User Tools

Site Tools


zo0ok 20150412: This device has obviously booted OpenWRT at least once. But the target=mpc8241 is not available in trunk. It used to say supported=10.03 in ToH. I also did not find any images in mpc* or ppc* that seemed suitable. So I have deleted the supported/target columns from the ToH. If this device works and is not abandoned by OpenWRT, please update this article!

CEEDTec WW721 (MPC8241-M3-EP)

System Bootup

U-Boot 1.3.4 (Aug 10 2009 - 17:59:33)

CPU:   MPC8245 Revision 1.4 at 192 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Sandpoint 8245 Unity ##Test not implemented yet##
DRAM:  32 MB
In:    serial
Out:   serial
Err:   serial
Net:   RTL8139#0
Hit any key to stop autoboot:  0 
## Booting kernel from Legacy Image at ff810000 ...
   Image Name:   Linux-
   Created:      2010-10-27   9:47:39 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1317676 Bytes =  1.3 MB
   Load Address: 00400000
   Entry Point:  00400628
   Uncompressing Kernel Image ... OK
Memory <- <0x0 0x2000000> (32MB)
CPU clock-frequency <- 0xb71b000 (192MHz)
CPU timebase-frequency <- 0xf42400 (16MHz)
CPU bus-frequency <- 0x3d09000 (64MHz)

zImage starting: loaded at 0x00400000 (sp: 0x01f419c0)
Allocating 0x2dac20 bytes for kernel ...
gunzipping (0x00000000 <- 0x0040d000:0x006c8a60)...done 0x2ab3a0 bytes

Linux/PowerPC load: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=squashfs,jffs2 init=/etc/preinit
Finalizing device tree... flat tree at 0x6d5300
Using WIWI machine description
Linux version (sandp@coyote) (gcc version 4.4.3 (GCC) ) #3 Wed Oct 27 17:47:30 MYT 2010
bootconsole [udbg0] enabled
Adding PCI host bridge /pci@fec00000
PCI host bridge /pci@fec00000 (primary) ranges:
  IO 0x00000000fe000000..0x00000000febfffff -> 0x0000000000000000
 MEM 0x0000000080000000..0x00000000efffffff -> 0x0000000080000000 
Zone PFN ranges:
  DMA      0x00000000 -> 0x00002000
  Normal   0x00002000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=squashfs,jffs2 init=/etc/preinit
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29532k/32768k available (2576k kernel code, 3236k reserved, 160k data, 187k bss, 124k init)
Kernel virtual memory layout:
  * 0xffffe000..0xfffff000  : fixmap
  * 0xfd3fc000..0xfe000000  : early ioremap
  * 0xc3000000..0xfd3fc000  : vmalloc & ioremap
Hierarchical RCU implementation.
mpic: Setting up MPIC " EPIC     " version 1.2 at fc040000, max 1 CPUs
mpic: ISU size: 26, shift: 5, mask: 1f
mpic: Initializing for 26 sources
clocksource: timebase mult[fa00000] shift[22] registered
Console: colour dummy device 80x25
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
pci 0000:00:0b.0: PME# supported from D1 D2 D3hot
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0c.0: PME# supported from D1 D3hot D3cold
pci 0000:00:0c.0: PME# disabled
pci 0000:00:0c.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0c.2: PME# disabled
PCI: Cannot allocate resource region 0 of device 0000:00:0c.2, will remap
PCI: Cannot allocate resource region 0 of device 0000:00:0b.0, will remap
bio: create slab <bio-0> at 0
vgaarb: loaded
Switching to clocksource timebase
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xfc004500 (irq = 0) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0xfc004600 (irq = 0) is a 16550A
brd: module loaded
loop: module loaded
wiwi flash device: 800000 at ff800000
MPC8241 Flash: Found 1 x16 devices at 0x0 in 8-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 5 MTD partitions on "MPC8241 Flash":
0x000000000000-0x000000010000 : "rsvd"
0x000000010000-0x000000180000 : "kernel"
0x000000180000-0x000000700000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=450000, len=2B0000 
0x000000450000-0x000000700000 : "rootfs_data"
0x000000700000-0x000000740000 : "u-boot"
0x000000740000-0x000000800000 : "data"
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:00:0b.0: enabling device (0006 -> 0007)
eth0: RTL-8139C+ at 0xc3074000, 00:25:e0:00:02:28, IRQ 16
mice: PS/2 mouse device common for all mice
nf_conntrack version 0.5.0 (461 buckets, 1844 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 124k init
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Compat-wireless backport release: compat-wireless-2010-07-13-4-g04898a5
Backport based on wireless-2.6.git v2.6.35-rc6-48432-gdce358e
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ath5k 0000:00:0d.0: enabling device (0000 -> 0002)
ath5k 0000:00:0d.0: registered as 'phy0'
Registered led device: ath5k-phy0::rx
Registered led device: ath5k-phy0::tx
ath5k phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45)
cfg80211: Calling CRDA for country: AM
cfg80211: Regulatory domain changed to country: AM
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 1800 mBm)
    (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 1800 mBm)
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <>
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwis.
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:0c.2: EHCI Host Controller
ehci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0c.2: Enabling legacy PCI PM
ehci_hcd 0000:00:0c.2: irq 17, io mem 0x80000100
ehci_hcd 0000:00:0c.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux ehci_hcd
usb usb1: SerialNumber: 0000:00:0c.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0c.0: OHCI Host Controller
ohci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0c.0: irq 17, io mem 0x81000000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux ohci_hcd
usb usb2: SerialNumber: 0000:00:0c.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
JFFS2 notice: (1146) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, .
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay

BusyBox v1.15.3 (2010-10-27 12:18:21 MYT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 Backfire (10.03, r22498) --------------------------
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua 
  * 1/3 shot Bailey's  on the bottom, then Bailey's, 
  * 1/3 shot Vodka     then Vodka.
root@OpenWrt:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00800000 00010000 "MPC8241 Flash"
mtd1: 00010000 00002000 "rsvd"
mtd2: 00170000 00010000 "kernel"
mtd3: 00580000 00010000 "rootfs"
mtd4: 002b0000 00010000 "rootfs_data"
mtd5: 00040000 00010000 "u-boot"
mtd6: 000c0000 00010000 "data"
CTRL-A Z for help |115200 8N1 | NOR | Minicom 2.3    | VT102 |      Offline                                   
toh/ceedtec/ww721.txt · Last modified: 2015/04/12 09:19 by zo0ok