmod: can't unload module ' | ||
| + | rmmod: can't unload module ' | ||
| + | killall: ACSDaemon: no process killed | ||
| + | Enable WLAN interface. | ||
| + | assigned dat_path:/ | ||
| + | dat_path:/ | ||
| + | assigned dat_path:/ | ||
| + | assigned csid_index: | ||
| + | dat_path:/ | ||
| + | assigned dat_path:/ | ||
| + | assigned csid_index: | ||
| + | dat_path:/ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | conntrack v1.4.6 (conntrack-tools): | ||
| + | Conntrack -F end | ||
| + | NAT nat-draft start rule end | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | WLAN One interface up! | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [wlanap] is2G_enable= 1, is5G_enable= 1 | ||
| + | [wlanap] if_wlan_2G= ra0, if_wlan_5G= rax0 | ||
| + | Set multicast_to_unicast kernel option to 1 on interface ra0 | ||
| + | / | ||
| + | ra0 Channel Value: 4 | ||
| + | WLAN Two interface up! | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | Set multicast_to_unicast kernel option to 1 on interface ra0 | ||
| + | / | ||
| + | Set multicast_to_unicast kernel option to 1 on interface rax0 | ||
| + | / | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [wlanap] is2G_enable= 1, is5G_enable= 1 | ||
| + | [wlanap] if_wlan_2G= ra0, if_wlan_5G= rax0 | ||
| + | Set multicast_to_unicast kernel option to 1 on interface ra0 | ||
| + | / | ||
| + | Set multicast_to_unicast kernel option to 1 on interface rax0 | ||
| + | / | ||
| + | Set multicast_to_unicast kernel option to 1 on interface rax1 | ||
| + | / | ||
| + | rax0 Channel Value: 48 | ||
| + | nf_handle_macctl_wlanap 2776 iwpriv ra0 set AccessPolicy=0 | ||
| + | nf_handle_macctl_wlanap 2793 iwpriv rax0 set AccessPolicy=0 | ||
| + | nf_handle_macctl_wlanap 2793 iwpriv rax1 set AccessPolicy=0 | ||
| + | Run smp.sh & | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [fwdd][send_ctrl_msg]net link socket didn't created. | ||
| + | [fwdd][send_ctrl_msg]net link socket didn't created. | ||
| + | cat: can't open '/ | ||
| + | [get_mesh_conf] mesh_dlink_get_mesh_role(), | ||
| + | [vlan] vlan for M30 - v1.1.9 | ||
| + | [vlan] vlan Start | ||
| + | [vlan] triple play = 0 | ||
| + | [vlan] wanNum = 1, lanNum = 4, virturalwanNum = 0 | ||
| + | [vlan] wanIndex = 0, lanIndex = 1, virtualwanIndex = 5 | ||
| + | [vlan] wan port map: 4 | ||
| + | [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 | ||
| + | [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 | ||
| + | [vlan] i = 0 wanMac = xxxxxxxxxxcc | ||
| + | [vlan] i = 0 portMac = 000000000000 | ||
| + | [vlan] i = 0 wanInterface = eth1 | ||
| + | [vlan] i = 0 portInterface = eth1 | ||
| + | [vlan] lan port map: 0 1 2 3 -1 | ||
| + | [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 | ||
| + | [vlan] i = 1 lanIndex = 0 | ||
| + | [vlan] i = 1 lanMac = xxxxxxxxxxcd | ||
| + | [vlan] i = 1 portMac = 000000000000 | ||
| + | [vlan] i = 1 portInterface = eth0 | ||
| + | [vlan] i = 1 lanInterface = | ||
| + | [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1 | ||
| + | [vlan] i = 2 lanIndex = 1 | ||
| + | [vlan] i = 2 lanMac = ca787deba0cd | ||
| + | [vlan] i = 2 portMac = 000000000000 | ||
| + | [vlan] i = 2 portInterface = eth0 | ||
| + | [vlan] i = 2 lanInterface = | ||
| + | [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 | ||
| + | [vlan] i = 3 lanIndex = 2 | ||
| + | [vlan] i = 3 lanMac = ce787deba0cd | ||
| + | [vlan] i = 3 portMac = 000000000000 | ||
| + | [vlan] i = 3 portInterface = eth0 | ||
| + | [vlan] i = 3 lanInterface = | ||
| + | [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3 | ||
| + | [vlan] i = 4 lanIndex = 3 | ||
| + | [vlan] i = 4 lanMac = c2787deba0cd | ||
| + | [vlan] i = 4 portMac = 000000000000 | ||
| + | [vlan] i = 4 portInterface = eth0 | ||
| + | [vlan] i = 4 lanInterface = | ||
| + | [vlan] i = 1 lanInterface = lan0 | ||
