Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:cudy:m1800 [2024/05/16 05:44] – update install maurerletoh:cudy:m1800 [2024/05/16 06:02] – [Tags] maurerle
Line 79: Line 79:
  
 There are two known options: There are two known options:
 +
 1) The Luci-based UI. 1) The Luci-based UI.
 +
 2) Press and hold the reset button during power up. 2) Press and hold the reset button during power up.
-   The router will request 'recovery.bin' from a TFTP server at +The router will request 'recovery.bin' from a TFTP server at 
-   192.168.1.88.+192.168.1.88.
  
 Both options require a signed firmware binary. Both options require a signed firmware binary.
Line 100: Line 102:
  
 ==== Flash Layout ==== ==== Flash Layout ====
-<WRAP BOX> 
-FIXME //[[:docs:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[docs:techref:flash.layout#partitioning_of_the_flash|example]]).// 
  
-Please check out the article [[docs:techref:flash.layout|Flash layout]]It contains examples and explanations that describe how to document the flash layout. +The following is taken from the M1800V2_GPIO.xlsx in M1800+V2.zip from http://www.cudytech.com/openwrt_software_download
-</WRAP>+
  
 +^ LED                |              | GPIO                      |             
 +^ SYS_BLED_LED  | F16  | JTCLK        | 16                        | Active Low  
 +^ SYS_RED_LED   | G18  | JTMS         | 15                        | Active Low  
 +^ LAN1_LED      | AA17 | ESW_P0_LED_0 | Port#0 PHY LED indicators | Active Low  
 +^ LAN2_LED      | Y16  | ESW_P1_LED_0 | Port#1 PHY LED indicators | Active Low  
 +^ LAN3_LED      | W15  | ESW_P2_LED_0 | Port#2 PHY LED indicators | Active Low  
 +^ LAN4_LED      | AA15 | ESW_P3_LED_0 | Port#3 PHY LED indicators | Active High 
 +^ WAN_LED       | Y15  | ESW_P4_LED_0 | Port#4 PHY LED indicators | Active Low  
 +^                    |              |                                       
 +^ Button        |      |              |                                       
 +^ WPS           | H1   | TXD3         | 7                         | Active Low  
 +^ RESET         | H3   | RXD3         | 8                         | Active Low  
 ==== OEM easy installation ==== ==== OEM easy installation ====
  
-<WRAP BOX> +First you need to download the signed Cudy OpenWRT firmware from here: http://www.cudytech.com/openwrt_software_download
-FIXME //The instructions below are for Broadcom devices and only serve as an example.//\\ +
-**//Remove / modify them if they do not apply to this particular device!//** +
- +
-This section deals with +
-  * How you install OpenWrt from a device freshly opened +
-  * The steps required such as reset to factory defaults if the device has already been configured+
  
-**Note:** Reset router to factory defaults if it has been previously configured. +  * Browse to ''<nowiki>http://192.168.10.1/cgi-bin/luci/admin/panel</nowiki>'' 
-  * Browse to ''<nowiki>http://192.168.1.1/Upgrade.asp</nowiki>'' +  * Click on Firmware 
-  * Upload .bin file to router+  * Upload cudy openwrt bin file to router
   * Wait for it to reboot   * Wait for it to reboot
-  * Telnet to 192.168.1.1 and set a root password, or browse to ''<nowiki>http://192.168.1.1</nowiki>'' if LuCI is installed. +  * SSH to 192.168.1.1 and set a root password, or browse to ''<nowiki>http://192.168.1.1</nowiki>'' if LuCI is installed.
-</WRAP>+
  
 ==== OEM installation using the TFTP method ==== ==== OEM installation using the TFTP method ====
  
-->  [[docs:guide-user:installation:generic.flashing.tftp]]+Download the recovery.bin for your device from this page: 
 +http://www.cudytech.com/openwrt_software_download 
 + 
 +  * Place the recovery.bin in the serving directory of your TFTP server 
 +  * set your IP to 192.168.1.88 
 +  * Press the "Reset" button of Cudy router and hold it. Before the Cudy 
 +router is powered on and before TFTP start to download the firmware, 
 +don't release the "Reset" button 
 +  * Power on the Cudy router. 
 +  * You can release the reset button only when the status LED flashes 
 +red and blue quickly, or when TFTP starts downloading firmware. 
 +  * When the status LED turns solid red, the upgrade is complete.
  
 === Specific values needed for tftp === === Specific values needed for tftp ===
  
-<WRAP BOX> 
  
-FIXME Enter values for "FILL-IN" below +^ Bootloader tftp server IPv4 address 192.168.1.88   | 
- +^ Firmware tftp image                  | Cudy OpenWRT image |
-^ Bootloader tftp server IPv4 address FILL-IN   | +
-^ Bootloader MAC address (special)     | FILL-IN   | +
-^ Firmware tftp image                  | [[:downloads|Latest OpenWrt release]] (**''NOTE:''** Name must contain //"tftp"//) | +
-^ TFTP transfer window                 | FILL-IN seconds                                | +
-^ TFTP window start                    | approximately FILL-IN seconds after power on   | +
-^ TFTP client required IP address      | FILL-IN                                        | +
- +
-</WRAP>+
  
 ===== Upgrading OpenWrt ===== ===== Upgrading OpenWrt =====
Line 260: Line 266:
 filter  : Brand=Cudy filter  : Brand=Cudy
 filter  : Model=M1800 filter  : Model=M1800
-filter  : Versions= 
 ---- ----
  
Line 338: Line 343:
  
 [[meta:tags|How to add tags]] [[meta:tags|How to add tags]]
-{{tag>EXAMPLETAG}}+{{tag>mt7621 mt7915 2port 32nand 256ram 2port gigabitethernet gigabitethernet 802.11bgn 802.11ax 2core mips 2nic internalantenna}}
  • Last modified: 2024/12/18 14:51
  • by frollic