Comtrend AR-5381u

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.
See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

Supported Versions

Hardware Highlights

Installation

Other

Firmware download link notes
OEM firmware AR-5381u-A731-410JAZ-C05_R01.bin Original firmware from Jazztel ISP
Netcomm custom NB604N-NZ-R4B016-CUSTOM_(AR5381u-AR5387un).bin Custom firmware from Netcomm NB604N GPL

Flashing ANY Firmware

You must set your TCP/IP v4 protocol at your computer to:

  1. IP: 192.168.1.2
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1
  4. DNS: (optional, can be blank).

Then:

  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Acces to http://192.168.1.1 and upload binary file.
  5. Wait until router reboots.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
eth0 LAN ports (0 to 3) bridged
wlan0 WiFi bridged (disabled)

Switch Ports (for VLANs)

This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself. Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.

Port Switch port Mode
LAN1X 0 lan
LAN2X 1 lan
LAN3X 2 lan
LAN4X 3 Internet (WAN) 
# 
config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fda5:ace8:376d::/48'

config interface 'lan'
        option ifname 'eth0.1'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'wan'
        option ifname 'eth0.2'
        option proto 'dhcp'
        
config switch
        option name 'eth0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'eth0'
        option vlan '1'
        option ports '0 1 2 8t'

config switch_vlan
        option device 'eth0'
        option vlan '2'
        option ports '3 8t'

Hardware

Info

Instruction set MIPS
Vendor Broadcom
bootloader cfe
Board ID 96328A-1241N
System-On-Chip Broadcom BCM6328
CPU @Frq BMIPS4350 V7.5 @320 MHz
Flash-Chip MX25L12845EMI-10G (SPI) / 64KB block size x 256 main blocks
Flash size 16 MiB
RAM-Chip EM68B16CWPA-25H / DDR2-800
RAM size 64 MiB
Wireless BCM43225 (14e4:a8d8) 802.11b/g/n (onboard)
Ethernet Internal BRCM6328 Switch, 4x 100M + ADSL2+
USB 1x 2.0
Serial Yes
JTAG ?

Photos

FIXME Add photo of front and back of the casing

Opening the case

Note: This will void your warranty!

  • Describe how to open the cover.

Main PCB:

ar-5381u_board_up.jpg ar-5381u_board_down.jpg

Wifi

BCM43225 802.11b/g/n onboard wifi, 2x PCB non-detachable antennas inside the case.

In OpenWrt the kmod-b43 driver is used by default, therefore N mode isn't available. kmod-brcmsmac supports N mode, see Broadcom BCM47xx.

No physical EEPROM at the board, nor partition reserverd for this data at the flash chip. In theory, in the original firmware, the EEPROM is taken from the file /etc/wlan/bcm43225_map.bin, although some bytes differ when comparing with wlctl dumps.

Dumps from the OEM firmware:

