Cisco DPC3825/EPC3825

BCM338031 TP0 1 Sync:1 346890 SA BootLoader Version: 2.3.0_R3(S) Release Gnu spiboot reduced DDR drive Build Date: Sep 21 2009 Build Time: 15:57:39 SPI flash ID 0x010216, size 8MB, block size 64KB, write buffer 256, busy bit 1 Found image 1 at offset 20000 eCos - hal_diag_init Init device '/dev/BrcmTelnetIoDriver' Init device '/dev/ttydiag' Init tty channel: 81138f30 Init device '/dev/tty0' Init tty channel: 81138f50 Init device '/dev/haldiag' HAL/diag SERIAL init Init device '/dev/ser0' BCM 33XX SERIAL init - dev: 0.2 Set output buffer - buf: 0x811ed050 len: 4096 Set input buffer - buf: 0x811ee050 len: 4096 BCM 33XX SERIAL config LsSpiInit 3380 [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver... detecting flash3... [00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0x10216 [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions: (Flash Driver C API) WARNING - Permanent NonVol would fit in the boot block of this flash device, but I found existing NonVol in the following block; using this location instead... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver... ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully. [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices... Detecting the next image number that we will store to by default... Bootloader indicates we are running image 1 By default, we will dload to image number 2! [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully. BcmCmDocsisCtlThread::GetSingletonInstance: WARNING - the singleton is NULL, and someone is accessing it! BcmCmDocsisCtlThread::GetSingletonInstance: WARNING - the singleton is NULL, and someone is accessing it! SAHttpCacheVariables::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! Setting up the SAHttpCacheVariables singleton pointer. CmSnmpNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! CmSnmpNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! CmSnmpNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! BcmCmSANonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! Reading Permanent settings from non-vol... Checksum for permanent settings: 0x3f63b379 [00:00:02 01/01/1970] [tStartup] BcmMessageLogNonVolSettings::ReadFromImpl: (User Interface NonVol Settings) WARNING - Read older version of the settings (0.2); they have been upgraded to version 0.3, preserving original settings. [00:00:02 01/01/1970] [tStartup] BcmHalIfNonVolSettings::ReadFromImpl: (HalIf NonVol Settings) WARNING - Read older version of the settings (0.20); they have been upgraded to version 0.21, preserving original settings. [00:00:02 01/01/1970] [tStartup] BcmWiFi80211NonVolSettings::ReadFromImpl: (WiFi 802.11 NonVol Settings) WARNING - Read older version of the settings (0.8); they have been upgraded to version 0.10, preserving original settings. [00:00:02 01/01/1970] [tStartup] BcmCmDocsis30NonVolSettings::ReadFromImpl: (CM DOCSIS 3.0 NonVol Settings) WARNING - Read older version of the settings (0.1); they have been upgraded to version 0.2, preserving original settings. [00:00:02 01/01/1970] [tStartup] BcmCmSANonVolSettings::ReadFromImpl: (CM SA NonVol Settings) WARNING - Read older version of the settings (0.9); they have been upgraded to version 0.11, preserving original settings. [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (CWMP Client NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (CWMP Client State NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (PBCA Content Filter NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (PBCA Time Blocking NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (PBCA Captive Portal NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (PBCA Bandwidth Monitor NonVol Settings) Permanent settings are default! [00:00:02 01/01/1970] [tStartup] BcmeRouterNonVolSettings::IsDefault: (eRouter NonVol Settings) Permanent settings are default! * * * One or more of the settings groups was missing, possibly as a result of a code upgrade. * * * * * One or more of the settings groups was upgraded. * * Settings were read and verified. Reading Dynamic settings from non-vol... Checksum for dynamic settings: 0xed641955 [00:00:02 01/01/1970] [tStartup] CwmpClientNonVolSettings::ReadFromImpl: Read 0 domain entries [00:00:02 01/01/1970] [tStartup] BcmCmSANonVolSettings::BcmCmSANonVolSettings: (CM SA NonVol Settings) WARNING - Setting up SA event log supported in CxC 3.9.x! (EventLogIsUsed = 1) Load ATMEL Test image = Disable we found one in the table already!!!! Settings were read and verified. Non-Vol Settings successfully written to the device. [00:00:02 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Setting FPM Buffer size to: 2048 Base Address: 0x82edbee0 [00:00:02 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: fFpmLargestBufferSize: 2048 fFpmSizeShiftBits: 0xb [00:00:02 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Pool index: 0 pool size: 2048 [00:00:02 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Lookup table index: 0 pool size: 0 ------------------------------------ Free Pool Manager Configuration ------------------------------------ Buffer size in Bytes............... 2048 Number of Tokens................... 8192 Base Address of FPM Memory ........ 0xb2010200 Base Address of FPM Mem in DDR2.... 0x82edbee0 Total Configured FPM Memory Size... 16777216 Free Fifo Full..................... 0 Free Fifo Empty.................... 1 Alloc Fifo Full.................... 0 Alloc Fifo Empty................... 0 Number of tokens available......... 8192 Number of not valid token frees.... 0 Number of not valid token multi.... 