Beeline SmartBox PRO

OEM/ODM name: Sercomm S1500 AWI. The Beeline SmartBox PRO is a CPE wireless router based on the MT7621 platform.

Beeline SmartBox PRO

  1. Remove all dots from the factory image filename (except the dot before file extension)
  2. Upload and update the firmware via the original web interface
  3. Two options are possible after the reboot:
    • OpenWrt - that's OK, the mission accomplished
    • Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image.

1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:

printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2

2. Optional: Update with any version of stock firmware if you want to overwrite OpenWrt in Slot 0 completely.

1. Compile sercomm-recovery under the Linux:

git clone https://github.com/danitool/sercomm-recovery.git
make

2. Connect the router with a cable and run sercomm-recovery:

sudo ./sercomm-recovery enp0s3 recovery.bin

where:

  • enp0s3 - network interface connected the router
  • ifconfig - list on available network interfaces
  • recovery.bin - recovery image

3. Wait until the router is flashed and rebooted.

Download ready recovery images for Sercomm devices.

It's also possible to create a recovery image containing OpenWrt.

How to make own recovery images

You can use mtd0 (“ALL”) backup as a recovery image.

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

FIXME Replace EXAMPLE by real values.

J4 GND Tx VCC Rx

Sercomm S1500 UART1

Serial connection parameters
for Beeline SmartBox PRO
EXAMPLE 57600, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

FIXME Notes need to be moved.

nTRST GND 1 2 TDI GND 3 4 TDO GND 5 6 TMS GND 7 8 TCK GND 9 10 nSRST n/a 11 12 DINT Vcc 13 14 J3

Warning!
This section describes actions that might damage your device or firmware. Proceed with care!

Input conditions:

  • router with Breed bootloader installed

You will need:

  • PC or Virtual machine with Linux
  • mtd partitions backup (uboot.bin - u-boot bootloader, factory.bin - Factory)
  • http server with mtd partitions backup (i.e. with IP 192.168.1.2)
  • recovery image (see sercomm-recovery_utility)

U-Boot and stock firmware recovery steps

After executing each command, carefully read its output before executing the next one.

1. Enter the Breed telnet shell (IP: 192.168.1.1)

2. Download Factory backup from your http server and write it:

wget http://192.168.1.2/factory.bin
flash erase 0x100000 0x100000
flash write 0x100000 0x80001000 0x100000

3. Download u-boot bootloader backup from your http server and write it:

The most dangerous part of the instruction. Be extremely careful.

wget http://192.168.1.2/uboot.bin
flash erase 0x0 0x100000
flash write 0x0 0x80001000 0x100000