> > wlctl revinfo vendorid 0x14e4 deviceid 0x4357 radiorev 0xb2056000 chipnum 0xa8d9 chiprev 0x1 chippackage 0xa corerev 0x17 boardid 0xa8d8 boardvendor 0x14e4 boardrev P200 driverrev 0x5647b00 ucoderev 0x2930000 bus 0x1 phytype 0x4 phyrev 0x6 anarev 0x0 > wlctl srdump srom[000]: 0x2801 0x0000 0x04da 0x14e4 0x0078 0xedbe 0x0000 0x2bc4 srom[008]: 0x2a64 0x2964 0x2c64 0x3ce7 0x46ff 0x47ff 0x0c00 0x0820 srom[016]: 0x0030 0x1002 0x9f28 0x5d44 0x8080 0x1d8f 0x0032 0x0100 srom[024]: 0xdf00 0x71f5 0x8400 0x0083 0x8500 0x2010 0x0001 0xffff srom[032]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[040]: 0xffff 0xffff 0x1008 0x0005 0xffff 0xffff 0xffff 0xffff srom[048]: 0x4357 0x8000 0x0002 0x0000 0x1f30 0x1800 0x0000 0x0000 srom[056]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[064]: 0x5372 0x1200 0x0200 0x0000 0x1000 0x0000 0x0000 0x0000 srom[072]: 0x0000 0x0000 0x0000 0x88ff 0xffff 0xffff 0x0303 0x0202 srom[080]: 0xffff 0x0033 0xffff 0xffff 0xffff 0xffff 0xffff 0x0325 srom[088]: 0xffff 0x7800 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[096]: 0x204e 0xfed6 0x172e 0xfaab 0xffff 0xffff 0xffff 0xffff srom[104]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[112]: 0x204e 0xfecc 0x1665 0xfaac 0xffff 0xffff 0xffff 0xffff srom[120]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[128]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[136]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[144]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[152]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[160]: 0x0000 0x5555 0x5555 0x0000 0x0000 0x0000 0x0000 0x0000 srom[168]: 0x0000 0x5555 0x7555 0x5555 0x7555 0x5555 0x7555 0x5555 srom[176]: 0x7555 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 srom[184]: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 srom[192]: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 srom[200]: 0x0000 0x0000 0x0000 0x0002 0x0000 0xffff 0xffff 0xffff srom[208]: 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff 0xffff srom[216]: 0xffff 0xffff 0xffff 0x0008 > wlctl nvram_dump sromrev=8 boardrev=0x1200 boardflags=0x200 boardflags2=0x1000 boardtype=0x4da boardnum=0 regrev=0 ledbh1=136 pa0b0=0xfed6 pa0b1=0x172e pa0b2=0xfaab pa0itssit=32 pa0maxpwr=78 opo=85 aa2g=3 aa5g=3 ag0=2 ag1=2 ag2=255 ag3=255 pa1b0=0xffff pa1b1=0xffff pa1b2=0xffff pa1lob0=0xffff pa1lob1=0xffff pa1lob2=0xffff pa1hib0=0xffff pa1hib1=0xffff pa1hib2=0xffff pa1itssit=255 pa1maxpwr=255 pa1lomaxpwr=255 pa1himaxpwr=255 bxa2g=3 rssisav2g=7 rssismc2g=15 rssismf2g=15 bxa5g=3 rssisav5g=7 rssismc5g=15 rssismf5g=15 tri2g=255 tri5g=255 tri5gl=255 tri5gh=255 rxpo2g=-1 