CloudEngine marketed different devices under the name “Pogoplug”, some of which even share the same outward appearance. This page is for the devices using the Oxnas/PLXtech SoC.
The “V3 Pro” version is marked “P01” or “P02” on the bottom, the non-“pro” “V3” version is marked “B01”, “B02”, “B03”, “B04”, “P21”, “P24”, or “P25”.
Devices marked “E02” share the same case but not the hardware, they can be found at their own target: Kirkwood Pogoplug E02
|↓ Model||Version||Current Release||Firmware OpenWrt Install||Firmware OpenWrt Upgrade|
|Pogoplug V3||B0*, P2*||19.07.4||http://downloads.openwrt.org/releases/19.07.4/targets/oxnas/ox820/||http://downloads.openwrt.org/releases/19.07.4/targets/oxnas/ox820/openwrt-19.07.4-oxnas-ox820-cloudengines_pogoplug-series-3-squashfs-sysupgrade.tar|
|Pogoplug V3 Pro||P01, P02||19.07.4||http://downloads.openwrt.org/releases/19.07.4/targets/oxnas/ox820/||http://downloads.openwrt.org/releases/19.07.4/targets/oxnas/ox820/openwrt-19.07.4-oxnas-ox820-cloudengines_pogoplugpro-squashfs-sysupgrade.tar|
Support for the OXNAS Pogoplugs has been added with OpenWrt 15.05. OpenWrt 15.05 and LEDE 17.01 required a u-boot version more capable than the vendor u-boot that comes with the Pogoplug. This required a rather convoluted installation process, resulting in either loading a suitably capable u-boot from the less capable vendor u-boot (a “2nd stage u-boot”) or outright replacing the vendor u-boot (which is rather dangerous).
With 18.06, the OXNAS target has been overhauled, one of the results is that it can now be booted from the vendor u-boot, no additional or replacement u-boot required anymore. One of the consequences of those significant changes is that you cannot upgrade from an older version than 18.06 to 18.06 or later using sysupgrade. If you try to force it, you will render your device unable to boot, you will need to go through the installation process outlined below.
All versions of OpenWrt 18.06 and 19.07 up to 19.07.2 contain a bug that prevents a proper boot after a reset. If you reset the device from OpenWrt it will hang at the subsequent boot and requires a physical power cycle. This bug has been fixed for OpenWrt 19.07.3 and in Snapshots after 2020-03-19.
In versions 18.06.0 through 18.06.2, pre-compiled “official” images did not contain a kernel image, resulting in an unbootable Pogoplug even if you followed the correct install process. Pre-built OpenWrt 18.06.0 to 18.06.2 images are broken and can not be used. This bug has been fixed in OpenWrt 18.06.3 and later.
Danger - live voltage!
A Pogoplug contains its own unenclosed power supply in the lower part of the case. When connected to power, parts inside the case are live at mains voltage and must be handled with extreme care!
Seriously, this could kill you if you're not careful. Please completely disconnect the Pogoplug from power before opening the case and working inside, and make really sure to not touch anything inside as long as the Pogoplug is powered.
You will need the following:
prodepending on your Pogoplug hardware, for brevity of this guide, the files are only referenced by the last part of the filename)
Open the serial connection and power on your Pogoplug. Once you see
Hit any key to stop autoboot: … hit any key to stop autoboot. You will be on the vendor u-boot command line, prompting you with
Permanently set up the bootloader's boot configuration to boot OpenWrt and configure U-Boot for the IP addresses we will use:
setenv bootcmd 'nboot 60500000 0 440000; bootm' setenv serverip 192.168.1.2 setenv ipaddr 192.168.1.1 saveenv
initramfs-uImage to uboot and start it using:
tftp 64000000 initramfs-uImage bootm 64000000
OpenWrt will start up, but for now will only reside in RAM (i.e. will be lost after a reboot.) While still connected via serial, press enter now to get a shell in OpenWrt.
Unlike with other devices, the ethernet interface will configured as DHCP by default. Set it to a static IP using:
uci set network.lan.proto=static uci set network.lan.ipaddr=192.168.1.1 uci set network.lan.netmask=255.255.255.0 uci commit service network restart
Using an SCP application (for example WinSCP) connect to OpenWrt at 192.168.1.1 and transfer the
squashfs-sysupgrade.tar image file OpenWrt's
/tmp directory. Install it permanently using
The Pogoplug will reboot, and via serial you should be able to observe it booting into your complete OpenWrt installation. Again, the default LAN configuration is DHCP, so either plug it into a router serving DHCP or, while you are still connected via serial, change the network configuration to a static IP.
If, for some reason, you want to install OpenWrt 18.06 you will need to do steps 2 and 3 two times, the first time with the
squashfs-ubinized.bin file which has to be forced in
sysupgrade -F. Then repeat steps 2 and 3 exactly as outlined above using the
Pogoplugs come with a serial header, populated with a Molex 70107 connector (as used with CD-ROM audio cables).
The settings for accessing the serial console are as follows:
Bits per second: 115200
Data bits: 8
Stop bits: 1
Flow control: None