Differences
This shows you the differences between two versions of the page.
| Next revisionBoth sides next revision | |||
| toh:buffalo:wzr-ag300nh [2015/10/17 08:18] – Link to media adjusted tmomas | toh:buffalo:wzr-ag300nh [2015/12/14 10:38] – New bootlog formatting applied tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Buffalo WZR-AG300NH ====== | ||
| + | This router is pretty similar compared to [[toh: | ||
| + | ===== OpenWrt support ===== | ||
| + | Currently there is **no support for OpenWrt** on this router; initial porting efforts are in progress. | ||
| + | |||
| + | ===== Hardware ===== | ||
| + | ==== Info ==== | ||
| + | * SoC: Marvell 88F5181 = " | ||
| + | * CPU: ARM926EJ @ 500MHz | ||
| + | * 8-Port Gigabit Ethernet Switch: Marvell 88E6131 | ||
| + | * Two gigabit transceivers: | ||
| + | * Two MAC/ | ||
| + | * Two 2.4 / 5 GHz RF transceiver chips: Marvell 88W8060 | ||
| + | * Flash: 8MB (Samsung K8D6316UBM-PI07) | ||
| + | * RAM: 32MB (DDR SDRAM - ProMOS V58C2128164SBI5 x 2) | ||
| + | |||
| + | |||
| + | ==== Serial console ==== | ||
| + | There is a 4-pin serial console header on the mainboard (next to the ProMOS RAM chip). The serial console gives you full access to the bootloader and a root shell once the factory firmware is booted. | ||
| + | |||
| + | | **Pin 1** | Vcc +3.3V | | ||
| + | | **Pin 2** | Gnd | | ||
| + | | **Pin 3** | Tx | | ||
| + | | **Pin 4** | Rx | | ||
| + | | Settings | ||
| + | |||
| + | {{: | ||
| + | |||
| + | |||
| + | ==== Boot Log ==== | ||
| + | <WRAP bootlog> | ||
| + | < | ||
| + | # umount: ramfs busy - remounted read-only | ||
| + | umount: none busy - remounted read-only | ||
| + | The system is going down NOW !! | ||
| + | Sending SIGTERM to all processes. | ||
| + | Jan 1 00:02:00 2008 (none) syslog.info System log daemon exiting. | ||
| + | SendZPlease stand by while rebooting the system. | ||
| + | Restarting system. | ||
| + | Resetting! | ||
| + | |||
| + | | ||
| + | | \/ | __ _ _ ____ | ||
| + | | |\/| |/ _` | '__\ \ / / _ \ | | | ||
| + | | | | | (_| | | \ V / __/ | | | ||
| + | |_| |_|\__, | ||
| + | | ||
| + | | | | | | __ ) ___ ___ | |_ | ||
| + | | | | |___| _ \ / _ \ / _ \| __| | ||
| + | | |_| |___| |_) | (_) | (_) | |_ | ||
| + | | ||
| + | ** MARVELL BOARD: RD-88F5181L-VOIP-GE LE | ||
| + | |||
| + | U-Boot 1.1.1 for BUFFALO AIRSTATION (Mar 22 2007 - 09:22:20) Marvell version: 1.10.8 | ||
| + | |||
| + | # Buffalo Version: 1.09 | ||
| + | |||
| + | DRAM CS[0] base 0x00000000 | ||
| + | DRAM Total size 32MB | ||
| + | Memory Test start(00000000) end(02000000) size(02000000) | ||
| + | Pattern 55555555 | ||
| + | Memory Test OK | ||
| + | Unknown Vendor 0xecUnknown Chip Type id 0x22e2 | ||
| + | Size: 8 MB,Bus Width: 2, device Width: 2. | ||
| + | Flash base: 0xff800000, | ||
| + | Sector Start Addresses: | ||
| + | 00000000 | ||
| + | 0000a000 | ||
| + | 00030000 | ||
| + | 00080000 | ||
| + | 000d0000 | ||
| + | 00120000 | ||
| + | 00170000 | ||
| + | 001c0000 | ||
| + | 00210000 | ||
| + | 00260000 | ||
| + | 002b0000 | ||
| + | 00300000 | ||
| + | 00350000 | ||
| + | 003a0000 | ||
| + | 003f0000 | ||
| + | 00440000 | ||
| + | 00490000 | ||
| + | 004e0000 | ||
| + | 00530000 | ||
| + | 00580000 | ||
| + | 005d0000 | ||
| + | 00620000 | ||
| + | 00670000 | ||
| + | 006c0000 | ||
| + | 00710000 | ||
| + | 00760000 | ||
| + | 007b0000 | ||
| + | [8192kB@ff800000] Flash: | ||
| + | Addresses 20M - 0M are saved for the U-Boot usage. | ||
| + | Mem malloc Initialization (20M - 16M): Done | ||
| + | ### buf_ver=[1.09] U-Boot Ver.=[1.09] | ||
| + | ### build_date(env)=[Mar 22 2007 - 09:22:20] build_date(bin)=[Mar 22 2007 - 09:22:20] | ||
| + | |||
| + | Soc: 88F5181 B1 | ||
| + | CPU: ARM926 (Rev 0) running @ 500Mhz | ||