rxpo5g=-1 txchain=3 rxchain=3 antswitch=0 tssipos2g=1 extpagain2g=2 pdetrange2g=4 triso2g=3 antswctl2g=0 tssipos5g=1 extpagain5g=3 pdetrange5g=31 triso5g=7 antswctl5g=31 ccode= macaddr=38:72:c0:99:54:7e tempthresh=120 tempoffset=0 rawtempsense=0x1ff measpower=0x7f tempsense_slope=0xff tempcorrx=0x3f tempsense_option=0x3 freqoffset_corr=0xf iqcal_swp_dis=0x1 hw_iqcal_en=0x1 elna2g=255 elna5g=255 phycal_tempdelta=255 temps_period=15 temps_hysteresis=15 measpower1=0x7f measpower2=0x7f cck2gpo=0 ofdm2gpo=1431655765 ofdm5gpo=0 ofdm5glpo=0 ofdm5ghpo=0 mcs2gpo0=21845 mcs2gpo1=30037 mcs2gpo2=21845 mcs2gpo3=30037 mcs2gpo4=21845 mcs2gpo5=30037 mcs2gpo6=21845 mcs2gpo7=30037 mcs5gpo0=0 mcs5gpo1=0 mcs5gpo2=0 mcs5gpo3=0 mcs5gpo4=0 mcs5gpo5=0 mcs5gpo6=0 mcs5gpo7=0 mcs5glpo0=0 mcs5glpo1=0 mcs5glpo2=0 mcs5glpo3=0 mcs5glpo4=0 mcs5glpo5=0 mcs5glpo6=0 mcs5glpo7=0 mcs5ghpo0=0 mcs5ghpo1=0 mcs5ghpo2=0 mcs5ghpo3=0 mcs5ghpo4=0 mcs5ghpo5=0 mcs5ghpo6=0 mcs5ghpo7=0 cddpo=0 stbcpo=0 bw40po=2 bwduppo=0 pcieingress_war=15 rxgainerr2ga0=63 rxgainerr2ga1=31 rxgainerr2ga2=31 rxgainerr5gla0=63 rxgainerr5gla1=31 rxgainerr5gla2=31 rxgainerr5gma0=63 rxgainerr5gma1=31 rxgainerr5gma2=31 rxgainerr5gha0=63 rxgainerr5gha1=31 rxgainerr5gha2=31 rxgainerr5gua0=63 rxgainerr5gua1=31 rxgainerr5gua2=31 noiselvl2ga0=31 noiselvl2ga1=31 noiselvl2ga2=31 noiselvl5gla0=31 noiselvl5gla1=31 noiselvl5gla2=31 noiselvl5gma0=31 noiselvl5gma1=31 noiselvl5gma2=31 noiselvl5gha0=31 noiselvl5gha1=31 noiselvl5gha2=31 noiselvl5gua0=31 noiselvl5gua1=31 noiselvl5gua2=31 maxp2ga0=78 itt2ga0=32 itt5ga0=255 pa2gw0a0=0xfed6 pa2gw1a0=0x172e pa2gw2a0=0xfaab maxp5ga0=255 maxp5gha0=255 maxp5gla0=255 pa5gw0a0=0xffff pa5gw1a0=0xffff pa5gw2a0=0xffff pa5glw0a0=0xffff pa5glw1a0=0xffff pa5glw2a0=0xffff pa5ghw0a0=0xffff pa5ghw1a0=0xffff pa5ghw2a0=0xffff maxp2ga1=78 itt2ga1=32 itt5ga1=255 pa2gw0a1=0xfecc pa2gw1a1=0x1665 pa2gw2a1=0xfaac maxp5ga1=255 maxp5gha1=255 maxp5gla1=255 pa5gw0a1=0xffff pa5gw1a1=0xffff pa5gw2a1=0xffff pa5glw0a1=0xffff pa5glw1a1=0xffff pa5glw2a1=0xffff pa5ghw0a1=0xffff pa5ghw1a1=0xffff pa5ghw2a1=0xffff maxp2ga2=255 itt2ga2=255 itt5ga2=255 pa2gw0a2=0xffff pa2gw1a2=0xffff pa2gw2a2=0xffff maxp5ga2=255 maxp5gha2=255 maxp5gla2=255 pa5gw0a2=0xffff pa5gw1a2=0xffff pa5gw2a2=0xffff pa5glw0a2=0xffff pa5glw1a2=0xffff pa5glw2a2=0xffff pa5ghw0a2=0xffff pa5ghw1a2=0xffff pa5ghw2a2=0xffff maxp2ga3=255 itt2ga3=255 itt5ga3=255 pa2gw0a3=0xffff pa2gw1a3=0xffff pa2gw2a3=0xffff maxp5ga3=255 maxp5gha3=255 maxp5gla3=255 pa5gw0a3=0xffff pa5gw1a3=0xffff pa5gw2a3=0xffff pa5glw0a3=0xffff pa5glw1a3=0xffff pa5glw2a3=0xffff pa5ghw0a3=0xffff pa5ghw1a3=0xffff pa5ghw2a3=0xffff devid=0x4357 >


JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
ar-5381u_board_serial.jpg

Photo of PCB with markings

GPIO

LEDs

Read: System configuration: Leds to configure the leds

Pin Event Active Soldered
2 ALARM (red) Low Yes
3 ADSL (green) Low Yes
4 Power (green) Low Yes
5 wps Low No
8 power (red) Low No
11 alarm (green) Low No

Buttons

→ hardware.button on howto use and configure the hardware button(s).

Pin Event Active Soldered
23 Reset Low Yes
24 Extra 1 Low No
31 Extra 2 Low No

Hardware mods

→ as a beginner, you really should inform yourself about soldering in general and then obtain some practical experience!

Pasive POE

Pairs
VDC 4, 5
GND 7, 8

Solder the cables as shown int the picture:

After the mod you're ready to use a 12V passive POE connected to the LAN1X. Warning! don't connect the router Power adapter and the POE at the same time. Only use this ethernet port for POE purposes.

The power management circuit uses two CAT7114 step-down switch mode converters: ar-5381u-pmc.jpg. There is no datasheet available. The equivalent IC is a MP1411 which supports a max voltage of 18V.

Bootlogs

OEM Bootlog

CFE version 1.0.37-106.5-9 for BCM96328 (32bit,SP,BE) Build Date: 2010-12-20 22:52:56 (tony@broadcom_eu) Copyright (C) 2000-2009 Broadcom Corporation. HS Serial flash device: name MX25L128, id 0xc218 size 16384KB Total Flash size: 16384K with 256 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-5) : 96328A-1241N Number of MAC Addresses (1-32) : 11 Base MAC Address : 11:22:33:44:55:66 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Serial Number : Default PSK key : xxxxxxxxxxxxxxxxx *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from latest image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80292f40 Decompression OK! Entry at 0x80292f40 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80292f40 Linux version 2.6.30 (lucien@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #3 Fri Oct 28 13:22:45 CST 2011 HS Serial flash device: name MX25L128, id 0xc218 size 16384KB 96328A-1241N prom init CPU revision is: 0002a075 (Broadcom4350) Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 8031cf10, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60384k/64512k available (2595k kernel code, 4108k reserved, 533k data, 124k init, 0k highmem) Calibrating delay loop... 319.48 BogoMIPS (lpj=159744) Mount-cache hash table entries: 512 --Kernel Config-- SMP=0 PREEMPT=0 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Oct 28 2011 13:07:23 net_namespace: 812 bytes NET: Registered protocol family 16 Total Flash size: 16384K with 4096 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Oct 28 2011 13:09:14 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 117 io scheduler noop registered (default) pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8010100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8009 is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX Total # RxBds=948 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Oct 28 2011 13:08:56 GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 124k freed init started: BusyBox v1.00 (2011.10.28-05:10+0000) multi-call binary BusyBox v1.00 (2011.10.28-05:10+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Oct 28 2011 13:07:54 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Oct 28 2011 13:07:54 bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6328B0 Ethernet Network Device v0.1 Oct 28 2011 13:08:52 ETH Init: Ch:0 - 180 tx BDs at 0xa395a000 ETH Init: Ch:1 - 180 tx BDs at 0xa3a25000 ETH Init: Ch:0 - 400 rx BDs at 0xa3a24000 ETH Init: Ch:1 - 100 rx BDs at 0xa3a2b800 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: 11:22:33:44:55:66 eth1: MAC Address: 11:22:33:44:55:66 eth2: MAC Address: 11:22:33:44:55:66 eth3: MAC Address: 11:22:33:44:55:66 BCM63XX_USB USB Device not present insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl: allocskbmode=1 wl:srom strapped wl:(srom strapped) probe/present=0 wl:srom not detected, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43225_map.bin wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.100.123.0.cpe4.10L02.2 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Broadcom 802.1Q VLAN Interface, v0.1 ===== Comtrend Release Version A731-410JAZ-C05_R01 ===== Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state BcmAdsl_Initialize=0xC00A9ED0, g_pFnNotifyCallback=0xC00D2C04 WLmngr Daemon is running optarg=0 shmId=0 wlevt is ready for new msg... pSdramPHY=0xA3FFFFF8, 0x0 0xFFFF0000 *** XfaceOffset: 0x21F90 => 0x21F90 *** *** PhySdramSize got adjusted: 0x8339C => 0x98D48 *** AdslCoreSharedMemInit: shareMemAvailable=422544 AdslCoreHwReset: pLocSbSta=82dc8000 bkupThreshold=1600 AdslCoreHwReset: AdslOemDataAddr = 0xA3F783D4 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa3975000 XTM Init: 16 rx BDs at 0xa2d8be80 Register interface ppp0 !! iptables v1.4.0: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. monitor task is initialized pid= 246 upnp:error:23.645:process_smd_connection:474:cannot handle msg type 0x10000250 echo 005d0140 > /proc/switch Comtrend polling daemon is running Switch MDK: num_switches = 1 Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf Switch MDK link poll thread: unit=0; phypbmp=0xf device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state There is no Predefined DevicePin in CFE WPS Device PIN = 00000000 Setting SSID: "Jazztel_xxxx" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state UPnP daemon is ready to run acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b01


