Bintec-Elmeg RS353xx

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Simple and robust professional router based on Lantiq VR9 architecture.

Bintec Router

Actually supported

  • CPU SMP
  • Flash chip
  • Network interfaces including switch
  • DSL modem
  • Wireless
  • LEDs and RESET button
  • USB port
  • I2C bus and RTC chip

This repository also supports the Lantiq Danube based RS230 device ( except the Marvell 88E6161 switch ).

CPU Ram Flash Network WLAN USB Serial JTag
Lantiq VRX288 v1.2 (PSB 80920 EL) @ 500MHz 128 MiB 32 MiB 5x 10/100/1000 abgn 1x 2.0 Yes Yes
Architecture MIPS
Vendor Bintec-Elmeg
Bootloader Proprietary bootloader called “boot monitor”
System-On-Chip Lantiq VRX288 v1.2 (PSB 80920 EL)
CPU/Speed 500 MHz
Flash-Chip AMD/Spansion S29GL256FLT2I
Flash size 32 MiB
RAM 128 MiB
Wireless Atheros AR9300 Rev:4
Ethernet 10/100/1000 Mbit/s
USB 2x 2.0 (1 external and 1 internal for LTE optional card)
RTC Seiko s35390a on I2C bus
Serial Yes
JTAG Yes

I kept the original bootloader (called BootMonitor). The kernel image is loaded from 0x100c0000 into RAM at addr. 0x2d6a0 by the first bootloader. Then, lzma-loader uncompress the kernel on RAM and starts it.

Part    Offset          Size            Name
mtd0    0x10000000      0x20000         logic_config
mtd1    0x10020000      0x20000         logic_addr
mtd2    0x10040000      0x20000         bootmonitor
mtd3    0x10080000      0x40000         flash_config
mtd4    0x100c0000      0x1F40000       firmware

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Remove the 3 screws in the rear of the router, then lift the top panel to the rear and remove it.

port.serial USB type B using cp210x driver

You can use any USB cable (i.e printer cable), and plug into the “Console” port.

Serial connection parameters
for Bintec-Elmeg RS353xx
115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

### RS353aw (Hardware-Rev. 1.0, Firmware-Rev. 1.1) ### CPU Check ... passed (MIPS 34KEc [MT] @ 500/250.0 MHz) SDRAM Check ................................................................................................................................. passed (128 MByte) FLASH Check passed (32 MByte) ### Selftest passed ### Press <sp> for boot monitor or any other key to boot system Booting Image from Flash ROM Checking image ... OK Writing image to RAM (Release 10.1.9.106) ........................................................................................................................................................................................................................................................................................................................................................................................................................................................ OK (16385316 bytes) Booting BOSS... boss image started at 0x2d6a0 BOSS MIPS kernel v2.0 (RS353aw) Copyright (c) 1996-2015 by bintec elmeg GmbH Version V.10.1 Rev. 9 (Patch 6) IPv6, IPSec from 2016/07/21 00:00:00 The system is coming up. Speed index... 332.80 MIPS Collecting Entropy........................................ Installed modules: Slot: BoardId SerialNo 0: SYS-VRX OK 1: GETH5 OK 3: VDSL OK 6: USB2 OK 7: WLAN-ATH OK InstallModules = 0x5 The system is ready. AUTOEXEC: 1 date Wed Oct 26 20:41:15 2016 done 1 configd SystemId: RN7Fxxxxxxxxxxx Cfg: (default) done 4 dslvrxd background 5 sysconfigd background 5 usbd background 9 comd background 10 isdnd background 11 isdnautocf background 19 ethoad background 19 pppoad background 19 rpoad background 50 brd background 50 ipd background 50 natproxyd background 51 telnetd background 51 alertd background 51 telnetd6 background 51 stfd background 51 snmpd background 52 httpd background 52 syslogd background 68 pppoed background 69 itpd background 69 tud background 70 routed background 70 pppd background 70 radiusd background 70 tacacspd background 70 gremprd background 70 l2tpd background 90 timed background 97 dnsd background 97 alived background 97 scheduled background 97 watchd background 99 vectoringd background 99 authd background 99 supplicantd background 99 vcapid background 99 ddnsd background 99 bootpd background BOOTP: creating ipRouteTableEntry BOOTP: Dest=192.168.0.0 IfIndex=1000000 BOOTP: NextHop=192.168.0.254 Mask=255.255.255.0 99 resolvd background 99 pingd background 99 scfgmgrd background 99 stunneld background 99 serviced background 99 dhcp6d background 99 ipsecd background 99 isdnlogind background 99 sshd background 99 httpproxyd background 99 traced background 99 upnpd background 99 capwapd background 99 caad background 99 wtpd background 99 tr069d background Welcome to RS353aw version V.10.1 Rev. 9 (Patch 6) IPv6, IPSec from 2016/07/21 00:00:00 systemname is rs353aw, location Login:


