User Tools

Site Tools


toh:belkin:belkin_f9k1109_v1

Belkin F9K1109 v1

The F9K1109v1 is one of Belkin's N750 dual band N+ routers. It is based on the Ralink RT3883 SoC platform.

Supported Versions

Experimental Versions

None at this time.

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
F9K1109v1Ralink RT3883500864Ralink RT3883, Ralink RT3092Lb/g/na/n-5-2x 2.0

Installation

Flash Layout

Stock flash layout has 8 partitions:

  • 0x00000000-0x00800000 : “ALL”
  • 0x00000000-0x00030000 : “Bootloader”
  • 0x00030000-0x00040000 : “Config”
  • 0x00040000-0x00050000 : “Factory”
  • 0x00050000-0x0019d3e0 : “Kernel”
  • 0x0019d3e0-0x00800000 : “RootFS”
  • 0x00050000-0x007f0000 : “Kernel_RootFS”
  • 0x007f0000-0x00800000 : “UserCfg”

OpenWrt flash layout leaves the first 3 partitions and the last partition unchanged. Although they are renamed. Note the sizes of kernel, rootfs and rootfs_data are set based on the compiled kernel size so may change with new images.

  • 0x000000000000-0x000000030000 : “uboot”
  • 0x000000030000-0x000000040000 : “uboot-env”
  • 0x000000040000-0x000000050000 : “factory”
  • 0x000000050000-0x0000007f0000 : “firmware”
  • 0x000000000000-0x0000001657a4 : “kernel”
  • 0x0000001657a4-0x0000007a0000 : “rootfs”
  • 0x000000389000-0x0000007a0000 : “rootfs_data”
  • 0x0000007f0000-0x000000800000 : “user-cfg”

OEM easy installation

WARNING: The stock u-boot will fail to load a kernel after the kernel reaches a certain size. The snapshot builds are commonly that size.

It is ideal to have a serial connection to verify u-boot loads the kernel, but if you don't have one the upgrade will just stall forever and you can reload the stock firmware from Option 1 below.

The snapshot builds as of 4/1/19 will fail and the kernel is over 1.6M. If you do a local build through the image builder using the release config.seed the kernel is smaller 1.5M and will load.

Option 1 (from bootloader web)

This is the easier option. It uses a tiny web server in the stock u-boot bootloader. So you are using u-boot to update flash directly without loading the stock firmware. This skips some of the oddities and validations that the full stock firmware applies on image updates.

  • Hold reset button on the back of router when plugging in power (for at-least 10 seconds after plugged in)
  • Connect to a Lan port
  • Set computer IP to 10.10.10.3
  • Go to http://10.10.10.123 in a web browser
  • Click the Browse… Button and select the *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)

  • Go to firmware upgrade
  • Upload the factory image *initramfs.bin first
  • Boot into openwrt
  • From Luci web in openwrt upload the *squashfs.sysupgrade.bin

OEM installation using the TFTP method

generic.flashing.tftp

TFTP from stock is likely possible although has not been verified. The OEM easy installation - option 1 above has been verified and does not require any TFTP software on your PC. TFTP from serial has been verified to work with the ip addresses below

Bootloader tftp server IPv4 address 10.10.10.3
TFTP client required IP address 10.10.10.123

Upgrading OpenWrt

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Hardware

Info

General
Brand Belkin
Model F9K1109
Versions v1
Device Type WiFi Router
Availability Discontinued
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=f2c83532f92c5fa43165e1c5a3cd7f5cf4e9e3b3
Supported Since Release
Supported Current Release snapshot
Unsupported
Hardware
Instruction set
Sub Instruction Set
Bootloader U-Boot
Target ramips
System-On-Chip
CPU MHz 500
Flash MB 8
RAM MB 64
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch Realtek RTL8367R-VB
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n
WLAN Hardware Ralink RT3883, Ralink RT3092L
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 2x 2.0
SATA ports -
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count 4
Button count 2
Power supply 12 VDC, 2.0 A
Links
Forum Topic URL
WikiDevi URL
OEM device homepage URL http://¿
Firmware OEM Stock URL https://www.belkin.com/us/support-article?articleNum=5030
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL
Edit the underlying data View/Edit data

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Serial

port.serial general information about the serial port, serial port cable, etc.

Serial connection parameters 57600, 8N1

Serial Header

The 4 pin header is by “J12” on the board. As usual do not connect the power/volt connection.

