COMFAST CF-E560AC

COMFAST CF-E560AC is an ap143 based in-wall access point.

Generic Router

The stock firmware is based on OpenWrt, you can simply upload a squashfs-sysupgrade image through the web interface.

failsafe_and_factory_reset

This device automatically attempts to TFTP from 192.168.1.10:/firmware_auto.bin on every boot and will flash the firmware partition with a squashfs-sysupgrade format image from that address.

Architecture ath79
Vendor COMFAST
Bootloader U-Boot 1.1.4
System-On-Chip Qualcomm QCA9531 (HoneyBee) - MIPS 24Kc V7.4
CPU/Speed 650 MHz
Flash-Chip Winbond 25Q128JVSO
Flash size 16 MiB
RAM 128 MiB
Wireless 2.4g QCA9531 801.11 b/g/n
Wireless 5.0g QCA9886 801.11 a/n/ac
Ethernet 5x 10/100 ethernet, WAN port supports PoE 48v
USB 1x 2.0
Serial Yes

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

Serial connection is provided by 2.54mm headers clearly labeled on the main board.

Serial connection parameters
for COMFAST E560AC
115200, 8N1

There is no discernible JTAG header on the board.

U-Boot 1.1.4-g9e952007-dirty (Dec 20 2015 - 08:47:17)

ap143 - Honey Bee 2.0

DRAM: 128 MB Flash: 16 MB

eth0 link down FAIL eth1 link down FAIL Using eth0 device Tx Timed out ping failed; host 192.168.1.10 is not alive Unknown command 'ERROR!' - try 'help' Hit any key to stop autoboot: 0 ## Booting image at 9f020000 ...

 Image Name:   MIPS OpenWrt Linux-3.10.44
 Created:      2017-12-16   6:02:44 UTC
 Image Type:   MIPS Linux Kernel Image (lzma compressed)
 Data Size:    1124064 Bytes =  1.1 MB
 Load Address: 80060000
 Entry Point:  80060000
 Verifying Checksum at 0x9f020040 ...OK
 Uncompressing Kernel Image ... OK

No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 134217728

Starting kernel ...