0 Overflow Count..................... 0 Underflow Count.................... 0 [00:00:02 01/01/1970] [tStartup] BcmBfcPacketAlloc::Init: Packet Alloc Header Buffer Start Addr: 0x82d5bec0 Length: 0x180000 Max Buffer Size: 0xc0 [00:00:02 01/01/1970] [tStartup] BcmThread::BcmPanasonicSnoop: (BFC Ping Thread) WARNING - Singleton pointer is not NULL! There are multiple BcmParentalCtlThread devices! Leaving the singleton pointer alone... [00:00:02 01/01/1970] [Telnet Thread] BcmTelnetThread::ThreadMain: (Telnet Thread) Telnet server thread running... [00:00:02 01/01/1970] [SSH Thread] BcmThread::ThreadMain: (SSH Thread) SSH server thread running... [00:00:02 01/01/1970] [NonVol Device Async Helper] CwmpClientNonVolSettings::WriteToImpl: Wrote Impl Allowed List size 0 [00:00:02 01/01/1970] [NonVol Device Async Helper] CwmpClientNonVolSettings::WriteToImpl: Wrote Impl Allowed List size 0 [00:00:02 01/01/1970] [NonVol Device Async Helper] CwmpClientNonVolSettings::WriteToImpl: Wrote Impl Allowed List size 0 [00:00:03 01/01/1970] [NonVol Device Async Helper] CwmpClientNonVolSettings::WriteToImpl: Wrote Impl Allowed List size 0 Creating SNMP agent cablemodem agent cablemodem agent disabling management. cablemodem agent defering traps. [00:00:03 01/01/1970] [tStartup] BcmCmDocsisApplication::CreateAndRegisterCommandTables: (CM DOCSIS Application) Creating/registering CWMP command table If you pressed the 's' key before this point, we will skip driver initialization... Creating DOCSIS Control Thread... 0x83efb458 0x83efb388 0x83efb2d0 0x83efb218 0x82d598dc 0x82d59824 0x82d5976c 0x82d596b4 vvv Interface creation and driver startup beginning vvv -> Begin DOCSIS CM WAN interface Creating HAL object for the DOCSIS CableModem interface Registering DOCSIS CableModem driver Initializing main DTP DQM interrupts. b4201000: 0000004c b4201004: 00000000 b4201008: 00000008 b420100c: 00000000 b4201010: 00000000 b4201014: 00000000 b4201018: 00000000 b420101c: 00000000 Creating a new host FAP DQM manager. Instance: 82d2b6ec Initializing main FAP DQM interrupts. b8401000: 00000000 b8401004: 00000000 b8401008: 00000008 b840100c: 00000000 b8401010: 00000000 b8401014: 00000000 b8401018: 00000000 b840101c: 00000000 Creating a new host FAP DQM manager. Instance: 82d2b600 Creating a new host UTP DQM manager. Instance: 82d27470 Initializing main UTP DQM interrupts. b8001000: 0000000d b8001004: 00000000 b8001008: 00000008 b800100c: 00000000 b8001010: 00000001 b8001014: 00000000 b8001018: 00000000 b800101c: 00000000 LNA Detected = BCM3410 Initial Boost Status=0. Tilt Status=0 (Boost=Tilt=1)LNA Gain = 0x1f Final(Boost/Tilt=1/0) STATUS_READ2_REG=0x101f. Initializing all 8 downstreams - this takes a while. Patience, Grasshopper... 1 2 3 4 5 6 7 8 Fxtal is 48000000 Fclk_us_vco is 2088000000 Fclk_us_pll is 522000000 Fxtal is 48000000 Fclk_us_vco is 2088000000 Fclk_us_pll is 522000000 Fxtal is 48000000 Fclk_us_vco is 2088000000 Fclk_us_pll is 522000000 Fxtal is 48000000 Fclk_us_vco is 2088000000 Fclk_us_pll is 522000000 Fxtal is 48000000 Fclk_us_vco is 2088000000 Fclk_us_pll is 522000000 BcmMacInit: advMapRunAheadTimeMin = 3584 (0x00000e00) 10.24 MHz ticks, 350 usec Initializing DS Docsis 3.0 MAC Initializing CalcPhyPico BcmInitCalcPhyPico:Copying CalcPhy PicoCode rev 1.1.0 : 06/25/07 ...................................................................... Verifying CalcPhy PicoCode. ...................................................................... BcmInitCalcPhyPico:PicoCode verified. Creating a new host UTP DQM manager. Instance: 82ce5c30 Creating a new host UTP DQM manager. Instance: 82ce5b5c [00:00:13 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, bitmask=0x3 [00:00:13 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, US size=64, DS size=256 bytes. -> End DOCSIS CM WAN interface -> Begin Ethernet LAN interfaces Creating HAL object for the Eth-Switch Lan(1) interface Registering Eth-Switch Lan(1) driver Creating a new host MSG PROC DQM manager. Instance: 82ce5460, DQM_REGS = b8801800, CTRL_REGS = b8801000 Initializing main MSG_PROC DQM interrupts. b8801000: 00000000 b8801004: 00000000 b8801008: 00000008 b880100c: 00000000 b8801010: 00000000 b8801014: 00000000 b8801018: 00000000 b880101c: 00000000 ... initializing QAMTUNER REF PLL Creating a new host MSG PROC DQM manager. Instance: 82ce3e60, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82ce3d8c, DQM_REGS = b8801800, CTRL_REGS = b8801000 **** SETTING PHY DEFAULTS **** **** PEFORMING PHY CHECK **** Ethernet Link Down! Creating a new host MSG PROC DQM manager. Instance: 82ce3cb8, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82ce3be4, DQM_REGS = b8801800, CTRL_REGS = b8801000 AR8316: No mask is needed(00700000). AR8316: Reset the switch, wait.done! Configure AR8316 **** SETTING PHY DEFAULTS **** **** PEFORMING PHY CHECK **** Configure AR8316 Successfully!... Ethernet LinCreating a new host MSG PROC DQM manager. Instance: 82ce0928, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82ce0854, DQM_REGS = b8801800, CTRL_REGS = b8801000 k Up! Autonegotiation Not Completed! Speed is 1000 MBps Full Duplex. Add 01:00:5E:00:00:01 on port 0: OK Add 01:00:5E:00:00:01 on port 1: OK Add 01:00:5E:00:00:01 on port 2: OK Add 01:00:5E:00:00:01 on port 3: OK Add 01:00:5E:00:00:01 on port 4: OK Add 01:00:5E:00:00:01 on port 5: OK Add 01:00:5E:00:00:02 on port 0: OK Add 01:00:5E:00:00:02 on port 1: OK Add 01:00:5E:00:00:02 on port 2: OK Add 01:00:5E:00:00:02 on port 3: OK Add 01:00:5E:00:00:02 on port 4: OK Add 01:00:5E:00:00:02 on port 5: OK Add 01:00:5E:00:00:0D on port 0: OK Add 