GND RX TX 3.3V J12 marking on board

Hardware mods

None so far.

Bootlogs

OEM bootlog

ARC Uboot:1.7.4 (Dec 7 2011 - 09:22:22) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fa0000 spi_wait_nsec: 30 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D ..============================================ Ralink UBoot Version: 3.5.2.0 -------------------------------------------- ASIC 3883_MP (MAC to VITESSE Mode) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: DDR2 DRAM_SIZE: 512 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 64 MBytes Flash component: SPI Flash Date:Dec 7 2011 Time:09:22:22 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 500 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 4 initializing CHIP_RTL8367R_VB 1010 0 initializing CHIP_RTL8367R_VB 1010 3: System Boot system code via Flash. ## Booting image at bc050000 ... . Image Name: N750F9K1103VB Created: 2012-06-28 4:57:02 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 7398304 Bytes = 7.1 MB Load Address: 80000000 Entry Point: 8033e000 ................................................................................................................. Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8033e000) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.22 (kevinlin@arc-vcs) (gcc version 4.1.2) #2 Thu Jun 28 12:52:05 CST 2012 cmd line = console=ttyS1,57600n8 root=/dev/mtdblock5 init=/sbin/preinit The CPU feqenuce set to 500 MHz CPU revision is: 0001974c Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 init=/sbin/preinit Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). cause = c0808000, status = 11000000 PID hash table entries: 256 (order: 8, 1024 bytes) calculating r4koff... 001e8480(2000000) CPU frequency 500.00 MHz Using 250.000 MHz high precision timer. console handover: boot [early0] -> real [ttyS1] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61184k/65536k available (2649k kernel code, 4336k reserved, 666k data, 124k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_PCI_PCICFG_ADDR = 0 *************** Ralink PCIe RC mode ************* registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb [junius] pcibios_init Next Bus No=0 hose= 80307758 Mem=8030778C Io=803077A8 2->[1][0][0][30]=0 5->[1][0][0][30]=fffffffe 2->[1][0][0][30]=0 5->[1][0][0][30]=0 PCI: Bridge: 0000:00:00.0 IO window: disabled. MEM window: 20000000-200fffff PREFETCH window: disabled. BAR0 at slot 0 = 0 bus=0, slot = 0x0 P2P(PCI) 0x00 = 08021814 P2P(PCI) 0x04 = 00100007 P2P(PCI) 0x08 = 06040001 P2P(PCI) 0x0c = 00010000 P2P(PCI) 0x10 = 00000000 P2P(PCI) 0x14 = 20100000 P2P(PCI) 0x18 = 00010100 P2P(PCI) 0x1c = 000000f0 P2P(PCI) 0x20 = 20002000 P2P(PCI) 0x24 = 0000fff0 P2P(PCI) 0x28 = 00000000 P2P(PCI) 0x2c = 00000000 P2P(PCI) 0x30 = 00000000 P2P(PCI) 0x34 = 00000040 P2P(PCI) 0x38 = 00000000 P2P(PCI) 0x3c = 000401ff res[0]->start = 0 res[0]->end = 1ffffff res[1]->start = 20100000 res[1]->end = 2010ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=1, slot = 0x0 dev III(PCIe) 0x00 = 30911814 dev III(PCIe) 0x04 = 00100000 dev III(PCIe) 0x08 = 02800000 dev III(PCIe) 0x0c = 00000000 dev III(PCIe) 0x10 = 20000000 dev III(PCIe) 0x14 = 00000000 dev III(PCIe) 0x18 = 00000000 dev III(PCIe) 0x1c = 00000000 dev III(PCIe) 0x20 = 00000000 dev III(PCIe) 0x24 = 00000000 dev III(PCIe) 0x28 = 00000000 dev III(PCIe) 0x2c = 30911814 dev III(PCIe) 0x30 = 00000000 dev III(PCIe) 0x34 = 00000040 dev III(PCIe) 0x38 = 00000000 dev III(PCIe) 0x3c = 000001ff res[0]->start = 20000000 res[0]->end = 