| + | [vlan] i = 2 lanInterface = lan1 | ||
| + | [vlan] i = 3 lanInterface = lan2 | ||
| + | [vlan] i = 4 lanInterface = lan3 | ||
| + | [vlan] Port Map 11110000 | ||
| + | [vlan] Complete Cmd | ||
| + | [vlan] Vlan Cmd Exit | ||
| + | [vlan] vlan End | ||
| + | [vlan] vlan for M30 - v1.1.9 | ||
| + | [vlan] vlan Start | ||
| + | [vlan] triple play = 0 | ||
| + | [vlan] wanNum = 1, lanNum = 4, virturalwanNum = 0 | ||
| + | [vlan] wanIndex = 0, lanIndex = 1, virtualwanIndex = 5 | ||
| + | [vlan] wan port map: 4 | ||
| + | [vlan] i = 0 position = 0 type = 1 portIndex = 4 portLogic = 4 portPhyId = 99 | ||
| + | [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 | ||
| + | [vlan] i = 0 wanMac = xxxxxxxxxxcc | ||
| + | [vlan] i = 0 portMac = 000000000000 | ||
| + | [vlan] i = 0 wanInterface = eth1 | ||
| + | [vlan] i = 0 portInterface = eth1 | ||
| + | [vlan] lan port map: 0 1 2 3 -1 | ||
| + | [vlan] i = 1 position = 1 type = 2 portIndex = 0 portLogic = 0 portPhyId = 0 | ||
| + | [vlan] i = 1 lanIndex = 0 | ||
| + | [vlan] i = 1 lanMac = xxxxxxxxxxcd | ||
| + | [vlan] i = 1 portMac = 000000000000 | ||
| + | [vlan] i = 1 portInterface = eth0 | ||
| + | [vlan] i = 1 lanInterface = | ||
| + | [vlan] i = 2 position = 2 type = 2 portIndex = 1 portLogic = 1 portPhyId = 1 | ||
| + | [vlan] i = 2 lanIndex = 1 | ||
| + | [vlan] i = 2 lanMac = ca787deba0cd | ||
| + | [vlan] i = 2 portMac = 000000000000 | ||
| + | [vlan] i = 2 portInterface = eth0 | ||
| + | [vlan] i = 2 lanInterface = | ||
| + | [vlan] i = 3 position = 3 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 | ||
| + | [vlan] i = 3 lanIndex = 2 | ||
| + | [vlan] i = 3 lanMac = ce787deba0cd | ||
| + | [vlan] i = 3 portMac = 000000000000 | ||
| + | [vlan] i = 3 portInterface = eth0 | ||
| + | [vlan] i = 3 lanInterface = | ||
| + | [vlan] i = 4 position = 4 type = 2 portIndex = 3 portLogic = 3 portPhyId = 3 | ||
| + | [vlan] i = 4 lanIndex = 3 | ||
| + | [vlan] i = 4 lanMac = c2787deba0cd | ||
| + | [vlan] i = 4 portMac = 000000000000 | ||
| + | [vlan] i = 4 portInterface = eth0 | ||
| + | [vlan] i = 4 lanInterface = | ||
| + | [vlan] i = 1 lanInterface = lan0 | ||
| + | [vlan] i = 2 lanInterface = lan1 | ||
| + | [vlan] i = 3 lanInterface = lan2 | ||
| + | [vlan] i = 4 lanInterface = lan3 | ||
| + | [vlan] Port Map 11110000 | ||
| + | [vlan] Complete Cmd | ||
| + | [vlan] Vlan Cmd Exit | ||
| + | [vlan] vlan End | ||
| + | Start Spanning Tree Protocol | ||
| + | |||
| + | v1.25 | ||
| + | Created SM Eventloop successfully | ||
| + | M30-A0CD | ||
| + | [MEMBER_SM] Loading Configuration : | ||
| + | Filepath is: / | ||
| + | Filename with path is / | ||
| + | handle_nat: nat stop | ||
| + | ==NAT Stop wan999 ALL== | ||
| + | NAT nat-draft stop rule start | ||
| + | Flush ip route cache | ||
| + | Add the DROP rules for outgoing packets | ||
| + | spi_exception_deinit start | ||
| + | spi end | ||
| + | clear / | ||
| + | clear / | ||
| + | clear / | ||
| + | clear / | ||
| + | mmi_nat_stop | ||
| + | mmi_nat_start | ||
| + | NAT nat-draft stop rule end | ||
| + | Force to start schedule without consider the Time Sync status! | ||
| + | Start Mini-UPNP !! | ||
| + | [V] [start][1530]WirelessRouter Mode | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | Start Mini-UPNP !! | ||
| + | ==NAT Stop wan999 mupnpd== | ||
| + | NAT nat-draft stop rule start | ||
| + | NAT nat-draft stop rule end | ||
| + | ==NAT Start wan999 mupnpd== | ||
| + | NAT nat-draft stop rule start | ||
| + | NAT nat-draft stop rule end | ||
| + | NAT nat-draft start rule start | ||
| + | nat-draft stop_ip_forward start | ||
| + | func not ' | ||
| + | discard_ping start | ||
| + | discard_ping end | ||
| + | inblkwpkts start | ||
| + | inblkwpkts end | ||
| + | adjust_mss start | ||
| + | adjust_mss end | ||
| + | Add temporary fwd_BT rules (check_fwd_recent: | ||
