Comtrend VG-8050

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

  1. You must set your TCP/IP v4 protocol to:
    • IP: 192.168.1.2
    • Netmask: 255.255.255.0
    • Gateway: 192.168.1.1
    • DNS: (optional, can be blank).
  2. Power off the router.
  3. Press reset button near the antenna.
  4. Keep it pressed while powering up during ~20+ seconds.
  5. Acces to http://192.168.1.1, you should see this screen:
  6. Upload the binary file.
  7. Wait until router reboots.
Architecture MIPS
Vendor Broadcom
bootloader cfe
Board ID 963169P-1861N5
System-On-Chip Broadcom BCM63169
CPU/Speed BMIPS4350 v8.0 / 400 MHz
NAND 128 MiB (MX30LF1G08AA)
RAM 128 MiB / DDR2 (EM68C16CWQE)
Wireless BCM6362 (14e4:6362) 802.11b/g/n (SoC)
Antenna 2x
Ethernet Broadcom BCM53125 w/ vlan support swconfig
USB mod
FXS/VoIP LE89116 QVC
Power adapter 12V DC 2A / I.T.E. AMS4-1202000FV
Serial Yes
JTAG No

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
vg8050_serial.jpg

This board unlike other BCM63168 boards uses a dedicated BCM53125 Gigabit switch (other boards use the internal fast ethernet switch at the SoC).

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN NAN0 BT07 0001 NAN9 BT08 0492 NAN9 NAN3 RFS2 NAN5 CFE version 1.0.38-112.70-15 for BCM963268 (32bit,SP,BE) Build Date: 2013-02-25 18:55:44 (dylan@rd7-server) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0xc2f1 block 128KB size 131072KB External switch id = 53125 Chip ID: BCM63169D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-15) : 963169P-1861N5 Number of MAC Addresses (1-32) : 32 Base MAC Address : f8:8e:85:xx:xx:xx PSI Size (1-64) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 WLAN Password : u9hi36M9F8bJjCk8cQDx Serial Number : F88E85DA8D7C Voice Board Configuration (0-0) : 8050TLF_VE890 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from latest image (0xbbd80000) ... Decompression OK! Entry at 0x8032ae10 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x8032ae10 Linux version 2.6.30 (yanyang@rd7-server) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Wed Jan 29 13:38:58 CST 2014 BCM Flash API. Flash device is not found. 963169P-1861N5 prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 07ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00007ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00007ece On node 0 totalpages: 32462 free_area_init_node: node 0, pgdat 80403c10, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 222 pages used for memmap Normal zone: 28144 pages, LIFO batch:7 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 512 (order: 9, 2048 bytes) console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Memory: 124004k/129848k available (3212k kernel code, 5672k reserved, 853k data, 152k init, 0k highmem) Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Jan 29 2014 13:34:56 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1144 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00009040-00008a58=1512>=300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Jan 29 2014 13:38:25 initialized Broadcom GBPM v0.1 Jan 29 2014 13:38:25 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 242 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=c2f1801d After: NandSelect=40000001, nandConfig=15142200 DevId c2f1801d may not be supported. Will use config info Spare Area Size = 16B/512B Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 ECC level changed to 15 OOB size changed to 16 BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=c2f1801d, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=87a3f590, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 nand_read_bbt: Bad block at 0x02700000 nand_read_bbt: Bad block at 0x04760000 nand_read_bbt: Bad block at 0x04e40000 nand_read_bbt: Bad block at 0x05fc0000 nand_read_bbt: Bad block at 0x07d20000 brcmnandCET: Status -> Deferred brcmnand_scan 99 Creating 4 MTD partitions on "brcmnand.0": 0x000003d80000-0x000007ae0000 : "rootfs" 0x000000020000-0x000003d80000 : "rootfs_update" 0x000007b00000-0x000007f00000 : "data" 0x000000000000-0x000000020000 : "nvram" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0xc007 is enabled SES: FAIL LED GPIO 0xc00e is enabled /proc/wifi5gwps created /proc/wifi5genable created PCIe: No device found - Powering down Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1200 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 152k freed init started: BusyBox v1.17.2 (2014-01-29 13:42:38 CST) starting pid 222, tty '': '/etc/init.d/rcS' starting pid 228, tty '': '-/bin/sh' BusyBox v1.17.2 (2014-01-29 13:42:38 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Jan 29 2014 13:36:47 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132659B (19MB), num of buffers=9605, buf size=2096 Broadcom BPM Module Char Driver v0.1 Jan 29 2014 13:35:23 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jan 29 2014 13:36:47 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jan 29 2014 13:36:47 chipId 0x631690D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jan 29 2014 13:36:37 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Allocated FAP0 GSO Buffers (0xA5C7D484) : 1048576 bytes @ 0xA5D00000 Allocated FAP1 GSO Buffers (0xA5C9D484) : 1048576 bytes @ 0xA5E00000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7104>, free <64>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7104>, free <64>, total<8192> [FAP0] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP0] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP1] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP0] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP1] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP0] GSO Buffer set to 0xA5D00000 [FAP1] GSO Buffer set to 0xA5E00000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. bcmPktDma_bind: FAP Driver binding successfull CT_HOTPLUG_MONITOR Broadcom BCM63169D0 Ethernet Network Device v0.1 Jan 29 2014 13:38:00 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b08206f0 bytes remaining 7008 ETH Init: Ch:0 - 200 tx BDs at 0xb08206f0 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a206f0 bytes remaining 7008 ETH Init: Ch:1 - 200 tx BDs at 0xb0a206f0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821690 bytes remaining 2192 ETH Init: Ch:0 - 600 rx BDs at 0xb0821690 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21690 bytes remaining 2192 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21690 bcmsw_spi_select: SPIF set, not ready @@@@@ Doing HPNA Reset @@@@@ [Comtrend]INFO: vport_cnt=6, phyid=0, eth=4 eth4: MAC Address: F8:8E:85:DA:8D:7C [Comtrend]INFO: vport_cnt=6, phyid=1, eth=3 eth3: MAC Address: F8:8E:85:DA:8D:7C [Comtrend]INFO: vport_cnt=6, phyid=2, eth=2 eth2: MAC Address: F8:8E:85:DA:8D:7C [Comtrend]INFO: vport_cnt=6, phyid=3, eth=1 eth1: MAC Address: F8:8E:85:DA:8D:7C [Comtrend]INFO: vport_cnt=6, phyid=4, eth=0 eth0: MAC Address: F8:8E:85:DA:8D:7C [Comtrend]INFO: vport_cnt=6, phyid=5, eth=5 eth5: MAC Address: F8:8E:85:DA:8D:7C [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Adress Resolution Logic Processor (ARL) Char Driver v0.1 Jan 29 2014 13:35:23 Registered <245> --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=6243 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2008.cpe4.12L04.3 Endpoint: endpoint_init entry Endpoint: endpoint_init COMPLETED Broadcom 802.1Q VLAN Interface, v0.1 usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems hso_init - tty_register_driver failed(-16) insmod: can't insert '/lib/modules/2.6.30/kernel/drivers/usb/serial/hso.ko': Device or resource busy ===== Comtrend Release Version SB01-S412TLF-C07_R03 (build timestamp 140129_1339) ===== ssk:error:20.632:main:206:@@@@@ (main:206) board id(963169P-1861N5), activate VoIP!! @@@@@ -- Delete 0 WANDelegated Prefix -- BOS: Enter bosInit BOS: Exit bosInit endpoint_open COMPLETED --rcl_uploadDiagnosticsObject 232-- default gw:br0 --rcl_downloadDiagnosticsObject 134-- default gw:ppp0 Tue Jan 1 00:00:00 UTC 2013 ip_tables: (C) 2000-2006 Netfilter Core Team ip6_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack_netlink: Unknown symbol __nf_ct_l4proto_find nf_conntrack_netlink: Unknown symbol nf_conntrack_find_get nf_conntrack_netlink: Unknown symbol nf_conntrack_register_notifier nf_conntrack_netlink: Unknown symbol nfnetlink_parse_nat_setup_hook nf_conntrack_netlink: Unknown symbol __nf_ct_try_assign_helper nf_conntrack_netlink: Unknown symbol nf_ct_helper_ext_add nf_conntrack_netlink: Unknown symbol nf_conntrack_untracked