4. Check written data and reboot:

flash dump 0x0
flash dump 0x100000

5. Use sercomm-recovery utility for stock firmware recovery

=================================================================== MT7621 stage1 code 10:40:45 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x0, 1/0 = 870/154 01000000 PLL2 FB_DL: 0xc, 1/0 = 624/400 31000000 PLL4 FB_DL: 0x16, 1/0 = 639/385 59000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 80 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00002222 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 7 11 8 7 7 8 5 6 6 10 | 9 9 7 9 7 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =34 DQS1 = 34 ================================================================== bit DQS0 bit DQS1 0 (1~67)34 8 (1~63)32 1 (1~65)33 9 (1~62)31 2 (1~67)34 10 (1~68)34 3 (1~65)33 11 (1~64)32 4 (1~67)34 12 (1~65)33 5 (1~68)34 13 (0~61)30 6 (1~63)32 14 (1~68)34 7 (1~66)33 15 (1~66)33 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 8 11 9 7 7 10 6 8 9 10 | 9 11 8 13 7 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Oct 17 2014 - 17:37:52) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffac000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 8ffe0cd0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 DA 90 95 44] Device not found, ID: c8da Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c8da select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 2047 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 Env addr : 0x800000 .*** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.0.6 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Oct 17 2014 Time:17:37:52 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN LLLLW ..Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000D cmd : 0x0000000D Press Ctrl+C to Enter the Main loop... 0 Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, boot Flash Sector Number : 2048. Bad block detected at 0x17640, oob_buf[0] is 0x0 NAND Section 9, has bad block at address c7b20000, Image Offset bb20000 NAND Section 9, has bad block count 1 *************************************************** Sercomm Boot Version 4.10.0 *************************************************** Entering Firmware : Everything is OK. Begin to verify the backup image... kernel addr: 0x1B00100 len: 0x26A49B crc: 0x2B8C8EB1 ........................................calculate_kernel_crc: 0x2B8C8EB1 ok! Second image selected kernel addr :0xc1700100 kernel addr :0xC1700100 ## Booting image at c1700100 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2532443 Bytes = 2.4 MB Load Address: 80001000 Entry Point: 8000f500 ....................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK commandline in boot is : console=ttyS1,57600 ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs !!!! No initrd ## Transferring control to Linux (at address 8000f500) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36+ (eddie@ubuntu) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Dec 9 05:22:14 CST 2014 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 10000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Detected 3 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @81204000 s6976 r8192 d13504 u65536 pcpu-alloc: s6976 r8192 d13504 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS1,57600 ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=00018001 Readback ErrCtl register=00018001 Memory: 251984k/262144k available (5411k kernel code, 10160k reserved, 1759k data, 220k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu2 launch: cpu2 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu3 launch: cpu3 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 4 CPUs Synchronize counters across 4 CPUs: done. hrtimer start on CPU1 NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60400000-0x6040ffff] (PCI address [0x60400000-0x6040ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60410000-0x6041ffff] (PCI address [0x60410000-0x6041ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff 64bit] (PCI address [0x60200000-0x602fffff] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60400000 res[1]->end = 6040ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60410000 res[1]->end = 6041ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60200000 res[0]->end = 602fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 5, 163840 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 128 (order: 0, 6144 bytes) UDP-Lite hash table entries: 128 (order: 0, 6144 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1069056) squashfs: version 4.0 (2009/01/31) Phillip Lougher NTFS driver 2.1.29 [Flags: R/W]. fuse init (API version 7.15) msgmni has been set to 492 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 8076c610 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 DA 90 95 44, 00909544] Device not found, ID: c8da Not Support this Device! chip_mode=00000001 [NAND] pagesz:2048 , oobsz: 288,eccbytes: 32 Support this Device in MTK table! c8da NAND device: Manufacturer ID: 0xc8, Chip ID: 0xda (Unknown NAND 256MiB 3,3V 8-bit) [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 2047 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 13 MTD partitions on "MT7621-NAND": 0x000000000000-0x00000ff80000 : "ALL" Bad block detected at 0x17640, oob_buf[0] is 0x0 0x000000000000-0x000000100000 : "Bootloader" 0x000000100000-0x000000200000 : "Factory" 0x000000200000-0x000001600000 : "sys_data" 0x000001600000-0x000001700000 : "boot_flag" 0x000001700000-0x000001b00000 : "Kernel_1" 0x000001b00000-0x000001f00000 : "Kernel_2" 0x000001f00000-0x000003d00000 : "RootFS_1" 0x000003d00000-0x000005b00000 : "RootFS_2" 0x000005b00000-0x000008d00000 : "JVM/OSGI1" 0x000008d00000-0x00000bf00000 : "JVM/OSGI2" Bad block detected at 0x17640, oob_buf[0] is 0x0 0x00000bf00000-0x00000fb00000 : "OSGI data" 0x00000fb00000-0x00000fc00000 : "Ftool" [mtk_nand] probe