| + | Remove temporary fwd_BT rules | ||
| + | NAT alg start | ||
| + | NAT alg end | ||
| + | nat-draft start_ip_forward start | ||
| + | func not ' | ||
| + | stealth-mode start | ||
| + | stealth-mode end | ||
| + | security_v6 start | ||
| + | security_v6 end | ||
| + | NAT nat-draft start rule end | ||
| + | Error: Cannot delete qdisc with handle of zero. | ||
| + | Error: Cannot delete qdisc with handle of zero. | ||
| + | switch port=0 egress rate limit off | ||
| + | switch port=1 egress rate limit off | ||
| + | switch port=2 egress rate limit off | ||
| + | switch port=3 egress rate limit off | ||
| + | [ | ||
| + | create dhcpd6.leases xxxxxxxxxxxxxxxx | ||
| + | Error: Cannot delete qdisc with handle of zero. | ||
| + | Error: Cannot delete qdisc with handle of zero. | ||
| + | switch port=0 egress rate limit off | ||
| + | switch port=1 egress rate limit off | ||
| + | switch port=2 egress rate limit off | ||
| + | switch port=3 egress rate limit off | ||
| + | restart the SIP ALG modules | ||
| + | RTNETLINK answers: Address not available | ||
| + | RTNETLINK answers: Address not available | ||
| + | ## Lunching system normally completed! ## | ||
| + | </ | ||
| </ | </ | ||
| ==== OpenWrt bootlog ==== | ==== OpenWrt bootlog ==== | ||
| <WRAP bootlog> | <WRAP bootlog> | ||
| - | < | + | < |
| + | [ 0.000000] Linux version 6.6.41 (roland@Linux) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26971-66177c081f) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Fri Jul 26 11:41:25 2024 | ||
| + | [ 0.000000] Machine model: D-Link AQUILA PRO AI M30 A1 | ||
| + | [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '' | ||
| + | [ 0.000000] printk: bootconsole [uart8250] enabled | ||
| + | [ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000 | ||
| + | [ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000 | ||
| + | [ 0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000 | ||
| + | [ 0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000 | ||
| + | [ 0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000 | ||
| + | [ 0.000000] Zone ranges: | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Movable zone start for each node | ||
| + | [ 0.000000] Early memory node ranges | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] | ||
| + | [ 0.000000] psci: probing for conduit method from DT. | ||
| + | [ 0.000000] psci: PSCIv1.1 detected in firmware. | ||
| + | [ 0.000000] psci: Using standard PSCI v0.2 function IDs | ||
| + | [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. | ||
| + | [ 0.000000] psci: SMC Calling Convention v1.2 | ||
| + | [ 0.000000] percpu: Embedded 18 pages/cpu s34600 r8192 d30936 u73728 | ||
| + | [ 0.000000] pcpu-alloc: s34600 r8192 d30936 u73728 alloc=18*4096 | ||
| + | [ 0.000000] pcpu-alloc: [0] 0 [0] 1 | ||
| + | [ 0.000000] Detected VIPT I-cache on CPU0 | ||
| + | [ 0.000000] CPU features: detected: GIC system register CPU interface | ||
| + | [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration | ||
| + | [ 0.000000] alternatives: | ||
| + | [ 0.000000] Kernel command line: console=ttyS0, | ||
| + | [ 0.000000] Unknown kernel command line parameters " | ||
| + | [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) | ||
| + | [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) | ||
| + | [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 | ||
| + | [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | ||
| + | [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB | ||
| + | [ 0.000000] software IO TLB: area num 2. | ||
| + | [ 0.000000] software IO TLB: mapped [mem 0x000000005f540000-0x000000005f5c0000] (0MB) | ||
| + | [ 0.000000] Memory: 496904K/ | ||
| + | [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, | ||
| + | [ 0.000000] rcu: Hierarchical RCU implementation. | ||
