Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:buffalo:wli-tx4-ag300n [2018/02/20 21:17] – ↷ Links adapted because of a move operation | toh:buffalo:wli-tx4-ag300n [2019/02/12 21:56] – 432 warning added tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Buffalo WLI-TX4-AG300N ====== | ====== Buffalo WLI-TX4-AG300N ====== | ||
| - | Manuf/ | + | {{section> |
| Dual Band Wireless Ethernet Bridge | Dual Band Wireless Ethernet Bridge | ||
| + | |||
| + | Manuf/ | ||
| + | |||
| + | OEM source code available at: [[http:// | ||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| - | ^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version | + | ---- datatable ---- |
| - | | | + | cols : Brand, |
| + | headers : Brand, | ||
| + | align | ||
| + | filter | ||
| + | ---- | ||
| + | ---- datatable ---- | ||
| + | cols : Unsupported Functions_ | ||
| + | filter | ||
| + | ---- | ||
| - | OEM source code available at: [[http:// | ||
| ===== Hardware Highlights ===== | ===== Hardware Highlights ===== | ||
| - | ^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ Wireless NIC ^ | + | ---- datatable ---- |
| - | | Ralink RT2880@?Mhz | 32MiB | 4MiB | 4 | N | Yes | ? | RT2880/ | + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, |
| - | + | header | |
| - | Manufacturer' | + | align : c, |
| + | filter | ||
| + | ---- | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | | FIXME Need install instruction for this device! | | + | ---- datatable ---- |
| - | | + | cols |
| - | - → [[docs:user-guide: | + | headers |
| - | - → **»»»»here»»»»[[about/ | + | align : c,c,c |
| + | filter | ||
| + | ---- | ||
| + | |||
| + | -> [[docs: | ||
| Firmware: | Firmware: | ||
| Line 47: | Line 65: | ||
| ==== Upgrading OpenWrt ==== | ==== Upgrading OpenWrt ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | ||
| Line 94: | Line 112: | ||
| ==== Failsafe mode ==== | ==== Failsafe mode ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| The Buffalo WLI-TX4-AG300N has two buttons. They are Power and Security. Here, we merely name the buttons, so we can use them in the above Howto: | The Buffalo WLI-TX4-AG300N has two buttons. They are Power and Security. Here, we merely name the buttons, so we can use them in the above Howto: | ||
| Line 110: | Line 128: | ||
| | **Vendor: | | **Vendor: | ||
| | **[[docs: | | **[[docs: | ||
| - | | **[[docs: | + | | **[[docs:techref: |
| - | | **[[docs: | + | | **[[docs:techref: |
| | **Flash size: | | **Flash size: | ||
| | **Flash Chip: | | **Flash Chip: | ||
| Line 117: | Line 135: | ||
| | **RAM Chip: | | **RAM Chip: | ||
| | **Wireless No1: | | **Wireless No1: | ||
| - | | **[[docs: | + | | **[[docs:techref: |
| | **USB: | | **USB: | ||
| - | | **[[docs: | + | | **[[docs:techref: |
| - | | **[[docs: | + | | **[[docs:techref: |
| Line 132: | Line 150: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[docs: | + | -> [[docs:techref: |
| Serial is unpopulated 4-pin header near the reset switch. Pinout is VCC (3.3V, only use to power the RS232 level converter), GND, TX, RX. | Serial is unpopulated 4-pin header near the reset switch. Pinout is VCC (3.3V, only use to power the RS232 level converter), GND, TX, RX. | ||
| Line 141: | Line 159: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[docs: | + | -> [[docs:techref: |
| JTAG may be located adjacent to the serial near reset switch: | JTAG may be located adjacent to the serial near reset switch: | ||
| Line 149: | Line 167: | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| ===== Tags ===== | ===== Tags ===== | ||