nf_conntrack_netlink: Unknown symbol __nf_ct_ext_add nf_conntrack_netlink: Unknown symbol nf_conntrack_unregister_notifier nf_conntrack_netlink: Unknown symbol nf_ct_l3protos nf_conntrack_netlink: Unknown symbol __nf_ct_expect_find nf_conntrack_netlink: Unknown symbol nf_conntrack_chain nf_conntrack_netlink: Unknown symbol nf_conntrack_htable_size nf_conntrack_netlink: Unknown symbol nf_conntrack_flush nf_conntrack_netlink: Unknown symbol nf_conntrack_alloc nf_conntrack_netlink: Unknown symbol nf_ct_expect_related_report nf_conntrack_netlink: Unknown symbol nf_ct_expect_hsize nf_conntrack_netlink: Unknown symbol nf_ct_expect_alloc nf_conntrack_netlink: Unknown symbol nf_ct_expect_put nf_conntrack_netlink: Unknown symbol nf_ct_expect_find_get nf_conntrack_netlink: Unknown symbol __nf_ct_kill_acct nf_conntrack_netlink: Unknown symbol nf_ct_expect_unregister_notifier nf_conntrack_netlink: Unknown symbol nf_conntrack_lock nf_conntrack_netlink: Unknown symbol nf_ct_expect_register_notifier nf_conntrack_netlink: Unknown symbol __nf_conntrack_find nf_conntrack_netlink: Unknown symbol nf_ct_unlink_expect nf_conntrack_netlink: Unknown symbol nf_conntrack_free nf_conntrack_netlink: Unknown symbol __nf_conntrack_helper_find_byname nf_conntrack_netlink: Unknown symbol nf_conntrack_hash_insert nf_conntrack_netlink: Unknown symbol nf_conntrack_l3proto_generic nf_conntrack_netlink: Unknown symbol nf_ct_unexpect_related nf_conntrack_netlink: Unknown symbol nf_ct_remove_expectations insmod: can't insert '/lib/modules/2.6.30/kernel/net/netfilter/nf_conntrack_netlink.ko': unknown symbol in module, or unknown parameter nf_conntrack version 0.5.0 (2028 buckets, 8112 max) RADVDAdvLinkMTUUserMode[0] mtu:1492 device eth1 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 ADDRCONF(NETDEV_UP): eth1: link is not ready ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4200 MASK = 0x0008 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0100 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0000 device eth2 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 ADDRCONF(NETDEV_UP): eth2: link is not ready ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4200 MASK = 0x0004 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0100 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0000 device eth3 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 ADDRCONF(NETDEV_UP): eth3: link is not ready ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4200 MASK = 0x0002 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0100 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0000 device eth4 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 ADDRCONF(NETDEV_UP): eth4: link is not ready ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4200 MASK = 0x0001 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0100 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0000 [ll] EUI-64 mdoe device eth5 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 ADDRCONF(NETDEV_UP): eth5: link is not ready ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4200 MASK = 0x0020 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0100 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0000 [ll] EUI-64 mdoe rcl_wlBaseCfgObject@610 Create Obj:: device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### RADVDAdvLinkMTUUserMode[0] mtu:1492 br0: port 6(wl0) entering forwarding state WLmngr Daemon is running optarg=0 shmId=0 wlevt is ready for new msg... not enable and not disable the igmp snooping... RADVDAdvLinkMTUUserMode[0] mtu:1492 RADVDAdvLinkMTUUserMode[0] mtu:1492 ######## ethsw_BCM53115_set_wanoe_portmap:4186 ####### set BCM53115 WAN_REG = 0x4210 MASK = 0x0010 ######## ethsw_BCM53115_set_wanoe_portmap:4201 ####### set BCM53115 DISABLE_LEARN_REG = 0x0110 ######## ethsw_BCM53115_set_wanoe_portmap:4234 ####### IGNORE_PAUSE_FRAME_TX=0x0000 ######## ethsw_BCM53115_set_wanoe_portmap:4245 ####### IGNORE_PAUSE_FRAME_TX=0x0010 ADDRCONF(NETDEV_UP): eth0: link is not ready Register interface eth0.2 !! Register interface ppp0.1 !! ssk:error:33.795:stopSamba:559:Samba is not running. killall: smbd: no process killed ssk:error:33.830:stopSamba:570:NETBIOS is not running. killall: nmbd: no process killed ctnetlink