| + | [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. | ||
| + | [ 0.000000] Tracing variant of Tasks RCU enabled. | ||
| + | [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. | ||
| + | [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, | ||
| + | [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 | ||
| + | [ 0.000000] GICv3: GIC: Using split EOI/ | ||
| + | [ 0.000000] GICv3: 640 SPIs implemented | ||
| + | [ 0.000000] GICv3: 0 Extended SPIs implemented | ||
| + | [ 0.000000] Root IRQ handler: gic_handle_irq | ||
| + | [ 0.000000] GICv3: GICv3 features: 16 PPIs | ||
| + | [ 0.000000] GICv3: CPU0: found redistributor 0 region 0: | ||
| + | [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. | ||
| + | [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). | ||
| + | [ 0.000000] clocksource: | ||
| + | [ 0.000000] sched_clock: | ||
| + | [ 0.008123] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) | ||
| + | [ 0.018533] pid_max: default: 32768 minimum: 301 | ||
| + | [ 0.026077] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.033431] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.043276] cacheinfo: Unable to detect cache hierarchy for CPU 0 | ||
| + | [ 0.049933] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1. | ||
| + | [ 0.057689] rcu: Hierarchical SRCU implementation. | ||
| + | [ 0.062516] rcu: Max phase no-delay instances is 1000. | ||
| + | [ 0.068154] smp: Bringing up secondary CPUs ... | ||
| + | [ 0.073083] Detected VIPT I-cache on CPU1 | ||
| + | [ 0.073127] GICv3: CPU1: found redistributor 1 region 0: | ||
| + | [ 0.073154] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | ||
| + | [ 0.073218] smp: Brought up 1 node, 2 CPUs | ||
| + | [ 0.094829] SMP: Total of 2 processors activated. | ||
| + | [ 0.099551] CPU features: detected: 32-bit EL0 Support | ||
| + | [ 0.104709] CPU features: detected: CRC32 instructions | ||
| + | [ 0.109898] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching | ||
| + | [ 0.118288] CPU: All CPU(s) started at EL2 | ||
| + | [ 0.122401] alternatives: | ||
| + | [ 0.131412] clocksource: | ||
| + | [ 0.141318] futex hash table entries: 512 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.149385] pinctrl core: initialized pinctrl subsystem | ||
| + | [ 0.155479] NET: Registered PF_NETLINK/ | ||
| + | [ 0.162011] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations | ||
| + | [ 0.169146] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations | ||
| + | [ 0.176944] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations | ||
| + | [ 0.185261] thermal_sys: | ||
| + | [ 0.185266] thermal_sys: | ||
| + | [ 0.191386] thermal_sys: | ||
| + | [ 0.197429] thermal_sys: | ||
| + | [ 0.203546] ASID allocator initialised with 65536 entries | ||
| + | [ 0.216098] pstore: Using crash dump compression: | ||
| + | [ 0.221534] pstore: Registered ramoops as persistent store backend | ||
| + | [ 0.227740] ramoops: using 0x10000@0x42ff0000, | ||
| + | [ 0.239638] Modules: 29584 pages in range for non-PLT usage | ||
| + | [ 0.239648] Modules: 521104 pages in range for PLT usage | ||
| + | [ 0.246369] cryptd: max_cpu_qlen set to 1000 | ||
| + | [ 0.258135] SCSI subsystem initialized | ||
| + | [ 0.262056] libata version 3.00 loaded. | ||
| + | [ 0.267415] clocksource: | ||
| + | [ 0.275854] NET: Registered PF_INET protocol family | ||
| + | [ 0.280918] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) | ||
| + | [ 0.289386] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.297797] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) | ||
| + | [ 0.305582] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.313393] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) | ||
| + | [ 0.320744] TCP: Hash tables configured (established 4096 bind 4096) | ||