[ 0.000000] Linux version 3.10.44 (root@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unk nown) ) #1 Sat Dec 16 14:01:59 CST 2017 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 ver 2 rev 0 [ 0.000000] Clocks: CPU:650.000MHz, DDR:391.870MHz, AHB:216.666MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=COMFAST-CF-E560AC console=ttyS0,115200 mtdparts=spi0.0:64k(u-b oot)ro,64k(art)ro,1536k(kernel),14592k(rootfs),64k(configs),64k(nvram)ro,16128k@0x20000(firmware) rootfst ype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125796k/131072k available (2425k kernel code, 5276k reserved, 689k data, 276k init , 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.050000] Mount-cache hash table entries: 512 [ 0.060000] NET: Registered protocol family 16 [ 0.070000] MIPS: machine is COMFAST CF-E560AC [ 0.510000] registering PCI controller with io_map_base unset [ 0.530000] bio: create slab <bio-0> at 0 [ 0.540000] PCI host bridge to bus 0000:00 [ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.560000] pci 0000:00:00.0: invalid calibration data [ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.570000] Switching to clocksource MIPS [ 0.580000] NET: Registered protocol family 2 [ 0.580000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.590000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.600000] TCP: reno registered [ 0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] NET: Registered protocol family 1 [ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.650000] msgmni has been set to 245 [ 0.660000] io scheduler noop registered [ 0.660000] io scheduler deadline registered (default) [ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.700000] console [ttyS0] enabled, bootconsole disabled [ 0.700000] console [ttyS0] enabled, bootconsole disabled [ 0.710000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.720000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.730000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.730000] 7 cmdlinepart partitions found on MTD device spi0.0 [ 0.740000] Creating 7 MTD partitions on “spi0.0”: [ 0.740000] 0x000000000000-0x000000010000 : “u-boot” [ 0.750000] 0x000000010000-0x000000020000 : “art” [ 0.760000] 0x000000020000-0x0000001a0000 : “kernel” [ 0.770000] 0x0000001a0000-0x000000fe0000 : “rootfs” [ 0.770000] mtd: device 3 (rootfs) set to be root filesystem [ 0.780000] 1 squashfs-split partitions found on MTD device rootfs [ 0.790000] 0x0000007c0000-0x000000fe0000 : “rootfs_data” [ 0.790000] 0x000000fe0000-0x000000ff0000 : “configs” [ 0.800000] 0x000000ff0000-0x000001000000 : “nvram” [ 0.810000] 0x000000020000-0x000000fe0000 : “firmware” [ 0.840000] libphy: ag71xx_mdio: probed [ 0.840000] eth0: Atheros AG71xx at 0xba000000, irq 5 [ 1.400000] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.440000] eth1: Atheros AG71xx at 0xb9000000, irq 4 [ 2.000000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.010000] TCP: cubic registered [ 2.010000] NET: Registered protocol family 17 [ 2.020000] Bridge firewalling registered [ 2.020000] 8021q: 802.1Q VLAN Support v1.8 [ 2.030000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.040000] Freeing unused kernel memory: 276K (8036b000 - 803b0000) [ 3.010000] init: Console is alive [ 3.010000] init: - watchdog - [ 5.010000] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.260000] jffs2: notice: (378) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found. [ 8.280000] mount_root: switching to jffs2 overlay [ 8.340000] procd: - early - [ 8.340000] procd: - watchdog - [ 8.960000] procd: - ubus - [ 9.990000] procd: - init - Please press Enter to activate this console. [ 11.840000] natsemi dp8381x driver, version 2.1, Sept 11, 2006 [ 11.840000] originally by Donald Becker becker@scyld.com [ 11.840000] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder [ 11.880000] gre: GRE over IPv4 demultiplexor driver [ 11.890000] ip_gre: GRE over IPv4 tunneling driver [ 11.910000] i2c /dev entries driver [ 11.910000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 11.920000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 12.150000] PCI: Enabling device 0000:00:00.0 (0000 → 0002) [ 12.150000] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 13.080000] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 [ 13.090000] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1 [ 13.120000] ath10k_pci 0000:00:00.0: firmware ver 10.4-3.5.1-00014 api 5 features no-p2p,mfp,peer-flow -ctrl,allows-mesh-bcast crc32 983b7b7a [ 13.420000] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:0 crc32 9310e54f [ 15.220000] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 [ 15.370000] u32 classifier [ 15.370000] input device check on [ 15.370000] Actions configured [ 15.390000] Mirror/redirect action on [ 15.420000] nf_conntrack version 0.5.0 (1969 buckets, 7876 max) [ 15.500000] Ebtables v2.0 registered [ 15.510000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.570000] Netfilter messages via NETLINK v0.30. [ 15.630000] xt_time: kernel timezone is -0000 [ 15.650000] ctnetlink v0.93: registering with nfnetlink. [ 15.670000] PPP generic driver version 2.4.2 [ 15.680000] PPP MPPE Compression module registered [ 15.690000] NET: Registered protocol family 24 [ 15.740000] ieee80211 phy1: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 [ 25.840000] device eth0 entered promiscuous mode [ 25.870000] device eth1 entered promiscuous mode [ 25.880000] br-lan: port 2(eth1) entered forwarding state [ 25.890000] br-lan: port 2(eth1) entered forwarding state [ 26.840000] br-lan: port 2(eth1) entered disabled state [ 30.210000] device wlan8 entered promiscuous mode [ 33.400000] device wlan0 entered promiscuous mode [ 37.500000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 39.240000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 40.660000] br-lan: port 3(wlan8) entered forwarding state [ 40.660000] br-lan: port 3(wlan8) entered forwarding state [ 41.430000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 42.220000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 42.660000] br-lan: port 3(wlan8) entered forwarding state