### RS353aw (Hardware-Rev. 1.0, Firmware-Rev. 1.0) ### CPU Check ... passed (MIPS 34KEc [MT] @ 500/250.0 MHz) SDRAM Check ................................................................................................................................. passed (128 MByte) FLASH Check passed (32 MByte) ### Selftest passed ### Warning: Watchdog disabled Press <sp> for boot monitor or any other key to boot system Booting Image from Flash ROM Checking image ... OK Writing image to RAM (Release 10.1.9.106) .... OK (308888 bytes) Booting BOSS... boss image started at 0x2d6a0 U-Boot 2014.01-openwrt4-gef35f22-dirty (Nov 10 2016 - 23:10:34) rs353aw Board: Bintec RS353aw SoC: Lantiq VRX288 v1.2 CPU: 500 MHz IO: 250 MHz BUS: 250 MHz BOOT: NOR w/o BootROM DRAM: 128 MiB Flash: 32 MiB In: serial Out: serial Err: serial Net: Phy not found PHY reset timed out Phy not found PHY reset timed out ltq-eth Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 10120000 ... Image Name: MIPS OpenWrt Linux-4.4.7 Created: 2016-06-30 5:39:05 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1926415 Bytes = 1.8 MiB Load Address: 80002000 Entry Point: 80002000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 4.4.7 (qa@serveurQA) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r49395) ) #45 SMP PREEMPT Fri Nov 11 18:30:02 UTC 2016 [ 0.000000] SoC: xRX200 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] MIPS: machine is Bintec Elmeg RS353aw [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] PERCPU: Embedded 10 pages/cpu @8110b000 s8352 r8192 d24416 u40960 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0007edf8 [ 0.000000] Readback ErrCtl register=0007edf8 [ 0.000000] Memory: 122452K/131072K available (4352K kernel code, 195K rwdata, 1280K rodata, 1260K init, 226K bss, 8620K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:256 [ 0.000000] Setting up vectored interrupts [ 0.000000] Setting up IPI vectored interrupts [ 0.000000] CPU Clock: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.007881] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088) [ 0.042379] pid_max: default: 32768 minimum: 301 [ 0.047256] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053798] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.093447] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.093464] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.093666] CPU1 revision is: 00019556 (MIPS 34Kc) [ 0.153034] Synchronize counters for CPU 1: done. [ 0.157937] Brought up 2 CPUs [ 0.165466] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.175290] pinctrl core: initialized pinctrl subsystem [ 0.181241] NET: Registered protocol family 16 [ 0.196166] pinctrl-xway 1e100b10.pinmux: Init done [ 0.202236] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [ 0.315977] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [ 0.512783] usbcore: registered new interface driver usbfs [ 0.518373] usbcore: registered new interface driver hub [ 0.523838] usbcore: registered new device driver usb [ 0.529136] Linux video capture interface: v2.00 [ 0.534241] Advanced Linux Sound Architecture Driver Initialized. [ 0.540501] PCI host bridge to bus 0000:00 [ 0.544535] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.551446] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.558412] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.565240] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.573354] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge [ 0.590662] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.597397] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.604660] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.612089] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.619317] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.624382] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.631209] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.638566] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1 [ 0.645164] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned [ 0.651560] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 [ 0.658171] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned [ 0.666343] clocksource: Switched to clocksource MIPS [ 0.674794] NET: Registered protocol family 2 [ 0.680388] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.687351] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.693696] TCP: Hash tables configured (established 1024 bind 1024) [ 0.700253] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.706037] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.712740] NET: Registered protocol family 1 [ 0.717531] gptu: totally 6 16-bit timers/counters [ 0.722512] gptu: misc_register on minor 63 [ 0.726706] gptu: succeeded to request irq 126 [ 0.731195] gptu: succeeded to request irq 127 [ 0.735718] gptu: succeeded to request irq 128 [ 0.740201] gptu: succeeded to request irq 129 [ 0.744746] gptu: succeeded to request irq 130 [ 0.749248] gptu: succeeded to