successfully! UBI: attaching mtd8 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 28 UBI: attached mtd8 to ubi0 UBI: MTD device name: "RootFS_2" UBI: MTD device size: 30 MiB UBI: number of good PEBs: 240 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 240 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBI: image sequence number: 0 ps: can't get major 253 UBI: background thread "ubi_bgt0d" started, PID 54 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x432880e2 Ralink APSoC Ethernet Driver Initilization. v3.1 4096 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x4328801f PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. usbcore: registered new interface driver catc catc: v2.8:CATC EL1210A NetMate USB Ethernet driver usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus register rt2860 === pAd = c0202000, size = 1262256 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0100000, csr_addr=0xc0100000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is FLASH mode === pAd = c0482000, size = 1262256 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0380000, csr_addr=0xc0380000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is FLASH mode FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 [USB] Device 'xHCI Host Controller xhc_mtk'is plugged into port 1. usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 2.6.36+ xhci-hcd usb usb1: SerialNumber: xhc_mtk hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 [USB] Device 'xHCI Host Controller xhc_mtk'is plugged into port 2. usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 2.6.36+ xhci-hcd usb usb2: SerialNumber: xhc_mtk hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Ralink APSoC Hardware Watchdog Timer Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3937 buckets, 15748 max) matchsize=264 xt_time: kernel timezone is -0000 GRE over IPv4 demultiplexor driver gre: can't add protocol ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: file system size: 28315648 bytes (27652 KiB, 27 MiB, 223 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: zlib UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) on device 0:11. Started WatchDog Timer. Freeing unused kernel memory: 220k freed init started: BusyBox v1.15.3 () starting pid 64, tty '': '/etc.ro/rcS' Algorithmics/MIPS FPU Emulator v1.5 UBI: attaching mtd3 to ubi3 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 16 UBI: attached mtd3 to ubi3 UBI: MTD device name: "sys_data" UBI: MTD device size: 20 MiB UBI: number of good PEBs: 160 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 160 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBI: image sequence number: 521320234 UBI: background thread "ubi_bgt3d" started, PID 103 UBI device number 3, total 160 LEBs (20316160 bytes, 19.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 3, volume 0, name "sys_data" UBIFS: file system size: 18157568 bytes (17732 KiB, 17 MiB, 143 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: zlib UBIFS: reserved for root: 0 bytes (0 KiB) sc_drv: module license 'Sercomm' taints kernel. Disabling lock debugging due to kernel taint starting pid 112, tty '/dev/ttyS1': '/bin/sh' BusyBox v1.15.3 () built-in shell (ash) Enter 'help' for a list of built-in commands. / # [util_brd.c][read_protected_data_to_ram][199]: key=A1b2C3d4E5 [main]read config /etc/default.xml success [CM_XML2RAM]xml file to RAM ret=0 ap_name=syslogd, action=start ap_name=coredump, action=start Raeth v3.1 (Tasklet) phy_tx_ring = 0x0e184000, tx_ring = 0xae184000 phy_rx_ring0 = 0x0e190000, rx_ring0 = 0xae190000 change HW-TRAP to 0x17ccf set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000944a GMAC1_MAC_ADRL -- : 0x0c543201 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 ESW: Link Status Changed - Port2 Link UP hrtimer: interrupt took 42391 ns Chain 'FORWARD_WIFI' doesn't exist. restore_ft_tool get ftool header sucess get ftool magic check failed ap_name=dnrd, action=start ap_name=phy, action=start device eth2 entered promiscuous mode switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 switch reg write offset=2610, value=81000000 ap_name=iptv_bridge, action=start IPTV Port Mask 0000 old_vlan 1111 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10002 switch reg write offset=2514, value=10001 REG_ESW_WT_MAC_ATC is 0x7ff0002 device eth2.1 entered promiscuous mode done. Set: phy[31].reg[24] = 2ff70 Set: phy[31].reg[12512] = 2125 ap_name=lanip, action=start br0: port 1(eth2.1) entering learning state br0: port 1(eth2.1) entering learning state Set: phy[0].reg[0] = 3300 info, udhcp server (v0.9.7) started Set: phy[1].reg[0] = 3300 ESW: Link Status Changed - Port2 Link Down Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 ap_name=telnetd, action=start ap_name=sshd, action=start ap_name=httpd, action=start ap_name=redirect, action=start bind: Address already in use ap_name=dnrd, action=start redirect ap_name=bftpd, action=start ap_name=firewall, action=start br0: port 1(eth2.1) entering forwarding state nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading ESW: Link Status Changed - Port2 Link UP ap_name=srt, action=restart ap_name=rp, action=start ap_name=mediaserver, action=restart killall: minidlna: no process killed ap_name=ntp, action=start ap_name=hwim, action=start ap_name=cpm, action=start ap_name=wanip, action=stop 2 ap_name=dnrd, action=stop wid 2 ap_name=wanip, action=stop 3 ap_name=igmp_proxy, action=stop 3 ap_name=dnrd, action=stop wid 3 ap_name=igd_upnp, action=start ap_name=wlan, action=start interface ra1 does not exist! ifconfig: SIOCGIFFLAGS: No such device device ra0 is not a slave of br0 build time = 20140408060640a rom patch for E3 IC platform = ALPS hw/sw version = �� patch version = FW Version:0.0.00 Build:1 Build Time:201406241830____ fw for E3 IC RX[0] DESC af67f000 size = 4096 RX[1] DESC af690000 size = 4096 RTMP_TimerListAdd: add timer obj