01:00:5E:00:00:0D on port 1: OK Add 01:00:5E:00:00:0D on port 2: OK Add 01:00:5E:00:00:0D on port 3: OK Add 01:00:5E:00:00:0D on port 4: OK Add 01:00:5E:00:00:0D on port 5: OK Add 01:00:5E:00:00:16 on port 0: OK Add 01:00:5E:00:00:16 on port 1: OK Add 01:00:5E:00:00:16 on port 2: OK Add 01:00:5E:00:00:16 on port 3: OK Add 01:00:5E:00:00:16 on port 4: OK Add 01:00:5E:00:00:16 on port 5: OK Add 01:00:5E:7F:FF:FA on port 0: OK Add 01:00:5E:7F:FF:FA on port 1: OK Add 01:00:5E:7F:FF:FA on port 2: OK Add 01:00:5E:7F:FF:FA on port 3: OK Add 01:00:5E:7F:FF:FA on port 4: OK Add 01:00:5E:7F:FF:FA on port 5: OK Add 01:00:5E:00:00:FB on port 0: OK Add 01:00:5E:00:00:FB on port 1: OK Add 01:00:5E:00:00:FB on port 2: OK Add 01:00:5E:00:00:FB on port 3: OK Add 01:00:5E:00:00:FB on port 4: OK Add 01:00:5E:00:00:FB on port 5: OK Add 01:00:5E:00:00:01 on port 0: OK Add 01:00:5E:00:00:01 on port 1: OK Add 01:00:5E:00:00:01 on port 2: OK Add 01:00:5E:00:00:01 on port 3: OK Add 01:00:5E:00:00:01 on port 4: OK Add 01:00:5E:00:00:01 on port 5: OK Add 01:00:5E:00:00:02 on port 0: OK Add 01:00:5E:00:00:02 on port 1: OK Add 01:00:5E:00:00:02 on port 2: OK Add 01:00:5E:00:00:02 on port 3: OK Add 01:00:5E:00:00:02 on port 4: OK Add 01:00:5E:00:00:02 on port 5: OK Add 01:00:5E:00:00:0D on port 0: OK Add 01:00:5E:00:00:0D on port 1: OK Add 01:00:5E:00:00:0D on port 2: OK Add 01:00:5E:00:00:0D on port 3: OK Add 01:00:5E:00:00:0D on port 4: OK Add 01:00:5E:00:00:0D on port 5: OK Add 01:00:5E:00:00:16 on port 0: OK Add 01:00:5E:00:00:16 on port 1: OK Add 01:00:5E:00:00:16 on port 2: OK Add 01:00:5E:00:00:16 on port 3: OK Add 01:00:5E:00:00:16 on port 4: OK Add 01:00:5E:00:00:16 on port 5: OK Add 01:00:5E:7F:FF:FA on port 0: OK Add 01:00:5E:7F:FF:FA on port 1: OK Add 01:00:5E:7F:FF:FA on port 2: OK Add 01:00:5E:7F:FF:FA on port 3: OK Add 01:00:5E:7F:FF:FA on port 4: OK Add 01:00:5E:7F:FF:FA on port 5: OK Add 01:00:5E:00:00:FB on port 0: OK Add 01:00:5E:00:00:FB on port 1: OK Add 01:00:5E:00:00:FB on port 2: OK Add 01:00:5E:00:00:FB on port 3: OK Add 01:00:5E:00:00:FB on port 4: OK Add 01:00:5E:00:00:FB on port 5: OK Number of Managed Switched Ports = 4 Creating HAL object for the Eth-Switch Lan(2) interface Registering Eth-Switch Lan(2) driver ... initializing QAMTUNER REF PLL Creating a new host MSG PROC DQM manager. Instance: 82ce03d0, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82ce02fc, DQM_REGS = b8801800, CTRL_REGS = b8801000 **** SETTING PHY DEFAULTS **** **** PEFORMING PHY CHECK **** Ethernet Link Down! Creating HAL object for the Eth-Switch Lan(3) interface Registering Eth-Switch Lan(3) driver ... initializing QAMTUNER REF PLL Creating a new host MSG PROC DQM manager. Instance: 82cdfe78, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82cdfda4, DQM_REGS = b8801800, CTRL_REGS = b8801000 **** SETTING PHY DEFAULTS **** **** PEFORMING PHY CHECK **** Ethernet Link Down! Creating HAL object for the Eth-Switch Lan(4) interface Registering Eth-Switch Lan(4) driver ... initializing QAMTUNER REF PLL Creating a new host MSG PROC DQM manager. Instance: 82cdf920, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 82cdf84c, DQM_REGS = b8801800, CTRL_REGS = b8801000 **** SETTING PHY DEFAULTS **** **** PEFORMING PHY CHECK **** Ethernet Link Down! -> End Ethernet LAN interfaces -> Begin 802.11 WiFi LAN interface instance 0 Creating HAL object for 802.11 RF (WiFi) interface #100 Registering 802.11 RF (WiFi)(0)(0) Primary driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (0) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 WiFi GPIO Configuration WiFi Device ID = 4357, Wifi Board Rev = 1200 Using: Reference Design Table Entry = 4 Push Button: Host GPIO, Pin 0, Assert Level 0 Activity LED: WiFi GPIO, Pin 1, Assert Level 0 WPS 1 LED: WiFi GPIO, Pin 2, Assert Level 1 WPS 2 LED: UNDEFINED Vendor LED: UNDEFINED Error LED: UNDEFINED PCie Power On: UNDEFINED GPIO Extra Config: Reg Offset: 0x28, Mask Vale: 0x8000, Config Value: 0x8000 ReconfigureDriver restartOption 1 called by StartDriver:597 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== ---------------------> wl_add_if: wlif->ifname (wl0.1) IfIndex (1) ---------------------> wl_add_if: wlif->ifname (wl0.2) IfIndex (2) ---------------------> wl_add_if: wlif->ifname (wl0.3) IfIndex (3) ---------------------> wl_add_if: wlif->ifname (wl0.4) IfIndex (4) ---------------------> wl_add_if: wlif->ifname (wl0.5) IfIndex (5) ---------------------> wl_add_if: wlif->ifname (wl0.6) IfIndex (6) ---------------------> wl_add_if: wlif->ifname (wl0.7) IfIndex (7) wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #101 Registering 802.11 RF (WiFi)(0)(1) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (1) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #102 Registering 802.11 RF (WiFi)(0)(2) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (2) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #103 Registering 802.11 RF (WiFi)(0)(3) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (3) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #104 Registering 802.11 RF (WiFi)(0)(4) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (4) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #105 Registering 802.11 RF (WiFi)(0)(5) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (5) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #106 Registering 802.11 RF (WiFi)(0)(6) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (6) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #107 Registering 802.11 RF (WiFi)(0)(7) MBSS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (7) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 