Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:cudy:cudy_wr2100_v1 [2021/11/08 16:56] – include hardware highlights elcovv | toh:cudy:cudy_wr2100_v1 [2021/11/13 19:24] – [Serial] elcovv | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Cudy WR2100 | + | ====== Cudy WR2100 ====== |
| - | The EAP235-Wall | + | The Cudy WR2100 |
| - | + | ||
| - | It uses 4 external antennas for 5GHz of which 2 are also used for 2.4GHz. | + | |
| + | {{ : | ||
| ===== Initial Notes and Warning ===== | ===== Initial Notes and Warning ===== | ||
| - | It is [[https:// | + | It is [[https:// |
| ===== Supported versions ===== | ===== Supported versions ===== | ||
| Line 32: | Line 31: | ||
| sort : version | sort : version | ||
| ---- | ---- | ||
| + | |||
| + | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel_releasecurrent, | ||
| + | headers : Model, Version, OpenWrt Release, OpenWrt Factory Firmware, OpenWrt Sysupgrade Firmware, OEM Stock Firmware | ||
| + | align : l,c,c | ||
| + | filter | ||
| + | sort : version | ||
| + | ---- | ||
| + | |||
| + | → [[docs: | ||
| + | |||
| + | ==== Installation using web interface ==== | ||
| + | |||
| + | Cudy provides a version of OpenWrt 21.02.1 that can be downloaded [[https:// | ||
| + | |||
| + | ===== Returning to OEM firmware ===== | ||
| + | Returning to the stock Cudy firmware from the OpenWrt installation is possible using TFTP, using [[https:// | ||
| + | |||
| + | - Press the " | ||
| + | - Power on the Cudy router. | ||
| + | - You can release the reset button only when the status LED flashes red and blue quickly, or when TFTP starts downloading firmware. | ||
| + | |||
| + | ==== Flash Layout ==== | ||
| + | |||
| + | The following flash partitions were found using /proc/mtd: | ||
| + | |||
| + | ^ dev ^ size ^ erasesize | ||
| + | | mtd0 | 00030000 | ||
| + | | mtd1 | 00010000 | ||
| + | | mtd2 | 00010000 | ||
| + | | mtd3 | 00f80000 | ||
| + | | mtd4 | 00281614 | ||
| + | | mtd5 | 00cfe9ec | ||
| + | | mtd6 | 009a0000 | ||
| + | | mtd7 | 00010000 | ||
| + | | mtd8 | 00010000 | ||
| + | | mtd9 | 00010000 | ||
| + | |||
| + | ==== Serial ==== | ||
| + | |||
| + | R4 & R5 need to be shorted (0-100Ω) for the UART to work. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | Use 115200 baud 8N1. | ||
| + | |||
| + | ===== Photos ===== | ||
| + | |||
| + | //PCB Front://\\ | ||
| + | {{: | ||
| + | |||
| + | //PCB Back://\\ | ||
| + | {{: | ||
| + | |||
| + | //Backside label://\\ | ||
| + | {{: | ||
| + | |||