c0522c34! RTMP_TimerListAdd: add timer obj c0496258! RTMP_TimerListAdd: add timer obj c0495e3c! RTMP_TimerListAdd: add timer obj c0496228! RTMP_TimerListAdd: add timer obj c0496574! RTMP_TimerListAdd: add timer obj c04964a4! RTMP_TimerListAdd: add timer obj c04964d4! RTMP_TimerListAdd: add timer obj c049950c! RTMP_TimerListAdd: add timer obj c04990f0! RTMP_TimerListAdd: add timer obj c04994dc! RTMP_TimerListAdd: add timer obj c0499828! RTMP_TimerListAdd: add timer obj c0499758! RTMP_TimerListAdd: add timer obj c0499788! RTMP_TimerListAdd: add timer obj c049c7c0! RTMP_TimerListAdd: add timer obj c049c3a4! RTMP_TimerListAdd: add timer obj c049c790! RTMP_TimerListAdd: add timer obj c049cadc! RTMP_TimerListAdd: add timer obj c049ca0c! RTMP_TimerListAdd: add timer obj c049ca3c! RTMP_TimerListAdd: add timer obj c049fa74! RTMP_TimerListAdd: add timer obj c049f658! RTMP_TimerListAdd: add timer obj c049fa44! RTMP_TimerListAdd: add timer obj c049fd90! RTMP_TimerListAdd: add timer obj c049fcc0! RTMP_TimerListAdd: add timer obj c049fcf0! RTMP_TimerListAdd: add timer obj c04a2d28! RTMP_TimerListAdd: add timer obj c04a290c! RTMP_TimerListAdd: add timer obj c04a2cf8! RTMP_TimerListAdd: add timer obj c04a3044! RTMP_TimerListAdd: add timer obj c04a2f74! RTMP_TimerListAdd: add timer obj c04a2fa4! RTMP_TimerListAdd: add timer obj c04a5fdc! RTMP_TimerListAdd: add timer obj c04a5bc0! RTMP_TimerListAdd: add timer obj c04a5fac! RTMP_TimerListAdd: add timer obj c04a62f8! RTMP_TimerListAdd: add timer obj c04a6228! RTMP_TimerListAdd: add timer obj c04a6258! RTMP_TimerListAdd: add timer obj c04a9290! RTMP_TimerListAdd: add timer obj c04a8e74! RTMP_TimerListAdd: add timer obj c04a9260! RTMP_TimerListAdd: add timer obj c04a95ac! RTMP_TimerListAdd: add timer obj c04a94dc! RTMP_TimerListAdd: add timer obj c04a950c! RTMP_TimerListAdd: add timer obj c04ac544! RTMP_TimerListAdd: add timer obj c04ac128! RTMP_TimerListAdd: add timer obj c04ac514! RTMP_TimerListAdd: add timer obj c04ac860! RTMP_TimerListAdd: add timer obj c04ac790! RTMP_TimerListAdd: add timer obj c04ac7c0! RTMP_TimerListAdd: add timer obj c04ce984! RTMP_TimerListAdd: add timer obj c04ceaa0! RTMP_TimerListAdd: add timer obj c04ce9b0! RTMP_TimerListAdd: add timer obj c04c6134! E2pAccessMode=2 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 14 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 14 RTMP_TimerListAdd: add timer obj c04936a8! RTMP_TimerListAdd: add timer obj c049695c! RTMP_TimerListAdd: add timer obj c0499c10! RTMP_TimerListAdd: add timer obj c049cec4! RTMP_TimerListAdd: add timer obj c04a0178! RTMP_TimerListAdd: add timer obj c04a342c! RTMP_TimerListAdd: add timer obj c04a66e0! RTMP_TimerListAdd: add timer obj c04a9994! RTMP_TimerListAdd: add timer obj c04c5e48! 3. Phy Mode = 14 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 TX0 power compensation = 0x38 TX1 power compensation = 0x38 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 0, false cca 553 UpdateChannelInfo: chan 0, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 1, false cca 1156 UpdateChannelInfo: chan 1, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 2, false cca 138 UpdateChannelInfo: chan 2, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 3, false cca 943 UpdateChannelInfo: chan 3, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 4, false cca 1073 UpdateChannelInfo: chan 4, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 5, false cca 2015 UpdateChannelInfo: chan 5, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 6, false cca 568 UpdateChannelInfo: chan 6, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 7, false cca 671 UpdateChannelInfo: chan 7, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 8, false cca 668 UpdateChannelInfo: chan 8, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 9, false cca 299 UpdateChannelInfo: chan 9, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 10, false cca 1692 UpdateChannelInfo: chan 10, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 11, false cca 2171 UpdateChannelInfo: chan 11, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 UpdateChannelInfo: chan 12, false cca 2615 UpdateChannelInfo: chan 12, BusyTime 0, duration 400 RTMP_TimerListAdd: add timer obj c04c6424! mt76x2_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=3, HT-CentCh=5, VHT-CentCh=0 mt76x2_single_sku::DefaultTargetPwr = 37 mt76x2_single_sku::DefaultTargetPwr = 0x25, delta_power = 0x0 APStartUp(): AP Set CentralFreq at 5(Prim=3, HT-CentCh=5, VHT-CentCh=0, BBP_BW=1) mt76x2_calibration(channel = 5) The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 Main bssid = 94:4a:0c:54:32:01 mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 original vga value(chain0) = 5c original vga value(chain1) = 5c <==== rt28xx_init, Status=0 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! device ra0 entered promiscuous mode br0: port 2(ra0) entering learning state br0: port 2(ra0) entering learning state device rai0 is not a slave of br0 build time = 20140408060640a rom patch for E3 IC platform = ALPS hw/sw version = �� patch version = FW Version:0.0.00 Build:1 Build Time:201406241830____ fw for E3 IC RX[0] DESC af4f1000 size = 4096 RX[1] DESC af4f2000 size = 4096 RTMP_TimerListAdd: add timer obj c02a2c34! RTMP_TimerListAdd: add timer obj c0216258! RTMP_TimerListAdd: add timer obj c0215e3c! RTMP_TimerListAdd: add timer obj c0216228! RTMP_TimerListAdd: add timer obj c0216574! RTMP_TimerListAdd: add timer obj c02164a4! RTMP_TimerListAdd: add timer obj c02164d4! RTMP_TimerListAdd: add timer obj c021950c! RTMP_TimerListAdd: add timer obj c02190f0! RTMP_TimerListAdd: add timer obj c02194dc! RTMP_TimerListAdd: add timer obj c0219828! RTMP_TimerListAdd: add timer obj c0219758! RTMP_TimerListAdd: add timer obj c0219788! RTMP_TimerListAdd: add timer obj c021c7c0! RTMP_TimerListAdd: add timer obj c021c3a4! RTMP_TimerListAdd: add timer obj