| + | [ 0.327206] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.333796] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.341020] NET: Registered PF_UNIX/ | ||
| + | [ 0.346727] PCI: CLS 0 bytes, default 64 | ||
| + | [ 0.351972] workingset: timestamp_bits=46 max_order=17 bucket_order=0 | ||
| + | [ 0.363213] squashfs: version 4.0 (2009/ | ||
| + | [ 0.369091] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | ||
| + | [ 0.422037] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled | ||
| + | [ 0.429687] printk: console [ttyS0] disabled | ||
| + | [ 0.454350] 11002000.serial: | ||
| + | [ 0.463577] printk: console [ttyS0] enabled | ||
| + | [ 0.471953] printk: bootconsole [uart8250] disabled | ||
| + | [ 0.486315] loop: module loaded | ||
| + | [ 0.491384] spi-nand spi0.0: Macronix SPI NAND was found. | ||
| + | [ 0.496783] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 | ||
| + | [ 0.505444] Signature found at block 1023 [0x07fe0000] | ||
| + | [ 0.510600] NMBM management region starts at block 960 [0x07800000] | ||
| + | [ 0.517853] First info table with writecount 0 found in block 960 | ||
| + | [ 0.526151] Second info table with writecount 0 found in block 963 | ||
| + | [ 0.532341] NMBM has been successfully attached | ||
| + | [ 0.537170] 10 fixed-partitions partitions found on MTD device spi0.0 | ||
| + | [ 0.543635] Creating 10 MTD partitions on " | ||
| + | [ 0.548512] 0x000000000000-0x000000100000 : " | ||
| + | [ 0.554158] 0x000000100000-0x000000180000 : " | ||
| + | [ 0.560159] 0x000000180000-0x000000380000 : " | ||
| + | [ 0.566860] 0x000000380000-0x000000580000 : " | ||
| + | [ 0.572950] 0x000000580000-0x000003780000 : " | ||
| + | [ 0.601201] 0x000003780000-0x000006980000 : " | ||
| + | [ 0.629855] 0x000006980000-0x0000069c0000 : " | ||
| + | [ 0.635356] 0x0000069c0000-0x000006a40000 : " | ||
| + | [ 0.641145] 0x000006a40000-0x000006ac0000 : " | ||
| + | [ 0.646907] 0x000006ac0000-0x0000074c0000 : " | ||
| + | [ 0.804462] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081480000, | ||
| + | [ 0.814343] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081480000, | ||
| + | [ 0.824052] i2c_dev: i2c /dev entries driver | ||
| + | [ 0.830799] mtk-wdt 1001c000.watchdog: | ||
| + | [ 0.839801] NET: Registered PF_INET6 protocol family | ||
| + | [ 0.845738] Segment Routing with IPv6 | ||
| + | [ 0.849449] In-situ OAM (IOAM) with IPv6 | ||
| + | [ 0.853406] NET: Registered PF_PACKET protocol family | ||
| + | [ 0.858647] 8021q: 802.1Q VLAN Support v1.8 | ||
| + | [ 0.927279] mt7530-mdio mdio-bus: | ||
| + | [ 0.948363] mt7530-mdio mdio-bus: | ||
| + | [ 0.957341] mt7530-mdio mdio-bus: | ||
| + | [ 0.966294] mt7530-mdio mdio-bus:1f lan1 (uninitialized): | ||
| + | [ 0.986810] mt7530-mdio mdio-bus:1f lan2 (uninitialized): | ||
| + | [ 1.007088] mt7530-mdio mdio-bus:1f lan3 (uninitialized): | ||
| + | [ 1.027373] mt7530-mdio mdio-bus:1f lan4 (uninitialized): | ||
| + | [ 1.038967] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode | ||
| + | [ 1.045705] DSA: tree 0 setup | ||
| + | [ 1.049078] UBI: auto-attach mtd4 | ||
| + | [ 1.052399] ubi0: default fastmap pool size: 20 | ||
| + | [ 1.056918] ubi0: default fastmap WL pool size: 10 | ||
| + | [ 1.061716] ubi0: attaching mtd4 | ||
| + | [ 1.203297] ubi0: scanning is finished | ||
| + | [ 1.211301] ubi0 warning: ubi_eba_init: | ||
| + | [ 1.221797] ubi0: attached mtd4 (name " | ||
| + | [ 1.227200] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes | ||
| + | [ 1.234077] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 | ||
| + | [ 1.240858] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 | ||
| + | [ 1.247811] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0 | ||
| + | [ 1.253804] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 | ||
