| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision |
| toh:bt:homehub_v2a [2022/11/05 22:16] – [Installation] info about hardware bug danitool | toh:bt:homehub_v2a [2024/02/12 13:28] – [Installation] revert Version change bill888 |
|---|
| |
| ===== Supported Versions ===== | ===== Supported Versions ===== |
| ---- datatable ---- | <!-- ToH: { |
| cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | "source": "json", |
| headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data | "dom": "t", |
| align : c,c,c,c,c,c,c | "paging": false, |
| filter : Model=Home Hub 2 | "rotate": true, |
| filter : Versions=Type A | "shownColumns": ["brand", "model", "version", "supportedcurrentrel", "oemdevicehomepageurl", "owrt_forum_topic_url", "deviceid"], |
| ---- | "filterColumns": {"model": "^Home Hub 2$", "version": "^Type A$"} |
| | } --> |
| |
| ---- datatable ---- | <!-- ToH: { |
| cols : Unsupported Functions_unsupporteds | "source": "json", |
| filter : Model=Home Hub 2 | "dom": "t", |
| filter : Versions=Type A | "paging": false, |
| ---- | "shownColumns": ["unsupported_functions"], |
| | "filterColumns": {"model": "^Home Hub 2$", "version": "^Type A$"} |
| | } --> |
| |
| |
| ===== Hardware Highlights ===== | ===== Hardware Highlights ===== |
| ---- datatable ---- | <!-- ToH: { |
| cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_ | "source": "json", |
| header : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB | "dom": "t", |
| align : c,c,c,c,c,c,c,c,c,c,c,c,c | "paging": false, |
| filter : Model=Home Hub 2 | "rotate": true, |
| filter : Versions=Type A | "shownColumns": ["model", "version", "cpu", "cpumhz", "flashmb", "rammb", "wlanhardware", "wlan24ghz", "wlan50ghz", "ethernet100mports", "ethernet1gports", "modem", "usbports"], |
| ---- | "filterColumns": {"model": "^Home Hub 2$", "version": "^Type A$"} |
| | } --> |
| |
| |
| ===== Installation ===== | ===== Installation ===== |
| ---- datatable ---- | <!-- ToH: { |
| cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OEM Stock URL_url | "source": "json", |
| headers : Model, Version, Current Release, Firmware OpenWrt Install & Upgrade, Firmware OEM Stock | "dom": "t", |
| align : c,c,c | "paging": false, |
| filter : Model=Home Hub 2 | "rotate": true, |
| filter : Versions=Type A | "shownColumns": ["model", "version", "supportedcurrentrel", "firmwareopenwrtinstallurl", "firmwareoemstockurl"], |
| ---- | "filterColumns": {"model": "^Home Hub 2$", "version": "^Type A$"} |
| | } --> |
| Old firmwares: | Old firmwares: |
| ^ Version ^ Release date ^ Link ^ kernel ^ Tested ^ | ^ Version ^ Release date ^ Link ^ kernel ^ Tested ^ |
| |
| If the sockets/ports are on the front of the board at the bottom, the unpopulated 2mm pitch serial port header is located near the top of the board to the right (varying slightly between rev1 and rev2). In addition to populating it you need to bridge two absent resistor locations on the front of the board (R105, R106). From the top going downwards, the connections are: | If the sockets/ports are on the front of the board at the bottom, the unpopulated 2mm pitch serial port header is located near the top of the board to the right (varying slightly between rev1 and rev2). In addition to populating it you need to bridge two absent resistor locations on the front of the board (R105, R106). From the top going downwards, the connections are: |
| | <a2s> |
| ^ 3.3v ^ | #-----------------# |
| ^ GND ^ | | VCC GND TX RX | |
| ^ TX ^ | J10| .-. .-. .-. .-. | |
| ^ RX ^ | | '-' '-' '-' '-' | |
| | #-'---------------# |
| | |
| | </a2s> |
| |
| Rev2 close-up: \\ | Rev2 close-up: \\ |