OpenWrt

[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Sep 9 20:22:25 CEST 2012 [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0 [ 0.000000] CPU frequency is 320 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 32 GPIOs [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.5 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96328A-1241N [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802acea0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Memory: 61808k/65536k available (2262k kernel code, 3728k reserved, 415k data, 204k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.276000] registering PCI controller with io_map_base unset [ 0.288000] bio: create slab <bio-0> at 0 [ 0.292000] PCI host bridge to bus 0000:00 [ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff] [ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604 [ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280 [ 0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit] [ 0.304000] pci 0000:01:00.0: supports D1 D2 [ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff] [ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit] [ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff] [ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.324000] Switching to clocksource MIPS [ 0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x08 [ 0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606) [ 0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9 [ 0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9 [ 0.404000] bcma: bus0: SPROM offset 0x800 [ 0.444000] bcma: Reading SPROM failed. Trying fallback SPROM... [ 0.444000] bcm63xx_sprom_bcma: filled BCMA SPROM for chip id 0xa8d9 [ 0.448000] bcma: bus0: Using SPROM revision 8 provided by platform. [ 0.448000] bcma: bus0: Bus registered [ 0.452000] NET: Registered protocol family 2 [ 0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.468000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.472000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.480000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.488000] TCP reno registered [ 0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.504000] NET: Registered protocol family 1 [ 0.508000] PCI: CLS 0 bytes, default 16 [ 0.512000] audit: initializing netlink socket (disabled) [ 0.516000] type=2000 audit(0.516:1): initialized [ 0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540000] msgmni has been set to 120 [ 0.544000] io scheduler noop registered [ 0.548000] io scheduler deadline registered (default) [ 0.556000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart [ 0.564000] console [ttyS0] enabled, bootconsole disabled [ 0.580000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.592000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1241N [ 0.600000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.608000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00 [ 0.612000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000 [ 0.620000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000 [ 0.628000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000 [ 0.636000] bcm63xxpart: Spare partition is offset 340004 and length cafffc [ 0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0 [ 0.648000] Creating 5 MTD partitions on "spi0.0": [ 0.656000] 0x000000000000-0x000000010000 : "CFE" [ 0.660000] 0x000000010100-0x000000100000 : "kernel" [ 0.668000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.684000] 0x000000100000-0x000000ff0000 : "rootfs" [ 0.692000] mtd: partition "rootfs" set to be root filesystem [ 0.696000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=CB0000 [ 0.704000] 0x000000340000-0x000000ff0000 : "rootfs_data" [ 0.712000] 0x000000ff0000-0x000001000000 : "nvram" [ 0.720000] 0x000000010000-0x000000ff0000 : "linux" [ 0.764000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.772000] TCP cubic registered [ 0.776000] NET: Registered protocol family 17 [ 0.780000] 8021q: 802.1Q VLAN Support v1.8 [ 0.792000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.804000] Freeing unused kernel memory: 204k freed [ 3.148000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 3.384000] roboswitch: Probing device eth0: [ 3.388000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external [ 3.400000] No Robo switch in managed mode found, phy_id = 0xffffffff [ 3.404000] roboswitch: Probing device eth1: No such device [ 3.412000] roboswitch: Probing device eth2: No such device [ 3.416000] roboswitch: Probing device eth3: No such device [ 5.940000] Button Hotplug driver version 0.4.1 [ 12.632000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993 [ 12.640000] Backport based on wireless-testing.git master-2012-09-07 [ 12.648000] compat.git: wireless-testing.git [ 12.708000] cfg80211: Calling CRDA to update world regulatory domain [ 12.712000] cfg80211: World regulatory domain updated: [ 12.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.728000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.736000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.744000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.752000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.760000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.152000] NET: Registered protocol family 10 [ 13.596000] SCSI subsystem initialized [ 13.644000] There is already a switch registered on the device 'eth0' [ 13.652000] roboswitch: Probing device eth1: No such device [ 13.656000] roboswitch: Probing device eth2: No such device [ 13.664000] roboswitch: Probing device eth3: No such device [ 13.940000] usbcore: registered new interface driver usbfs [ 13.948000] usbcore: registered new interface driver hub [ 13.956000] usbcore: registered new device driver usb [ 15.188000] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 15.836000] PPP generic driver version 2.4.2 [ 16.268000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31 [ 16.616000] bcma: bus0: Switched to core: 0x812 [ 16.620000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.776000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 17.120000] NET: Registered protocol family 24 [ 17.456000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 17.568000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller [ 17.572000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1 [ 17.604000] bcm63xx_ehci bcm63xx_ehci.0: irq 50, io mem 0xb0002500 [ 17.620000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 17.628000] hub 1-0:1.0: USB hub found [ 17.632000] hub 1-0:1.0: 1 port detected [ 17.796000] nf_conntrack version 0.5.0 (968 buckets, 3872 max) [ 18.592000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 18.904000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 19.016000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller [ 19.020000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2 [ 19.028000] bcm63xx_ohci bcm63xx_ohci.0: irq 49, io mem 0xb0002600 [ 19.096000] hub 2-0:1.0: USB hub found [ 19.100000] hub 2-0:1.0: 1 port detected [ 19.288000] Initializing USB Mass Storage driver... [ 19.292000] usbcore: registered new interface driver usb-storage [ 19.300000] USB Mass Storage support registered. [ 19.464000] usbcore: registered new interface driver ums-alauda [ 19.492000] usbcore: registered new interface driver ums-cypress [ 19.524000] usbcore: registered new interface driver ums-datafab [ 19.552000] usbcore: registered new interface driver ums-freecom [ 19.584000] usbcore: registered new interface driver ums-isd200 [ 19.612000] usbcore: registered new interface driver ums-jumpshot [ 19.640000] usbcore: registered new interface driver ums-karma [ 19.672000] usbcore: registered new interface driver ums-sddr09 [ 19.700000] usbcore: registered new interface driver ums-sddr55 [ 19.732000] usbcore: registered new interface driver ums-usbat [ 24.320000] device eth0 entered promiscuous mode [ 24.324000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 24.336000] br-lan: port 1(eth0) entered forwarding state [ 24.340000] br-lan: port 1(eth0) entered forwarding state [ 26.344000] br-lan: port 1(eth0) entered forwarding state [ 42.920000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 42.928000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 42.932000] jffs2_build_filesystem(): erasing all blocks after the end marker...


Tags

How to add tags

, , , , , , , , ,
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1