2000ffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 register_mtd_chip_driver for cfi_probe Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered deice id : c2 20 17 c2 20 (2017c220) MX25L6405D(c2 2017c220) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 8 MTD partitions on "raspi": 0x00000000-0x00800000 : "ALL" 0x00000000-0x00030000 : "Bootloader" 0x00030000-0x00040000 : "Config" 0x00040000-0x00050000 : "Factory" 0x00050000-0x0019d3e0 : "Kernel" mtd: partition "Kernel" doesn't end on an erase block -- force read-only 0x0019d3e0-0x00800000 : "RootFS" mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only 0x00050000-0x007f0000 : "Kernel_RootFS" 0x007f0000-0x00800000 : "UserCfg" RT3xxx EHCI/OHCI init. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher fuse init (API version 7.8) io scheduler noop registered (default) pcie_portdrv_probe->Dev[1814:0802] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Ralink gpio driver initialized spidrv_major = 217 ARC_KERNEL_OSIX_init() success HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: module loaded MAC_ADRH -- : 0x00000000 MAC_ADRL -- : 0x00000000 MAC_ADRH -- : 0x00000000 MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500! MAC_ADRH -- : 0x0000000c MAC_ADRL -- : 0x4328808e PROC INIT OK! Pull high SDA & SCK GPIO pin 24 reset to switch rtl8367_RouterVlanInit() rv=0 IsolateWanPort() rtk_vlan_set(VLAN1) rv=0 IsolateWanPort() rtk_vlan_set(VLAN2) rv=0 IsolateWanPort() rtk_vlan_get(VLAN1) rv=0 mbrmsk=ef untagmsk=f fid=0 IsolateWanPort() rtk_vlan_get(VLAN2) rv=0 mbrmsk=30 untagmsk=10 fid=1 IsolateWanPort() rtk_vlan_portPvid_get(0) rv=0 vid=1 pri=0 IsolateWanPort() rtk_vlan_portPvid_get(1) rv=0 vid=1 pri=0 IsolateWanPort() rtk_vlan_portPvid_get(2) rv=0 vid=1 pri=0 IsolateWanPort() rtk_vlan_portPvid_get(3) rv=0 vid=1 pri=0 IsolateWanPort() rtk_vlan_portPvid_get(4) rv=0 vid=2 pri=0 IsolateWanPort() rtk_vlan_portPvid_get(5) rv=0 vid=1 pri=0 rtl8367b driver initialized PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 block2mtd: version $Revision: 1.1.1.1 $ dev_nvram_init() 827 mtd->name=UserCfg rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 mcps_module_init() initializing Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 124k freed Warning: unable to open an initial console. Algorithmics/MIPS FPU Emulator v1.5 [sighandler]: No more events to be processed, quitting. [cleanup]: Waiting for children. [cleanup]: All children terminated. sysinit() done use original.... Assume Wi-Fi RadioOn everytime reboot!! connect: Network is unreachable rt2860v2_ap: module license 'unspecified' taints kernel. === pAd = c000f000, size = 487768 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 === pAd = c0307000, size = 513184 === <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc01a0000, csr_addr=0xc01a0000! Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. NET: Registered protocol family 10 MAC_ADRH -- : 0x00000886 MAC_ADRL -- : 0x3bb60a54 phy_tx_ring = 0x00340000, tx_ring = 0xa0340000 phy_rx_ring0 = 0x00341000, rx_ring0 = 0xa0341000 CDMA_CSG_CFG = 81000007 GDMA1_FWD_CFG = C0710000 eth2.1: dev_set_promiscuity(master, 1) device eth2 entered promiscuous mode device eth2.1 entered promiscuous mode br0: port 1(eth2.1) entering learning state force port 0 up force port 1 up force port 2 up force port 3 up rmmod: hw_nat CHIPID=RT3883 Ralink HW NAT Module Enabled /bin/mknod /dev/ac0 c 240 0 Policy Table Base=B0101000 Offset=3320 B0101CF8: 00110F01 B0101CFC: 00000000 done Policy Table Base=B0101000 Offset=3320 B0101CF8: 00110F01 B0101CFC: 00000000 