c021c790! RTMP_TimerListAdd: add timer obj c021cadc! RTMP_TimerListAdd: add timer obj c021ca0c! RTMP_TimerListAdd: add timer obj c021ca3c! RTMP_TimerListAdd: add timer obj c021fa74! RTMP_TimerListAdd: add timer obj c021f658! RTMP_TimerListAdd: add timer obj c021fa44! RTMP_TimerListAdd: add timer obj c021fd90! RTMP_TimerListAdd: add timer obj c021fcc0! RTMP_TimerListAdd: add timer obj c021fcf0! RTMP_TimerListAdd: add timer obj c0222d28! RTMP_TimerListAdd: add timer obj c022290c! RTMP_TimerListAdd: add timer obj c0222cf8! RTMP_TimerListAdd: add timer obj c0223044! RTMP_TimerListAdd: add timer obj c0222f74! RTMP_TimerListAdd: add timer obj c0222fa4! RTMP_TimerListAdd: add timer obj c0225fdc! RTMP_TimerListAdd: add timer obj c0225bc0! RTMP_TimerListAdd: add timer obj c0225fac! RTMP_TimerListAdd: add timer obj c02262f8! RTMP_TimerListAdd: add timer obj c0226228! RTMP_TimerListAdd: add timer obj c0226258! RTMP_TimerListAdd: add timer obj c0229290! RTMP_TimerListAdd: add timer obj c0228e74! RTMP_TimerListAdd: add timer obj c0229260! RTMP_TimerListAdd: add timer obj c02295ac! RTMP_TimerListAdd: add timer obj c02294dc! RTMP_TimerListAdd: add timer obj c022950c! RTMP_TimerListAdd: add timer obj c022c544! RTMP_TimerListAdd: add timer obj c022c128! RTMP_TimerListAdd: add timer obj c022c514! RTMP_TimerListAdd: add timer obj c022c860! RTMP_TimerListAdd: add timer obj c022c790! RTMP_TimerListAdd: add timer obj c022c7c0! RTMP_TimerListAdd: add timer obj c024e984! RTMP_TimerListAdd: add timer obj c024eaa0! RTMP_TimerListAdd: add timer obj c024e9b0! RTMP_TimerListAdd: add timer obj c0246134! E2pAccessMode=2 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 49 RTMP_TimerListAdd: add timer obj c02136a8! RTMP_TimerListAdd: add timer obj c021695c! RTMP_TimerListAdd: add timer obj c0219c10! RTMP_TimerListAdd: add timer obj c021cec4! RTMP_TimerListAdd: add timer obj c0220178! br0: port 2(ra0) entering forwarding state RTMP_TimerListAdd: add timer obj c022342c! RTMP_TimerListAdd: add timer obj c02266e0! RTMP_TimerListAdd: add timer obj c0229994! RTMP_TimerListAdd: add timer obj c0245e48! 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 TX0 power compensation = 0x38 TX1 power compensation = 0x38 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 UpdateChannelInfo: chan 0, false cca 452 UpdateChannelInfo: chan 0, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 UpdateChannelInfo: chan 1, false cca 248 UpdateChannelInfo: chan 1, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 UpdateChannelInfo: chan 2, false cca 1 UpdateChannelInfo: chan 2, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 UpdateChannelInfo: chan 3, false cca 57 UpdateChannelInfo: chan 3, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 30 mt76x2_single_sku::DefaultTargetPwr = 0x1e, delta_power = 0x0 UpdateChannelInfo: chan 4, false cca 26 UpdateChannelInfo: chan 4, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 30 mt76x2_single_sku::DefaultTargetPwr = 0x1e, delta_power = 0x0 UpdateChannelInfo: chan 5, false cca 2 UpdateChannelInfo: chan 5, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 30 mt76x2_single_sku::DefaultTargetPwr = 0x1e, delta_power = 0x0 UpdateChannelInfo: chan 6, false cca 2 UpdateChannelInfo: chan 6, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 30 mt76x2_single_sku::DefaultTargetPwr = 0x1e, delta_power = 0x0 UpdateChannelInfo: chan 7, false cca 0 UpdateChannelInfo: chan 7, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 8, false cca 466 UpdateChannelInfo: chan 8, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 9, false cca 2 UpdateChannelInfo: chan 9, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 10, false cca 27 UpdateChannelInfo: chan 10, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 11, false cca 13 UpdateChannelInfo: chan 11, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 12, false cca 260 UpdateChannelInfo: chan 12, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 13, false cca 0 UpdateChannelInfo: chan 13, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 14, false cca 1078 UpdateChannelInfo: chan 14, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 15, false cca 555 UpdateChannelInfo: chan 15, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 16, false cca 13 UpdateChannelInfo: chan 16, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 17, false cca 163 UpdateChannelInfo: chan 17, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 18, false cca 847 UpdateChannelInfo: chan 18, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 19, false cca 2157 UpdateChannelInfo: chan 19, BusyTime 0, duration 400 mt76x2_single_sku::DefaultTargetPwr = 29 mt76x2_single_sku::DefaultTargetPwr = 0x1d, delta_power = 0x0 UpdateChannelInfo: chan 20, false cca 864 UpdateChannelInfo: chan 20, BusyTime 0, duration 400 RTMP_TimerListAdd: add timer obj c0246424! mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=60, HT-CentCh=62, VHT-CentCh=58 mt76x2_single_sku::DefaultTargetPwr = 30 mt76x2_single_sku::DefaultTargetPwr = 0x1e, delta_power = 0x0 APStartUp(): AP Set CentralFreq at 58(Prim=60, HT-CentCh=62, VHT-CentCh=58, BBP_BW=2) mt76x2_calibration(channel = 58) Main bssid = 94:4a:0c:54:32:03 mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 original vga value(chain0) = 5c original vga value(chain1) = 5c <==== rt28xx_init, Status=0 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! device rai0 entered promiscuous mode br0: port 3(rai0) entering learning state br0: port 3(rai0) entering learning state ap_name=wlan_guest_portal, action=start ap_name=qtbl, action=start Insert quick routing module ... ######DUMP QUICK TABLE FUNC ADDR####### skb_dev_in_qtl:c3ee8138 CheckSumModify:c3ee7000 update_conntrack_time:c3ee77e0 matchFromLan:c3ee7818 matchFromWan:c3ee74fc doMatch:c3ee8524 MyCheckSum:c3ee7104 CheckSumDlt:c3ee714c checkEntry:c3ee7fd0 delEntry:c3ee73d8 addEntry:c3ee7e8c