[ 0.000000] Linux version 4.19.98 (gus@uki) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12127-34e0065feb)) #0 Mon Feb 3 04:12:18 2020 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is COMFAST CF-E560AC [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 122428K/131072K available (4285K kernel code, 178K rwdata, 1012K rodata, 1236K init, 206K bss, 8644K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 650.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008271] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.074882] pid_max: default: 32768 minimum: 301 [ 0.080020] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.086996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100146] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.110599] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.117219] pinctrl core: initialized pinctrl subsystem [ 0.124008] NET: Registered protocol family 16 [ 0.137232] PCI host bridge /ahb/pcie-controller@180c0000 ranges: [ 0.143759] MEM 0x0000000010000000..0x0000000013ffffff [ 0.149257] IO 0x0000000000000000..0x0000000000000000 [ 0.182662] PCI host bridge to bus 0000:00 [ 0.187096] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.194337] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.200214] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.207366] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.215761] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000 [ 0.215830] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.215964] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.217117] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.217153] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.229639] clocksource: Switched to clocksource MIPS [ 0.236583] NET: Registered protocol family 2 [ 0.242239] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.250482] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.257843] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.264586] TCP: Hash tables configured (established 1024 bind 1024) [ 0.271487] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.277669] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.284837] NET: Registered protocol family 1 [ 0.289491] PCI: CLS 0 bytes, default 32 [ 0.294102] Crashlog allocated RAM at address 0x3f00000 [ 0.301623] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.316685] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.322911] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.350618] io scheduler noop registered [ 0.354760] io scheduler deadline registered (default) [ 0.361344] ar7200-usb-phy 18030000.usb-phy: phy reset is missing [ 0.370141] pinctrl-single 1804002c.pinmux: 576 pins, size 72 [ 0.377471] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.385158] console [ttyS0] disabled [ 0.388967] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.398151] console [ttyS0] enabled [ 0.405718] bootconsole [early0] disabled [ 0.433144] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.438083] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.444692] Creating 5 MTD partitions on “spi0.0”: [ 0.449691] 0x000000000000-0x000000010000 : “u-boot” [ 0.455915] 0x000000010000-0x000000020000 : “art” [ 0.461953] 0x000000020000-0x000000fe0000 : “firmware” [ 0.471335] 2 uimage-fw partitions found on MTD device firmware [ 0.477466] Creating 2 MTD partitions on “firmware”: [ 0.482683] 0x000000000000-0x0000001c0000 : “kernel” [ 0.488805] 0x0000001c0000-0x000000fc0000 : “rootfs” [ 0.494953] mtd: device 4 (rootfs) set to be root filesystem [ 0.502929] 1 squashfs-split partitions found on MTD device rootfs [ 0.509347] 0x000000400000-0x000000fc0000 : “rootfs_data” [ 0.516075] 0x000000fe0000-0x000000ff0000 : “configs” [ 0.522382] 0x000000ff0000-0x000001000000 : “nvram” [ 0.529935] libphy: Fixed MDIO Bus: probed [ 0.890755] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.570110] libphy: ag71xx_mdio: probed [ 1.575675] libphy: ar8xxx-mdio: probed [ 1.589407] switch0: Atheros AR8229 rev. 1 switch registered on mdio-bus.0 [ 1.641645] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.651784] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 1.658527] ath79-wdt 18060008.wdt: unable to register misc device, err=-16 [ 1.665869] ath79-wdt: probe of 18060008.wdt failed with error -16 [ 1.675133] NET: Registered protocol family 10 [ 1.687011] Segment Routing with IPv6 [ 1.691020] NET: Registered protocol family 17 [ 1.695715] 8021q: 802.1Q VLAN Support v1.8 [ 2.041793] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd042, driver=Generic PHY] [ 2.052842] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 2.070065] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.087545] Freeing unused kernel memory: 1236K [ 2.092277] This architecture does not have kernel memory protection. [ 2.098926] Run /sbin/init as init process [ 2.519658] random: fast init done [ 3.244124] init: Console is alive [ 3.247998] init: - watchdog - [ 4.786425] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.975764] usbcore: registered new interface driver usbfs [ 4.981665] usbcore: registered new interface driver hub [ 4.987282] usbcore: registered new device driver usb [ 5.001942] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.020681] SCSI subsystem initialized [ 5.031805] ehci-platform: EHCI generic platform driver [ 