Compex WPJ531

Install OpenWrt (generic explanation)

  1. Put OpenWrt firmware image file at
    ftp://192.168.1.10/openwrt-15.05-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
  2. Excute the following commands
    tftpboot 0x80500000 openwrt-15.05-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
    erase 0x9f030000 +$filesize
    erase 0x9f680000 +1
    cp.b $fileaddr 0x9f030000 $filesize
    boot
Architecture MIPS
Vendor Qualcomm-Atheros
Bootloader U-Boot
System-On-Chip QCA9531
Switch [none] Soc has two 100Mbps phys
CPU Speed 650 MHz
Flash size 8 MB (max 16 MB optional)
RAM 64 MB DDR2
Wireless on-board abgn radio, 1 miniPCIe slot; all Compex WLE series, including 802.11ac radio
Ethernet 2 × 100Mbps ports
PoE Integrated 48V 802.3af (alternative 24V PoE available)
Extras Serial Port 2, JTAG 3, Reset Button, Surge Arrestor, Watchdog Timer
USB With USB Extension (optional), can support 1 × miniPCIe-based USB 2.0 only interface (e.g. 3G modems), 2 × USB 2.0 ports
Serial yes

Serial pinout is VCC, RX, TX, GND (from top to bottom, as shown in the photo). Note: RX and TX here and in the image are relative to the host PC!

UART speed is 115200

USB is available on a header with GND, D+, D-, VCC (from left to right, as shown in the photo).

U-Boot 1.1.4 (Apr 10 2015 - 16:51:40) wpj531 - Honey Bee 2.0 DRAM: 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 141k for U-Boot at: 83fdc000 Reserving 192k for malloc() at: 83fac000 Reserving 44 Bytes for Board Info at: 83fabfd4 Reserving 36 Bytes for Global Data at: 83fabfb0 Reserving 128k for boot params() at: 83f8bfb0 Stack Pointer at: 83f8bf98 Now running in RAM - U-Boot at: 83fdc000 Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18 Flash found: mx25l 16MB Flash: 16 MB Using default environment eth_set_enetaddr(num=0, addr=04:f0:21:19:a8:4c) eth_set_enetaddr(num=0, addr=04:f0:21:19:a8:4c) In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->S27 PHY* S27 reg init : cfg1 0x800c0000 cfg2 0x7114 eth0: 04:f0:21:19:a8:4c athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 eth0 up Honey Bee ----> MAC 1 S27 PHY * S27 reg init ATHRS27: resetting s27 ATHRS27: s27 reset done : cfg1 0x800c0000 cfg2 0x7214 eth1: 04:f0:21:19:a8:4d athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :50 athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 eth1 up eth0, eth1 Setting 0x181162c0 to 0x60c1a100 Hit any key to stop autoboot: 0 ath> ath> ath> printenv bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),8256k(mib0),64k(ART) bootdelay=1 baudrate=115200 ipaddr=192.168.1.1 serverip=192.168.1.10 dir= lu=tftp 0x80060000 ${dir}tuboot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize lf=tftp 0x80060000 ${dir}wpj531${bc}-jffs2&&erase 0x9f050000 +0x630000&&cp.b $fileaddr 0x9f050000 $filesize lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize&&cp.b $fileaddr 0x9f680000 $filesize ethaddr=04:f0:21:19:a8:4c bootcmd=bootm 0x9f680000 || bootm 0x9f030000 stdin=serial stdout=serial stderr=serial ethact=eth0 Environment size: 694/65532 bytes