| + | Orion 1 streaming disabled | ||
| + | SysClock = 166Mhz , TClock = 166Mhz | ||
| + | |||
| + | |||
| + | USB 0: host mode | ||
| + | PCI 0: PCI Express Root Complex Interface | ||
| + | PCI 1: Conventional PCI, speed = 33000000 | ||
| + | Net: | ||
| + | Hit any key to stop autoboot: | ||
| + | |||
| + | tftp server(receive) go, waiting: | ||
| + | Load address: 0x400000 | ||
| + | |||
| + | TftpServer Timeout; | ||
| + | no file was loaded. | ||
| + | ### CRAMFS loading ' | ||
| + | ### CRAMFS load complete: 1024112 bytes loaded to 0x400000 | ||
| + | ## Booting image at 00400000 ... | ||
| + | Image Name: | ||
| + | Image Type: ARM Linux Kernel Image (uncompressed) | ||
| + | Data Size: 1024048 Bytes = 1000 kB | ||
| + | Load Address: 00008000 | ||
| + | Entry Point: | ||
| + | | ||
| + | OK | ||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | Uncompressing Linux...................................................................... done, booting the kernel. | ||
| + | ZLinux version 2.4.27-vrs1 (vc03021@mkitec-xen) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-1)) #1 Thu Jan 10 20:23:58 JST 2008 | ||
| + | CPU: ARM926EJ-Sid(wb) revision 0 | ||
| + | Machine: MV-88fxx81 | ||
| + | Using UBoot passing parameters structure | ||
| + | Sys Clk = 166666667, Tclk = 166666667 | ||
| + | |||
| + | |||
| + | - Warning - This LSP release was tested only with U-Boot release 1.10.16 | ||
| + | |||
| + | On node 0 totalpages: 8192 | ||
| + | zone(0): 8192 pages. | ||
| + | zone(1): 0 pages. | ||
| + | zone(2): 0 pages. | ||
| + | Kernel command line: console=ttyS0, | ||
| + | Calibrating delay loop... 332.59 BogoMIPS | ||
| + | Memory: 32MB 0MB 0MB 0MB = 32MB total | ||
| + | Memory: 30040KB available (1915K code, 341K data, 76K init) | ||
| + | Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) | ||
| + | Inode cache hash table entries: 2048 (order: 2, 16384 bytes) | ||
| + | Mount cache hash table entries: 512 (order: 0, 4096 bytes) | ||
| + | Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) | ||
| + | Page-cache hash table entries: 8192 (order: 3, 32768 bytes) | ||
| + | CPU: Testing write buffer: pass | ||
| + | POSIX conformance testing by UNIFIX | ||
| + | init hw started. | ||
| + | |||
| + | CPU Interface | ||
| + | ------------- | ||
| + | SDRAM_CS0 ....base 00000000, size 32MB | ||
| + | SDRAM_CS1 ....disable | ||
| + | SDRAM_CS2 ....disable | ||
| + | SDRAM_CS3 ....disable | ||
| + | PEX0_MEM ....base e0000000, size 128MB | ||
| + | PEX0_IO ....base f2000000, size | ||
| + | PCI0_MEM ....base e8000000, size 128MB | ||
| + | PCI0_IO ....base f2100000, size | ||
| + | INTER_REGS ....base f1000000, size | ||
| + | DEVICE_CS0 ....no such | ||
| + | DEVICE_CS1 ....no such | ||
| + | DEVICE_CS2 ....no such | ||
| + | DEV_BOOCS ....base f4000000, size 16MB | ||
| + | Flash bankwidth 2, base f4000000, size 1000000 | ||
| + | PCI: bus0: Fast back to back transfers enabled | ||
| + | HW already initialized. | ||
| + | PCI: bus1: Fast back to back transfers enabled | ||
| + | Linux NET4.0 for Linux 2.4 | ||
| + | Based upon Swansea University Computer Society NET3.039 | ||
| + | Initializing RT netlink socket | ||
| + | |||
| + | Marvell Development Board (LSP Version 1.1.3)-- RD-88F5181L-VOIP-GE | ||
| + | |||
| + | | ||
| + | Starting kswapd | ||
| + | Journalled Block Device driver loaded | ||
| + | devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) | ||
| + | devfs: boot_options: | ||
| + | JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. | ||
| + | mel_initsw: GPIO initialize done.. | ||
| + | BUFFALO SWICH & LED DRIVER ver 1.00 | ||
| + | Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled | ||
| + | ttyS00 at 0xf1012000 (irq = 3) is a 16550A | ||
