Cisco RVS4000 v2

Small Business / Home Router with L7 IPS and NAT (both hardware accelerated), a VLAN capable switch.

This page has preliminary documentation for those wishing to help in getting OpenWrt firmware running on this hardware.

Version/Model Launch Date OpenWrt Version Supported Model Specific Notes
v1 ? unsupported
v2 ? unsupported
SoC Ram Flash Network USB Serial JTag
Cavium CNS1202 (Star Semiconductor STR9202) 64MiB 8MiB RTL8366 1GbE(WAN), 4GbE(LAN No Yes ?
  • Access the following site on the OEM WebInterface: http://192.168.1.1/Hidden_telnet.htm
  • Select enable and push save
  • Telnet on Port 23, username=admin, pwd=admin

Please check out the article flash.layout. It contains an example and a couple of explanations.

Original Layout

Linux version 2.4.27-star (root@localhost) (gcc version 2.95.3 20010315 (release)) #1 Tue Mar 16 11:23:54 CST 2010

  • 0x00000000-0x00020000 : “BootLoader ”
  • 0x00020000-0x00040000 : “System Configuration”
  • 0x00040000-0x00100000 : “Signature”
  • 0x00100000-0x00680000 : “Kernel”
Cisco RVS4000 V2 Flash Layout
Layer0 8MiB
Layer1 mtd0 BootLoader 128KiB mtd1 System Configuration 128KiB mtd2 Signature 1152KiB mtd3 Kernel 6784KiB

Terminal Upgrade Process

TBD

TBD

TBD

TBD

hardware.button on howto use and configure the hardware button(s).

It's been stated that the Cisco models RV220w and RV120w use the same CPU as this device.

Architecture ARM
Vendor Cavium Networks
bootloader ARMboot
System-On-Chip1 Cavium Networks / Star BroadWeb CNS1202 (STR 9202 CPU: FA526id(wb) rev 1 (v4l)
CPU1/Speed 250 MHz
Flash MXIC MX29LV640EBTI-70G
Flash Size 8192 KiB
RAM 2x EtronTec EM6AA160TSA-5G
RAM Size 64 MiB
Ethernet Vitesse VSC7385 (4 port) RTL8366RB Gigabit w/ vlan support swconfig
USB No
Serial Yes
JTAG Unknown
Device                        CNS1202
Part Number*                    "CNS1202-XXXBG304-Option Code "
"Parallel Flash"                    8/16-bit
Memory I/O                    16/32-bit
"Content Inspection Engine"        y
"Embedded Switch"                y
"Hardware NAT/NAPT"                y
"Interfaces: USB 1.1/2.0 PHY/CTL"    2 ports
Interfaces: PCMCIA                y
Interfaces: Ethernet                "2 x RGMII/MII"
PCI 2.2 Host                    "32-bit/66 MHz up to 3 devices"
Package                        BGA-304

port.serial general information about the serial port, serial port cable, etc.

Unpopulated J1 header is a 3.3V serial port that is the primary serial console. It's possible to solder a 3 pin header onto the PCB and access the serial console including the bootloader prompt, using an FTDI 3.3V serial-to-usb cable.

Pinout

  1. VDD (the [] marked pin)
  2. RX
  3. TX
  4. GND

Only RX TX and Ground are needed to use the terminal set up with 38400 baud, 8 data bits, no parity and one stop bit (38400 8N1). Uses 3.3V TTL.

It remains to be seen if there is any JTAG support on this board. There is no obvious unpopulated connector that could be JTAG.

You can (insanely) enable telnet access on all ports (WAN and LAN) by the web interface:

http://$ROUTER_IP/Hidden_telnet.htm

This is useful for poking around on your router without too much trouble.

