AVM FRITZ!Box 7312

(05.03.2019)

  • Boot: working
  • Serial Port: working
  • Wifi: working (disabled by default) → press WLan button or via ssh: uci set wireless.radio0.disabled='0' → uci commit
  • DHCP: working
  • Ethernet: working
  • ADSL: should be working, tested @TestBuild (AnnexB ATM & PTM) → default: Annex A not enabled in Kernel
  • LEDs: working, “red_info_LED” does not exist
  • LuCI: flash firmware working
  • SMP: working → bootlogs

→ TestBuild: Ethernet working, ADSL-Uplink has to be configuredFritzBox7312 Freifunk Berlin LEDE 1.0.0-olsrd0903-alpha, 04.09.2017, further info

To install OpenWrt via Eva bootloader, within the first seconds after power on an ftp connection needs to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
  ftp> quote REBOOT

Please mind that this instruction requests the sysupgrade image to be flashed to mtd1, not the initramfs image!

See fritzflash

from the linked page https://fritz-tools.readthedocs.io/en/latest/flashing/general.html#selecting-the-right-image:

Selecting the right Image
Gluon builds by default factory and sysupgrade images. AVM devices don’t need special factory-images, so most of them are flashed via the sysupgrade images.

→ use the sysupgrade image

Architecture MIPS
Vendor Lantiq
bootloader Adam2
System-On-Chip Lantiq Xway ARX188 PSB 50812 EL (MIPS 34Kc)
CPU/Speed 2×393 MHz
NOR Flash Macronix MX29GL128EHT2I-90G, 16MiB
RAM Chip Zentel A4S12D40FTP-G5
RAM Specs DDR1 64MiB @ 196 MHz
Wireless Atheros AR9227 b/g/n 2×2
Ethernet 1x 10/100 Atheros AR8030-A
Switch none (only 1 ethernet port available)
xDSL lantiq ADSL2+
USB no
DECT dialog semiconductor SC14441
Serial Yes (2.54mm, unpopulated)
GPIO Buttons wifi rfkill, dect rfkill
Power External 5V 1.6A

Towards the back of the device there are two (one on each side) plastic latches.
Those are accessible through the ventilation slots:

Use a thin tool (screw driver or similar) to push them towards the inside of the device.
Once you push it far enough you can open the case a little on one side, then do the same on the other side → the two parts of the case will “fall apart” on their own.

port.serial general information about the serial port, serial port cable, etc.

serial mode: 115200,n,8,1,hw

How to connect to the Serial Port of this specific device:

3V3 RX TX GND Software (Linux)
Board square circle circle circle
Siemens Data Cable white blue black sudo screen /dev/ttyUSB0 115200
Cutecom: Rate: 115200, Flow: none, Data: 8, Stop: 1, Parity: none → no input @BoxFTPMode → use screen

backup via FTP did work once for: “(AVM) EVA Revision: 1.1820 Version: 2820” → FritzBox7112 backup Firmware