| + | HDLC line discipline: version $Revision: 3.7 $, maxframe=4096 | ||
| + | N_HDLC line discipline registered. | ||
| + | Marvell Gateway Driver: | ||
| + | Detected RD_88F5181L_VOIP_GE | ||
| + | Using VLAN-tag Mode | ||
| + | L3/L4 Checksum offload enabled | ||
| + | Link status indication mode is on (switch irq=40) | ||
| + | Multi queue support ( rxq0=128 rxq1=64 rxq2=64 rxq3=64 txq0=2000 ) | ||
| + | Using boot network interface configuration | ||
| + | eth0: mac_addr 00: | ||
| + | eth1: mac_addr 00: | ||
| + | init switch layer... my_gateway: SetPhyReg(port=0, | ||
| + | my_gateway: SetPhyReg(port=1, | ||
| + | my_gateway: SetPhyReg(port=2, | ||
| + | my_gateway: SetPhyReg(port=3, | ||
| + | my_gateway: SetPhyReg(port=4, | ||
| + | done | ||
| + | init MAC layer... done | ||
| + | loading network interfaces: eth0 eth1 | ||
| + | PPP generic driver version 2.4.2 | ||
| + | PPP Deflate Compression module registered | ||
| + | PPP BSD Compression module registered | ||
| + | physmap flash device: 1000000 at f4000000 | ||
| + | | ||
| + | number of CFI chips: 1 | ||
| + | cfi_cmdset_0002: | ||
| + | Using physmap partition definition | ||
| + | Creating 4 MTD partitions on " | ||
| + | 0x00000000-0x00780000 : " | ||
| + | 0x00780000-0x007a0000 : " | ||
| + | 0x007a0000-0x007c0000 : " | ||
| + | 0x007c0000-0x00800000 : " | ||
| + | Initializing Cryptographic API | ||
| + | IPv6 v0.8 (usagi-cvs) for NET4.0 | ||
| + | IPv6 over IPv4 tunneling driver | ||
| + | NET4: Linux TCP/IP 1.0 for NET4.0 | ||
| + | IP Protocols: ICMP, UDP, TCP | ||
| + | IP: routing cache hash table of 512 buckets, 4Kbytes | ||
| + | TCP: Hash tables configured (established 2048 bind 4096) | ||
| + | ip_conntrack version 2.1 (256 buckets, 2048 max) - 316 bytes per conntrack | ||
| + | ip_tables: (C) 2000-2002 Netfilter core team | ||
| + | ipt_time loading | ||
| + | NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. | ||
| + | ip6_tables: (C) 2000-2002 Netfilter core team | ||
| + | NET4: Ethernet Bridge 008 for NET4.0 | ||
| + | Fast Floating Point Emulator V0.94M by Peter Teichmann. | ||
| + | VFS: Mounted root (cramfs filesystem). | ||
| + | Mounted devfs on /dev | ||
| + | Freeing init memory: 76K | ||
| + | =ZZZinit started: | ||
| + | ZMidLayer.c(1953) ML_Initialize :***** Please push init button if you want to init_reboot ****** | ||
| + | insmod: / | ||
| + | insmod: ae531x.o: no module by that name found | ||
| + | insmod: / | ||
| + | Using / | ||
| + | Warning: loading ap8x-8363 will taint the kernel: non-GPL license - Proprietary | ||
| + | See http:// | ||
| + | ap0: Marvell AP-8x 802.11n adapter: mem=0xe8000000, | ||
| + | Z | ||
| + | Please press Enter to activate this console. ap1: Marvell AP-8x 802.11n adapter: mem=0xe8020000, | ||
| + | mv_gateway: starting eth1 | ||
| + | mv_gateway: eth1 db1 port-mask=0x8, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: starting eth0 | ||
| + | mv_gateway: eth0 db0 port-mask=0x8, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth0 db0 port-mask=0x28, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | mv_gateway: eth1 db1 port-mask=0x8f, | ||
| + | br_add_if: | ||
| + | br_add_if: | ||
| + | <mapping sub-ioctl htbw to cmd 0x8BE0-19> | ||
| + | <mapping sub-ioctl extsubch to cmd 0x8BE0-21> | ||
| + | <mapping sub-ioctl autochannel to cmd 0x8BE0-26> | ||
| + | <mapping sub-ioctl filter to cmd 0x8BE0-16> | ||
| + | <mapping sub-ioctl htbw to cmd 0x8BE0-19> | ||
| + | <mapping sub-ioctl extsubch to cmd 0x8BE0-21> | ||
| + | <mapping sub-ioctl autochannel to cmd 0x8BE0-26> | ||
| + | <mapping sub-ioctl filter to cmd 0x8BE0-16> | ||
| + | br_add_if: | ||
| + | br_add_if: | ||
| + | </ | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||