Policy Table Base=B0101000 Offset=3328 B0101D00: 00210F05 B0101D04: 00000000 done Starting HotPlug: /usr/sbin/hotplugd -D -f Starting jcpd daemon: /usr/sbin/jcpd br0: topology change detected, propagating br0: port 1(eth2.1) entering forwarding state fw_rule_isolatedlan: br0 fw_rule_isolatedlan: br0 fw_rule_isolatedlan: br1 fw_rule_isolatedlan: br1 fw_rule_isolatedlan: br0 fw_rule_isolatedlan: br1 fw_rule_SkipSnatToLans: br0 fw_rule_SkipSnatToLans: br1 fw_rule_SkipDnatFromLans: br0 fw_rule_SkipDnatFromLans: br1 RX DESC a0357000 size = 2048 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 8 2. Phy Mode = 8 3. Phy Mode = 8 RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff ff 00 01 SYNC - BBP R4 to 20MHz.l Starting Samba: /usr/sbin/smbd -D Main bssid = 08:86:3b:b6:0a:56 <==== rt28xx_init, Status=0 0x1300 = 00064380 /usr/sbin/nmbd -D device ra0 entered promiscuous mode br0: port 2(ra0) entering learning state RX DESC a2ce7000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 br0: topology change detected, propagating br0: port 2(ra0) entering forwarding state Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 00 SYNC - BBP R4 to 20MHz.l Starting sxuptpd USB port mode selector has been enabled Initializing USB port mode: port1 = NAS port2 = NAS usbcore: registered new interface driver sxuptp_driver Starting usbjcpd insmod: cannot insert '/lib/modules/2.6.22/kernel/drivers/usb/storage/usb-storage.ko': Invalid parameters (17): Invalid argument Main bssid = 08:86:3b:b6:0a:54 <==== rt28xx_init, Status=0 0x1300 = 00064380 device rai0 entered promiscuous mode br0: port 3(rai0) entering learning state br0: topology change detected, propagating br0: port 3(rai0) entering forwarding state do init wsc MsgQ System Initializationeth2.2: Setting MAC address to ! 08 86 3b b6 0a 55. < rc_wan_start: 640>: ifconfig eth2.2 up Create netlink socket thread success! Create ioctl socket(6) success! Create wscd udhcpc_main(452): udhcp client (v0.9.8) started rc_nat_dmz_stop, 256 rc_nat_dmz_action nat_dmz_rule_flush, 67: wan_index 0 set FW_DMZ_STAT 0 with wan_index 0 ipv6 started 0 CFG_NAT_DMZ_HOST = 2139826600 host = rc_nat_vts_stop, 336 share memory key=74565 successful id on creating=32769 led_process_init() eco=0 wpsm_upnp_attach() OK signalling RUNNING rc_fw_macflt_stop : 163 start Eco_mode ***** g_wl_interface = rai0 ****** start belkin_wan_cfg rc_nat_Masquerade_stop, 182 rc_nat_Masquerade_action nat_Masquerade_rule_flush lld2d: listening on interface br0 belkin_wan_cfg running on 102a8c0 Succeed cTmpString = Fortman ctrl_flags=0x38 mcps: mcps_netlink_rcv() nlh->nlmsg_len=528mcps: mcps_process_registration() mcps_pid=958 mcps: mcps_process_registration() set control flag 0x38 UPnP daemon is ready to run udhcpc_main(737): Received SIGTERM Daemonizing... /usr/local/twonky/twonkystarter -D -appdata /tmp/twonky WaitUntilTwonkyRPCReady[1018]: twonky_cmd[879]: wget -O /tmp/twonky_cmd "http://127.0.0.1:9000/rpc/info_status" /bin/mknod /dev/ARCOSIX_DEV c 253 0 Connecting to 127.0.0.1:9000 (127.0.0.1:9000) wget: cannot connect to remote host (127.0.0.1): Connection refused /tmp/twonky_cmd: No such file or directory WaitUntilTwonkyRPCReady: count 19, ret 0 twonky_cmd[879]: wget -O /tmp/twonky_cmd "http://127.0.0.1:9000/rpc/info_status" Connecting to 127.0.0.1:9000 (127.0.0.1:9000) twonky_cmd 100% |*******************************| 341 --:--:-- ETA serverkind|ME WaitUntilTwonkyRPCReady: count 18, ret 1 twonky_add_drive starting NO USB MOUNTED twonky_add_drive[737]: DONE rc_twonky_start: 1118 rc_all_start 112


