Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:cudy:cudy_wr2100_v1 [2021/11/08 20:45] – [Photos] elcovvtoh:cudy:cudy_wr2100_v1 [2021/11/13 19:24] – [Serial] elcovv
Line 1: Line 1:
-====== Cudy WR2100 v1 ====== +====== Cudy WR2100 ====== 
-The EAP235-Wall is an 802.11ac 4×4:4 Gigabit MediaTek-based access point. It has five 1 Gbps Ethernet ports. It uses 4 external antennas for 5GHz of which 2 are also used for 2.4GHz.+The Cudy WR2100 is an 802.11ac 4×4:4 Gigabit MediaTek-based access point. It has five 1 Gbps Ethernet ports. It uses 4 external antennas for 5GHz of which 2 are also used for 2.4GHz.
  
 {{ :media:cudy:wr2100:external.png?nolink&200 |}} {{ :media:cudy:wr2100:external.png?nolink&200 |}}
Line 48: Line 48:
  
 ===== Returning to OEM firmware ===== ===== Returning to OEM firmware =====
-Returning to the stock Cudy firmware from the OpenWrt installation is possible using TFTP as described [[https://www.cudytech.com/newsinfo/1040412.html|here]].+Returning to the stock Cudy firmware from the OpenWrt installation is possible using TFTP, using  [[https://www.cudytech.com/filedownload/282847|this]] image. TFTP server should be configured with 192.168.1.88 as IP address.
  
-==== Photos ====+  - Press the "Reset" button and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the "Reset" button.  
 +  - Power on the Cudy router.  
 +  - You can release the reset button only when the status LED flashes red and blue quickly, or when TFTP starts downloading firmware. 
 + 
 +==== Flash Layout ==== 
 + 
 +The following flash partitions were found using /proc/mtd: 
 + 
 +^ dev    ^ size       ^ erasesize   ^ name        ^ 
 +| mtd0   | 00030000   | 00010000    | u-boot      | 
 +| mtd1   | 00010000   | 00010000    | u-boot-env 
 +| mtd2   | 00010000   | 00010000    | factory     | 
 +| mtd3   | 00f80000   | 00010000    | firmware    | 
 +| mtd4   | 00281614   | 00010000    | kernel      | 
 +| mtd5   | 00cfe9ec   | 00010000    | rootfs      | 
 +| mtd6   | 009a0000   | 00010000    | rootfs_data | 
 +| mtd7   | 00010000   | 00010000    | debug       | 
 +| mtd8   | 00010000   | 00010000    | backup      | 
 +| mtd9   | 00010000   | 00010000    | bdinfo      | 
 + 
 +==== Serial ==== 
 + 
 +R4 & R5 need to be shorted (0-100Ω) for the UART to work. 
 + 
 +{{:media:cudy:wr2100:serial_connections.jpeg?nolink&400|}} 
 + 
 +Use 115200 baud 8N1. 
 + 
 +===== Photos =====
  
 //PCB Front://\\ //PCB Front://\\
  • Last modified: 2024/02/12 10:03
  • by 127.0.0.1