Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:cudy:m1800 [2024/05/16 05:51] – update install maurerletoh:cudy:m1800 [2024/05/16 06:02] – [Tags] maurerle
Line 102: Line 102:
  
 ==== Flash Layout ==== ==== Flash Layout ====
-<WRAP BOX> 
-FIXME //[[:docs:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[docs:techref:flash.layout#partitioning_of_the_flash|example]]).// 
  
-Please check out the article [[docs:techref:flash.layout|Flash layout]]It contains examples and explanations that describe how to document the flash layout. +The following is taken from the M1800V2_GPIO.xlsx in M1800+V2.zip from http://www.cudytech.com/openwrt_software_download
-</WRAP>+
  
 +^ LED                |              | GPIO                      |             
 +^ SYS_BLED_LED  | F16  | JTCLK        | 16                        | Active Low  
 +^ SYS_RED_LED   | G18  | JTMS         | 15                        | Active Low  
 +^ LAN1_LED      | AA17 | ESW_P0_LED_0 | Port#0 PHY LED indicators | Active Low  
 +^ LAN2_LED      | Y16  | ESW_P1_LED_0 | Port#1 PHY LED indicators | Active Low  
 +^ LAN3_LED      | W15  | ESW_P2_LED_0 | Port#2 PHY LED indicators | Active Low  
 +^ LAN4_LED      | AA15 | ESW_P3_LED_0 | Port#3 PHY LED indicators | Active High 
 +^ WAN_LED       | Y15  | ESW_P4_LED_0 | Port#4 PHY LED indicators | Active Low  
 +^                    |              |                                       
 +^ Button        |      |              |                                       
 +^ WPS           | H1   | TXD3         | 7                         | Active Low  
 +^ RESET         | H3   | RXD3         | 8                         | Active Low  
 ==== OEM easy installation ==== ==== OEM easy installation ====
  
Line 135: Line 144:
 === Specific values needed for tftp === === Specific values needed for tftp ===
  
-<WRAP BOX> 
  
-FIXME Enter values for "FILL-IN" below +^ Bootloader tftp server IPv4 address 192.168.1.88   | 
- +^ Firmware tftp image                  | Cudy OpenWRT image |
-^ Bootloader tftp server IPv4 address FILL-IN   | +
-^ Bootloader MAC address (special)     | FILL-IN   | +
-^ Firmware tftp image                  | [[:downloads|Latest OpenWrt release]] (**''NOTE:''** Name must contain //"tftp"//) | +
-^ TFTP transfer window                 | FILL-IN seconds                                | +
-^ TFTP window start                    | approximately FILL-IN seconds after power on   | +
-^ TFTP client required IP address      | FILL-IN                                        | +
- +
-</WRAP>+
  
 ===== Upgrading OpenWrt ===== ===== Upgrading OpenWrt =====
Line 266: Line 266:
 filter  : Brand=Cudy filter  : Brand=Cudy
 filter  : Model=M1800 filter  : Model=M1800
-filter  : Versions= 
 ---- ----
  
Line 344: Line 343:
  
 [[meta:tags|How to add tags]] [[meta:tags|How to add tags]]
-{{tag>EXAMPLETAG}}+{{tag>mt7621 mt7915 2port 32nand 256ram 2port gigabitethernet gigabitethernet 802.11bgn 802.11ax 2core mips 2nic internalantenna}}
  • Last modified: 2024/12/18 14:51
  • by frollic