v0.93: registering with nfnetlink. #### wlmngr_retrieve 0 There is no Predefined DevicePin in CFE WPS Device PIN = 19117652 #### wlReadMdmM ret 0 monitor task is initialized pid= 341 br0: port 6(wl0) entering disabled state device wl0 left promiscuous mode br0: port 6(wl0) entering disabled state #### Brctl_Port_Base_VLAN_config:46 #### device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### br0: port 6(wl0) entering forwarding state The file(/var/donglemap2) is not exist. ssk:error:36.779:initVodslBoundIpIfWanSideUpLocked:728:Failed to get WAN Connection object Note: Loading 6300 MDK (default) driver for 63169 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x0; config_pbmp = 0x40 Received response to CMS_MSG_REGISTER_EVENT_INTEREST from SMD Switch MDK link poll thread: unit=1; phypbmp=0x3f br0: port 6(wl0) entering disabled state ####ethsw_BCM53115_set_mac:4336 write 0x5B to 0x5D#### eth5 (switch port: 5) Link UP 10 mbps half duplex ADDRCONF(NETDEV_CHANGE): eth5: link becomes ready br0: port 5(eth5) entering forwarding state [DEBUG] wlLockWriteMdmOne: wl0 is initialized for the first time RADVDAdvLinkMTUUserMode[0] mtu:1492 Setting SSID: "MOVISTAR_8D7C" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" device wl0 left promiscuous mode br0: port 6(wl0) entering disabled state #### Brctl_Port_Base_VLAN_config:46 #### device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:46 #### br0: port 6(wl0) entering forwarding state acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... Wan link(3G) went from up->down, send event msg 3G WAN not configured acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b0b pid 24's current scheduling policy: SCHED_OTHER pid 24's current scheduling priority: 0 pid 24's new scheduling policy: SCHED_RR pid 24's new scheduling priority: 5 RADVDAdvLinkMTUUserMode[0] mtu:1492 [14:00] = 11 40 [14:00] = 11 40 ##### 2.4g finished BCM963268 Broadband Router


HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN NAN0 BT19 0001 NAN9 BT18 0492 NAN9 NAN3 RFS1 NAN5 CFE version 1.0.38-112.70-20 for BCM963268 (32bit,SP,BE) Build Date: 2014-09-23 15:12:29 (jim@SW1-BCM-04) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0xc2f1 block 128KB size 131072KB External switch id = 53125 Chip ID: BCM63169D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.4:ffffff00 Host IP address : 192.168.1.8 Gateway IP address : 192.168.1.1 Run from flash/host (f/h) : f Default host run file name : vg8050.elf Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-15) : 963169P-1861N5 Number of MAC Addresses (1-32) : 32 Base MAC Address : f8:8e:85:da:8d:7c PSI Size (1-64) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 WLAN Password : u9hi36M9F8bJjCk8cQDx Serial Number : F88E85DA8D7C Voice Board Configuration (0-0) : 8050TLF_VE890 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from latest image (0xb8020000) ... Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 5.4.43 (noltari@skynet) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12787-af5ccfbac7)) #0 SMP Wed Jun 3 16:50:58 2020 [ 0.000000] Detected Broadcom 0x63268 CPU revision d0 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 128MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.38-112.70-14 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a080 (Broadcom BMIPS4350) [ 0.000000] board: board name: 963169P-1861N5 [ 0.000000] MIPS: machine is Comtrend VG-8050 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26048 r8192 d23104 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: rootfstype=squashfs,ubifs noinitrd console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 121020K/131072K available (5692K kernel code, 216K rwdata, 1216K rodata, 1316K init, 206K bss, 10052K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x338/0x564 with crng_init=0 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008128] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.046443] pid_max: default: 32768 minimum: 301 [ 0.051522] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059056] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.071839] rcu: Hierarchical SRCU implementation. [ 0.077949] smp: Bringing up secondary CPUs ... [ 0.084111] SMP: Booting CPU1... [ 