ReconfigureDriver restartOption 1 called by StartDriver:610 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 ReconfigureDriver restartOption 1 called by StartDriver:710 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support ===> *** DRIVER *** <=== wlconf: PHYTYPE: 4 Creating HAL object for 802.11 RF (WiFi) interface #108 Registering 802.11 RF (WiFi)(0)(8) WDS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (8) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 Creating HAL object for 802.11 RF (WiFi) interface #109 Registering 802.11 RF (WiFi)(0)(9) WDS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (9) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 Creating HAL object for 802.11 RF (WiFi) interface #110 Registering 802.11 RF (WiFi)(0)(10) WDS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (10) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 Creating HAL object for 802.11 RF (WiFi) interface #111 Registering 802.11 RF (WiFi)(0)(11) WDS driver WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.2.2.2 on Vendor CM Agent w/ BRCM Factory Support DriverEntry: Creating adapter (11) on instance (0), name = WIFI Instance 0 Hal80211NiInit: Called! instance = 0 nas_main: Thread creation ok nas_main: Thread start ok BcmWpsPBCThread: Thread creation ok wpsPBC_main: Thread start ok BcmWiFi80211NiHalIf::PrefetchMacAddresses -> End 802.11 WiFi LAN interfaces. -> Begin IP Stack interfaces -> Starting BFC DHCP Client subsystem... -> Starting BFC DHCPv6 Client subsystem... Creating HAL object for IP Stack1 (MAC Addr=38:c8:5c:7e:95:be) DHCPc: Created default DHCP lease for IP Stack1 using client id htype=255, value=5c 7e 95 be 00 03 00 01 38 c8 5c 7e 95 be; auto-config enabled (IP, subnet, router). Registering IP Stack1 driver Tcpip NI: Init - RegisteredStackCount = 1 Creating HAL object for IP Stack2 (MAC Addr=00:09:5b:ed:da:02) DHCPc: Created default DHCP lease for IP Stack2 using client id htype=255, value=5b ed da 02 00 03 00 01 00 09 5b ed da 02; auto-config enabled (IP, subnet, router). Registering IP Stack2 driver Tcpip NI: Init - RegisteredStackCount = 2 Creating HAL object for IP Stack3 (MAC Addr=38:c8:5c:7e:95:c1) DHCPc: Created default DHCP lease for IP Stack3 using client id htype=255, value=5c 7e 95 c1 00 03 00 01 38 c8 5c 7e 95 c1; auto-config enabled (IP, subnet, router). Registering IP Stack3 driver Tcpip NI: Init - RegisteredStackCount = 3 Creating HAL object for IP Stack4 (MAC Addr=38:c8:5c:7e:95:c2) DHCPc: Created default DHCP lease for IP Stack4 using client id htype=255, value=5c 7e 95 c2 00 03 00 01 38 c8 5c 7e 95 c2; auto-config enabled (IP, subnet, router). Registering IP Stack4 driver Tcpip NI: Init - RegisteredStackCount = 4 Creating HAL object for IP Stack5 (MAC Addr=38:c8:5c:7e:95:c0) DHCPc: Created default DHCP lease for IP Stack5 using client id htype=255, value=5c 7e 95 c0 00 03 00 01 38 c8 5c 7e 95 c0; auto-config enabled (IP, subnet, router). Registering IP Stack5 driver Tcpip NI: Init - RegisteredStackCount = 5 -> End IP Stack interfaces USB host subsytem intilialized Successfully mapped HCD interrupt 12 Registered BRCM USB HCD with USB Host subytem ^^^ Interface creation and driver startup complete ^^^ Creating BcmRgRemoteAccessCommandTable Forward Assist Manager Starting... Creating a new host FAP DQM manager. Instance: 82c49f50 Creating the CableHome Forwarder... Adding Eth-Switch Lan(1) HalIf to the CableHome Forwarder Adding Eth-Switch Lan(2) HalIf to the CableHome Forwarder Adding Eth-Switch Lan(3) HalIf to the CableHome Forwarder Adding Eth-Switch Lan(4) HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(0) Primary HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(1) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(2) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(3) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(4) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(5) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(6) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(7) MBSS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(8) WDS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(9) WDS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(10) WDS HalIf to the CableHome Forwarder Adding 802.11 RF (WiFi)(0)(11) WDS HalIf to the CableHome Forwarder Adding IP Stack3 HalIf to the CableHome Forwarder Adding IP Stack4 HalIf to the CableHome Forwarder Adding IP Stack5 HalIf to the CableHome Forwarder Creating the DOCSIS Forwarder... Adding DOCSIS CableModem HalIf as the default interface to the DOCSIS Forwarder Adding IP Stack1 HalIf to the DOCSIS Forwarder Adding IP Stack2 HalIf to the DOCSIS Forwarder Adding WAN-Man Interface HalIf as the default interface to the CableHome Forwarder Adding eRouter Embedded Interface HalIf to the DOCSIS Forwarder [00:00:15 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::InstallMiniUsfs: (BFC System) Installing Mini-Usfs snoop Isolating CM IP stack from eRouter Embedded Interface Current IP address is default 0.0.0.0. [00:00:15 01/01/1970] [tStartup] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack2 HalIf) Configuring IP stack 2: IP Address = 192.168.100.1 (primary IP address) Subnet Mask = 255.255.255.0 Router = 192.168.100.254 IsPrimaryInterface = 0 SES2WindowClosed! (unexpected) [00:00:16 01/01/1970] [tStartup] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack2 HalIf) Configuring link-local IPv6 address fe80::209:5bff:feed:da02/64 Creating Propane Control Thread... Propane version: 2.0.1 (28 Oct 