after flashing different Firmware now it does not any more o.O → use tftp

[ 0.000000] Linux version 5.4.90 (human@rechenknecht58) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r15160+17-588933ae9a)) #0 SMP Sat Jul 25 12:26:32 2020 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is AVM FRITZ!Box 7320 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] Normal zone: 144 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] percpu: Embedded 14 pages/cpu s26192 r8192 d22960 u57344 [ 0.000000] pcpu-alloc: s26192 r8192 d22960 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=00040a04 [ 0.000000] Readback ErrCtl register=00040a04 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 56928K/65536K available (5490K kernel code, 210K rwdata, 624K rodata, 1276K init, 203K bss, 8608K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from 0x80631a0c with crng_init=0 [ 0.000000] CPU Clock: 393MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9721189849 ns [ 0.000014] sched_clock: 32 bits at 196MHz, resolution 5ns, wraps every 10922685437ns [ 0.007993] Calibrating delay loop... 260.86 BogoMIPS (lpj=521728) [ 0.046069] pid_max: default: 32768 minimum: 301 [ 0.051082] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.058312] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.070827] rcu: Hierarchical SRCU implementation. [ 0.076713] smp: Bringing up secondary CPUs ... [ 0.082874] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.082896] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.083019] CPU1 revision is: 0001954c (MIPS 34Kc) [ 0.121466] Synchronize counters for CPU 1: done. [ 0.145679] smp: Brought up 1 node, 2 CPUs [ 0.156381] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.166100] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.173090] pinctrl core: initialized pinctrl subsystem [ 0.181235] NET: Registered protocol family 16 [ 0.187954] FPU Affinity set after 2096 emulations [ 0.203019] pinctrl-xway 1e100b10.pinmux: Init done [ 0.211566] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20 [ 0.224450] PCI host bridge /fpi@10000000/pci@e105400 ranges: [ 0.230141] MEM 0x0000000018000000..0x0000000019ffffff [ 0.235397] IO 0x000000001ae00000..0x000000001affffff [ 0.298099] usbcore: registered new interface driver usbfs [ 0.303897] usbcore: registered new interface driver hub [ 0.309368] usbcore: registered new device driver usb [ 0.315569] PCI host bridge to bus 0000:00 [ 0.319630] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.326541] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.333461] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.340328] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.349595] pci 0000:00:0e.0: [168c:ff1d] type 00 class 0x020000 [ 0.355593] pci 0000:00:0e.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 0.364247] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.370798] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 0.377856] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.391949] clocksource: Switched to clocksource MIPS [ 0.400711] NET: Registered protocol family 2 [ 0.406824] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.415183] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.422871] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.429974] TCP: Hash tables configured (established 1024 bind 1024) [ 0.436676] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.443197] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.450633] NET: Registered protocol family 1 [ 0.455047] PCI: CLS 0 bytes, default 32 [ 0.460109] gptu: totally 6 16-bit timers/counters [ 0.465021] gptu: misc_register on minor 63 [ 0.469195] gptu: succeeded to request irq 126 [ 0.473725] gptu: succeeded to request irq 127 [ 0.478222] gptu: succeeded to request irq 128 [ 0.482744] gptu: succeeded to request irq 129 [ 0.487236] gptu: succeeded to request irq 130 [ 0.491770] gptu: succeeded to request irq 131 [ 0.499430] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.510687] random: fast init done [ 0.533832] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.539615] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.566652] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.575605] printk: console [ttyLTQ0] enabled [ 0.584225] printk: bootconsole [early0] disabled [ 0.598042] lantiq nor flash device: 01000000 at 10000000 [ 0.602297] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.611543] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.616666] Amd/Fujitsu Extended Query version 1.3. [ 0.621592] number of CFI chips: 1 [ 0.625050] 4 fixed-partitions partitions found on MTD device ltq_nor [ 0.631337] Creating 4 MTD partitions on "ltq_nor": [ 0.636194] 0x000000000000-0x000000020000 : "urlader" [ 0.644531] 0x000000020000-0x000000f80000 : "firmware" [ 0.694020] 2 eva-fw partitions found on MTD device firmware [ 0.698257] 0x000000020000-0x000000226385 : "kernel" [ 0.706285] 0x000000230100-0x000000f80000 : "rootfs" [ 0.713002] mtd: device 3 (rootfs) set to be root filesystem [ 0.717329] 1 squashfs-split partitions found on MTD device rootfs [ 0.723389] 0x000000760000-0x000000f80000 : "rootfs_data" [ 0.731747] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.738697] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 0.751333] libphy: Fixed MDIO Bus: probed [ 0.762106] libphy: ltq_mii: probed [ 0.764634] Generic PHY 1e180000.etop-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1e180000.etop-ffffffff:00, irq=POLL) [ 0.790232] NET: Registered protocol family 10 [ 0.798261] Segment Routing with IPv6 [ 0.800902] NET: Registered protocol family 17 [ 0.805056] 8021q: 802.1Q VLAN Support v1.8 [ 0.815527] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed [ 0.833675] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.841866] Freeing unused kernel memory: 1276K [ 0.844999] This architecture does not have kernel memory protection. [ 0.851345] Run /sbin/init as init process [ 2.341744] init: Console is alive [ 2.344328] init: - watchdog - [ 5.081604] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.160959] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator [ 5.168206] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator [ 5.214585] dwc2 1e101000.usb: DWC OTG Controller [ 5.218050] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1 [ 5.224957] dwc2 1e101000.usb: irq 62, io mem 0x1e101000 [ 5.232780] hub 1-0:1.0: USB hub found [ 5.235328] hub 1-0:1.0: 1 port detected [ 5.241456] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator [ 5.248527] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator [ 5.296218] dwc2 1e106000.usb: DWC OTG Controller [ 5.299543] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2 [ 5.306574] dwc2 1e106000.usb: irq 91, io mem 0x1e106000 [ 5.314309] hub 2-0:1.0: USB hub found [ 5.316942] hub 2-0:1.0: 1 port detected [ 5.324874] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.333381] init: - preinit - [ 7.542907] random: procd: uninitialized urandom read (4 bytes read) [ 11.616118] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.125290] jffs2: notice: (518) jffs2_build_xattr_subsystem: complete building xattr subsystem, 16 of xdatum (12 unchecked, 1 orphan) and 21 of xref (1 dead, 0 orphan) found. [ 12.143414] mount_root: switching to jffs2 overlay [ 12.161779] overlayfs: upper fs does not support tmpfile. [ 12.180902] urandom-seed: Seeding with /etc/urandom.seed [ 12.552994] procd: - early - [ 12.554665] procd: - watchdog - [ 13.263180] procd: - watchdog - [ 13.267438] procd: - ubus - [ 13.391380] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.401495] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.407292] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.415575] procd: - init - [ 15.045291] kmodloader: loading kernel modules from /etc/modules.d/* [ 15.127788] NET: Registered protocol family 8 [ 15.130767] NET: Registered protocol family 20 [ 15.157690] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 15.192053] PPP generic driver version 2.4.2 [ 15.469325] IFX MEI Version 5.00.00 [ 15.500677] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 [ 15.516306] Mirror/redirect action on [ 15.566776] u32 classifier [ 15.568256] input device check on [ 15.571689] Actions configured [ 15.673552] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1 [ 15.679751] Backport generated by backports.git v5.8.18-1-0-ga630fd46 [ 15.847322] urngd: v1.0.2 started. [ 15.996456] Infineon Technologies DEU driver version 2.0.0 [ 16.168336] IFX DEU DES initialized (multiblock). [ 16.192953] IFX DEU AES initialized (multiblock). [ 16.209105] IFX DEU ARC4 initialized (multiblock). [ 16.216352] IFX DEU SHA1 initialized. [ 16.224370] IFX DEU MD5 initialized. [ 16.232364] IFX DEU SHA1_HMAC initialized. [ 16.235713] IFX DEU MD5_HMAC initialized. [ 16.306121] NET: Registered protocol family 24 [ 16.421576] xt_time: kernel timezone is -0000 [ 16.428488] ath9k_pci_owl_loader 0000:00:0e.0: enabling device (0000 -> 0002) [ 16.454254] ath9k_pci_owl_loader 0000:00:0e.0: fixup device configuration [ 16.513969] pci 0000:00:0e.0: [168c:002d] type 00 class 0x028000 [ 16.518769] pci 0000:00:0e.0: reg 0x10: [mem 0x18000000-0x1800ffff] [ 16.525024] pci 0000:00:0e.0: PME# supported from D0 D3hot [ 16.533601] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 16.596938] random: crng init done [ 16.598883] random: 6 urandom warning(s) missed due to ratelimiting [ 16.703781] batman_adv: B.A.T.M.A.N. advanced 2020.4-openwrt-1 (compatibility version 15) loaded [ 16.733990] ath9k 0000:00:0e.0: enabling device (0000 -> 0002) [ 16.748083] ath: EEPROM regdomain: 0x8114 [ 16.748103] ath: EEPROM indicates we should expect a country code [ 16.748119] ath: doing EEPROM country->regdmn map search [ 16.748132] ath: country maps to regdmn code: 0x37 [ 16.748146] ath: Country alpha2 being used: DE [ 16.748156] ath: Regpair used: 0x37 [ 16.772828] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.779387] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30 [ 16.790181] kmodloader: done loading kernel modules from /etc/modules.d/* [ 42.790452] br-dhcp: port 1(eth0) entered blocking state [ 42.794474] br-dhcp: port 1(eth0) entered disabled state [ 42.800805] device eth0 entered promiscuous mode [ 43.354055] IPv6: ADDRCONF(NETDEV_CHANGE): ffuplink: link becomes ready [ 43.368070] br-wan: port 1(ffuplink_wan) entered blocking state [ 43.372636] br-wan: port 1(ffuplink_wan) entered disabled state [ 43.379762] device ffuplink_wan entered promiscuous mode [ 43.404555] br-wan: port 1(ffuplink_wan) entered blocking state [ 43.409118] br-wan: port 1(ffuplink_wan) entered forwarding state [ 45.856545] br-dhcp: port 1(eth0) entered blocking state [ 45.860509] br-dhcp: port 1(eth0) entered forwarding state [ 45.876121] IPv6: ADDRCONF(NETDEV_CHANGE): br-dhcp: link becomes ready [ 49.804964] br-dhcp: port 2(wlan0-dhcp-2) entered blocking state [ 49.809671] br-dhcp: port 2(wlan0-dhcp-2) entered disabled state [ 49.816740] device wlan0-dhcp-2 entered promiscuous mode [ 49.916114] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-dhcp-2: link becomes ready [ 49.922491] br-dhcp: port 2(wlan0-dhcp-2) entered blocking state [ 49.927746] br-dhcp: port 2(wlan0-dhcp-2) entered forwarding state [ 54.012025] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-mesh-2: link becomes ready [ 167.313747] br-wan: port 1(ffuplink_wan) entered disabled state [ 167.348741] device ffuplink_wan left promiscuous mode [ 167.352895] br-wan: port 1(ffuplink_wan) entered disabled state BusyBox v1.31.1 () built-in shell (ash) _____ _ __ _ | ___| (_)/ _| | | | |_ _ __ ___ _| |_ _ _ _ __ | | __ | _| '__/ _ \ | _| | | | '_ \| |/ / | | | | | __/ | | | |_| | | | | < \_| |_| \___|_|_| \__,_|_| |_|_|\_\ Firmware Freifunk Berlin (SAm0815-Next-nightly rev e5a6ba97) Generic - lantiq/xway https://wiki.freifunk.net/Berlin:Firmware https://github.com/freifunk-berlin ----------------------------------------------------- If you find bugs please report them at: https://github.com/freifunk-berlin/firmware/issues For questions write a mail to <berlin@berlin.freifunk.net> or check https://berlin.freifunk.net/contact for our weekly meetings. root@:~#