checkValidQTEntry:c3ee72f8 updateQtlWhenPktXmit:c3ee81bc qtbl_read_proc:c3ee7b7c qtbl_write_proc:c3ee7af8 ######DUMP QUICK TABLE FUNC ADDR END####### ap_name=hw_nat, action=start Ralink HW NAT Module Enabled ap_name=cron, action=start ap_name=networkmap, action=start sh: can't create /proc/sys/kernel/disable_kswapd: nonexistent directory nmap_main.c[nmap_wait_and_process_thread_func][437][57]:packet handle process pid 1688 nmap_main.c[nmap_wait_and_process_thread_func][437][57]:packet handle process pid 1687 nmap_main.c[nmap_wait_and_process_thread_func][437][57]:packet handle process pid 1690 nmap_main.c[nmap_wait_and_process_thread_func][437][57]:packet handle process pid 1689 nmap_main.c[nmap_wait_and_process_thread_func][437][57]:packet handle process pid 1691 nmap_main.c[nmap_detect_thread_func][381][57]:active detect process pid 1692 nmap_main.c[nmap_refresh_thread_func][393][57]:refresh process pid 1693 nmap_main.c[nmap_server_thread_func][446][57]:server process pid 1694 ap_name=switch, action=start ESW: Link Status Changed - Port2 Link Down br0: port 3(rai0) entering forwarding state ap_name=qos_service, action=start Init Ingress Classify module ... Change DHCP WAN match from <0> to <1> Change l2tp control match from <0> to <1> Change iptv packet classify from <0> to <1> Add dscp match from range idx=0,start_dscp=34,end_dscp=34 Change dscp match from <0> to <1> switch reg write offset=44, value=161117 switch reg write offset=2004, value=2ff0403 switch reg write offset=2104, value=2ff0403 switch reg write offset=2204, value=2ff0403 switch reg write offset=2304, value=2ff0403 switch reg write offset=2404, value=1ff0403 switch reg write offset=94, value=ffff06a5 switch reg write offset=98, value=c1000 switch reg write offset=90, value=80005000 switch reg write offset=94, value=80008000 switch reg write offset=98, value=d1000 switch reg write offset=90, value=80005001 switch reg write offset=94, value=3 switch reg write offset=98, value=0 switch reg write offset=90, value=80009000 switch reg write offset=94, value=f000070 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b000 switch reg write offset=94, value=ffffff03 switch reg write offset=98, value=d1008 switch reg write offset=90, value=80005002 switch reg write offset=94, value=ffffc021 switch reg write offset=98, value=d100a switch reg write offset=90, value=80005003 switch reg write offset=94, value=d switch reg write offset=98, value=0 switch reg write offset=90, value=80009001 switch reg write offset=94, value=f000070 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b001 switch reg write offset=94, value=1 switch reg write offset=98, value=0 switch reg write offset=90, value=80009002 switch reg write offset=94, value=b000030 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b002 switch reg write offset=94, value=8000800 switch reg write offset=98, value=8100c switch reg write offset=90, value=80005004 switch reg write offset=94, value=10 switch reg write offset=98, value=0 switch reg write offset=90, value=80009003 switch reg write offset=94, value=e000060 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b003 switch reg write offset=94, value=1000100 switch reg write offset=98, value=80f00 switch reg write offset=90, value=80005005 switch reg write offset=94, value=20 switch reg write offset=98, value=0 switch reg write offset=90, value=80009004 switch reg write offset=94, value=d000050 switch reg write offset=98, value=0 switch reg write offset=90, valuChange RxRingThrehold from <512> to <1024> e=8000b004 switch reg write offset=94, value=fc0088 switch reg write offset=98, value=a0f00 switch reg write offset=90, value=80005006 switch reg write offset=94, value=40 switch reg write offset=98, value=0 switch reg write offset=90, value=80009005 switch reg write offset=94, value=c000040 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b005 switch reg write offset=94, value=ffff944a switch reg write offset=98, value=80f00 switch reg write offset=90, value=80005007 switch reg write offset=94, value=ffff0c54 switch reg write offset=98, value=80f02 switch reg write offset=90, value=80005008 switch reg write offset=94, value=ffff3201 switch reg write offset=98, value=80f04 switch reg write offset=90, value=80005009 switch reg write offset=94, value=380 switch reg write offset=98, value=0 switch reg write offset=90, value=80009006 switch reg write offset=94, value=8000000 switch reg write offset=98, value=0 switch reg write offset=90, value=8000b006 switch reg write offset=1600, value=80008000 switch reg write offset=1604, value=80008437 switch reg write offset=1608, value=80000000 switch reg write offset=1610, value=80000000 switch reg write offset=1618, value=80000000 switch reg write offset=1620, value=80000000 switch reg write offset=1628, value=80000000 switch reg write offset=1630, value=80000000 switch reg write offset=1638, value=80000000 switch reg write offset=48, value=9080000 switch reg write offset=4c, value=1b581250 switch reg write offset=50, value=2da824a0 switch reg write offset=54, value=3ff836f0 Set: phy[0].reg[4] = 01e1 Set: phy[1].reg[4] = 01e1 Set: phy[2].reg[4] = 01e1 Set: phy[3].reg[4] = 01e1 Set: phy[4].reg[4] = 01e1 switch reg write offset=1fe0, value=20087864 ESW: Link Status Changed - Port2 Link UP nmap_active_detect.c[nmap_other_subnet_detect_func][595][58]:other subnet detect pid 1678 nmap_active_detect.c[nmap_other_subnet_detect_func][595][60]:other subnet detect pid 1678 nmap_active_detect.c[nmap_other_subnet_detect_func][595][71]:other subnet detect pid 1678 ~ # sc_cli Smart Box Pro login: SuperUser Password: Welcome to IAD2 CLI, you can type '?' to find usage view @ Smart Box Pro> show sysinfo Vendor: Sercomm Model: Smart Box Pro Firmware Version: v2.0.12 Build Time: 2014-12-09, 11:09:35 Hardware Version: v1 Bootloader Version: 4100 Serial Number: Time Since Last Boot: 0:05:45 Current Time: 1970-01-01 00:05:45