2002) Instantiating CmSnmpAgent object. Starting SNMP subsystem Registering STP Filter Snoop with all interfaces. Registering DOCSIS MIB Filter Snoop with CPE and WAN interfaces. Creating SNMP agent CPE diag agent CPE diag agent disabling management. CPE diag agent defering traps. [00:00:16 01/01/1970] [tStartup] CwmpClientNonVolSettings::WriteToImpl: Wrote Impl Allowed List size 0 BcmSnmpThread starting thread operation. Initializing Net-SNMP transport for IPv4 Initializing Net-SNMP transport for IPv6 IPv6 - register netsnmp_brcmV6_ctor to get our brcm V6 UDP domain IPv6 init_bcmV2SessionAndTransport: Open a session and hook our callbacks [00:00:18 01/01/1970] [tStartup] BcmDocsisCmHalIf::RegisterSnmpObjects: (DOCSIS CableModem HalIf) Interface 10 additional registration w/ SNMP agent OK. [00:00:18 01/01/1970] [tStartup] BcmErouterPacketSwitchBridgingHalIf::RegisterSnmpObjects: (eRouter Embedded Interface HalIf) Interface 39 additional registration w/ SNMP agent OK. Setting US cal singleton instance to 0 WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.1.6 on Vendor CM Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.1429.79.2.1.6 to agent Vendor CM Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.1.6 on Vendor CM Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.1429.79.2.1.6 to agent Vendor CM Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.1.6 on Vendor CM Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.1429.79.2.1.6 to agent Vendor CM Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.1429.79.2.1.6 on Vendor CM Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.1429.79.2.1.6 to agent Vendor CM Agent w/ BRCM Factory Support ===> Object not found on agent. CmSnmpAgent installing views... Vendor CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted Vendor CM Agent w/ BRCM Factory Support IpStackEvent Vendor CM Agent w/ BRCM Factory Support installing engine ID... Vendor CM Agent w/ BRCM Factory Support installing context... SNMP startup complete. [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - SA Monitor Snoop: unsafe modification of the Snoop lists after the interface is up! [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - SA DNS Snoop: unsafe modification of the Snoop lists after the interface is up! [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! Added WPA-NAS snoop to 802.11 interface. WARNING: BcmWpaNasThread using hardcoded WIFI core instance - FIXME. *************** Instantiating DOCSIS CWMP Client object. [00:00:20 01/01/1970] [tStartup] CwmpClient::CwmpClient: ****** Constructor called ****** [00:00:20 01/01/1970] [tStartup] CwmpClient::CwmpClient: INFO - Setting up the singleton pointer. [00:00:20 01/01/1970] [tStartup] CwmpClient::Setup: entered GetSingletonInstance: Created DHCP server thread GetSingletonInstance: Created Routed Subnet Table GetSingletonInstance: Created RIP Client Thread *** FWSTATE: kFwStateFwActive *** Firewall: WAN HalIf is eRouter Embedded Interface(70736231) [00:00:20 01/01/1970] [tStartup] BcmCableHomeIpStackHelper::CreateLease: DHCP lease already exists, releasing lease clientId = htype=1, value=38:c8:5c:7e:95:c1 Current IP address is default 0.0.0.0. [00:00:20 01/01/1970] [CableHomeCtlThread] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack4 HalIf) Configuring IP stack 4: IP Address = 192.168.100.5 (primary IP address) Subnet Mask = 255.255.255.0 Router = 192.168.100.254 IsPrimaryInterface = 0 [00:00:20 01/01/1970] [FTP Lite Client Thread for IP Stack1] FtpLiteClientThread::ThreadMain: (FTP Lite Client Thread for IP Stack1) Broadcom FTP Lite Client thread starting... Vendor CM Event Log initializing with stored events. Event log initialization complete. Creating the firewall thread, now that it is safe... Current IP address is default 0.0.0.0. [00:00:21 01/01/1970] [tStartup] BcmEcosIpHalIf::ConfigureLeaseImpl: (IP Stack5 HalIf) Configuring IP stack 5: IP Address = 192.168.1.1 (primary IP address) Subnet Mask = 255.255.255.0 Router = 192.168.1.254 IsPrimaryInterface = 0 [00:00:22 01/01/1970] [tStartup] BcmEpsCmDocsisApplication::InitializeLanInterface: (EPS-CM DOCSIS Application) Binding 192.168.1.1 ip address to interface. [00:00:22 01/01/1970] [tStartup] BcmeRouterDhcpv6IpHelper::CreateLease: Creating DHCP lease for client id = htype=1, value=38:c8:5c:7e:95:c1 [00:00:22 01/01/1970] [tStartup] BcmContentFilterSnoop::BcmContentFilterSnoop: (Http Content Filter Snoop) WARNING - Singleton pointer is not NULL! There are multiple instances! Leaving the singleton pointer alone... Creating SNMP agent CH agent CH agent disabling management. CH agent defering traps. Instantiating eRouter SnmpAgent object. ===> WARNING: Can't add saRgDot11MgmtBaseGroup @ 0x82980b9c to iso, group already exists. Registering wln0 Registering wln1 Registering wln2 Registering wln3 Registering wln4 Registering wln5 Registering wln6 Registering wln7 ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.2 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.5 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.1.1.6.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.1.1.6.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.1.1.6.2.2 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.1.1.6.2.2 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.4 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.3.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.6.3.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.1.1.6.3.2 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.2.5.4.