Linux 4.14 SMP

[ 0.000000] Linux version 4.14.103 (human@rechenknecht15) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9433-f20fea9)) #0 SMP Mon Feb 25 16:33:16 2019 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is AVM FRITZ!Box 7312 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80588020, node_mem_map 81007b20 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from 0x8058b73c with crng_init=0 [ 0.000000] percpu: Embedded 14 pages/cpu @8108a000 s26800 r8192 d22352 u57344 [ 0.000000] pcpu-alloc: s26800 r8192 d22352 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0006008f [ 0.000000] Readback ErrCtl register=0006008f [ 0.000000] Memory: 57652K/65536K available (4945K kernel code, 186K rwdata, 528K rodata, 1236K init, 214K bss, 7884K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 393MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9721189849 ns [ 0.000014] sched_clock: 32 bits at 196MHz, resolution 5ns, wraps every 10922685437ns [ 0.008012] Calibrating delay loop... 260.86 BogoMIPS (lpj=521728) [ 0.046108] pid_max: default: 32768 minimum: 301 [ 0.051079] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057618] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.067735] Hierarchical SRCU implementation. [ 0.073671] smp: Bringing up secondary CPUs ... [ 0.079555] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.079573] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.079733] CPU1 revision is: 0001954c (MIPS 34Kc) [ 0.118421] Synchronize counters for CPU 1: done. [ 0.142559] smp: Brought up 1 node, 2 CPUs [ 0.151951] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.161677] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.167926] pinctrl core: initialized pinctrl subsystem [ 0.176052] NET: Registered protocol family 16 [ 0.184694] cpuidle: using governor ladder [ 0.199948] pinctrl-xway 1e100b10.pinmux: Init done [ 0.207167] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20 [ 0.219965] Can't analyze schedule() prologue at 804cf548 [ 0.225355] FPU Affinity set after 2096 emulations [ 0.227495] PCI host bridge /fpi@10000000/pci@e105400 ranges: [ 0.233536] MEM 0x0000000018000000..0x0000000019ffffff [ 0.238670] IO 0x000000001ae00000..0x000000001affffff [ 0.280727] usbcore: registered new interface driver usbfs [ 0.286565] usbcore: registered new interface driver hub [ 0.292053] usbcore: registered new device driver usb [ 0.298078] PCI host bridge to bus 0000:00 [ 0.302113] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.309023] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.315976] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.322832] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.330916] pci 0000:00:0e.0: [168c:ff1d] type 00 class 0x020000 [ 0.330990] pci 0000:00:0e.0: reg 0x10: [mem 0x00000000-0x0000ffff] [ 0.331647] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.331733] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 0.340536] clocksource: Switched to clocksource MIPS [ 0.350060] NET: Registered protocol family 2 [ 0.355856] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.362791] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.369199] TCP: Hash tables configured (established 1024 bind 1024) [ 0.375866] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.381657] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.388365] NET: Registered protocol family 1 [ 0.392767] PCI: CLS 0 bytes, default 32 [ 0.393788] gptu: totally 6 16-bit timers/counters [ 0.399008] gptu: misc_register on minor 63 [ 0.403220] gptu: succeeded to request irq 126 [ 0.407745] gptu: succeeded to request irq 127 [ 0.412224] gptu: succeeded to request irq 128 [ 0.416753] gptu: succeeded to request irq 129 [ 0.421285] gptu: succeeded to request irq 130 [ 0.425769] gptu: succeeded to request irq 131 [ 0.430493] No VPEs reserved for AP/SP, not initialize VPE loader [ 0.430493] Pass maxvpes=<n> argument as kernel argument [ 0.441904] No TCs reserved for AP/SP, not initializing RTLX. [ 0.441904] Pass maxtcs=<n> argument as kernel argument [ 0.455788] Crashlog allocated RAM at address 0x3f00000 [ 0.461621] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.485179] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.490997] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.505513] random: fast init done [ 0.515190] io scheduler noop registered [ 0.519095] io scheduler deadline registered (default) [ 0.528145] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.537169] console [ttyLTQ0] enabled [ 0.544394] bootconsole [early0] disabled [ 0.554158] cacheinfo: Failed to find cpu0 device node [ 0.557974] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.565357] lantiq nor flash device: 01000000 at 10000000 [ 0.569603] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.578838] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.583953] Amd/Fujitsu Extended Query version 1.3. [ 0.588934] number of CFI chips: 1 [ 0.592299] 4 fixed-partitions partitions found on MTD device ltq_nor [ 0.598677] Creating 4 MTD partitions on "ltq_nor": [ 0.603498] 0x000000000000-0x000000020000 : "urlader" [ 0.611242] 0x000000020000-0x000000f80000 : "firmware" [ 0.654668] 2 eva-fw partitions found on MTD device firmware [ 0.658928] 0x000000020000-0x0000001ddacf : "kernel" [ 0.666574] 0x0000001e0100-0x000000f80000 : "rootfs" [ 0.672843] mtd: device 3 (rootfs) set to be root filesystem [ 0.677207] 1 squashfs-split partitions found on MTD device rootfs [ 0.683246] 0x000000620000-0x000000f80000 : "rootfs_data" [ 0.691155] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.697661] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 0.710552] libphy: Fixed MDIO Bus: probed [ 0.715059] libphy: ltq_mii: probed [ 0.792792] Atheros 8030 ethernet 1e180000.etop-ffffffff:00: attached PHY driver [Atheros 8030 ethernet] (mii_bus:phy_addr=1e180000.etop-ffffffff:00, irq=POLL) [ 0.809871] wdt 1f8803f0.watchdog: Init done [ 0.820558] NET: Registered protocol family 10 [ 0.826582] Segment Routing with IPv6 [ 0.829119] NET: Registered protocol family 17 [ 0.833359] 8021q: 802.1Q VLAN Support v1.8 [ 0.844827] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed [ 0.863730] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.871711] Freeing unused kernel memory: 1236K [ 0.874898] This architecture does not have kernel memory protection. [ 2.389634] init: Console is alive [ 2.392076] init: - watchdog - [ 4.639193] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.737245] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.744859] init: - preinit - [ 6.028973] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.057135] random: procd: uninitialized urandom read (4 bytes read) [ 9.753297] jffs2: notice: (426) jffs2_build_xattr_subsystem: complete building xattr subsystem, 5 of xdatum (0 unchecked, 3 orphan) and 8 of xref (3 dead, 0 orphan) found. [ 9.771178] mount_root: switching to jffs2 overlay [ 9.828234] overlayfs: upper fs does not support tmpfile. [ 9.846389] urandom-seed: Seeding with /etc/urandom.seed [ 10.068785] procd: - early - [ 10.070457] procd: - watchdog - [ 10.788376] procd: - watchdog - [ 10.790914] procd: - ubus - [ 11.031907] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.041302] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.047055] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.056197] procd: - init - [ 11.858956] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.873909] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 11.900112] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.946940] u32 classifier [ 11.948275] input device check on [ 11.952073] Actions configured [ 11.960210] Mirror/redirect action on [ 11.983001] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 12.015859] Loading modules backported from Linux version v4.19.23-0-g67d52fae61c1 [ 12.022041] Backport generated by backports.git v4.19.23-1-0-g480a925a [ 12.036268] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.064906] Infineon Technologies DEU driver version 2.0.0 [ 12.081879] IFX DEU DES initialized (multiblock). [ 12.090206] IFX DEU AES initialized (multiblock). [ 12.095017] IFX DEU ARC4 initialized (multiblock). [ 12.099258] IFX DEU SHA1 initialized. [ 12.102633] IFX DEU MD5 initialized. [ 12.106392] IFX DEU SHA1_HMAC initialized. [ 12.110462] IFX DEU MD5_HMAC initialized. [ 12.220832] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 12.235147] owl-loader 0000:00:0e.0: fixup device configuration [ 12.243201] pci 0000:00:0e.0: [168c:002d] type 00 class 0x028000 [ 12.243309] pci 0000:00:0e.0: reg 0x10: [mem 0x18000000-0x1800ffff] [ 12.243528] pci 0000:00:0e.0: PME# supported from D0 D3hot [ 12.244424] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 12.335860] xt_time: kernel timezone is -0000 [ 12.525929] batman_adv: B.A.T.M.A.N. advanced openwrt-2019.0-0 (compatibility version 15) loaded [ 12.555269] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 12.569533] ath: EEPROM regdomain: 0x8114 [ 12.569553] ath: EEPROM indicates we should expect a country code [ 12.569568] ath: doing EEPROM country->regdmn map search [ 12.569581] ath: country maps to regdmn code: 0x37 [ 12.569597] ath: Country alpha2 being used: DE [ 12.569608] ath: Regpair used: 0x37 [ 12.596132] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 12.603519] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30 [ 12.616195] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.424693] urandom_read: 5 callbacks suppressed [ 15.424709] random: jshn: uninitialized urandom read (4 bytes read) [ 18.740684] random: crng init done [ 31.158760] br-dhcp: port 1(eth0) entered blocking state [ 31.162857] br-dhcp: port 1(eth0) entered disabled state [ 31.169069] device eth0 entered promiscuous mode [ 31.198328] br-dhcp: port 1(eth0) entered blocking state [ 31.202345] br-dhcp: port 1(eth0) entered forwarding state [ 31.208666] IPv6: ADDRCONF(NETDEV_UP): br-dhcp: link is not ready [ 31.558876] IPv6: ADDRCONF(NETDEV_UP): ffuplink: link is not ready [ 31.694498] IPv6: ADDRCONF(NETDEV_CHANGE): ffuplink: link becomes ready [ 31.704645] br-wan: port 1(ffuplink_wan) entered blocking state [ 31.709243] br-wan: port 1(ffuplink_wan) entered disabled state [ 31.716190] device ffuplink_wan entered promiscuous mode [ 31.757132] br-wan: port 1(ffuplink_wan) entered blocking state [ 31.761697] br-wan: port 1(ffuplink_wan) entered forwarding state [ 32.144699] IPv6: ADDRCONF(NETDEV_CHANGE): br-dhcp: link becomes ready [ 37.897464] IPv6: ADDRCONF(NETDEV_UP): wlan0-dhcp-2: link is not ready [ 37.928246] br-dhcp: port 2(wlan0-dhcp-2) entered blocking state [ 37.932901] br-dhcp: port 2(wlan0-dhcp-2) entered disabled state [ 37.939873] device wlan0-dhcp-2 entered promiscuous mode [ 38.013504] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-dhcp-2: link becomes ready [ 38.019800] br-dhcp: port 2(wlan0-dhcp-2) entered blocking state [ 38.025144] br-dhcp: port 2(wlan0-dhcp-2) entered forwarding state [ 38.566970] IPv6: ADDRCONF(NETDEV_UP): wlan0-adhoc-2: link is not ready [ 38.660029] wlan0-adhoc-2: Created IBSS using preconfigured BSSID d2:ca:ff:ee:ba:be [ 38.666367] wlan0-adhoc-2: Creating new IBSS network, BSSID d2:ca:ff:ee:ba:be [ 38.675238] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-adhoc-2: link becomes ready BusyBox v1.30.1 () built-in shell (ash) _____ _ __ _ | ___| (_)/ _| | | | |_ _ __ ___ _| |_ _ _ _ __ | | __ | _| '__/ _ \ | _| | | | '_ \| |/ / | | | | | __/ | | | |_| | | | | < \_| |_| \___|_|_| \__,_|_| |_|_|\_\ Firmware Freifunk Berlin (Dev-daily rev 6b8eb95) Generic - lantiq/xway https://wiki.freifunk.net/Berlin:Firmware https://github.com/freifunk-berlin ----------------------------------------------------- If you find bugs please report them at: https://github.com/freifunk-berlin/firmware/issues For questions write a mail to <berlin@berlin.freifunk.net> or check https://berlin.freifunk.net/contact for our weekly meetings. root@:~# lscpu Architecture: mips Byte Order: Big Endian CPU(s): 2 On-line CPU(s) list: 0,1 Thread(s) per core: 2 Core(s) per socket: 1 Socket(s): 1 BogoMIPS: 260.86 root@cottbus-sand-1:~# cat /proc/cpuinfo system type : AR9 rev 1.2 machine : AVM FRITZ!Box 7312 processor : 0 cpu model : MIPS 34Kc V4.12 BogoMIPS : 260.86 wait instruction : yes microsecond timers : yes tlb_entries : 16 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] isa : mips1 mips2 mips32r1 mips32r2 ASEs implemented : mips16 dsp mt Options implemented : tlb 4kex 4k_cache prefetch mcheck ejtag llsc vint perf_cntr_intr_bit nan_legacy nan_2008 perf shadow register sets : 1 kscratch registers : 0 package : 0 core : 0 VPE : 0 VCED exceptions : not available VCEI exceptions : not available processor : 1 cpu model : MIPS 34Kc V4.12 BogoMIPS : 262.14 wait instruction : yes microsecond timers : yes tlb_entries : 16 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] isa : mips1 mips2 mips32r1 mips32r2 ASEs implemented : mips16 dsp mt Options implemented : tlb 4kex 4k_cache prefetch mcheck ejtag llsc vint perf_cntr_intr_bit nan_legacy nan_2008 perf shadow register sets : 1 kscratch registers : 0 package : 0 core : 0 VPE : 1 VCED exceptions : not available VCEI exceptions : not available root@cottbus-sand-1:~# top Mem: 32416K used, 26472K free, 524K shrd, 3664K buff, 10492K cached CPU0: 0% usr 2% sys 0% nic 96% idle 0% io 0% irq 0% sirq CPU1: 0% usr 1% sys 0% nic 98% idle 0% io 0% irq 0% sirq Load average: 0.03 0.19 0.15 3/65 3548 PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND 3548 3396 root R 1200 2% 0 1% top 2713 1 root S 1988 3% 0 0% /usr/sbin/olsrd -f /var/etc/olsrd.conf -nofork 2073 1 dnsmasq S 1328 2% 1 0% /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c -k -x /var/run/dnsmasq/dnsmasq.c 1970 1 root S 1736 3% 0 0% /usr/sbin/hostapd -s -P /var/run/wifi-phy0.pid -B /var/run/hostapd-phy0.conf 2845 1 root S 1652 3% 1 0% /usr/sbin/olsrd -f /var/etc/olsrd6.conf -nofork 8 2 root IW 0 0% 1 0% [rcu_sched] 3184 1128 root S 1128 2% 1 0% /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300 -T 3 5 2 root IW 0 0% 1 0% [kworker/u4:0] 3 2 root IW 0 0% 0 0% [kworker/0:0] 88 2 root IW 0 0% 1 0% [kworker/u4:2] 3002 1 root SN 4652 8% 1 0% /usr/sbin/collectd -f 2576 1 root S 2184 4% 0 0% /usr/sbin/uhttpd -f -h /www -r cottbus-sand-1 -x /cgi-bin -u /ubus -t 60 -T 30 -k 20 1185 1 root S 1744 3% 1 0% /sbin/netifd 1 0 root S 1540 3% 0 0% /sbin/procd 1024 1 root S 1460 2% 1 0% /sbin/rpcd -s /var/run/ubus.sock -t 30 1216 1 root S 1432 2% 0 0% /usr/sbin/odhcpd 1005 1 root S 1232 2% 0 0% /sbin/logd -S 64 476 1 root S 1208 2% 0 0% /sbin/ubusd 3396 3184 root S 1204 2% 1 0% -ash [...]


