Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:belkin:f7d3302 [2018/02/17 19:06] – ↷ Links adapted because of a move operation | toh:belkin:f7d3302 [2018/03/31 23:22] – ↷ Links adapted because of a move operation bobafetthotmail | ||
|---|---|---|---|
| Line 42: | Line 42: | ||
| ==== Keep the articles modular ==== | ==== Keep the articles modular ==== | ||
| | Please include only model specific information, | | Please include only model specific information, | ||
| - | | [[doc/ | + | | [[docs:start]] if you have no time to write certain stuff link to this | |
| - | | [[doc/ | + | | [[docs: |
| | DO NOT provide a complete howto here! Instead //groom// the general HowTos. | | DO NOT provide a complete howto here! Instead //groom// the general HowTos. | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | - → [[doc:howto: | + | - → [[:downloads]] |
| - | - → [[docs:user-guide: | + | - → [[docs: |
| - | - → **»»»»here»»»»[[about/ | + | - → **»»»»here»»»»[[:downloads|Latest OpenWrt release]]««««here««««** **DO NOT PROVIDE OWN LINKS to http:// |
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | Please check out the article [[doc:techref:Flash.Layout]]. It contains an example and a couple of explanations. | + | Please check out the article [[docs:techref:flash.layout]]. It contains an example and a couple of explanations. |
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| Line 70: | Line 70: | ||
| ==== OEM installation using the TFTP method ==== | ==== OEM installation using the TFTP method ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| === Specific values you need === | === Specific values you need === | ||
| Line 76: | Line 76: | ||
| | Bootloader tftp server IPv4 address | 192.168.2.1 | | | Bootloader tftp server IPv4 address | 192.168.2.1 | | ||
| | Bootloader MAC address (special) | FILL-IN | | | Bootloader MAC address (special) | FILL-IN | | ||
| - | | Firmware tftp image | [[about/ | + | | Firmware tftp image | [[:downloads|Latest OpenWrt release]] (**'' |
| | TFTP Transfer Window | (NONE, AFICT) | | | TFTP Transfer Window | (NONE, AFICT) | | ||
| | TFTP Window Start | approximately FILL-IN seconds after power on | | | TFTP Window Start | approximately FILL-IN seconds after power on | | ||
| Line 82: | Line 82: | ||
| ==== Upgrading OpenWrt ==== | ==== Upgrading OpenWrt ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | ||
| Line 108: | Line 108: | ||
| ===== Basic configuration ===== | ===== Basic configuration ===== | ||
| - | -> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ | + | -> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\ |
| Set up your Internet connection, configure wireless, configure USB port, etc. | Set up your Internet connection, configure wireless, configure USB port, etc. | ||
| Line 135: | Line 135: | ||
| ==== Failsafe mode ==== | ==== Failsafe mode ==== | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| Line 151: | Line 151: | ||
| | **[[wp> | | **[[wp> | ||
| | **Vendor: | | **Vendor: | ||
| - | | **[[doc:techref:Bootloader]]:** | [[doc: | + | | **[[docs:techref:bootloader]]:** | [[docs: |
| - | | **[[doc: | + | | **[[docs: |
| - | | **[[doc: | + | | **[[docs: |
| | **Flash size: | | **Flash size: | ||
| | **Flash Chip: | | **Flash Chip: | ||
| Line 159: | Line 159: | ||
| | **RAM Chip: | | **RAM Chip: | ||
| | **Wireless No1: | | **Wireless No1: | ||
| - | | **[[doc:hardware:Switch]]:** | Broadcom BCM5325EKQMG (100M, VLAN) | | + | | **[[docs: |
| | **USB: | | **USB: | ||
| - | | **[[doc: | + | | **[[docs: |
| - | | **[[doc: | + | | **[[docs: |
| ==== Photos ==== | ==== Photos ==== | ||
| Line 187: | Line 187: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the Serial Port of this specific device: | How to connect to the Serial Port of this specific device: | ||
| Line 202: | Line 202: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the JTAG Port of this specific device: | How to connect to the JTAG Port of this specific device: | ||
| Line 210: | Line 210: | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| On the serial console: | On the serial console: | ||
| Line 233: | Line 233: | ||
| ===== Bootloader Mods ===== | ===== Bootloader Mods ===== | ||
| - | - you could read about [[doc: | + | - you could read about [[docs: |
| ===== Hardware mods ===== | ===== Hardware mods ===== | ||
| - | - as a beginner, you really should inform yourself about [[doc: | + | - as a beginner, you really should inform yourself about [[docs: |