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. Registering wln0 Registering wln1 Registering wln2 Registering wln3 Registering wln4 Registering wln5 Registering wln6 Registering wln7 ===> WARNING: Failed to register ScalarMibBridge 1.3.6.1.4.1.1429.79.2.3.7 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4413.2.99.1.1.2.1.5 to agent Vendor CM Agent w/ BRCM Factory Support ===> Entry 3 already exists. CHSnmpAgent installing views... Vendor CH Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted Vendor CH Agent w/ BRCM Factory Support IpStackEvent Vendor CH Agent w/ BRCM Factory Support installing engine ID... Vendor CH Agent w/ BRCM Factory Support installing context... Vendor CM Agent w/ BRCM Factory Support setting master agent to Vendor CH Agent w/ BRCM Factory Support Creating SNMP agent CH diag agent CH diag agent disabling management. CH diag agent defering traps. CH diag agent setting V1/V2 view to unrestricted CH diag agent IpStackEvent CH diag agent enabling management. CH diag agent sending deferred traps... Done w/ deferred traps. CH diag agent installing engine ID... CH diag agent installing context... [00:00:26 01/01/1970] [CableHomePingTool Thread] BcmThread::BcmPanasonicSnoop: (Ping Maintenance Thread) WARNING - Singleton pointer is not NULL! There are multiple BcmParentalCtlThread devices! Leaving the singleton pointer alone... [[00:00:26 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::EnableDhcpServerProvisioning: (CableHomeDhcpServerIpServiceAppIf) Setting DHCP server provisioning to (0) [00:00:26 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::EnableDhcpServerProvisioning: (CableHomeDhcpServerIpServiceAppIf) Setting DHCP server provisioning to (1) WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. WARNING - Couldn't find table 1.3.6.1.4.1.4491.2.4.8.1.2.1 on Vendor CH Agent w/ BRCM Factory Support ===> WARNING: Failed to register TabularMibBridge 1.3.6.1.4.1.4491.2.4.8.1.2.1 to agent Vendor CH Agent w/ BRCM Factory Support ===> Object not found on agent. Registering Qos2 Policy Table Registering Qos2 Traffic Class Table Registering Lan Addr Entry Table Registering Dhcp Server Lease Database 00: 0:26 1/ 1/1970] [DNS Server Thread] BcmDnsServerThread::ThreadMain: (DNS Server Thread) Broadcom V2 DNS Server starting...waiting for events... Vendor CH Event Log w/ BRCM Factory Support initiCreating a new host MSG PROC DQM manager. Instance: 828ca494, DQM_REGS = b8801800, CTRL_REGS = b8801000 alizing with stored events. InitializeNapDqmMessageChannel SUCCESS! hostNapHalIf: InitializeNapDqmMessageChannel SUCCESS! NatTrafficCounterPsmOffset SUCCESS! Counter PSM Offset is 14368 DMA replace PSM Offset is 5664 DMA checksum PSM Offset is 32 NatpFfeOffsets SUCCESS! FFE HASH0 Bin Offset is 45 FFE DMA REPLACE Offset is 205 NAT Session Manager: PSM start is @ 15810000 (3380) [00:00:27 01/01/1970] [tStartup] BcmRipClientThread::AuthEnable: (Rip Client Thread) Broadcom V2 RIP Client MD5 Authentication status = 1 [00:00:27 01/01/1970] [tStartup] BcmTracerouteThread::BcmTracerouteThread: (Traceroute Thread) WARNING - Singleton pointer is not NULL! There are multiple BcmTracerouteThread devices! Leaving the singleton pointer alone... [00:00:27 01/01/1970] [IkeThread] IkeThread::Initialize: (IkeThread) INFO - Initializing thread objects... [[00:00:27 01/01/1970] [tStartup] IkeThread::BcmVpnNonVolSettings: (IkeThread) INFO - Setting up the singleton pointer. Creating BcmVpnCommandTable Dynamic DNS client DISABLED. [00:00:27 01/01/Creating a new host MSG PROC DQM manager. Instance: 828b834c, DQM_REGS = b8801800, CTRL_REGS = b8801000 Creating a new host MSG PROC DQM manager. Instance: 828b8290, DQM_REGS = b8801800, CTRL_REGS = b8801000 1970] [tStartup] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack5 HalIf) Configuring link-local IPv6 address fe80::3ac8:5cff:fe7e:95c0/64 [0CH diag agent IpStackEvent 00:00:27 01/01/1970] [IkeThread] IkeThread::ThreadMain: (IkeThread) Entering... [00:00:27 01/01/1970] [IkeThread] IkeThread::ThreadMain: (IkeThread) Starting IPSEC/IKE initialization 0: 0:27 1/ 1/1970] [NAT Session Manager Thread] BcmNatSessionManagerThread::ThreadMain: (NAT Session Manager Thread) NAT Session Manager waiting for events... -- Detected (Eth-Switch Lan(1)) Mask: 0x1 as (primary) network -- Detected (Eth-Switch Lan(2)) Mask: 0x2 as (primary) network -- Detected (Eth-Switch Lan(3)) Mask: 0x4 as (primary) network -- Detected (Eth-Switch Lan(4)) Mask: 0x8 as (primary) network -- Detected (802.11 RF (WiFi)(0)(0) Primary) Mask: 0x10 as (primary) network -- Forcing (802.11 RF (WiFi)(0)(1) MBSS) Mask: 0x20 (non-primary) Prefix Offset: (2) -- Forcing (802.11 RF (WiFi)(0)(2) MBSS) Mask: 0x40 (non-primary) Prefix Offset: (3) -- Forcing (802.11 RF (WiFi)(0)(3) MBSS) Mask: 0x80 (non-primary) Prefix Offset: (4) -- Forcing (802.11 RF (WiFi)(0)(4) MBSS) Mask: 0x100 (non-primary) Prefix Offset: (5) -- Forcing (802.11 RF (WiFi)(0)(5) MBSS) Mask: 0x200 (non-primary) Prefix Offset: (6) -- Forcing (802.11 RF (WiFi)(0)(6) MBSS) Mask: 0x400 (non-primary) Prefix Offset: (7) -- Forcing (802.11 RF (WiFi)(0)(7) MBSS) Mask: 0x800 (non-primary) Prefix Offset: (8) [00:00:27 01/01/1970] [tStartup] BcmRgHttpServerThread::Enable: (HttpServerThread) Broadcom HttpServerThread running status = 1 Residential Gateway HNAP mode enable = 0 ********************************************************** Running as a Residental Gateway Enabled device! ********************************************************** *********************************************** (DHCP) WAN IP Connection Configuration *********************************************** [00:00:28 01/01/1970] [tStartup] BcmSled::GlobalEnable: (Singleton Instance) WARNING - eDOCSIS SLED is being disabled. Enabled HCD interrupt 12 +++ Starting LpdThread +++ Checking board manufacturing state... Board appears to be manufactured OK. EUsb Print Server - Bound to CM IP Address = [ 192.168.100.1 ] to listen for print requests. vent log initialization complete. Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted Vendor CPE Agent w/ BRCM Factory Support IpStackEvent Vendor CPE Agent w/ BRCM Factory Support enabling management. Vendor CPE Agent w/ BRCM Factory Support sending deferred traps... Done w/ deferred traps. Vendor CPE Agent w/ BRCM Factory Support installing engine ID... Vendor CPE Agent w/ BRCM Factory Support installing context... Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView acsd_main: Thread creation ok acsd_main: Thread start ok [00:00:29 01/01/1970] [tStartup] CwmpClient::Start: CWMP Client starting [00:00:29 01/01/1970] [tStartup] CwmpClient::CreateThread: Starting CWMP Client thread... [00:00:29 01/01/1970] [tStartup] CwmpClientThread::CwmpClientThread: CWMP Client thread constructor [00:00:29 01/01/1970] [tStartup] CwmpClientThreadACT::CwmpClientThreadACT: constructor [00:00:29 01/01/1970] [tStartup] CwmpIpStackEventACT::CwmpIpStackEventACT: constructor [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: ++++++++++++ Setting up message queue and event set [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: ++++++++++++ calling evcpe_setup... [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - Entered for setup [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - grabbed my class tree [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - Object created and initted [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - repo created and initted [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::libevent: WARNING - select_init: calloc @ 0x8280d898 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::EvutilHelper: INFO - constructor [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: listener bound to 127.0.0.1:1024 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: accepted connection from 127.0.0.1:1024 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: returning sockets 26 and 27 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: returning sockets 27 and 26 [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::libevent: WARNING - evsig_init: Got socket fds 27 and 26 [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - returned from event_init() [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_repo_nonvolatile_restore: INFO - NVRAM restored, transfer list size 0 [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - returned from evcpe_repo_nonvolatile_restore() [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: listener bound to 127.0.0.1:1026 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: accepted connection from 127.0.0.1:1026 [00:00:29 01/01/1970] [CWMP Client Thread] EvutilHelper::Socketpair: returning sockets 28 and 29 [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - returned from events_init_with_base() [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClient::evcpe_setup: INFO - returning rc=0 [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: ++++++++++++ Creating Data Model objects [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: >>> CreateChildren [00:00:29 01/01/1970] [CWMP Client Thread] SystemListObjectCwmpBridge::SystemListObjectCwmpBridge: INFO - SystemListObjectCwmpBridge constructor [00:00:29 01/01/1970] [CWMP Client Thread] SystemListObjectCwmpBridge::SystemListObjectCwmpBridge: INFO - Setting up the singleton pointer. [00:00:29 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: >>> CreateObjects [00:00:29 01/01/1970] [CWMP Client Thread] SystemListObjectCwmpBridge::CreateObjects: INFO - Entered, parent .UserInterface. [00:00:29 01/01/1970] [CWMP Client Thread] SystemListObjectCwmpBridge::CreateObjects: INFO - New Path .UserInterface.X_CLEARACCESS_COM_SystemList. [00:00:29 01/01/1970] [CWMP Client Thread] SystemListObjectCwmpBridge::UpdateCache: INFO - Entered [00:00:30 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: >>> Initialize [00:00:30 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: ++++++++++++ Subscribing to other events [00:00:30 01/01/1970] [CWMP Client Thread] CwmpClientThread::Initialize: ++++++++++++ Subscribing to CABLEHOME cntl thread events [00:00:30 01/01/1970] [tStartup] CwmpClient::CreateThread: Starting Content Filter thread... [00:00:30 01/01/1970] [Content Filter Thread] CntFltThread::Initialize: Creating PBCA Snoop [00:00:30 01/01/1970] [Content Filter Thread] PbcaSnoop::PbcaSnoop: (PBCA CntFlt Snoop) INFO - Content Filter Snoop constructor [00:00:30 01/01/1970] [Content Filter Thread] PbcaSnoop::PbcaSnoop: (PBCA CntFlt Snoop) INFO - Content Filter Snoop complete [00:00:30 01/01/1970] [Content Filter Thread] CntFltThread::Initialize: Installing Snoop using CableHome Forwarder dflt i/f WAN-Man Interface [00:00:30 01/01/1970] [tStartup] CwmpClient::CreateThread: Starting Time Blocking thread... [00:00:30 01/01/1970] [Time Blocking Thread] TmBlkThread::Initialize: PBCA Snoop exists [[00:00:30 01/01/1970] [tStartup] CwmpClient::CreateThread: Starting Captive Portal thread... [00:00:30 01/01/1970] [Captive Portal Thread] CaptPortThread::Initialize: PBCA Snoop exists [[[00:00:30 01/01/1970] [tStartup] CwmpClient::CreateThread: Starting Bandwidth Monitor thread... [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for eth0 (Eth-Switch