Lede 17.01.x Freifunk

Firmware Berlin (Hedy 1.0.0-alpha rev 9e7deaf)modified → Wireless & Lan workin

(AVM) EVA Revision: 1.1820 Version: 2820 (C) Copyright 2005 AVM Date: Jul 16 2013 Time: 15:30:34 (1) 3 0x90000909-0x9000BD1F [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz Atheros 8030 detected Eva_AVM >...................................[ 0.000000] Linux version 4.4.83 (human@rechenknecht15) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3316-7eb58cf109) ) #0 Thu Aug 17 17:47:27 2017 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is FRITZ7320 - 1&1 HomeServer [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=000462c2 [ 0.000000] Readback ErrCtl register=000462c2 [ 0.000000] Memory: 59252K/65536K available (3587K kernel code, 153K rwdata, 448K rodata, 1236K init, 199K bss, 6284K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 393MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9721189849 ns [ 0.000013] sched_clock: 32 bits at 196MHz, resolution 5ns, wraps every 10922685437ns [ 0.007940] Calibrating delay loop... 260.86 BogoMIPS (lpj=521728) [ 0.042394] pid_max: default: 32768 minimum: 301 [ 0.047265] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053804] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.066706] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.076363] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.082573] pinctrl core: initialized pinctrl subsystem [ 0.088674] NET: Registered protocol family 16 [ 0.097714] pinctrl-xway 1e100b10.pinmux: Init done [ 0.103753] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20 [ 0.163311] Can't analyze schedule() prologue at 80008ef0 [ 0.178334] PCI host bridge /fpi@10000000/pci@E105400 ranges: [ 0.183996] MEM 0x0000000018000000..0x0000000019ffffff [ 0.189237] IO 0x000000001ae00000..0x000000001affffff [ 0.210882] usbcore: registered new interface driver usbfs [ 0.216403] usbcore: registered new interface driver hub [ 0.221766] usbcore: registered new device driver usb [ 0.227133] PCI host bridge to bus 0000:00 [ 0.231148] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.238044] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.244988] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.251843] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.260540] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 0.268286] clocksource: Switched to clocksource MIPS [ 0.274803] NET: Registered protocol family 2 [ 0.280225] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.287142] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.293510] TCP: Hash tables configured (established 1024 bind 1024) [ 0.300094] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.305871] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.312517] NET: Registered protocol family 1 [ 0.324175] gptu: totally 6 16-bit timers/counters [ 0.329053] gptu: misc_register on minor 63 [ 0.333152] gptu: succeeded to request irq 126 [ 0.337624] gptu: succeeded to request irq 127 [ 0.342136] gptu: succeeded to request irq 128 [ 0.346650] gptu: succeeded to request irq 129 [ 0.351164] gptu: succeeded to request irq 130 [ 0.355678] gptu: succeeded to request irq 131 [ 0.361301] Crashlog allocated RAM at address 0x3f00000 [ 0.390228] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.395963] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.410727] io scheduler noop registered [ 0.414552] io scheduler deadline registered (default) [ 0.420501] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.429414] console [ttyLTQ0] enabled [ 0.429414] console [ttyLTQ0] enabled [ 0.436672] bootconsole [early0] disabled [ 0.436672] bootconsole [early0] disabled [ 0.445703] lantiq nor flash device: 01000000 at 10000000 [ 0.449875] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.459155] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.464248] Amd/Fujitsu Extended Query version 1.3. [ 0.469230] number of CFI chips: 1 [ 0.472636] 4 ofpart partitions found on MTD device ltq_nor [ 0.478117] Creating 4 MTD partitions on "ltq_nor": [ 0.482945] 0x000000000000-0x000000020000 : "urlader" [ 0.491940] 0x000000020000-0x000000f80000 : "firmware" [ 0.535088] 2 eva-fw partitions found on MTD device firmware [ 0.539323] 0x000000020000-0x00000017c34c : "kernel" [ 0.546386] 0x000000180100-0x000000f80000 : "rootfs" [ 0.552550] mtd: device 3 (rootfs) set to be root filesystem [ 0.556846] 1 squashfs-split partitions found on MTD device rootfs [ 0.562885] 0x000000680000-0x000000f80000 : "rootfs_data" [ 0.570879] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.577224] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 0.592366] libphy: ltq_mii: probed [ 0.594653] eth0: attached PHY [Generic PHY] (phy_addr=1e180000.etop-ff:00, irq=-1) [ 0.603522] wdt 1f8803f0.watchdog: Init done [ 0.609712] NET: Registered protocol family 10 [ 0.619585] NET: Registered protocol family 17 [ 0.622745] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.635114] 8021q: 802.1Q VLAN Support v1.8 [ 0.639349] found entry name -> annex=B [ 0.643118] found entry name -> maca=34:31:C4:56:C9:3F [ 0.648141] found entry name -> macb=34:31:C4:56:C9:40 [ 0.653230] found entry name -> macwlan=34:31:C4:56:C9:41 [ 0.658577] found entry name -> macdsl=34:31:C4:56:C9:42 [ 0.663942] found entry name -> macwlan2=34:31:C4:56:C9:44 [ 0.669282] found entry name -> wlan_key=52492293968187462901 [ 0.681306] fdt: not creating '/sys/firmware/fdt': CRC check fai[ 0.699158] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.706980] Freeing unused kernel memory: 1236K [ 2.706171] init: Console is alive [ 2.708584] init: - watchdog - [ 4.980004] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.948555] dwc2 1e101000.ifxhcd: DWC OTG Controller [ 5.952120] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1 [ 5.959408] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000 [ 5.966486] hub 1-0:1.0: USB hub found [ 5.969407] hub 1-0:1.0: 1 port detected [ 5.974400] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.990793] init: - preinit - [ 6.919407] random: procd: uninitialized urandom read (4 bytes read, 28 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.346715] jffs2: notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 10.363881] mount_root: switching to jffs2 overlay [ 10.382332] urandom-seed: Seeding with /etc/urandom.seed [ 10.691911] procd: - early - [ 10.693634] procd: - watchdog - [ 11.394934] procd: - watchdog - [ 11.397263] procd: - ubus - [ 11.542158] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.550374] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.558692] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.571025] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.578669] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.587884] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.597321] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available) [ 11.605997] procd: - init - Please press Enter to activate this console. [ 12.155147] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.166413] NET: Registered protocol family 8 [ 12.169375] NET: Registered protocol family 20 [ 12.179350] tun: Universal TUN/TAP device driver, 1.6 [ 12.183006] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 12.196705] ipip: IPv4 over IPv4 tunneling driver [ 12.229201] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 12.256162] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 12.262747] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 12.376751] batman_adv: B.A.T.M.A.N. advanced 2016.5 (compatibility version 15) loaded [ 12.391142] IFX MEI Version 5.00.00 [ 12.410600] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 [ 12.456887] u32 classifier [ 12.458142] input device check on [ 12.461807] Actions configured [ 12.481421] Mirror/redirect action on [ 12.493958] nf_conntrack version 0.5.0 (945 buckets, 3780 max) [ 12.599009] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.622849] ATM1.0.26 ATM (A1) firmware version 0.16 [ 12.626672] ifxmips_atm: ATM init succeed [ 12.645211] Infineon Technologies DEU driver version 2.0.0 [ 12.672491] IFX DEU DES initialized (multiblock). [ 12.686236] IFX DEU AES initialized (multiblock). [ 12.704495] IFX DEU ARC4 initialized (multiblock). [ 12.708146] IFX DEU SHA1 initialized. [ 12.716547] IFX DEU MD5 initialized. [ 12.724528] IFX DEU SHA1_HMAC initialized. [ 12.730364] IFX DEU MD5_HMAC initialized. [ 12.835478] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 12.842697] owl-loader 0000:00:0e.0: fixup device configuration [ 12.849960] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 12.863965] random: ubusd: uninitialized urandom read (4 bytes read, 53 bits of entropy available) [ 12.881698] random: ubus: uninitialized urandom read (4 bytes read, 53 bits of entropy available) [ 12.948914] xt_time: kernel timezone is -0000 [ 13.006239] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 13.052501] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30 [ 13.092642] kmodloader: done loading kernel modules from /etc/modules.d/* [ 27.448155] device eth0 entered promiscuous mode [ 27.463014] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 28.691735] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready [ 29.264672] br-lan: port 1(eth0) entered forwarding state [ 29.268749] br-lan: port 1(eth0) entered forwarding state [ 29.288398] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 31.272354] br-lan: port 1(eth0) entered forwarding state [ 31.284396] random: nonblocking pool is initialized BusyBox v1.25.1 () built-in shell (ash) _____ _ __ _ | ___| (_)/ _| | | | |_ _ __ ___ _| |_ _ _ _ __ | | __ | _| '__/ _ \ | _| | | | '_ \| |/ / | | | | | __/ | | | |_| | | | | < \_| |_| \___|_|_| \__,_|_| |_|_|\_\ Firmware Berlin (Hedy 1.0.0-alpha rev 9e7deaf) Generic - lantiq/xway https://wiki.freifunk.net/Berlin:Firmware https://github.com/freifunk-berlin ----------------------------------------------------- If you find bugs please report them at: https://github.com/freifunk-berlin/firmware/issues For questions write a mail to <berlin@berlin.freifunk.net> or check https://berlin.freifunk.net/contact for our weekly meetings. === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@LEDE:/# ifconfig br-lan Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:192.168.42.1 Bcast:192.168.42.255 Mask:255.255.255.0 inet6 addr: fd6a:7cb0:e3f9::1/60 Scope:Global inet6 addr: fe80::3631:c4ff:fe56:c93f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:532 errors:0 dropped:0 overruns:0 frame:0 TX packets:375 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:50741 (49.5 KiB) TX bytes:35295 (34.4 KiB) eth0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:522 errors:0 dropped:0 overruns:0 frame:0 TX packets:391 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:56620 (55.2 KiB) TX bytes:37465 (36.5 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:232 errors:0 dropped:0 overruns:0 frame:0 TX packets:232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:15012 (14.6 KiB) TX bytes:15012 (14.6 KiB) nas0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:42 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tunl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 UP RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:41 inet6 addr: fe80::3631:c4ff:fe56:c941/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1973 (1.9 KiB) TX bytes:6375 (6.2 KiB) root@LEDE:/#