ARMboot 1.1.0 (Mar 4 2010 - 15:27:17) Star maintain version 0.14.100000000 ARMboot code: 00000000 -> 0001aeb0 ARMboot code(Bin file):00000000 ->00016ca0 STR9100 CPU Clock: 250 MHz DDR Bank #0: 00000000 64 MB DDR Controller Data Bus Width: 32 bits Flash Dev.id = 22CB Flash Bank #1: 8 MB *** Using default environment ## Starting application at 0x01000000 ... Reset switch by gpio 10,low active RTL8366RB Chip version [3] Force RTL8366 MAC5 link up and 1000M Boot version 1.04 MAC Address:58-8d-09-e2-96-8e the product id is : 65 52 63 4F 6D 4D the pruduct ID check OK! ## Application terminated, rc = 0x0 Hit ENTRY to stop autoboot: 0 ## Starting application at 0x10160000 ... Uncompressing Linux..................... ARMboot 1.1.0 (Mar 4 2010 - 15:27:17) Star maintain version 0.14.100000000 ARMboot code: 00000000 -> 0001aeb0 ARMboot code(Bin file):00000000 ->00016ca0 STR9100 CPU Clock: 250 MHz DDR Bank #0: 00000000 64 MB DDR Controller Data Bus Width: 32 bits Flash Dev.id = 22CB Flash Bank #1: 8 MB *** Using default environment ## Starting application at 0x01000000 ... Reset switch by gpio 10,low active RTL8366RB Chip version [3] Force RTL8366 MAC5 link up and 1000M Boot version 1.04 MAC Address:58-8d-09-e2-96-8e the product id is : 65 52 63 4F 6D 4D the pruduct ID check OK! ## Application terminated, rc = 0x0 Hit ENTRY to stop autoboot: 0 STR9100>