Lan(1)) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for eth1 (Eth-Switch Lan(2)) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for eth2 (Eth-Switch Lan(3)) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for eth3 (Eth-Switch Lan(4)) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln0 (802.11 RF (WiFi)(0)(0) Primary) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln1 (802.11 RF (WiFi)(0)(1) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln2 (802.11 RF (WiFi)(0)(2) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln3 (802.11 RF (WiFi)(0)(3) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln4 (802.11 RF (WiFi)(0)(4) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln5 (802.11 RF (WiFi)(0)(5) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln6 (802.11 RF (WiFi)(0)(6) MBSS) [00:00:30 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wln7 (802.11 RF (WiFi)(0)(7) MBSS) [00:00:31 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::Initialize: Installing Snoop for wan0 (WAN-Man Interface) 0[0[00:00:31 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::ArpServerLeasePool: (CableHomeDhcpServerIpServiceAppIf) Arping Dhcp Server Lease pool to populate Usfs table: (192.168.1.10) --> (192.168.1.128) +-----------------------------------------------------------------------+ | Portions of this product contain open source software and are subject | | to terms of the applicable license as specified in the release notes. | +-----------------------------------------------------------------------+ Cisco Gateway +-------------------------------------------------------------------+ | | | ** ** | | ** ** | | ** ** ** ** ** ** | | ** ** ** ** ** ** | | ** ** ** ** ** ** ** ** ** | | ** ** ** ** ** ** ** ** ** | | ** ** ** ** ** ** ** ** ** | | ** ** | | | | | | ****** ** ******* ****** ***** | | ******** ** ******** ******** ******* | | ** ** ** ** ** ** | | ** ** ****** ** ** ** | | ** ** ***** ** ** ** | | ** ** ** ** ** ** | | ******** ** ******** ******** ******* | | ****** ** ******* ****** ***** TM | | | | | | Copyright (c) 1999 - 2011 Cisco Systems, Inc. | | Portions are Copyright (c) 1999 - 2011 Broadcom Corporation | | CxC ( vN/A ) | | CM ( v5.5.5.mp8 ) | | CWMP ( v1.3.23 ) | | | | Revision: ( epc3825-v302r125553-120713c-ONO ) | +-------------------------------------------------------------------+ This software contains software that is part of eCos, the Embedded Configurable Operating System. Copyright c 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 Free Software Foundation, Inc. eCos is free software; you can redistribute it and/or modify it under a modified version of the GNU General Public License as published by the Free Software Foundation. See the eCos License Overview located at http://ecos.sourceware.org/license-overview.html or the link to the GNU General Public License located at such URL for more details. eCos is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Running the system... Beginning Cable Modem operation... Beginning Parental Control operation... Beginning eRouter operation... 00: 0:31 1/ 1/1970] [Time Blocking Thread] TmBlkThread::ThreadMain: Time Blocking pre-loading db... [00:00:31 01/01/1970] [Time Blocking Thread] TmBlkThread::ProcessNonVolSettingsChange: Updating thread [00:00:31 01/01/1970] [Time Blocking Thread] TmBlkThread::ProcessNonVolSettingsChange: Updating hosts [00:00:31 01/01/1970] [Time Blocking Thread] TmBlkThread::ProcessNonVolSettingsChange: Updating Default Windows [00:00:31 01/01/1970] [Time Blocking Thread] TmBlkThread::ThreadMain: Starting periodic timer... [00:00:31 01/01/1970] [Time Blocking Thread] TmBlkThread::ThreadMain: Time Blocking waiting for events... [00:00:31 01/01/1970] [HttpServerThread] BcmRgHttpServerThread::ThreadMain: (HttpServerThread) Recv'd event to resynchronize sockets! [00:00:31 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::ThreadMain: Bandwidth Monitor pre-loading db... [00:00:31 01/01/1970] [Bandwidth Monitor Thread] BwMonThread::ThreadMain: Bandwidth Monitor waiting for events... 0: 0:31 1/ 1/1970] [Content Filter Thread] CntFltThread::ThreadMain: Content Filter pre-loading db... [00:00:31 01/01/1970] [Content Filter Thread] CntFltThread::ThreadMain: Starting periodic timer... [00:00:31 01/01/1970] [Content Filter Thread] CntFltThread::ThreadMain: Content Filter waiting for events... 00: 0:31 1/ 1/1970] [Captive Portal Thread] CaptPortThread::ThreadMain: Captive Portal pre-loading db... [00:00:31 01/01/1970] [Captive Portal Thread] CaptPortThread::ThreadMain: Captive Portal waiting for events... [00:00:31 01/01/1970] [Scan Downstream Thread] BcmSACmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel... Resetting EnergyDetected to false. Forgetting energy frequency. ============================================================== Try LKF first. ============================================================== 331000000 Hz... Type 'help' or '?' for a list of commands... CM> [00:00:31 01/01/1970] [CableHomePingTool Thread] CableHomePingTool::ArpIpAddressRange: (CableHomePingTool Thread) ARP'ing of Ip Address Range (192.168.1.10) --> (192.168.1.128) ============================================================== Finish scanning LKF. ============================================================== ============================================================== Try PUF Table first. ============================================================== 474000000 Hz... 482000000 Hz... 490000000 Hz... 498000000 Hz... 506000000 Hz... CM> CM> 514000000 Hz... 522000000 Hz... 530000000 Hz... 466000000 Hz...