OpenWrt bootlog

ARC Uboot:1.7.4 (Dec 7 2011 - 09:22:22) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fa0000 ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 30 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D ..============================================ Ralink UBoot Version: 3.5.2.0 -------------------------------------------- ASIC 3883_MP (MAC to VITESSE Mode) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: DDR2 DRAM_SIZE: 512 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 64 MBytes Flash component: SPI Flash Date:Dec 7 2011 Time:09:22:22 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 500 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 4 initializing CHIP_RTL8367R_VB 1010 0 initializing CHIP_RTL8367R_VB 1010 3: System Boot system code via Flash. ## Booting image at bc050000 ... . Image Name: N750F9K1103VB Created: 2019-03-03 1:46:05 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1469187 Bytes = 1.4 MB Load Address: 80000000 Entry Point: 80000000 ....................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 4.14.103 (kip@dev-ub-openwrt) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9508-c1a8054114)) #0 Sun Mar 3 01:46:05 2019 [ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is Belkin F9K1109 Version 1.0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] random: get_random_bytes called from 0x803ed72c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60452K/65536K available (3391K kernel code, 165K rwdata, 456K rodata, 204K init, 199K bss, 5084K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.015471] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232) [ 0.097755] pid_max: default: 32768 minimum: 301 [ 0.107178] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.120204] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.140137] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.159623] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.171803] pinctrl core: initialized pinctrl subsystem [ 0.182694] NET: Registered protocol family 16 [ 0.195980] rt3883-pci 10140000.pci: mode: PCIe [ 1.835666] PCI host bridge /pci@10140000/pci@0 ranges: [ 1.845944] MEM 0x0000000020000000..0x000000002fffffff [ 1.856303] IO 0x0000000010160000..0x000000001016ffff [ 1.867931] Can't analyze schedule() prologue at 8034b8f4 [ 1.892920] rt2880_gpio 10000600.gpio: registering 24 gpios [ 1.903956] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 1.916601] rt2880_gpio 10000638.gpio: registering 16 gpios [ 1.928580] PCI host bridge to bus 0000:00 [ 1.936584] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 1.950302] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 1.962027] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.975526] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.991745] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.008287] pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 2.021694] pci 0000:00:01.0: BAR 1: assigned [mem 0x20100000-0x2010ffff] [ 2.035164] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff] [ 2.048655] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.058509] pci 0000:00:01.0: bridge window [mem 0x20000000-0x200fffff] [ 2.076888] clocksource: Switched to clocksource MIPS [ 2.088219] NET: Registered protocol family 2 [ 2.097787] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 2.111565] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 2.124158] TCP: Hash tables configured (established 1024 bind 1024) [ 2.136994] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 2.148496] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 2.161238] NET: Registered protocol family 1 [ 2.172986] rt-timer 10000100.timer: maximum frequency is 5065Hz [ 2.185849] Crashlog allocated RAM at address 0x3f00000 [ 2.198248] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 2.217269] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.228759] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.259854] io scheduler noop registered [ 2.267562] io scheduler deadline registered (default) [ 2.278664] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.292481] console [ttyS0] disabled [ 2.299546] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 2.319209] console [ttyS0] enabled [ 2.319209] console [ttyS0] enabled [ 2.333020] bootconsole [early0] disabled [ 2.333020] bootconsole [early0] disabled [ 2.349528] cacheinfo: Failed to find cpu0 device node [ 2.359806] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 2.377299] spi spi0.0: force spi mode3 [ 2.385755] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 2.395590] 5 fixed-partitions partitions found on MTD device spi0.0 [ 2.408260] Creating 5 MTD partitions on "spi0.0": [ 2.417822] 0x000000000000-0x000000030000 : "uboot" [ 2.428582] 0x000000030000-0x000000040000 : "uboot-env" [ 2.440031] 0x000000040000-0x000000050000 : "factory" [ 2.451180] 0x000000050000-0x0000007f0000 : "firmware" [ 2.465944] 2 uimage-fw partitions found on MTD device firmware [ 2.477807] Creating 2 MTD partitions on "firmware": [ 2.487728] 0x000000000000-0x000000166b43 : "kernel" [ 2.498607] 0x000000166b43-0x0000007a0000 : "rootfs" [ 2.509497] mtd: device 5 (rootfs) set to be root filesystem [ 2.522557] 1 squashfs-split partitions found on MTD device rootfs [ 2.534954] 0x00000038c000-0x0000007a0000 : "rootfs_data" [ 2.546777] 0x0000007f0000-0x000000800000 : "user-cfg" [ 2.558970] libphy: Fixed MDIO Bus: probed [ 2.570644] mtk_soc_eth 10100000.ethernet: generated random MAC address 66:d3:08:7b:e1:93 [ 2.587018] mtk_soc_eth 10100000.ethernet: using fixed link parameters [ 2.600042] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): link up (1000Mbps/Full duplex) [ 2.617995] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 2.635096] rt2880_wdt 10000120.watchdog: Initialized [ 2.646715] NET: Registered protocol family 10 [ 2.660089] Segment Routing with IPv6 [ 2.667599] NET: Registered protocol family 17 [ 2.676520] 8021q: 802.1Q VLAN Support v1.8 [ 2.697001] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 2.712518] Freeing unused kernel memory: 204K [ 2.721407] This architecture does not have kernel memory protection. [ 2.734239] random: fast init done [ 5.365645] init: Console is alive [ 5.372775] init: - watchdog - [ 6.414562] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.710642] usbcore: registered new interface driver usbfs [ 6.721744] usbcore: registered new interface driver hub [ 6.732492] usbcore: registered new device driver usb [ 6.749513] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.764539] ehci-platform: EHCI generic platform driver [ 6.785386] phy phy-usbphy.0: remote usb device wakeup disabled [ 6.797200] phy phy-usbphy.0: UTMI 16bit 30MHz [ 6.806062] ehci-platform 101c0000.ehci: EHCI Host Controller [ 6.817566] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 6.833490] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 6.866912] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 6.880532] hub 1-0:1.0: USB hub found [ 6.888513] hub 1-0:1.0: 2 ports detected [ 6.900560] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.914880] ohci-platform: OHCI generic platform driver [ 6.925680] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 6.939279] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 6.955159] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 7.042019] hub 2-0:1.0: USB hub found [ 7.050013] hub 2-0:1.0: 2 ports detected [ 7.064409] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 7.089399] init: - preinit - [ 8.278840] mtk_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex) [ 8.294354] 8021q: adding VLAN 0 to HW filter on device eth0 [ 8.323778] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 11.768918] mount_root: no usable overlay filesystem found, using tmpfs overlay [ 11.817398] urandom-seed: Seed file not found (/etc/urandom.seed) [ 12.169143] mtk_soc_eth 10100000.ethernet eth0: link down [ 12.193561] procd: - early - [ 12.199514] procd: - watchdog - [ 13.370906] procd: - watchdog - [ 13.377583] procd: - ubus - [ 14.439178] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.721560] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.734944] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.748834] procd: - init - [ 15.342737] kmodloader: loading kernel modules from /etc/modules.d/* [ 15.365668] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 15.388676] Loading modules backported from Linux version v4.19.23-0-g67d52fae61c1 [ 15.403828] Backport generated by backports.git v4.19.23-1-0-g480a925a Please press Enter to activate t[ 15.424733] ip_tables: (C) 2000-2006 Netfilter Core Team his console. [ 15.447197] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 15.537281] xt_time: kernel timezone is -0000 [ 15.612211] PPP generic driver version 2.4.2 [ 15.624083] NET: Registered protocol family 24 [ 15.666402] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 15.679126] rt2800pci 0000:01:00.0: loaded eeprom from mtd device "factory" [ 15.693084] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected [ 15.708540] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected [ 15.740111] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 15.754587] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3883, rev 0400 detected [ 15.770045] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 3853 detected [ 16.126565] kmodloader: done loading kernel modules from /etc/modules.d/* [ 18.245411] urandom_read: 5 callbacks suppressed [ 18.245422] random: jshn: uninitialized urandom read (4 bytes read) [ 43.128265] jffs2_scan_eraseblock(): End of filesystem marker found at 0x4000 [ 43.173414] jffs2_build_filesystem(): unlocking the mtd device... [ 43.173427] done. [ 43.189652] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 44.431965] mtk_soc_eth 10100000.ethernet eth0: link up (1000Mbps/Full duplex) [ 44.462122] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 44.473808] 8021q: adding VLAN 0 to HW filter on device eth0 [ 44.720991] device eth0 entered promiscuous mode [ 44.767402] br-lan: port 1(eth0.1) entered blocking state [ 44.778223] br-lan: port 1(eth0.1) entered disabled state [ 44.789401] device eth0.1 entered promiscuous mode [ 44.945809] br-lan: port 1(eth0.1) entered blocking state [ 44.956637] br-lan: port 1(eth0.1) entered forwarding state [ 44.967980] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 45.487048] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 45.500362] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 83.542292] done. [ 83.546167] jffs2: notice: (1153) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 83.838390] overlayfs: upper fs does not support tmpfile. [ 127.236949] random: crng init done BusyBox v1.30.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r9508-c1a8054114 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/belkin/belkin_f9k1109_v1.txt · Last modified: 2019/10/26 07:34 by tmomas