=================================================================== MT7621 stage1 code 10:40:45 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x0, 1/0 = 852/172 01000000 PLL2 FB_DL: 0xc, 1/0 = 565/459 31000000 PLL4 FB_DL: 0x16, 1/0 = 661/363 59000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 80 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00002322 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 7 11 8 7 7 9 5 6 6 10 | 9 9 7 9 7 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =34 DQS1 = 35 ================================================================== bit DQS0 bit DQS1 0 (1~66)33 8 (1~62)31 1 (1~66)33 9 (1~62)31 2 (1~68)34 10 (1~69)35 3 (1~66)33 11 (1~64)32 4 (1~67)34 12 (1~65)33 5 (1~67)34 13 (0~62)31 6 (1~65)33 14 (1~66)33 7 (1~67)34 15 (1~67)34 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 8 11 9 7 7 10 5 10 10 10 | 9 12 9 13 9 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Oct 17 2014 - 17:37:52) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffac000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 8ffe0cd0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 DA 90 95 44] Device not found, ID: c8da Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c8da select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 2047 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 Env addr : 0x800000 .*** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.0.6 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Oct 17 2014 Time:17:37:52 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN LLLLW ..Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000D cmd : 0x0000000D Press Ctrl+C to Enter the Main loop... 0 Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, boot Flash Sector Number : 2048. Bad block detected at 0x17640, oob_buf[0] is 0x0 NAND Section 9, has bad block at address c7b20000, Image Offset bb20000 NAND Section 9, has bad block count 1 *************************************************** Sercomm Boot Version 4.10.0 *************************************************** Entering Firmware : Everything is OK. Begin to verify the default image... kernel addr: 0x1700100 len: 0x29C2EC crc: 0xEAF95B23 ..........................................calculate_kernel_crc: 0xEAF95B23 ok! First image selected kernel addr :0xc1300100 kernel addr :0xC1300100 ## Booting image at c1300100 ... Image Name: MIPS OpenWrt Linux-5.10.120 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2736812 Bytes = 2.6 MB Load Address: 80001000 Entry Point: 80001000 .......................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK commandline in boot is : console=ttyS1,57600 ubi.mtd=7 root=ubi0:rootfs rw rootfstype=ubifs !!!! No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.10.120 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19426-2b1941e47d) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Jun 10 07:20:21 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Beeline SmartBox PRO [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30256 r8192 d22992 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00018008 [ 0.000000] Readback ErrCtl register=00018008 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 249352K/262144K available (6999K kernel code, 628K rwdata, 824K rodata, 1264K init, 244K bss, 12792K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000014] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015863] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033809] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106128] pid_max: default: 32768 minimum: 301 [ 0.115441] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129846] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.148145] rcu: Hierarchical SRCU implementation. [ 0.157959] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.173536] smp: Bringing up secondary CPUs ... [ 0.183285] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.183296] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.183309] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.183386] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.243376] Synchronize counters for CPU 1: done. [ 0.305590] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.305601] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.305610] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.305656] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.364530] Synchronize counters for CPU 2: done. [ 0.424869] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.424878] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.424887] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.424938] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.484107] Synchronize counters for CPU 3: done. [ 0.543718] smp: Brought up 1 node, 4 CPUs [ 0.556639] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.576152] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.589981] pinctrl core: initialized pinctrl subsystem [ 0.602720] NET: Registered protocol family 16 [ 0.612624] thermal_sys: Registered thermal governor 'step_wise' [ 0.614327] cpuidle: using governor teo [ 0.672262] clocksource: Switched to clocksource GIC [ 0.683612] NET: Registered protocol family 2 [ 0.692594] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.708034] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.724656] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.739846] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.753957] TCP: Hash tables configured (established 2048 bind 2048) [ 0.766711] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.779596] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.793741] NET: Registered protocol family 1 [ 0.802317] PCI: CLS 0 bytes, default 32 [ 0.812661] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.829511] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.841017] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.861321] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.877784] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.889191] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.900519] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.912555] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.929328] printk: console [ttyS0] disabled [ 0.937818] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.955739] printk: console [ttyS0] enabled [ 0.955739] printk: console [ttyS0] enabled [ 0.972291] printk: bootconsole [early0] disabled [ 0.972291] printk: bootconsole [early0] disabled [ 0.993693] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.008417] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xda [ 1.021075] nand: ESMT NAND 256MiB 3,3V 8-bit [ 1.029752] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.044831] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 1.057855] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.072415] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.086966] Scanning device for bad blocks [ 3.970018] Bad eraseblock 1497 at 0x00000bb20000 [ 5.035476] 16 fixed-partitions partitions found on MTD device mt7621-nand [ 5.049163] Creating 16 MTD partitions on "mt7621-nand": [ 5.059758] 0x000000000000-0x00000ff80000 : "ALL" [ 5.071157] 0x000000000000-0x000000100000 : "Bootloader" [ 5.083122] 0x000000100000-0x000000200000 : "Factory" [ 5.094497] 0x000000200000-0x000001600000 : "sys_data" [ 5.105816] 0x000001600000-0x000001700000 : "boot_flag" [ 5.117218] 0x000001700000-0x000001b00000 : "kernel" [ 5.128091] 0x000001b00000-0x000001f00000 : "Kernel_2" [ 5.139271] 0x000001f00000-0x000003d00000 : "RootFS_1" [ 5.150618] 0x000003d00000-0x000005b00000 : "RootFS_2" [ 5.161955] 0x000005b00000-0x000008d00000 : "JVM/OSGI1" [ 5.173656] 0x000008d00000-0x00000bf00000 : "JVM/OSGI2" [ 5.185243] 0x00000bf00000-0x00000fb00000 : "OSGI data" [ 5.196899] 0x00000fb00000-0x00000fc00000 : "Ftool" [ 5.207630] 0x000000800000-0x000000820000 : "BootLoad-Env" [ 5.219571] 0x000000200000-0x000000800000 : "sysdata01" [ 5.230974] 0x000000820000-0x000001600000 : "sysdata02" [ 5.252874] Concatenating MTD devices: [ 5.260384] (0): "RootFS_1" [ 5.265960] (1): "JVM/OSGI1" [ 5.271677] (2): "JVM/OSGI2" [ 5.277406] (3): "OSGI data" [ 5.283145] (4): "Ftool" [ 5.288170] (5): "sysdata01" [ 5.293908] (6): "sysdata02" [ 5.299624] into device "ubi-concat" [ 5.306792] 1 fixed-partitions partitions found on MTD device ubi-concat [ 5.320129] Creating 1 MTD partitions on "ubi-concat": [ 5.330365] 0x000000000000-0x00000d2e0000 : "ubi" [ 5.384498] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 5.400935] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 5.418366] i2c /dev entries driver [ 5.427887] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 5.441283] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 5.458810] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 5.475115] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 5.491497] mt7621-pci 1e140000.pcie: Parsing DT failed [ 5.504040] NET: Registered protocol family 10 [ 5.514670] Segment Routing with IPv6 [ 5.522054] NET: Registered protocol family 17 [ 5.531085] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 5.557333] 8021q: 802.1Q VLAN Support v1.8 [ 5.569057] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 5.606584] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26) [ 5.628678] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27) [ 5.650788] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28) [ 5.672981] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29) [ 5.695121] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30) [ 5.717356] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 5.734213] DSA: tree 0 setup [ 5.740432] rt2880-pinmux pinctrl: pcie is already enabled [ 5.751464] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 5.764895] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 5.782440] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 5.798745] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 5.815144] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 5.830227] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 5.845242] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 5.959897] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 5.971028] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 6.082382] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 6.096251] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 6.105968] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 6.115696] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 6.134407] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 6.147108] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 6.160812] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 6.174516] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.185456] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 6.205781] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 6.217778] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 6.230269] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff] [ 6.242833] pci 0000:00:00.0: supports D1 [ 6.250803] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 6.263073] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 6.275103] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 