## Starting application at 0x10160000 ... Uncompressing Linux....................................................................... done, booting the kernel. request_standard_resources()....OK trap_init().....OK init_IRQ().....OK sched_init().....OK softirq_init().....OK time_init().....OK Linux version 2.4.27-star (root@sbu-ii-1-server) (gcc version 2.95.3 20010315 (release)) #3 Thu May 12 16:07:18 CST 2011 CPU: FA526id(wb) revision 1 ICache:16KB enabled, DCache:16KB enabled, BTB support Machine: STAR_STR9100 MM: not creating mapping for 0x10000000 at 0x10000000 in user region On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram0 MEM=64 I-base_addr : c01d3000 IRQ Timer1 at interrupt number 0x0 and clock 125000000(Hz) console_init().....OK kmem_cache_init().....OK Calibrating delay loop... 192.10 BogoMIPS Memory: 64MB = 64MB total Memory: 57884KB available (1985K code, 435K data, 68K init) mem_init().....OK pgtable_cache_init().....OK proc_caches_init().....OK Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) vfs_caches_init().....OK Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) buffer_init().....OK Page-cache hash table entries: 16384 (order: 4, 65536 bytes) page_cache_init().....OK signals_init().....OK POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket do initcalls start Starting kswapd pty: 256 Unix98 ptys configured Str9100 Serial Driver version 5.05c (2001-07-08) with no serial options enabled ttyS00 at 0xf7800000 (irq = 10) is a Star_UART !!!RESET SWITCH RTL8366RB Chip version [3] RTL8366 force link and 1000M success! !!!Init default VLAN !!!Init ACL !!!Power save enable rxring.vir_addr=C4800000 rxring.phy_addr=00376000 txring.vir_addr=C4802000 txring.phy_addr=00350000 eth0: Switch Type: ONEARM(One Mac mode) [orn_drv_open_poll,3362] [orn_drv_open_poll,3368] [orn_drv_open_poll,3380] [orn_drv_open_poll,3397] Check MAC/PHY 0 Link Status : UP! [orn_drv_open_poll,3422] [orn_drv_open_poll,3443] Star9100 one arm Lan Port Bridge Mode Error : PORT0 is disabled [orn_drv_open_poll,3467] [orn_drv_open_poll,3473] gsw_info.vlan[0].vlan_vid : 3292 gsw_info.vlan[1].vlan_vid : 1 [orn_drv_open_poll,3522] [orn_drv_open_poll,3529] [orn_drv_open_poll,3543] [orn_drv_open_poll,3546] eth0: STAR9100 LAN Port Initial Finished eth1: STAR9100 WAN Port Initial Finished Enable AN STAR9100 EWC Project MAC1 Initial eth2: STAR9100 EWC Port Initial Finished RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 Amd/Fujitsu Extended Query Table v1.1 at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Creating 4 MTD partitions on "str9100_flash": 0x00000000-0x00020000 : "BootLoader " 0x00020000-0x00040000 : "System Configuration" 0x00040000-0x00160000 : "Signature" 0x00160000-0x00800000 : "Kernel" IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 4096) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver Linux IP multicast router 0.06 plus PIM-SM klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: cvs2006Jan12_11:29:56 klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=251) klips_info:ipsec_alg_init: calling ipsec_alg_static_init() ipsec_aes_init(alg_type=15 alg_id=12 name=aes): ret=0 ipsec_aes_init(alg_type=14 alg_id=9 name=aes_mac): ret=0 ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0 netfilter PSD loaded - (c) astaro AG ipt_random match loaded NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. ip6_tables: (C) 2000-2002 Netfilter core team Str9100 Information inited STAR9100 Software HNAT Driver Initialed NetWinder Floating Point Emulator V0.97 (double precision) do initcalls end RAMDISK: Compressed image found at block 0 Freeing initrd memory: 4349K VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 68K UART IRQ_ports = c02370d8 UART IRQ at interrupt number 0xa init started: BusyBox v1.00 (2011.05.12-08:02+0000) multi-call binary init started: BusyBox v1.00 (2011.05.12-08:02+0000) multi-call binary Starting pid 9, console /dev/ttyS0: '/etc/init.d/rc.sysinit' Mounting root fs rw ... Mounting other filesystems ... mount: Mounting none on /proc/bus/usb failed: No such file or directory Sysinit done Call /etc/rcS... Using /usr/sbin/led.o Using /usr/sbin/push_button.o Using /lib/modules/ipt_DLOG.o Using /lib/modules/ipt_webstr.o Using /lib/modules/ipt_http_string.o Using /lib/modules/ipt_multi_match.o Using /lib/modules/ipt_multiaddr.o Using /lib/modules/ipt_httpMETHOD.o * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=vlan action=start /bin/cp /proc/uptime /tmp/var/run/rc.vlan.run rc starting vlan... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=port action=start /bin/cp /proc/uptime /tmp/var/run/rc.port.run rc starting port... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=initqos action=start /bin/cp /proc/uptime /tmp/var/run/rc.initqos.run rc starting initqos... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=qos action=start /bin/cp /proc/uptime /tmp/var/run/rc.qos.run rc starting qos... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=wan_mac action=start /bin/cp /proc/uptime /tmp/var/run/rc.wan_mac.run rc starting wan_mac... /sbin/ifconfig eth1 up install_isr * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=lan action=start /bin/cp /proc/uptime /tmp/var/run/rc.lan.run rc starting lan... /sbin/ifconfig eth0 172.16.72.1 netmask 255.255.255.0 eth0:star9100_gsw1000_lan_open star9100_gsw1000_lan_open Exit!! not install_isr /bin/echo "lanip 172.16.72.1" >/proc/star9100_shnat_setting /bin/echo "interswitch lanip:172.16.72.1/24" >/proc/str9100/shnat iptables -t nat -I PREROUTING -i eth0 -s 172.16.72.1/255.255.255.0 -d 172.16.72.1 -p tcp --dport 443 -j DNAT --to 172.16.72.1:30443 iptables -t nat -I PREROUTING -i eth0 -s 172.16.72.1/255.255.255.0 -d 172.16.72.1 -p udp --dport 53 -j DNAT --to 8.8.8.8 * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=printk action=start /bin/cp /proc/uptime /tmp/var/run/rc.printk.run rc starting printk... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=syslogd action=start /bin/cp /proc/uptime /tmp/var/run/rc.syslogd.run rc starting syslogd... /sbin/syslogd -f /etc/syslog.conf * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=httpd action=start /bin/cp /proc/uptime /tmp/var/run/rc.httpd.run rc starting httpd... /bin/rm -f /tmp/www /bin/ln -s -f /www.eng /tmp/www /usr/sbin/mini_httpd -d /tmp/www -r "Router" -c '*.cgi' -t 1800 -i /var/run/mini_httpd.pid -a Digest -S -E /usr/sbin/certSrv.pem & bind: Address already in use * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcpd action=start /bin/cp /proc/uptime /tmp/var/run/rc.dhcpd.run rc starting dhcpd... /bin/echo "1:21500076:16777215;0:1:1:1:1" >/proc/vid_config /usr/sbin/udhcpd /etc/udhcpd.conf& * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcp-fwd action=start /bin/cp /proc/uptime /tmp/var/run/rc.dhcp-fwd.run /bin/cp /proc/uptime /tmp/var/run/rc.dhcp-fwd.run rc starting dhcp-fwd... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=route action=start /bin/cp /proc/uptime /tmp/var/run/rc.route.run rc starting route... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ripd action=start /bin/cp /proc/uptime /tmp/var/run/rc.ripd.run rc starting ripd... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=natpt action=start /bin/cp /proc/uptime /tmp/var/run/rc.natpt.run /bin/cp /proc/uptime /tmp/var/run/rc.natpt.run rc starting natpt... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcp6 action=start /bin/cp /proc/uptime /tmp/var/run/rc.dhcp6.run rc starting dhcp6... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * start wan init=0 /sbin/ifconfig eth1 up /sbin/ifconfig eth1 mtu 1460 /sbin/ifconfig eth1 192.168.4.2 netmask 255.255.255.0 /sbin/route del default route: SIOC[ADD|DEL]RT: No such process /sbin/route add default gw 192.168.4.1 echo nameserver 192.168.4.1>>/etc/resolv.conf /bin/cp /proc/uptime /tmp/wan_uptime /usr/sbin/rc dhcpd create * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcpd action=create /bin/cp /proc/uptime /tmp/var/run/rc.dhcpd.run /bin/echo "1:21500076:16777215;0:1:1:1:1" >/proc/vid_config /usr/sbin/rc service restart * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=(null) action=restart rc ntp stop * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ntp action=stop /bin/cp /proc/uptime /tmp/var/run/rc.ntp.run /usr/bin/killall ntp killall: ntp: no process killed route del default gw 192.168.4.1 /usr/sbin/fw-scripts/firewall stop .: 19: Can't open /tmp/firewall.conf killall: dnrd: no process killed /usr/bin/killall IGMPProxy killall: IGMPProxy: no process killed /usr/sbin/tc qdisc del dev eth0 root RTNETLINK answers: No such file or directory /usr/sbin/tc qdisc del dev eth1 root RTNETLINK answers: No such file or directory /usr/sbin/iptables -F -t mangle iptables -t nat -I PREROUTING -i eth0 -s 172.16.72.1/255.255.255.0 -d 172.16.72.1 -p tcp --dport 443 -j DNAT --to 172.16.72.1:30443 iptables -t nat -I PREROUTING -i eth0 -s 172.16.72.1/255.255.255.0 -d 172.16.72.1 -p udp --dport 53 -j DNAT --to 8.8.8.8 /usr/bin/killall dhcp-fwd >/dev/null 2>&1 killall -SIGINT routed killall: routed: no process killed sh: /user/sbin/iptables: not found /usr/bin/killall syslogd killall: LicMgm: no process killed rc starting wan_basic... rc ntp start * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ntp action=start /bin/cp /proc/uptime /tmp/var/run/rc.ntp.run rc starting ntp... /usr/sbin/ntp -z GMT-5 0 14& rc dhcp6 restart * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcp6 action=restart /bin/cp /proc/uptime /tmp/var/run/rc.dhcp6.run /usr/bin/killall dhcp6-serv killall: dhcp6-serv: no process killed rc starting dhcp6... route add default gw 192.168.4.1 dev eth1 /bin/echo "lanip 172.16.72.1" >/proc/star9100_shnat_setting /bin/echo "wanip 192.168.4.2" >/proc/star9100_shnat_setting rc starting dns... rc starting firewall... iptables -t nat -F cp /etc/crontab /etc/crontab.policy echo "vserver clean" > /proc/star9100_shnat_setting /usr/sbin/fw-scripts/firewall start iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/ipsec spi --clear /usr/sbin/ipsec eroute --clear /usr/sbin/ipsec whack --shutdown whack: Pluto is not running (no "/var/run/pluto/pluto.ctl") /sbin/ifconfig ipsec0 down /usr/sbin/ipsec tncfg --clear /usr/sbin/iptables -D INPUT -p udp --dport 500 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/iptables -D INPUT -p udp --dport 4500 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/iptables -D INPUT -p esp -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/iptables -t nat -D PREROUTING -p udp --dport 500 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/iptables -t nat -D PREROUTING -p udp --dport 4500 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) /usr/sbin/iptables -t nat -D PREROUTING -p esp -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) vpn down null complete./usr/bin/killall ssl_server killall: ssl_server: no process killed gateway==[192.168.4.1] VPN parse_conf Error!! index=-1 Error Number=-3 eth1,192.168.4.2,255.255.255.0,192.168.4.255,192.168.4.1 /usr/sbin/ipsec spi --clear /usr/sbin/ipsec eroute --clear /usr/sbin/iptables -I INPUT -p udp --dport 500 -j ACCEPT /usr/sbin/iptables -I INPUT -p udp --dport 4500 -j ACCEPT /usr/sbin/iptables -I INPUT -p esp -j ACCEPT /usr/sbin/iptables -t nat -I PREROUTING -p udp --dport 500 -j ACCEPT /usr/sbin/iptables -t nat -I PREROUTING -p udp --dport 4500 -j ACCEPT /usr/sbin/iptables -t nat -I PREROUTING -p esp -j ACCEPT /bin/echo 0 > /proc/sys/net/ipv4/conf/all/rp_filter /usr/sbin/ipsec tncfg --attach --virtual ipsec0 --physical eth1 /sbin/ifconfig ipsec0 192.168.4.2 broadcast 192.168.4.255 netmask 255.255.255.0 /usr/sbin/ipsec pluto --secretsfile /etc/ipsec.secrets --nat_traversal --uniqueids --adns /usr/local/libexec/ipsec/_pluto_adns Jan 1 00:00:30 pluto[425]: Starting Pluto (Openswan Version cvs2006Jan12_11:29:56 X.509-1.5.4 PLUTO_SENDS_VENDORID PLUTO_USES_KEYRR; Vendor ID OE@ECqImzhFD) vpn_up_null up. /usr/sbin/ssl_server & /usr/bin/killall IGMPProxy >/dev/null 2>&1 Jan 1 00:00:30 pluto[425]: @(#) built on May 12 2011:16:06:15: Jan 1 00:00:30 pluto[425]: Setting NAT-Traversal port-4500 floating to on Jan 1 00:00:30 pluto[425]: port floating activation criteria nat_t=1/port_fload=1 Jan 1 00:00:30 pluto[425]: including NAT-Traversal