request irq 131 [ 0.756103] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin [ 0.763492] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 79E0000 [ 0.769866] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 79E0000 [ 0.855983] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.882759] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.888572] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.901783] io scheduler noop registered [ 0.905779] io scheduler deadline registered (default) [ 0.912185] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.921133] console [ttyLTQ0] enabled [ 0.921133] console [ttyLTQ0] enabled [ 0.928455] bootconsole [early0] disabled [ 0.928455] bootconsole [early0] disabled [ 0.938528] lantiq nor flash device: 02000000 at 10000000 [ 0.942702] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.952150] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.957260] Amd/Fujitsu Extended Query version 1.3. [ 0.962394] number of CFI chips: 1 [ 0.965698] 8 ofpart partitions found on MTD device ltq_nor [ 0.971256] Creating 8 MTD partitions on "ltq_nor": [ 0.976163] 0x000000000000-0x000000020000 : "logic_config" [ 0.987891] 0x000000020000-0x000000040000 : "logic_addr" [ 0.998029] 0x000000040000-0x000000060000 : "bootmonitor" [ 1.008296] 0x000000080000-0x0000000c0000 : "flash_config" [ 1.018706] 0x0000000c0000-0x000000100000 : "uboot" [ 1.028528] 0x000000100000-0x000000120000 : "uboot-env" [ 1.038674] 0x000000120000-0x000001fe0000 : "firmware" [ 1.068669] 2 uimage-fw partitions found on MTD device firmware [ 1.073229] 0x000000120000-0x0000002f654f : "kernel" [ 1.084418] 0x0000002f654f-0x000001fe0000 : "rootfs" [ 1.094150] mtd: device 8 (rootfs) set to be root filesystem [ 1.098463] 1 squashfs-split partitions found on MTD device rootfs [ 1.104631] 0x0000006a0000-0x000001fe0000 : "rootfs_data" [ 1.116291] 0x000001fe0000-0x000002000000 : "GPHY_CPR" [ 1.210255] libphy: lantiq,xrx200-mdio: probed [ 1.279060] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1) [ 1.347087] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1) [ 1.415071] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1) [ 1.483070] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:02, irq=-1) [ 1.551055] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1) [ 1.559963] i2c /dev entries driver [ 1.562506] wdt 1f8803f0.watchdog: Init done [ 1.569302] usbcore: registered new interface driver snd-usb-audio [ 1.576918] NET: Registered protocol family 10 [ 1.581856] NET: Registered protocol family 17 [ 1.585027] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.597565] 8021q: 802.1Q VLAN Support v1.8 [ 1.606725] hctosys: unable to open rtc device (rtc0) [ 1.610777] ALSA device list: [ 1.613279] No soundc[ 1.617387] UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19 [ 1.626755] VFS: Mounted root (squashfs filesystem) readonly on device 31:8. [ 1.636577] Freeing unused kernel memory: 1260K (805b5000 - 806f0000) [ 2.847719] init: Console is alive [ 2.850036] init: - watchdog - [ 4.562962] eth0: port 4 got link [ 5.005624] Button Hotplug driver version 0.4.1 [ 5.020991] SCSI subsystem initialized [ 5.029716] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.036051] ehci-platform: EHCI generic platform driver [ 5.045348] dwc2 1e101000.ifxhcd: Configuration mismatch. Forcing host mode [ 5.906709] dwc2 1e101000.ifxhcd: DWC OTG Controller [ 5.910290] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1 [ 5.917729] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000 [ 5.923190] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode - [ 5.930598] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode. [ 5.937270] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.943638] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.950833] usb usb1: Product: DWC OTG Controller [ 5.955546] usb usb1: Manufacturer: Linux 4.4.7 dwc2_hsotg [ 5.961019] usb usb1: SerialNumber: 1e101000.ifxhcd [ 5.966970] hub 1-0:1.0: USB hub found [ 5.969691] hub 1-0:1.0: 1 port detected [ 5.974476] dwc2 1e106000.ifxhcd: Configuration mismatch. Forcing host mode [ 6.838690] dwc2 1e106000.ifxhcd: DWC OTG Controller [ 6.842271] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2 [ 6.849654] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000 [ 6.855150] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode - [ 6.862585] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode. [ 6.869255] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.875605] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.882814] usb usb2: Product: DWC OTG Controller [ 6.887526] usb usb2: Manufacturer: Linux 4.4.7 dwc2_hsotg [ 6.893000] usb usb2: SerialNumber: 1e106000.ifxhcd [ 6.898964] hub 2-0:1.0: USB hub found [ 6.901672] hub 2-0:1.0: 1 port detected [ 6.910999] usbcore: registered new interface driver usb-storage [ 6.924463] init: - preinit - [ 7.391760] random: procd urandom read with 112 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.062387] random: nonblocking pool is initialized [ 10.758522] jffs2_scan_eraseblock(): End of filesystem marker found at 0x20000 [ 10.764397] jffs2_build_filesystem(): unlocking the mtd device... done. [ 10.770909] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 120.550498] jffs2: notice: (460) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 120.568042] mount_root: overlay filesystem has not been fully initialized yet [ 120.575794] mount_root: switching to jffs2 overlay - config restore - [ 120.813383] procd: - early - [ 120.815049] procd: - watchdog - [ 121.589522] procd: - ubus - [ 121.644675] procd: - init - Please press Enter to activate this console. [ 122.823289] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH [ 122.836880] NET: Registered protocol family 8 [ 122.839885] NET: Registered protocol family 20 [ 122.869683] PPP generic driver version 2.4.2 [ 122.880892] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 122.907411] Lantiq (VRX) DSL CPE MEI driver, version 1.4.8.5, (c) 2013 Lantiq Deutschland GmbH Lantiq CPE API Driver version: DSL CPE API V4.16.6.3 [ 122.928855] [ 122.928855] Predefined debug level: 3 [ 122.948035] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as rtc0 [ 122.953499] i2c-gpio i2c@0: using pins 482 (SDA) and 481 (SCL) [ 122.968334] hidraw: raw HID events driver (C) Jiri Kosina [ 122.988036] usbcore: registered new interface driver cdc_acm [ 122.992395] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 123.002237] usbcore: registered new interface driver cdc_wdm [ 123.007960] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68 [ 123.014008] Backport generated by backports.git backports-20151218-0-g2f58d9d [ 123.023802] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1 [ 123.029101] usbcore: registered new interface driver cpia2 [ 123.037943] gspca_main: v2.14.0 registered [ 123.044744] ip_tables: (C) 2000-2006 Netfilter Core Team [ 123.055743] Infineon Technologies DEU driver version 2.0.0 [ 123.061724] IFX DEU DES initialized (multiblock). [ 123.066594] IFX DEU AES initialized (multiblock). [ 123.070621] IFX DEU ARC4 initialized (multiblock). [ 123.075021] IFX DEU SHA1 initialized. [ 123.078667] IFX DEU MD5 initialized. [ 123.082137] IFX DEU SHA1_HMAC initialized. [ 123.086307] IFX DEU MD5_HMAC initialized. [ 123.099635] nf_conntrack version 0.5.0 (1933 buckets, 7732 max) [ 123.169837] NET: Registered protocol family 24 [ 123.177438] usbcore: registered new interface driver ums-alauda [ 123.184088] usbcore: registered new interface driver ums-cypress [ 123.190900] usbcore: registered new interface driver ums-datafab [ 123.197431] usbcore: registered new interface driver ums-freecom [ 123.204328] usbcore: registered new interface driver ums-isd200 [ 123.211236] usbcore: registered new interface driver ums-jumpshot [ 123.217894] usbcore: registered new interface driver ums-karma [ 123.225018] usbcore: registered new interface driver ums-sddr09 [ 123.231951] usbcore: registered new interface driver ums-sddr55 [ 123.239085] usbcore: registered new interface driver ums-usbat [ 123.246951] usbcore: registered new interface driver usbhid [ 123.251240] usbhid: USB HID core driver [ 123.285345] xt_time: kernel timezone is -0000 [ 123.291464] usbcore: registered new interface driver asix [ 123.298059] usbcore: registered new interface driver ax88179_178a [ 123.304382] usbcore: registered new interface driver cdc_eem [ 123.310876] usbcore: registered new interface driver cdc_ether [ 123.318826] usbcore: registered new interface driver cdc_ncm [ 123.351991] usbcore: registered new interface driver huawei_cdc_ncm [ 123.361439] usbcore: registered new interface driver kalmia [ 123.414183] usbcore: registered new interface driver Philips webcam [ 123.421703] usbcore: registered new interface driver rndis_host [ 123.429710] usbcore: registered new interface driver smsc95xx [ 123.439584] usbcore: registered new interface driver uvcvideo [ 123.443961] USB Video Class driver (1.1.1) [ 123.478053] usbcore: registered new interface driver cdc_mbim [ 123.498189] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 123.502599] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 123.635751] ieee80211 phy0: Atheros AR9300 Rev:4 mem=0xbc000000, irq=144 [ 130.318869] PTM 1.0.27 PTM (E1) firmware version 0.30 [ 130.327900] ifxmips_ptm: PTM init succeed [ 134.583006] IPv6: ADDRCONF(NETDEV_UP): ptm0: link is not ready [ 135.654241] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [..] [ 140.207476] wlan0: associated BusyBox v1.24.2 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- DESIGNATED DRIVER (Bleeding Edge, r49395) ----------------------------------------------------- * 2 oz. Orange Juice Combine all juices in a * 2 oz. Pineapple Juice tall glass filled with * 2 oz. Grapefruit Juice ice, stir well. * 2 oz. Cranberry Juice ----------------------------------------------------- root@OpenWrt:/#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/12/18 17:30
  • by danitool