7.775020] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 7.775037] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 7.775317] CPU1 revision is: 0002a080 (Broadcom BMIPS4350) [ 0.119612] Synchronize counters for CPU 1: [ 0.119632] SMP: CPU1 is running [ 0.119651] done. [ 0.150159] smp: Brought up 1 node, 2 CPUs [ 0.165477] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.175532] futex hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.182708] pinctrl core: initialized pinctrl subsystem [ 0.189076] NET: Registered protocol family 16 [ 0.270611] clocksource: Switched to clocksource MIPS [ 0.278616] NET: Registered protocol family 2 [ 0.284452] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.293164] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.301094] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.308415] TCP: Hash tables configured (established 1024 bind 1024) [ 0.315378] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.322197] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.329914] NET: Registered protocol family 1 [ 0.334453] PCI: CLS 0 bytes, default 16 [ 0.345578] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.365726] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.371739] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.395516] random: fast init done [ 0.411811] bcm63268-pinctrl 100000c0.pin-controller: registered at mmio (ptrval) [ 0.420489] 10000180.serial: ttyS0 at MMIO 0x10000180 (irq = 13, base_baud = 1562500) is a bcm63xx_uart [ 0.430222] printk: console [ttyS0] enabled [ 0.430222] printk: console [ttyS0] enabled [ 0.438793] printk: bootconsole [early0] disabled [ 0.438793] printk: bootconsole [early0] disabled [ 0.459490] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.466072] nand: Macronix NAND 128MiB 3,3V 8-bit [ 0.470885] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.478712] bcm6368_nand 10000200.nand: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, Hamming ECC [ 0.490628] Bad block table found at page 65472, version 0x01 [ 0.497217] Bad block table found at page 65408, version 0x01 [ 0.503767] nand_read_bbt: bad block at 0x000002700000 [ 0.509058] nand_read_bbt: bad block at 0x000004760000 [ 0.514340] nand_read_bbt: bad block at 0x000004e40000 [ 0.519599] nand_read_bbt: bad block at 0x000005fc0000 [ 0.524881] nand_read_bbt: bad block at 0x000007d20000 [ 0.531012] 2 fixed-partitions partitions found on MTD device brcmnand.0 [ 0.537938] Creating 2 MTD partitions on "brcmnand.0": [ 0.543217] 0x000000000000-0x000000020000 : "cferom" [ 0.550033] 0x000000020000-0x000007ae0000 : "wfi" [ 0.643087] cferam: bootflag1=119 [ 0.646467] cferam: bootflag2=118 [ 0.807870] 5 bcm-wfi-split-fw partitions found on MTD device wfi [ 0.814119] Creating 5 MTD partitions on "wfi": [ 0.818781] 0x000000000000-0x000000140000 : "cferam" [ 0.825678] 0x000000140000-0x000003d60000 : "firmware" [ 0.833057] 0x000000140000-0x000000640000 : "kernel" [ 0.839882] 0x000000640000-0x000003d60000 : "ubi" [ 0.846893] 0x000003d60000-0x000007ac0000 : "img2" [ 0.864240] bcm63xx-spi 10000800.spi: at [mem 0x10000800-0x10000f0b flags 0x200] (irq 88, FIFOs size 542) [ 0.895139] b53_common: found switch: BCM53125, rev 4 [ 0.901239] libphy: Fixed MDIO Bus: probed [ 0.945771] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.954436] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 0.961589] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 0.968745] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 0.975910] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 0.983077] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 0.992416] NET: Registered protocol family 10 [ 1.008394] Segment Routing with IPv6 [ 1.012414] NET: Registered protocol family 17 [ 1.017055] 8021q: 802.1Q VLAN Support v1.8 [ 1.043074] UBI: auto-attach mtd5 [ 1.046576] ubi0: attaching mtd5 [ 1.073619] UBI: EOF marker found, PEBs from 18 will be erased [ 1.080492] ubi0: scanning is finished [ 1.124140] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 401 LEBs [ 1.132844] ubi0: attached mtd5 (name "ubi", size 55 MiB) [ 1.138422] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.145470] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.152450] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.159619] ubi0: good PEBs: 440, bad PEBs: 1, corrupted PEBs: 0 [ 1.165802] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 1.173241] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1591203982 [ 1.182648] ubi0: available PEBs: 0, total reserved PEBs: 440, PEBs reserved for bad PEB handling: 19 [ 1.192200] ubi0: background thread "ubi_bgt0d" started, PID 407 [ 1.196179] block ubiblock0_0: created from ubi0:0(rootfs) [ 1.204101] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 1.229076] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.255550] Freeing unused kernel memory: 1316K [ 1.260224] This architecture does not have kernel memory protection. [ 1.266853] Run /sbin/init as init process [ 2.368486] init: Console is alive [ 2.372323] init: - watchdog - [ 3.073624] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.204463] usbcore: registered new interface driver usbfs [ 3.210330] usbcore: registered new interface driver hub [ 3.215936] usbcore: registered new device driver usb [ 3.233046] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.241790] ehci-fsl: Freescale EHCI Host controller driver [ 3.249746] ehci-platform: EHCI generic platform driver [ 3.362327] ehci-platform ehci-platform: EHCI Host Controller [ 3.368283] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 3.376763] ehci-platform ehci-platform: irq 18, io mem 0xb0002500 [ 3.398300] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 3.407945] hub 1-0:1.0: USB hub found [ 3.411968] hub 1-0:1.0: 2 ports detected [ 3.425718] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.433924] ohci-platform: OHCI generic platform driver [ 3.439570] ohci-platform ohci-platform: Generic Platform OHCI controller [ 3.446622] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 3.454944] ohci-platform ohci-platform: irq 17, io mem 0xb0002600 [ 3.523770] hub 2-0:1.0: USB hub found [ 3.527767] hub 2-0:1.0: 2 ports detected [ 3.533546] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.544343] init: - preinit - [ 4.305454] random: crng init done [ 6.033552] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.022306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.541936] UBIFS (ubi0:1): default file-system created [ 10.548800] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 10.555093] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 533 [ 10.688869] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 10.696950] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.707158] UBIFS (ubi0:1): FS size: 49647616 bytes (47 MiB, 391 LEBs), journal size 2539520 bytes (2 MiB, 20 LEBs) [ 10.717884] UBIFS (ubi0:1): reserved for root: 2344978 bytes (2290 KiB) [ 10.724697] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 77AE05AD-61A4-4360-A74B-DB7903F9234B, small LPT model [ 10.739729] mount_root: overlay filesystem has not been fully initialized yet [ 10.747825] mount_root: switching to ubifs overlay [ 10.785360] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 10.799753] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.009266] procd: - early - [ 11.012471] procd: - watchdog - [ 11.677242] procd: - watchdog - [ 11.680871] procd: - ubus - [ 11.891405] procd: - init - Please press Enter to activate this console. [ 12.869976] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.062821] xt_time: kernel timezone is -0000 [ 13.108865] PPP generic driver version 2.4.2 [ 13.116625] NET: Registered protocol family 24 [ 13.145036] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.178547] urngd: v1.0.2 started. [ 38.569908] br-lan: port 1(eth0.1) entered blocking state [ 38.575610] br-lan: port 1(eth0.1) entered disabled state [ 38.581977] device eth0.1 entered promiscuous mode [ 38.586979] device eth0 entered promiscuous mode [ 38.607908] br-lan: port 1(eth0.1) entered blocking state [ 38.613513] br-lan: port 1(eth0.1) entered forwarding state [ 39.567057] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Required materials

  • 1 x LM7805 (Voltage regulator, consider a step-down model)
  • 1 x Electrolytic capacitor 10-470uF 25V
  • 2 x Resistors 4K7 0,25W
  • 1 x USB Connector

You need to add 2x 4K7 resistors behind the SoC heat sink:

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1