Lede 17.01.1 r3316

flashed: lede-17.01.1-lantiq-xway-FRITZ7320-squashfs-sysupgrade.bin

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1820 Version: 2820 (C) Copyright 2005 AVM Date: Jul 16 2013 Time: 15:30:34 (1) 3 0x90000909-0x9000BD1F [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz <create jffs2 from 0x90D80000 len 0x200000 jffs2_size 32> Atheros 8030 detected Eva_AVM >......................................[ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Sat Apr 15 16:13:45 2017 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is FRITZ7320 - 1&1 HomeServer [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00046280 [ 0.000000] Readback ErrCtl register=00046280 [ 0.000000] Memory: 58796K/65536K available (3877K kernel code, 162K rwdata, 620K rodata, 1212K init, 200K bss, 6740K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 393MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9721189849 ns [ 0.000013] sched_clock: 32 bits at 196MHz, resolution 5ns, wraps every 10922685437ns [ 0.007941] Calibrating delay loop... 260.86 BogoMIPS (lpj=521728) [ 0.042400] pid_max: default: 32768 minimum: 301 [ 0.047261] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053804] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.066966] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.076628] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.082836] pinctrl core: initialized pinctrl subsystem [ 0.089638] NET: Registered protocol family 16 [ 0.098889] pinctrl-xway 1e100b10.pinmux: Init done [ 0.104939] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20 [ 0.164505] Can't analyze schedule() prologue at 80009038 [ 0.179101] PCI host bridge /fpi@10000000/pci@E105400 ranges: [ 0.184759] MEM 0x0000000018000000..0x0000000019ffffff [ 0.190013] IO 0x000000001ae00000..0x000000001affffff [ 0.211861] usbcore: registered new interface driver usbfs [ 0.217416] usbcore: registered new interface driver hub [ 0.222753] usbcore: registered new device driver usb [ 0.228143] PCI host bridge to bus 0000:00 [ 0.232152] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.239060] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.246004] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.252860] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.261554] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 0.269388] clocksource: Switched to clocksource MIPS [ 0.275948] NET: Registered protocol family 2 [ 0.281579] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.288482] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.294872] TCP: Hash tables configured (established 1024 bind 1024) [ 0.301505] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.307261] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.313853] NET: Registered protocol family 1 [ 0.326051] gptu: totally 6 16-bit timers/counters [ 0.330930] gptu: misc_register on minor 63 [ 0.335022] gptu: succeeded to request irq 126 [ 0.339505] gptu: succeeded to request irq 127 [ 0.344019] gptu: succeeded to request irq 128 [ 0.348532] gptu: succeeded to request irq 129 [ 0.353046] gptu: succeeded to request irq 130 [ 0.357563] gptu: succeeded to request irq 131 [ 0.363157] Crashlog allocated RAM at address 0x3f00000 [ 0.393368] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.399145] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.414068] io scheduler noop registered [ 0.417899] io scheduler deadline registered (default) [ 0.423861] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.432789] console [ttyLTQ0] enabled [ 0.432789] console [ttyLTQ0] enabled [ 0.440037] bootconsole [early0] disabled [ 0.440037] bootconsole [early0] disabled [ 0.449084] lantiq nor flash device: 01000000 at 10000000 [ 0.453260] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.462544] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.467637] Amd/Fujitsu Extended Query version 1.3. [ 0.472617] number of CFI chips: 1 [ 0.476027] 4 ofpart partitions found on MTD device ltq_nor [ 0.481509] Creating 4 MTD partitions on "ltq_nor": [ 0.486337] 0x000000000000-0x000000020000 : "urlader" [ 0.495637] 0x000000020000-0x000000f80000 : "firmware" [ 0.538866] 2 eva-fw partitions found on MTD device firmware [ 0.543109] 0x000000020000-0x00000019cd49 : "kernel" [ 0.550211] 0x0000001a0100-0x000000f80000 : "rootfs" [ 0.556305] mtd: device 3 (rootfs) set to be root filesystem [ 0.560628] 1 squashfs-split partitions found on MTD device rootfs [ 0.566658] 0x000000440000-0x000000f80000 : "rootfs_data" [ 0.574714] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.581056] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 0.596401] libphy: ltq_mii: probed [ 0.598762] eth0: attached PHY [Generic PHY] (phy_addr=1e180000.etop-ff:00, irq=-1) [ 0.607618] wdt 1f8803f0.watchdog: Init done [ 0.614013] NET: Registered protocol family 10 [ 0.624428] NET: Registered protocol family 17 [ 0.627584] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.639964] 8021q: 802.1Q VLAN Support v1.8 [ 0.644196] found entry name -> annex=B [ 0.647963] found entry name -> maca=34:31:C4:56:C9:3F [ 0.652992] found entry name -> macb=34:31:C4:56:C9:40 [ 0.658084] found entry name -> macwlan=34:31:C4:56:C9:41 [ 0.663430] found entry name -> macdsl=34:31:C4:56:C9:42 [ 0.668794] found entry name -> macwlan2=34:31:C4:56:C9:44 [ 0.674138] found entry name -> wlan_key=52492293968187462901 [ 0.696587] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.704373] Freeing unused kernel memory: 1212K (80491000 - 805c0000) [ 2.480025] init: Console is alive [ 2.482421] init: - watchdog - [ 5.417657] dwc2 1e101000.ifxhcd: DWC OTG Controller [ 5.421223] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1 [ 5.428522] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000 [ 5.435579] hub 1-0:1.0: USB hub found [ 5.438493] hub 1-0:1.0: 1 port detected [ 5.444610] init: - preinit - [ 6.309522] random: procd: uninitialized urandom read (4 bytes read, 26 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.598397] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 9.610430] urandom-seed: Seed file not found (/etc/urandom.seed) [ 9.777354] procd: - early - [ 9.779068] procd: - watchdog - [ 10.475474] procd: - ubus - [ 10.634267] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.643231] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.651458] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.659764] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.669277] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.677534] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.686738] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.695635] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.704865] procd: - init - Please press Enter to activate this console. [ 11.261869] NET: Registered protocol family 8 [ 11.264766] NET: Registered protocol family 20 [ 11.276570] PPP generic driver version 2.4.2 [ 11.287963] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.304710] IFX MEI Version 5.00.00 [ 11.315577] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 [ 11.328814] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 11.335400] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 11.346811] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.358931] ATM1.0.26 ATM (A1) firmware version 0.16 [ 11.362749] ifxmips_atm: ATM init succeed [ 11.477289] Infineon Technologies DEU driver version 2.0.0 [ 11.483609] IFX DEU DES initialized (multiblock). [ 11.488235] IFX DEU AES initialized (multiblock). [ 11.492099] IFX DEU ARC4 initialized (multiblock). [ 11.496626] IFX DEU SHA1 initialized. [ 11.500211] IFX DEU MD5 initialized. [ 11.503754] IFX DEU SHA1_HMAC initialized. [ 11.507806] IFX DEU MD5_HMAC initialized. [ 11.520048] nf_conntrack version 0.5.0 (937 buckets, 3748 max) [ 11.545735] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 11.551182] owl-loader 0000:00:0e.0: Direct firmware load for ath9k-eeprom-pci-0000:00:0e.0.bin failed with error -2 [ 11.560439] owl-loader 0000:00:0e.0: Falling back to user helper [ 11.571013] NET: Registered protocol family 24 [ 11.597010] xt_time: kernel timezone is -0000 [ 11.700170] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available) [ 12.191464] owl-loader 0000:00:0e.0: fixup device configuration [ 12.198687] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 12.204265] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 12.235132] ath: phy0: eeprom contains invalid mac address: 00:00:00:00:00:00 [ 12.240879] ath: phy0: random mac address will be used: be:10:31:cf:73:7a [ 12.273240] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30 [ 25.438070] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 25.457496] jffs2_build_filesystem(): unlocking the mtd device... done. [ 25.462615] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 28.743338] device eth0 entered promiscuous mode [ 28.768640] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 29.929057] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready [ 31.585501] random: nonblocking pool is initialized [ 110.507342] done. [ 110.507863] jffs2: notice: (953) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. BusyBox v1.25.1 () built-in shell (ash) _________ / /\ _ ___ ___ ___ / LE / \ | | | __| \| __| / DE / \ | |__| _|| |) | _| /________/ LE \ |____|___|___/|___| lede-project.org \ \ DE / \ LE \ / ----------------------------------------------------------- \ DE \ / Reboot (17.01.1, r3316-7eb58cf109) \________\/ ----------------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@LEDE:/#