patch (Version 0.6c) Jan 1 00:00:30 pluto[425]: ike_alg_register_enc(): Activating OAKLEY_AES_CBC: Ok (ret=0) Jan 1 00:00:30 pluto[425]: starting up 1 cryptographic helpers Jan 1 00:00:30 pluto[425]: started helper pid=430 (fd:4) the function is main,the line is 94,the file is serv.c the function is main,the line is 100,the file is serv.c the function is main,the line is 104,the file is serv.c the function is main,the line is 108,the file is serv.c the function is main,the line is 111,the file is serv.c Jan 1 00:00:30 pluto[425]: Using KLIPS IPsec interface code on 2.4.27-star /usr/bin/killall utelnetd > /dev/null 2>&1 Jan 1 00:00:30 pluto[425]: Changing to directory '/etc/ipsec.d/cacerts' Jan 1 00:00:30 pluto[425]: Changing to directory '/etc/ipsec.d/aacerts' Jan 1 00:00:30 pluto[425]: Changing to directory '/etc/ipsec.d/ocspcerts' Jan 1 00:00:30 pluto[425]: Changing to directory '/etc/ipsec.d/crls' Jan 1 00:00:30 pluto[425]: Warning: empty directory /bin/echo "I" > /proc/led /sbin/rmmod ip_nat_sip rmmod: ip_nat_sip: No such file or directory /sbin/rmmod ip_conntrack_sip rmmod: ip_conntrack_sip: No such file or directory cp /etc/crontab.policy /etc/crontab iptables -F ip_filter ip link set dev eth1 multicast on rc starting dhcp-fwd... rc starting ddns... rc starting ripd... rc starting pppoe_rule... rc starting pppoe_unNB_IP... /usr/bin/killall -SIGUSR2 udhcpd /etc/rcS: 75: /usr/sbin/wizd: not found * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=upnp action=start /bin/cp /proc/uptime /tmp/var/run/rc.upnp.run rc starting upnp... /bin/echo "lanip 172.16.72.1" >/proc/star9100_shnat_setting /bin/echo "wanip 192.168.4.2" >/proc/star9100_shnat_setting /usr/bin/killall -9 upnpd killall: upnpd: no process killed Using /usr/sbin/led.o insmod: A module named led already exists * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ips action=start /bin/cp /proc/uptime /tmp/var/run/rc.ips.run rc starting ips... Using /root/kris.o /bin/echo i1 > /proc/led kris daemon version 1.7 the function is main,the line is 94,the file is serv.c the function is main,the line is 100,the file is serv.c the function is main,the line is 104,the file is serv.c the function is main,the line is 108,the file is serv.c the function is main,the line is 111,the file is serv.c * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=radvd action=start /bin/cp /proc/uptime /tmp/var/run/rc.radvd.run rc starting radvd... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=LicMgm action=start /bin/cp /proc/uptime /tmp/var/run/rc.LicMgm.run rc starting LicMgm... Sum=0x01C426B7,InvSum=0xFE3BD949,Result=0x00000000 killall: LicMgm: no process killed Kris Rule Version 1.42 * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=snmp action=start /bin/cp /proc/uptime /tmp/var/run/rc.snmp.run => AcquireBasicData(UDI=C78A32118C603FB6D362C8440F79081F145A98AA4B771687694FC50468BB2C2E06D07E) Start TMZ_request_HTTP() rc starting snmp... /usr/bin/killall snmp killall: snmp: no process killed * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=sigmail action=start /bin/cp /proc/uptime /tmp/var/run/rc.sigmail.run rc starting sigmail... Donot send signature email duto no email information! * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=vpn_netbios action=start /bin/cp /proc/uptime /tmp/var/run/rc.vpn_netbios.run rc starting vpn_netbios... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=http_HNAT action=start /bin/cp /proc/uptime /tmp/var/run/rc.http_HNAT.run rc starting http_HNAT... echo "table alg add sport:80" > /proc/star9100_shnat_setting * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=radius action=start /bin/cp /proc/uptime /tmp/var/run/rc.radius.run rc starting radius... * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=rstp action=start /bin/cp /proc/uptime /tmp/var/run/rc.rstp.run rc starting rstp... Starting pid 532, console /dev/ttyS0: '/bin/sh' BusyBox v1.00 (2011.05.12-08:02+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. #


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2019/10/02 18:14
  • by tmomas