[ 0.000000] Linux version 3.3.8 (ttyaw@debian-x58) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #10 Thu Apr 9 11:09:13 SGT 2015 [ 0.000000] MyLoader: sysp=d01be1cb, boardp=17a97e1c, parts=733174db [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802dbf10, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=WPJ531 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1344k(kernel),64k(otp)ro,64k(nvram),64k(art)ro,7680k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61600k/65536k available (2151k kernel code, 3936k reserved, 393k data, 188k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] NET: Registered protocol family 16 [ 0.070000] gpiochip_add: registered GPIOs 0 to 23 on device: ath79 [ 0.080000] MIPS: machine is Compex WPJ531 [ 0.100000] ar724x-pci ar724x-pci.0: PCIe link is down [ 0.100000] registering PCI controller with io_map_base unset [ 0.110000] bio: create slab <bio-0> at 0 [ 0.120000] PCI host bridge to bus 0000:00 [ 0.120000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.130000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.130000] Switching to clocksource MIPS [ 0.140000] NET: Registered protocol family 2 [ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.150000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.160000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.160000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.170000] TCP reno registered [ 0.170000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.180000] NET: Registered protocol family 1 [ 0.190000] PCI: CLS 0 bytes, default 32 [ 0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.210000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.220000] msgmni has been set to 120 [ 0.220000] io scheduler noop registered [ 0.230000] io scheduler deadline registered (default) [ 0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.270000] console [ttyS0] enabled, bootconsole disabled [ 0.280000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.290000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.290000] 8 cmdlinepart partitions found on MTD device spi0.0 [ 0.300000] Creating 8 MTD partitions on "spi0.0": [ 0.300000] 0x000000000000-0x000000040000 : "u-boot" [ 0.310000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.320000] 0x000000050000-0x000000680000 : "rootfs" [ 0.330000] mtd: partition "rootfs" set to be root filesystem [ 0.330000] mtd: partition "rootfs_data" created automatically, ofs=5E0000, len=A0000 [ 0.340000] 0x0000005e0000-0x000000680000 : "rootfs_data" [ 0.350000] 0x000000680000-0x0000007d0000 : "kernel" [ 0.350000] 0x0000007d0000-0x0000007e0000 : "otp" [ 0.360000] 0x0000007e0000-0x0000007f0000 : "nvram" [ 0.370000] 0x0000007f0000-0x000000800000 : "art" [ 0.370000] 0x000000050000-0x0000007d0000 : "firmware" [ 0.400000] ag71xx_mdio: probed [ 0.410000] TCP cubic registered [ 0.410000] NET: Registered protocol family 17 [ 0.420000] 8021q: 802.1Q VLAN Support v1.8 [ 0.430000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.440000] Freeing unused kernel memory: 188k freed [ 2.310000] Registered led device: wpj531:red:sig1 [ 2.310000] Registered led device: wpj531:yellow:sig2 [ 2.310000] Registered led device: wpj531:green:sig3 [ 2.310000] Registered led device: wpj531:green:sig4 [ 2.310000] Registered led device: wpj531:buzzer [ 8.280000] qca955x_GMAC: Length per segment 1536 [ 8.280000] 953x_GMAC: qca953x_gmac_attach [ 8.290000] Link Int Enabled [ 8.290000] qca953x_set_gmac_caps CHECK DMA STATUS [ 8.300000] mac:0 Registering S27.... [ 8.300000] qca955x_GMAC: RX TASKLET - Pkts per Intr:18 [ 8.300000] qca955x_GMAC: Mac address for unit 0: 04:f0:21:1b:0c:2c [ 8.310000] qca955x_GMAC: Max segments per packet : 1 [ 8.320000] qca955x_GMAC: Max tx descriptor count : 512 [ 8.320000] qca955x_GMAC: Max rx descriptor count : 128 [ 8.330000] qca955x_GMAC: Mac capability flags : 2581 [ 8.330000] 953x_GMAC: qca953x_gmac_attach [ 8.340000] Link Int Enabled [ 8.340000] GPIO LED SETTINGS ....done [ 8.350000] qca953x_set_gmac_caps CHECK DMA STATUS [ 8.350000] mac:1 Registering S27.... [ 8.350000] qca955x_GMAC: RX TASKLET - Pkts per Intr:18 [ 8.360000] qca955x_GMAC: Mac address for unit 1: 04:f0:21:1b:0c:2d [ 8.370000] qca955x_GMAC: Max segments per packet : 1 [ 8.370000] qca955x_GMAC: Max tx descriptor count : 512 [ 8.380000] qca955x_GMAC: Max rx descriptor count : 128 [ 8.380000] qca955x_GMAC: Mac capability flags : 2D81 [ 9.190000] NET: Registered protocol family 10 [ 9.560000] usbcore: registered new interface driver usbfs [ 9.560000] usbcore: registered new interface driver hub [ 9.570000] usbcore: registered new device driver usb [ 9.660000] NET: Registered protocol family 15 [ 9.700000] Initializing XFRM netlink socket [ 9.730000] PPP generic driver version 2.4.2 [ 9.760000] tun: Universal TUN/TAP device driver, 1.6 [ 9.770000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 9.820000] PPP MPPE Compression module registered [ 10.110000] L2TP core driver, V2.0 [ 10.130000] L2TP netlink interface [ 10.150000] L2TP ethernet pseudowire support (L2TPv3) [ 10.170000] L2TP IP encapsulation support (L2TPv3) [ 10.200000] GRE over IPv4 demultiplexor driver [ 10.220000] GRE over IPv4 tunneling driver [ 10.340000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.610000] NET: Registered protocol family 24 [ 10.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.710000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller [ 10.720000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 10.750000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 10.770000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 10.770000] hub 1-0:1.0: USB hub found [ 10.780000] hub 1-0:1.0: 1 port detected [ 10.780000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller [ 10.790000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 10.830000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 10.850000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 10.850000] hub 2-0:1.0: USB hub found [ 10.860000] hub 2-0:1.0: 1 port detected [ 10.950000] nf_conntrack version 0.5.0 (965 buckets, 3860 max) [ 11.350000] PPPoL2TP kernel driver, V2.0 [ 11.360000] PPTP driver version 0.8.5 [ 11.820000] xt_time: kernel timezone is -0000 [ 12.420000] adf: module license 'Proprietary' taints kernel. [ 12.430000] Disabling lock debugging due to kernel taint [ 12.780000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 12.880000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 12.910000] ath_spectral: Version 2.0.0 [ 12.910000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 12.920000] SPECTRAL module built on Apr 9 2015 10:59:07 [ 12.950000] ath_dfs: Version 2.0.0 [ 12.950000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 13.150000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 14.480000] ath_ahb: 10.2-00082-4 (Atheros/multi-bss) [ 14.490000] __ath_attach: Set global_scn[0] [ 14.490000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead *** [ 14.500000] ACBKMinfree = 48 [ 14.500000] ACBEMinfree = 32 [ 14.510000] ACVIMinfree = 16 [ 14.510000] ACVOMinfree = 0 [ 14.510000] CABMinfree = 48 [ 14.520000] UAPSDMinfree = 0 [ 14.520000] ATH_TXBUF=512 [ 14.530000] Enterprise mode: 0x03fc0000 [ 14.530000] Restoring Cal data from Flash [ 14.540000] SPECTRAL : get_capability not registered [ 14.550000] HAL_CAP_PHYDIAG : Capable [ 14.550000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 14.560000] SPECTRAL : get_capability not registered [ 14.560000] HAL_CAP_RADAR : Capable [ 14.570000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 14.570000] (spectral_attach : 236) [ 14.580000] SPECTRAL : get_capability not registered [ 14.580000] HAL_CAP_SPECTRAL_SCAN : Capable [ 14.590000] SPECTRAL : get_tsf64 not registered [ 14.590000] spectral_init_netlink 52 NULL SKB [ 14.600000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 14.600000] SPECTRAL :----- module attached [ 14.610000] Green-AP : Green-AP : Attached [ 14.610000] [ 14.620000] ath_get_caps[6174] rx chainmask mismatch actual 3 sc_chainmak 0 [ 14.620000] ath_get_caps[6149] tx chainmask mismatch actual 3 sc_chainmak 0 [ 14.640000] ath_attach_dfs[12587] dfsdomain 0 [ 14.650000] SPECTRAL : module already attached [ 14.660000] ath_tx_paprd_init sc 833e8000 PAPRD disabled in HAL [ 14.670000] wifi0: Atheros 953X: mem=0xb8100000, irq=47 [ 14.670000] ath_pci: 10.2-00082-4 (Atheros/multi-bss) [ 14.780000] batman_adv: B.A.T.M.A.N. advanced 2013.2.0 (compatibility version 14) loaded [ 20.640000] athr_gmac_ring_alloc Allocated 8192 at 0x821c6000 [ 20.650000] athr_gmac_ring_alloc Allocated 2048 at 0x830a3800 [ 20.950000] HONEYBEE ----> S27 PHY MDIO [ 20.960000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 20.970000] Setting PHY... [ 23.990000] 953x_GMAC: Enet Unit:0 PHY:4 is UP eth0 MII 100Mbps full duplex [ 23.990000] 953x_GMAC: done cfg2 0x7115 ifctl 0x10000 miictrl [ 23.990000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 24.020000] device eth0 entered promiscuous mode [ 24.020000] br-lan: port 1(eth0) entered forwarding state [ 24.030000] br-lan: port 1(eth0) entered forwarding state [ 24.050000] athr_gmac_ring_alloc Allocated 8192 at 0x82290000 [ 24.060000] athr_gmac_ring_alloc Allocated 2048 at 0x8227f000 [ 24.360000] HONEYBEE ----> S27 PHY MDIO [ 24.370000] ATHRS27: resetting s27 [ 24.470000] ATHRS27: s27 reset done [ 24.480000] Setting Drop CRC Errors, Pause Frames and Length Error frames [ 24.490000] Setting PHY... [ 25.540000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 25.540000] device eth1 entered promiscuous mode [ 26.030000] br-lan: port 1(eth0) entered forwarding state [ 26.810000] DCS for CW interference mitigation: 0 [ 26.810000] DCS for WLAN interference mitigation: 0 [ 27.090000] wlan_vap_create : enter. devhandle=0x82480380, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 27.100000] wlan_vap_create : exit. devhandle=0x82480380, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 27.110000] VAP device ath0 created [ 27.420000] Set freq vap stop send + 82314000 [ 27.420000] Set freq vap stop send -82314000 [ 27.460000] Set wait done --82314000 [ 27.560000] [ 27.560000] DES SSID SET=MimoSeries [ 30.090000] device ath0 entered promiscuous mode [ 30.100000] br-lan: port 3(ath0) entered forwarding state [ 30.100000] br-lan: port 3(ath0) entered forwarding state [ 32.100000] br-lan: port 3(ath0) entered forwarding state [ 48.860000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 48.890000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 48.890000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 52.100000] JFFS2 notice: (2080) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.


