Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:compex:wpe72 [2016/02/24 09:51] – [Upgrading OpenWRT (on Compex Myloader)] danghtoh:compex:wpe72 [2018/05/11 09:51] – Datatables added, cleanup tmomas
Line 1: Line 1:
 +====== Compex WPE72 ======
  
 +The device is supported in OpenWrt since Kamikaze 8.09.
 +
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,c,c,c,c,c,c
 +filter  : Model=WPE72
 +----
 +
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,c
 +filter  : Model=WPE72
 +----
 +
 +
 +===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : l,c,c
 +filter  : Model=WPE72
 +----
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
 +
 +==== Restore mode ====
 +
 +If you want to upload firmware to router by tftp, you will have to turn your device to this mode. The procedure is following:
 +
 +  - Turn off the device.
 +  - Press and hold the reset button.
 +  - Plug the device (still hold the button).
 +  - Wait until the Diagnostic LED (second from the left) starts flashing quickly. (This will happen almost immediately.)
 +  - Now release the reset button. Your router is in Restore mode.
 +
 +==== TFTP installation notes ====
 +
 +Set your ethernet interface into static mode (IP address 192.168.168.10, netmask 255.255.255.0, default gateway 192.168.168.1), put your router into **[[toh:compex:wpe72#restore_mode|Restore mode]]** and upload the firmware by TFTP using the following commands (replace XXXXXX with wpe72):
 +
 +<code>
 +$ tftp 192.168.168.1
 +tftp> binary
 +tftp> trace
 +tftp> put openwrt-ar71xx-wpe72.bin
 +</code>
 +
 +Diagnostic LED will now stop blinking for a while; if the flashing procedure is successfully done, it will start blinking slowly. Now reboot your router manually (turn off - turn on) and OpenWrt will boot. 
 +
 +===== Upgrading OpenWrt (on Compex Myloader) =====
 +
 +  - Getting source codes<code bash>
 +$ svn co -r 12448 https://snv.openwrt.org/openwrt/trunk</code>
 +  - Apply patches from the files mod-wpe72.tgz<code bash>
 +$ tar -zxvf mod-wpe72.tgz
 +$ cp -a mod-wpe72/* trunk/</code>
 +  - Compile<code bash>
 +$ cd trunk
 +$ cp wpe72.config .config
 +$ make</code>
 +
 +OpenWrt Firmware will be in //bin/openwrt-ar72xx-wpe72.bin//
 +
 +=== Uploading the OpenWrt firmware to WPE72 running MyLoader v2.54.0717 ===
 +
 +a. Via Compex Firmware
 +  * Put the AP in Firmware Upgrade mode and upload the file.
 +  * This file is for WPE72 with 4MB or 8MB NOR flash.
 +b. Via TFTP
 +  * Go to the firmware upgrade mode (By pressing and hold the Reset button and plug-in the power adapter).
 +  * Upload the OpenWrt image to the device (//$// **tftp -i 192.168.168.1 put openwrt-ar71xx-wpe72.bin**)
 +
 +===== Hardware info =====
 +^ Architecture     | MIPS                                                       |
 +^ Vendor           | Atheros                                                    |
 +^ Bootloader       | CFE                                                        |
 +^ System-On-Chip   | AR7240                                                     |
 +^ CPU Speed        | 400 Mhz                                                    |
 +^ Flash size       | 4 MB (up to 16 MB)                                         |
 +^ RAM              | 32 MB (max 64 MB) DDR SDRAM                                |
 +^ Wireless         | 1 × 9.2mm MiniPCI slot, support all Compex MiniPCI cards   |
 +^ Ethernet         | 2 × 10/100 Base-TX Ethernet Port (with Auto MDI/MDIX)      |
 +^ USB              | no                                                         |
 +^ Serial           | yes                                                        |
 +^ JTAG             | yes                                                        |
 +
 +===== Wireless =====
 +
 +Both madwifi and ath9k work well with all Compex MiniPCI cards. You will need some wireless authenticator and/or supplicant (wpad-mini/wpad/wpa-supplicant/hostpad/hostapd-mini).
 +
 +:!: Madwifi doesn't support MAC changes through UCI on this architecture. If you want to change of wireless MAC, see [[http://madwifi-project.org/wiki/UserDocs/ChangeMacAddress|this]]. 
 +
 +===== Useful sources =====
 +
 +This page has been assembled from a number of different pages from the old wiki and the current wiki. Refer to them for more (possibly outdated) information.
 +
 +  *<del>[[http://www.compex.com.sg/forum/|Compex forum]]</del> \\
 +  *<del>[[http://cpx.px.cz/|Another Compex forum (CZ/ENG)]]</del>
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>AR7240 4flash 32ram}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1