Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:bintec-elmeg:bintec-elmeg_rs353xx [2018/03/04 12:54] – bobafetthotmail | toh:bintec-elmeg:bintec-elmeg_rs353xx [2019/08/26 07:56] – [OpenWrt support] armseb | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ~~NOTOC~~ | ~~NOTOC~~ | ||
| - | /* This template is intended to be used via https://wiki.openwrt.org/ | + | /* This template is intended to be used via https:// |
| | {{page> | | {{page> | ||
| Line 9: | Line 9: | ||
| /*****/ | /*****/ | ||
| - | /* How to add images ========> | + | /* How to add images ========> |
| /*****/ | /*****/ | ||
| Line 17: | Line 17: | ||
| ===== OpenWrt support ===== | ===== OpenWrt support ===== | ||
| - | Work in progress | + | === Actually supported === |
| + | * CPU SMP | ||
| + | * Flash chip | ||
| + | * Network interfaces including switch | ||
| + | * DSL modem | ||
| + | * Wireless | ||
| + | * LEDs and RESET button | ||
| + | * USB port | ||
| + | * I2C bus and RTC chip | ||
| ===== Supporting activities ===== | ===== Supporting activities ===== | ||
| * OpenWrt forum thread: https:// | * OpenWrt forum thread: https:// | ||
| * Pull Request: https:// | * Pull Request: https:// | ||
| + | * Repository with Patches : https:// | ||
| + | This repository also supports the Lantiq Danube based RS230 device ( except the Marvell 88E6161 switch ). | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| Line 55: | Line 65: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| ***/ | ***/ | ||
| Line 61: | Line 71: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ===== Failsafe mode ===== | ===== Failsafe mode ===== | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ***/ | ***/ | ||
| Line 90: | Line 100: | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| Here, we merely name the buttons, so we can use them in the above Howto. | Here, we merely name the buttons, so we can use them in the above Howto. | ||
| Line 110: | Line 120: | ||
| | **Architecture: | | **Architecture: | ||
| | **Vendor: | | **Vendor: | ||
| - | | **Bootloader: | + | | **Bootloader: |
| | **System-On-Chip: | | **System-On-Chip: | ||
| | **CPU/ | | **CPU/ | ||
| Line 158: | Line 168: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| You can use any USB cable (i.e printer cable), and plug into the " | You can use any USB cable (i.e printer cable), and plug into the " | ||
| Line 165: | Line 175: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the JTAG Port of this specific device:\\ | How to connect to the JTAG Port of this specific device:\\ | ||