| + | [ 1.261021] ubi0: max/mean erase counter: 104/71, WL threshold: 4096, image sequence number: 1841881750 | ||
| + | [ 1.270403] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 17 | ||
| + | [ 1.279621] ubi0: background thread " | ||
| + | [ 1.280973] block ubiblock0_1: | ||
| + | [ 1.291109] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem | ||
| + | [ 1.298161] clk: Disabling unused clocks | ||
| + | [ 1.306832] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. | ||
| + | [ 1.314135] Freeing unused kernel memory: 384K | ||
| + | [ 1.318655] Run /sbin/init as init process | ||
| + | [ 1.322741] | ||
| + | [ 1.325694] | ||
| + | [ 1.328399] | ||
| + | [ 1.331526] | ||
| + | [ 1.333873] | ||
| + | [ 1.336567] | ||
| + | [ 1.519806] init: Console is alive | ||
| + | [ 1.523349] init: - watchdog - | ||
| + | [ 1.850358] kmodloader: loading kernel modules from / | ||
| + | [ 1.876160] gpio_button_hotplug: | ||
| + | [ 1.885989] Enter gca230718_probe for device address 64 | ||
| + | [ 1.891272] Creating LED for node led: reg=0 | ||
| + | [ 1.895611] Creating LED for node led: reg=1 | ||
| + | [ 1.899961] Creating LED for node led: reg=2 | ||
| + | [ 1.904288] Creating LED for node led: reg=3 | ||
| + | [ 1.914541] kmodloader: done loading kernel modules from / | ||
| + | [ 1.931753] init: - preinit - | ||
| + | [ 2.256994] mtk_soc_eth 15100000.ethernet internet: renamed from eth1 | ||
| + | [ 2.291008] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/ | ||
| + | [ 2.300804] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/ | ||
| + | [ 2.320345] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode | ||
| + | [ 4.443726] UBIFS (ubi0:2): default file-system created | ||
| + | [ 4.450681] UBIFS (ubi0:2): Mounting in unauthenticated mode | ||
| + | [ 4.456435] UBIFS (ubi0:2): background thread " | ||
| + | [ 4.497169] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name " | ||
| + | [ 4.505028] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes | ||
| + | [ 4.514932] UBIFS (ubi0:2): FS size: 37711872 bytes (35 MiB, 297 LEBs), max 307 LEBs, journal size 1904640 bytes (1 MiB, 15 LEBs) | ||
| + | [ 4.526574] UBIFS (ubi0:2): reserved for root: 1781224 bytes (1739 KiB) | ||
| + | [ 4.533179] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 4F25D334-58BF-46CB-A02D-D1CA05EF3B5D, | ||
| + | [ 4.545768] mount_root: overlay filesystem has not been fully initialized yet | ||
| + | [ 4.553198] mount_root: switching to ubifs overlay | ||
| + | [ 4.560239] overlayfs: null uuid detected in lower fs '/', | ||
| + | [ 4.571945] urandom-seed: | ||
| + | [ 4.620187] random: procd: uninitialized urandom read (4 bytes read) | ||
| + | [ 4.624006] procd: - early - | ||
| + | [ 4.629657] procd: - watchdog - | ||
| + | [ 5.187847] procd: - watchdog - | ||
| + | [ 5.191409] procd: - ubus - | ||
| + | [ 5.887424] random: crng init done | ||
| + | [ 5.894200] procd: - init - | ||
| + | [ 6.218523] kmodloader: loading kernel modules from / | ||
| + | [ 6.240741] crypto-safexcel 10320000.crypto: | ||
| + | [ 6.258398] Loading modules backported from Linux version v6.9.9-0-g28fdf4518483 | ||
| + | [ 6.265790] Backport generated by backports.git v6.1.97-1-29-gf1d24a3683b2 | ||
| + | [ 6.416501] urngd: v1.0.2 started. | ||
| + | [ 6.607806] mt798x-wmac 18000000.wifi: | ||
| + | [ 6.607806] | ||
| + | [ 6.774206] mt798x-wmac 18000000.wifi: | ||
| + | [ 6.867772] mt798x-wmac 18000000.wifi: | ||
| + | [ 6.959198] mt798x-wmac 18000000.wifi: | ||
| + | [ 6.967641] mt798x-wmac 18000000.wifi: | ||
| + | [ 7.050563] mtdblock: MTD device ' | ||
| + | [ 7.112881] mtdblock: MTD device ' | ||
| + | [ 9.199535] PPP generic driver version 2.4.2 | ||
| + | [ 9.204532] NET: Registered PF_PPPOX protocol family | ||
| + | [ 9.212296] kmodloader: done loading kernel modules from / | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| </ | </ | ||