5.037566] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.043551] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.051826] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 5.079672] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.087184] hub 1-0:1.0: USB hub found [ 5.091762] hub 1-0:1.0: 1 port detected [ 5.101995] usbcore: registered new interface driver usb-storage [ 5.111624] usbcore: registered new interface driver uas [ 5.117988] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.136188] init: - preinit - [ 6.125504] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 6.401845] random: procd: uninitialized urandom read (4 bytes read) [ 6.412732] usb-storage 1-1:1.0: USB Mass Storage device detected [ 6.430440] scsi host0: usb-storage 1-1:1.0 [ 6.622916] random: jshn: uninitialized urandom read (4 bytes read) [ 6.727652] random: jshn: uninitialized urandom read (4 bytes read) [ 7.484330] scsi 0:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 4 [ 7.716687] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.722980] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 8.608792] sd 0:0:0:0: [sda] 249737216 512-byte logical blocks: (128 GB/119 GiB) [ 8.617266] sd 0:0:0:0: [sda] Write Protect is off [ 8.622294] sd 0:0:0:0: [sda] Mode Sense: 2f 00 00 00 [ 8.623015] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.640135] sda: sda1 sda2 [ 8.647645] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 8.750892] eth0: link up (1000Mbps/Full duplex) [ 8.757937] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.765003] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 12.050771] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 12.058293] jffs2_build_filesystem(): unlocking the mtd device... [ 12.058323] done. [ 12.066721] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 53.476347] done. [ 53.486149] jffs2: notice: (536) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 53.503955] mount_root: overlay filesystem has not been fully initialized yet [ 53.525212] mount_root: switching to jffs2 overlay [ 53.566142] overlayfs: upper fs does not support tmpfile. [ 54.066151] urandom-seed: Seed file not found (/etc/urandom.seed) [ 54.184498] eth0: link down [ 54.213333] procd: - early - [ 54.216460] procd: - watchdog - [ 54.865870] procd: - watchdog - [ 54.869596] procd: - ubus - [ 54.960091] urandom_read: 5 callbacks suppressed [ 54.960101] random: ubusd: uninitialized urandom read (4 bytes read) [ 54.972263] random: ubusd: uninitialized urandom read (4 bytes read) [ 54.980535] procd: - init - [ 55.837684] kmodloader: loading kernel modules from /etc/modules.d/* [ 55.891270] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 55.899102] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 55.958297] usbcore: registered new interface driver ums-alauda [ 55.981339] usbcore: registered new interface driver ums-cypress [ 56.001513] usbcore: registered new interface driver ums-datafab [ 56.010746] usbcore: registered new interface driver ums-freecom [ 56.031517] usbcore: registered new interface driver ums-isd200 [ 56.051482] usbcore: registered new interface driver ums-jumpshot [ 56.071389] usbcore: registered new interface driver ums-karma [ 56.081039] usbcore: registered new interface driver ums-sddr09 [ 56.098926] usbcore: registered new interface driver ums-sddr55 [ 56.121802] usbcore: registered new interface driver ums-usbat [ 56.161221] xt_time: kernel timezone is -0000 [ 56.383677] PPP generic driver version 2.4.2 [ 56.398462] urngd: v1.0.2 started. [ 56.403646] NET: Registered protocol family 24 [ 56.556529] ath: EEPROM regdomain: 0x0 [ 56.556541] ath: EEPROM indicates default country code should be used [ 56.556544] ath: doing EEPROM country→regdmn map search [ 56.556561] ath: country maps to regdmn code: 0x3a [ 56.556567] ath: Country alpha2 being used: US [ 56.556570] ath: Regpair used: 0x3a [ 56.571455] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 56.573485] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=13 [ 56.680215] kmodloader: done loading kernel modules from /etc/modules.d/* [ 56.891195] random: crng init done [ 69.753879] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 69.761291] eth0: link up (1000Mbps/Full duplex) [ 69.766101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 69.799278] br-lan: port 1(eth0.1) entered blocking state [ 69.804958] br-lan: port 1(eth0.1) entered disabled state [ 69.811021] device eth0.1 entered promiscuous mode [ 69.815978] device eth0 entered promiscuous mode [ 69.851595] br-lan: port 1(eth0.1) entered blocking state [ 69.857192] br-lan: port 1(eth0.1) entered forwarding state [ 69.863283] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 69.959393] br-lan: port 2(eth1) entered blocking state [ 69.964911] br-lan: port 2(eth1) entered disabled state [ 69.970757] device eth1 entered promiscuous mode [ 70.750367] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 72.770761] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 72.798752] br-lan: port 3(wlan0) entered blocking state [ 72.804478] br-lan: port 3(wlan0) entered disabled state [ 72.810540] device wlan0 entered promiscuous mode [ 73.072571] eth1: link up (100Mbps/Full duplex) [ 73.077329] br-lan: port 2(eth1) entered blocking state [ 73.082802] br-lan: port 2(eth1) entered forwarding state [ 79.992135] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 79.999024] br-lan: port 3(wlan0) entered blocking state [ 80.004628] br-lan: port 3(wlan0) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1