[ 0.000000] Linux version 3.18.16 (openwrt@gb-15) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46134) ) #1 Mon Jun 29 09:45:50 UTC 2015 [ 0.000000] MyLoader: sysp=d01be1cb, boardp=17a97e1c, parts=733174db [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 803882b0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=WPJ531 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60748K/65536K available (2647K kernel code, 132K rwdata, 548K rodata, 248K init, 194K bss, 4788K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] NET: Registered protocol family 16 [ 0.080000] MIPS: machine is Compex WPJ531 [ 0.090000] ar71xx: using random MAC address for eth0 [ 0.310000] ar71xx: using random MAC address for eth1 [ 0.530000] Switched to clocksource MIPS [ 0.540000] NET: Registered protocol family 2 [ 0.540000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.550000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.550000] TCP: reno registered [ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.570000] NET: Registered protocol family 1 [ 0.570000] PCI: CLS 0 bytes, default 32 [ 0.580000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.620000] msgmni has been set to 118 [ 0.630000] io scheduler noop registered [ 0.630000] io scheduler deadline registered (default) [ 0.640000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.650000] console [ttyS0] disabled [ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.680000] console [ttyS0] enabled [ 0.680000] bootconsole [early0] disabled [ 0.700000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.700000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.710000] 3 cmdlinepart partitions found on MTD device spi0.0 [ 0.710000] Creating 3 MTD partitions on "spi0.0": [ 0.720000] 0x000000000000-0x000000030000 : "u-boot" [ 0.720000] 0x000000030000-0x000000ff0000 : "firmware" [ 0.770000] 2 uimage-fw partitions found on MTD device firmware [ 0.770000] 0x000000030000-0x000000160000 : "kernel" [ 0.780000] 0x000000160000-0x000000ff0000 : "rootfs" [ 0.780000] mtd: device 3 (rootfs) set to be root filesystem [ 0.790000] 1 squashfs-split partitions found on MTD device rootfs [ 0.800000] 0x000000360000-0x000000ff0000 : "rootfs_data" [ 0.800000] 0x000000ff0000-0x000001000000 : "art" [ 0.830000] libphy: ag71xx_mdio: probed [ 1.430000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 1.440000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.030000] ag71xx-mdio.1: Found an AR934X built-in switch [ 2.070000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.080000] TCP: cubic registered [ 2.080000] NET: Registered protocol family 17 [ 2.090000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.100000] Bridge firewalling registered [ 2.100000] 8021q: 802.1Q VLAN Support v1.8 [ 2.120000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.130000] Freeing unused kernel memory: 248K (803a2000 - 803e0000) [ 3.130000] init: Console is alive [ 3.140000] init: - watchdog - [ 4.330000] usbcore: registered new interface driver usbfs [ 4.340000] usbcore: registered new interface driver hub [ 4.340000] usbcore: registered new device driver usb [ 4.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.360000] ehci-platform: EHCI generic platform driver [ 4.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.380000] ohci-platform: OHCI generic platform driver [ 5.140000] init: - preinit - [ 5.690000] random: procd urandom read with 8 bits of entropy available [ 8.520000] eth0: link up (100Mbps/Full duplex) [ 8.820000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 8.870000] eth0: link down [ 8.880000] procd: - early - [ 8.890000] procd: - watchdog - [ 9.570000] procd: - ubus - [ 10.580000] procd: - init - [ 11.410000] NET: Registered protocol family 10 [ 11.420000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.440000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 11.450000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 11.460000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.480000] nf_conntrack version 0.5.0 (953 buckets, 3812 max) [ 11.530000] xt_time: kernel timezone is -0000 [ 11.570000] cfg80211: Calling CRDA to update world regulatory domain [ 11.570000] cfg80211: World regulatory domain updated: [ 11.580000] cfg80211: DFS Master region: unset [ 11.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.600000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.610000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.620000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.630000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 11.640000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.650000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.650000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.750000] PPP generic driver version 2.4.2 [ 11.760000] NET: Registered protocol family 24 [ 11.820000] ath: EEPROM regdomain: 0x0 [ 11.820000] ath: EEPROM indicates default country code should be used [ 11.820000] ath: doing EEPROM country->regdmn map search [ 11.820000] ath: country maps to regdmn code: 0x3a [ 11.820000] ath: Country alpha2 being used: US [ 11.820000] ath: Regpair used: 0x3a [ 11.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 11.840000] ieee80211 phy0: Atheros AR9531 Rev:0 mem=0xb8100000, irq=2 [ 11.850000] cfg80211: Calling CRDA for country: US [ 11.850000] cfg80211: Regulatory domain changed to country: US [ 11.860000] cfg80211: DFS Master region: FCC [ 11.860000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.870000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 11.880000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A) [ 11.890000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 11.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 11.910000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 18.660000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 18.690000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 18.690000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 21.910000] device eth0 entered promiscuous mode [ 21.950000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 22.000000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 45.740000] eth0: link up (100Mbps/Full duplex) [ 45.740000] br-lan: port 1(eth0) entered forwarding state [ 45.750000] br-lan: port 1(eth0) entered forwarding state [ 45.770000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 47.750000] br-lan: port 1(eth0) entered forwarding state [ 57.740000] eth0: link down [ 57.740000] br-lan: port 1(eth0) entered disabled state [ 58.640000] eth1: link up (1000Mbps/Full duplex) [ 58.640000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 66.770000] random: nonblocking pool is initialized [ 79.800000] done. [ 79.800000] jffs2: notice: (912) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 569.950000] eth1: link down [ 574.740000] eth0: link up (100Mbps/Full duplex) [ 574.740000] br-lan: port 1(eth0) entered forwarding state [ 574.750000] br-lan: port 1(eth0) entered forwarding state [ 576.750000] br-lan: port 1(eth0) entered forwarding state [ 578.740000] eth0: link down [ 578.740000] br-lan: port 1(eth0) entered disabled state [ 581.950000] eth1: link up (1000Mbps/Full duplex)

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1