User Tools

Site Tools


toh:comtrend:vr3032u

Comtrend VR-3032u

GPL Source Code (Comtrend)

Not supported (WIP).

Installation

Flashing ANY Firmware

  1. You must set your TCP/IP v4 protocol to:
    • IP: 192.168.1.2
    • Netmask: 255.255.255.0
    • Gateway: 192.168.1.1
    • DNS: (optional, can be blank).
  2. Power off the router.
  3. Press reset button near the antenna.
  4. Keep it pressed while powering up during ~20+ seconds.
  5. Acces to http://192.168.1.1 and upload binary file.
  6. Wait until router reboots.

Hardware

Info

Architecture MIPS
Vendor Broadcom
bootloader cfe
Board ID 963168M-1841N1
System-On-Chip Broadcom BCM63168
CPU/Speed BMIPS4350 v8.0 / 400 MHz
NAND 128 MiB (MX30LF1G08AA-TI)
RAM 64 MiB / DDR2 (EM68816CWQD-25H)
Wireless BCM6362 (14e4:6362) 802.11b/g/n (SoC)
Antenna 2x
Ethernet Integrated BCM63168 w/ vlan support swconfig
USB Yes
Power adapter 12V DC 1A / UP0121B-12PE
Serial Yes
JTAG ?

Photos

Case:

Board:

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

PCB with markings for serial connection

Bootlogs

OEM Bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 SIZ1 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN FPS0 BT01 0002 STOP NAN9 NAN3 RFS1 NAN5 CFE version 1.0.38-112.118-11 for BCM963268 (32bit,SP,BE) Build Date: å12月 27 11:54:52 CST 2012 (camille@SW1-BCM-02) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0xc2f1 block 128KB size 131072KB Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-28) : 963168M-1841N1 Number of MAC Addresses (1-32) : 32 Base MAC Address : f8:8e:85:ed:70:d3 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 WLAN Password : 93ydNwyxeEiqzXKtUSgd Serial Number : 1463032UXXF-AA002895 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from only image (0xb8020000) ... nand_flash_read_buf(): Attempt to read bad nand block 1 nand_flash_read_buf(): Attempt to read bad nand block 1 Decompression OK! Entry at 0x802e5950 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x802e5950 Linux version 2.6.30 (joba@SW1-BCM-02) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Wed Apr 3 09:57:13 CST 2013 BCM Flash API. Flash device is not found. 963168M-1841N1 prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 80384c90, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59696k/64312k available (2934k kernel code, 4596k reserved, 623k data, 148k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Apr 3 2013 09:54:51 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 828 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00009081-00008a7e=1539>=300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Apr 3 2013 09:57:00 initialized Broadcom GBPM v0.1 Apr 3 2013 09:57:01 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 116 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=c2f1801d After: NandSelect=40000001, nandConfig=15142200 DevId c2f1801d may not be supported. Will use config info Spare Area Size = 16B/512B Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 ECC level changed to 15 OOB size changed to 16 BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=c2f1801d, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a38198, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 nand_read_bbt: Bad block at 0x00020000 nand_read_bbt: Bad block at 0x02a40000 nand_read_bbt: Bad block at 0x06740000 nand_read_bbt: Bad block at 0x07320000 brcmnandCET: Status -> Deferred brcmnand_scan 99 Creating 4 MTD partitions on "brcmnand.0": 0x000000020000-0x000003d80000 : "rootfs" 0x000003d80000-0x000007ae0000 : "rootfs_update" 0x000007b00000-0x000007f00000 : "data" 0x000000000000-0x000000020000 : "nvram" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0xc007 is enabled PCIe: No device found - Powering down Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Apr 3 2013 09:56:47 GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 148k freed init started: BusyBox v1.17.2 (2013-04-03 09:59:22 CST) starting pid 222, tty '': '/etc/init.d/rcS' usbfs: unrecognised mount option "defaults" or missing value usbfs: mount parameter error. mount: mounting /dev/sda1 on /mnt failed: No such device or address starting pid 232, tty '': '-/bin/sh' BusyBox v1.17.2 (2013-04-03 09:59:22 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... -/bin/sh: ct_hotplug_monitor: not found chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Apr 3 2013 09:55:30 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4766, buf size=2112 Broadcom BPM Module Char Driver v0.1 Apr 3 2013 09:55:24 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Apr 3 2013 09:55:31 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Apr 3 2013 09:55:31 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 3 2013 09:55:25 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa2a5b200 0xa2a9b200 Allocated FAP0 TM SDRAM Queue Storage (a2a614bc) : 219456 bytes @ a2ac0000 Allocated FAP1 TM SDRAM Queue Storage (a2aa14bc) : 219456 bytes @ a2b00000 [NTC fapProto] fapReset : Reset FAP Protocol layer fapDrv_construct: FAP0: pManagedMemory=b0820710. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20710. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6432>, free <224>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6432>, free <224>, total<8192> [FAP0] PSM : addr<0x80002000>, used <24412>, free <164>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24412>, free <164>, total <24576> [FAP0] Flows supported: 222 (dsp 54, psm 44, qsm 124) [FAP1] Flows supported: 222 (dsp 54, psm 44, qsm 124) [FAP0] DQM : availableMemory 15464 bytes, nextByteAddress 0xE0010398 [FAP1] DQM : availableMemory 15464 bytes, nextByteAddress 0xE0010398 [FAP0] GSO Buffer set to 0x00000000 [FAP1] GSO Buffer set to 0x00000000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM63168D0 Ethernet Network Device v0.1 Apr 3 2013 09:56:41 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b0820710 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0820710 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a20710 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0a20710 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b08216b0 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb08216b0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a216b0 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a216b0 For port 3; changing the MII adv to 0x1e1 changing the GMII adv to 0x0 Error: kerSysRegisterDyingGaspHandler: list head is null eth1: MAC Address: F8:8E:85:ED:70:D3 eth2: MAC Address: F8:8E:85:ED:70:D3 eth3: MAC Address: F8:8E:85:ED:70:D3 eth0: MAC Address: F8:8E:85:ED:70:D3 [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Adress Resolution Logic Processor (ARL) Char Driver v0.1 Apr 3 2013 09:55:23 Registered <245> [ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP0 [ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0820024)=0x00005f5c / 0x00005f4c [ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0820028)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b08206f4)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0823208)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0823210)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0c04000)=0x00005f5c / 0x0000c398 [ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0c10394)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP1 [ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0a20024)=0x00005f5c / 0x00005f4c [ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0a20028)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b0a206f4)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0a23208)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0a23210)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0e04000)=0x00005f5c / 0x0000c398 [ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0e10394)=0x12345678 / 0x12345678 --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3097 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2008.cpe4.12L06B.4 Error: kerSysRegisterDyingGaspHandler: list head is null Broadcom 802.1Q VLAN Interface, v0.1 usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems hso_init - tty_register_driver failed(-16) insmod: can't insert '/lib/modules/2.6.30/kernel/drivers/usb/serial/hso.ko': Device or resource busy ===== Comtrend Release Version VA31-412JAZ-C03_R01 ===== killall: syslogd: no process killed Energy Efficient Ethernet is disabled smtpEnblSsl 0 Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state BcmAdsl_Initialize=0xC01F8C60, g_pFnNotifyCallback=0xC022EF24 WLmngr Daemon is running optarg=0 shmId=0 wlevt is ready for new msg... lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x7FF1F3F9 0x7FF3FFFB *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xE4C54 => 0x11B4C0 *** AdslCoreSharedMemInit: shareMemSize=92957(92960) AdslCoreHwReset: pLocSbSta=81d80000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FA3F70 ***BcmDiagsMgrRegisterClient: 0 ***Error: kerSysRegisterDyingGaspHandler: list head is null fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22980 bytes remaining 584 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22980 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fc0 bytes remaining 456 XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fc0 bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system bcmxtmcfg: gulBondDslMonitorValid = 1 Register interface ppp0.1 !! ssk:error:31.009:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server ssk:error:31.010:rcl_wanPppConnPortmappingObject:113Register interface ppp1.1 !! :This is system bootup, so don't add the Virtual Server ssk:error:31.027:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server ssk:error:31.028:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server monitor task is initialized pid= 347 There is no Predefined DevicePin in CFE WPS Device PIN = 96567111 br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state Setting SSID: "JAZZTEL_70D4" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state Offset1:131072 Offset2:64487424 acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b01


Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/comtrend/vr3032u.txt · Last modified: 2019/10/03 10:31 by tmomas