6.287599] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff] [ 6.300149] pci 0000:00:01.0: supports D1 [ 6.308140] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 6.321796] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 6.333857] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 6.347914] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 6.360438] pci 0000:01:00.0: reg 0x30: initial BAR value 0x00000000 invalid [ 6.374485] pci 0000:01:00.0: reg 0x30: [mem size 0x00010000 pref] [ 6.386912] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 6.401068] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 6.411529] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 6.423675] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 6.437206] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 6.451600] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.465071] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000 [ 6.477106] pci 0000:02:00.0: reg 0x10: [mem 0x60200000-0x602fffff 64bit] [ 6.490684] pci 0000:02:00.0: reg 0x30: initial BAR value 0x00000000 invalid [ 6.504741] pci 0000:02:00.0: reg 0x30: [mem size 0x00010000 pref] [ 6.517160] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 6.531346] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 6.541805] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 6.553953] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 6.567484] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 6.581878] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 6.595124] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 6.608306] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 6.622178] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 6.635368] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 6.649246] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 6.662783] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 6.677178] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 6.690704] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 6.705101] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 6.718637] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 6.732173] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 6.745705] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 6.759250] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 6.773828] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] [ 6.788230] pci 0000:00:00.0: PCI bridge to [bus 01] [ 6.798129] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 6.811659] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 6.825187] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 6.839589] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 6.854174] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] [ 6.868566] pci 0000:00:01.0: PCI bridge to [bus 02] [ 6.878464] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 6.891993] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 6.905521] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 6.922390] UBI: auto-attach mtd16 [ 6.929190] ubi0: attaching mtd16 [ 6.936182] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.987390] UBI: EOF marker found, PEBs from 33 will be erased [ 7.000682] ubi0: scanning is finished [ 7.053994] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 1619 LEBs [ 7.068241] ubi0: attached mtd16 (name "ubi", size 210 MiB) [ 7.079403] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.093101] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.106613] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.120470] ubi0: good PEBs: 1686, bad PEBs: 1, corrupted PEBs: 0 [ 7.132613] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 7.146991] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1654845621 [ 7.165177] ubi0: available PEBs: 0, total reserved PEBs: 1686, PEBs reserved for bad PEB handling: 32 [ 7.183746] ubi0: background thread "ubi_bgt0d" started, PID 493 [ 7.186277] block ubiblock0_0: created from ubi0:0(rootfs) [ 7.206804] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 7.259915] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 7.279205] Freeing unused kernel memory: 1264K [ 7.288269] This architecture does not have kernel memory protection. [ 7.301160] Run /sbin/init as init process [ 8.121869] init: Console is alive [ 8.129134] init: - watchdog - [ 9.334583] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 9.490995] usbcore: registered new interface driver usbfs [ 9.502425] usbcore: registered new interface driver hub [ 9.513412] usbcore: registered new device driver usb [ 9.538542] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 9.553945] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 9.569421] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 9.580083] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 9.602449] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 9.620831] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 9.633761] hub 1-0:1.0: USB hub found [ 9.641372] hub 1-0:1.0: 2 ports detected [ 9.650246] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 9.660954] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 9.675942] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 9.689017] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 9.706359] hub 2-0:1.0: USB hub found [ 9.714133] hub 2-0:1.0: 1 port detected [ 9.733606] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 9.752728] init: - preinit - [ 10.950836] random: jshn: uninitialized urandom read (4 bytes read) [ 11.038467] random: jshn: uninitialized urandom read (4 bytes read) [ 11.137104] random: jshn: uninitialized urandom read (4 bytes read) [ 11.644740] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 11.661428] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.661464] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 11.691858] 8021q: adding VLAN 0 to HW filter on device lan1 [ 11.705766] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 15.925104] UBIFS (ubi0:1): default file-system created [ 15.936900] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 15.948493] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 636 [ 16.077851] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 16.093496] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.113246] UBIFS (ubi0:1): FS size: 204050432 bytes (194 MiB, 1607 LEBs), journal size 10158080 bytes (9 MiB, 80 LEBs) [ 16.134726] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 16.147908] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 98CA5ADD-983A-4BD0-9AD8-D7FDD31B6390, small LPT model [ 16.173902] mount_root: overlay filesystem has not been fully initialized yet [ 16.188984] mount_root: switching to ubifs overlay [ 16.207218] urandom-seed: Seed file not found (/etc/urandom.seed) [ 16.327631] procd: - early - [ 16.333662] procd: - watchdog - [ 17.012484] procd: - watchdog - [ 17.125754] procd: - ubus - [ 17.269956] urandom_read_iter: 7 callbacks suppressed [ 17.269969] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.294775] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.307989] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.326931] procd: - init - Please press Enter to activate this console. [ 18.138340] kmodloader: loading kernel modules from /etc/modules.d/* [ 18.274541] urngd: v1.0.2 started. [ 18.446566] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 18.453500] random: crng init done [ 18.461713] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 18.468450] random: 23 urandom warning(s) missed due to ratelimiting [ 18.710189] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 18.721008] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 18.732302] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002) [ 18.744449] mt76x2e 0000:01:00.0: ASIC revision: 76120044 [ 19.412860] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a [ 19.429045] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 19.440008] mt76x2e 0000:01:00.0: Build: 1 [ 19.448175] mt76x2e 0000:01:00.0: Build Time: 201607111443____ [ 19.482281] mt76x2e 0000:01:00.0: Firmware running! [ 19.498233] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 19.509128] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 19.520691] mt76x2e 0000:02:00.0: ASIC revision: 76020044 [ 20.192330] mt76x2e 0000:02:00.0: ROM patch already applied [ 20.204326] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00 [ 20.215363] mt76x2e 0000:02:00.0: Build: 1 [ 20.223566] mt76x2e 0000:02:00.0: Build Time: 201607111443____ [ 20.238630] mt76x2e 0000:02:00.0: Firmware running! [ 20.304002] PPP generic driver version 2.4.2 [ 20.314386] NET: Registered protocol family 24 [ 20.331779] kmodloader: done loading kernel modules from /etc/modules.d/* [ 60.386836] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 60.409145] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 60.425504] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 60.429743] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 60.456104] 8021q: adding VLAN 0 to HW filter on device lan1 [ 60.470394] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 60.484061] br-lan: port 1(lan1) entered blocking state [ 60.494867] br-lan: port 1(lan1) entered disabled state [ 60.506683] device lan1 entered promiscuous mode [ 60.516322] device eth0 entered promiscuous mode [ 60.559896] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 60.573753] 8021q: adding VLAN 0 to HW filter on device lan2 [ 60.589038] br-lan: port 2(lan2) entered blocking state [ 60.599983] br-lan: port 2(lan2) entered disabled state [ 60.611856] device lan2 entered promiscuous mode [ 60.632731] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 60.646682] 8021q: adding VLAN 0 to HW filter on device lan3 [ 60.662642] br-lan: port 3(lan3) entered blocking state [ 60.673182] br-lan: port 3(lan3) entered disabled state [ 60.686484] device lan3 entered promiscuous mode [ 60.713260] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 60.727115] 8021q: adding VLAN 0 to HW filter on device lan4 [ 60.743213] br-lan: port 4(lan4) entered blocking state [ 60.753780] br-lan: port 4(lan4) entered disabled state [ 60.767468] device lan4 entered promiscuous mode [ 60.796721] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 60.810475] 8021q: adding VLAN 0 to HW filter on device wan [ 62.171465] mt7530 mdio-bus:1f lan2: Link is Up - 100Mbps/Full - flow control off [ 62.186601] br-lan: port 2(lan2) entered blocking state [ 62.197587] br-lan: port 2(lan2) entered forwarding state [ 62.211066] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.35.0 (2022-06-10 07:20:21 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 22.03.0-rc4, r19426-2b1941e47d ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/# ubus call system board { "kernel": "5.10.120", "hostname": "OpenWrt", "system": "MediaTek MT7621 ver:1 eco:3", "model": "Beeline SmartBox PRO", "board_name": "beeline,smartbox-pro", "rootfs_type": "squashfs", "release": { "distribution": "OpenWrt", "version": "22.03.0-rc4", "revision": "r19426-2b1941e47d", "target": "ramips/mt7621", "description": "OpenWrt 22.03.0-rc4 r19426-2b1941e47d" } }


Subnamespaces:

No subnamespaces.

Pages in this namespace:

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1