(OEM) EVA Revision: 1.1820 Version: 2820

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1820 Version: 2820 (C) Copyright 2005 AVM Date: Jul 16 2013 Time: 15:30:34 (0) 3 0x90000909-0x9000BD1F [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz Atheros 8030 detected Eva_AVM >.......................... Lantiq xDSL CPE AR9 [ifx_enhance_phy_clock] PLL0_CFG: 0x00b05f23 [ifx_enhance_phy_clock] Setting new PLL0_CFG for external PHY... [ifx_enhance_phy_clock] finished. [ 0.000000] Linux version 2.6.32.61 (jpluschke@EmbeddedVM) (gcc version 4.8.1 (Buildroot 2013.05) ) #1 Tue May 2 10:31:26 CEST 2017 [ 0.000000] phym = 04000000, mem = 04000000, max_pfn = 00004000 [ 0.000000] Reserving memory for CP1 @0xa4000000, size 0x00000000 [ 0.000000] wlan_mem_start = 0x03f9e000 [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 804aa000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001954c (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00003f9e [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00003f9e [ 0.000000] [c55] c55_mem_start = 0xfc0000 [ 0.000000] [module-alloc-by-name] 'modulemem' not in use, use AVM Kernel Config (6758400 bytes, reserved for module mem) [ 0.000000] [module-alloc] use 0x672000 bytes at 0x81081000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16158 [ 0.000000] Kernel command line: console=ttyS1,115200n8r nor_size=16MB ethaddr=34:31:C4:56:C9:3F [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=189 to write through [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0004628d [ 0.000000] Readback ErrCtl register=0004628d [ 0.000000] Memory: 52316k/65144k available (3383k kernel code, 12752k reserved, 1388k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] [mips_cpu_irq_init] irq_base 0 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 261.32 BogoMIPS (lpj=1306624) [ 0.230000] Security Framework initialized [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] kernel_init: started [ 0.240000] kernel_init: kernel locked [power_managment_setup] reset 'DSL, DFE, AFE, VOICE, DSLTC, ARC' [power_managment_setup] reset 'LDO' [power_managment_setup] power down 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0' [power_managment_setup] power down 'MSI1, PDI1 PCIE1 PCIE1_PHY' [power_managment_setup] power down 'USB CTRL' [power_managment_setup] power down 'GPHY' [power_managment_setup] disable power domain 'DSL + DFE' [ 0.280000] NET: Registered protocol family 16 [ 0.290000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.290000] Reboot Status is: Short-PowerOff-Reboot [ 0.300000] [avmnet] [avmnet_cfg_init] Driver version: 6.137.1.1 - Revision 1496:3362 - Mi 8. Mär 12:37:40 CET 2017 [ 0.310000] Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.320000] bio: create slab <bio-0> at 0 [ 0.320000] pci 0000:00:00.0: PME# supported from D1 D2 [ 0.330000] pci 0000:00:00.0: PME# disabled [ 0.330000] NET: Registered protocol family 8 [ 0.330000] NET: Registered protocol family 20 [ 0.340000] NET: Registered protocol family 2 [ 0.340000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.350000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.360000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.370000] TCP reno registered [ 0.370000] NET: Registered protocol family 1 [ 0.370000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 ,(c)2009 Infineon Technologies AG [ 0.370000] skb_shared_size:344 [ 0.390000] [bcu_control_interrupt] 'FPI Slave BCU0' Error Interrupt [ 0.390000] Slave BCU[sBCU_EADD]: Error Address Register: 0x17000004 [ 0.390000] Slave BCU[sBCU_EDAT]: Error Data Capture Register: 0x0290030f [ 0.390000] Slave BCU[sBCU_CON] : Control Register: 0x4009ffff [ 0.390000] Slave BCU[sBCU_ECON]: Error Register (0x21be0030): [ 0.390000] FPI Bus Operation Code 0x2 [ 0.390000] FPI Bus Tag Number 0x1 [ 0.390000] FPI Bus Read Signal: passive [ 0.390000] FPI Bus Write Signal: active [ 0.390000] FPI Bus Supervisor Mode: active [ 0.390000] FPI Bus Acknowladge Signal: 0x3 [ 0.390000] FPI Bus Abort: passive [ 0.390000] FPI Bus Ready: active [ 0.390000] FPI Bus Timeout: not pressed [ 0.390000] FPI Bus Error Counter: 48 [ 0.460000] [bcu_control_init] interrupts for BCU installed [ 0.460000] Lantiq CGU driver, version 1.1.32, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.470000] clk-timing: timing:16, ram_refresh_timing:1524, base_ram_refresh_timing:7775 [ 0.480000] smvp_tc_init: tc 0 tcbind 00020000 tcstatus 18102000 [ 0.480000] smvp_tc_init: tc 1 tcbind 00200001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 2 tcbind 00400001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 3 tcbind 00600001 tcstatus 00000400 [ 0.480000] config3 0x424 MT 1 [ 0.480000] MVPControl 0x2, STLB 0 VPC 1 EVP 0 [ 0.480000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1 [ 0.510000] initcall 0x804b19cc returned with disabled interrupts [ 0.520000] audit: initializing netlink socket (disabled) [ 0.520000] type=2000 audit(0.523:1): initialized [ 0.530000] squashfs: version 3.4 (2008/08/26) Phillip Lougher [ 0.540000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540000] fuse init (API version 7.13) [ 0.550000] msgmni has been set to 102 [ 0.550000] io scheduler noop registered (default) [ 0.550000] system-load 1 loadavg 0.0 0.0 0.0 - 11 tasks:0 % curr:swapper(0 %) max:swapper(0 %, pid:1), readytorun: 1, pgfault 0/s (max 0 avg 0.0) [ 0.570000] [avm_membench_init] [ 0.860000] avm_net_trace: Up and running. [ 0.870000] [loadcontrol] set auto - scale=1 [ 0.870000] [avm] configured: watchdog event debug [ 0.880000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: May 2 2017 10:30:27) [ 0.890000] ifx_pmu_init: Major 245 [ 0.890000] Lantiq PMU driver, version 1.2.6, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.900000] Infineon Technologies RCU driver version 1.0.7 [ 0.900000] ttyS0 at MMIO 0x1e100400 (irq = 100) is a PORT_IFX_ASC [ 0.910000] ttyS1 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 0.920000] loop: module loaded [ 0.920000] nbd: registered device at major 43 [ 0.940000] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 0.950000] Platform NOR MTD, (c) AVM 2010 [ 0.950000] [plat_nor_probe]start probe [ 0.950000] [do_map_probe] driver_name=cfi_probe [ 0.960000] mtd-nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 0.970000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.970000] mtd-nor: CFI does not contain boot bank location. Assuming top. [ 0.980000] number of CFI chips: 1 [ 0.980000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 0.990000] [ifx_jffs2_parser_function] magic 19852003 found @pos 0xd80000, size 2097152 [ 1.010000] [ifx_squashfs_parser_function] magic found @pos 0x179300 [ 1.010000] 6 find_squashfs partitions found on MTD device mtd-nor [ 1.020000] Creating 6 MTD partitions on "mtd-nor": [ 1.020000] 0x000000179300-0x000000f80000 : "rootfs" [ 1.030000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.040000] 0x000000020000-0x000000179300 : "kernel" [ 1.050000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.060000] 0x000000000000-0x000000020000 : "urlader" [ 1.070000] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 1.070000] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 1.080000] 0x000000d80000-0x000000f80000 : "jffs2" [ 1.080000] mtd-nor mtd-nor: registered mtd device [ 1.090000] tun: Universal TUN/TAP device driver, 1.6 [ 1.090000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.100000] IFX SWITCH API, Version 1.1.8.5 [ 1.100000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.210000] CAPI Subsystem Rev 1.1.2.8 [ 1.210000] AVM PA 4.3.12 2015-11-11 [ 1.220000] AVM PA skb pktinfo at offset 128 size 196 [ 1.220000] [loadcontrol]module avm_pa registered [ 1.230000] IPv4 over IPv4 tunneling driver [ 1.230000] TCP cubic registered [ 1.230000] mcfw: IGMPv3 fast forwarding [ 1.240000] NET: Registered protocol family 10 [ 1.240000] NET: Registered protocol family 17 [ 1.250000] NET: Registered protocol family 8 [ 1.250000] atmpvc_init() failed with -17 [ 1.250000] KOAM is loaded successfully. [ 1.260000] l2tp_core: L2TP core driver, V2.0 [ 1.260000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.270000] l2tp_netlink: L2TP netlink interface [ 1.270000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.280000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.290000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0) [ 1.290000] mount on mtd3 and mtd4 (double buffering) [ 1.300000] TFFS Name Table L [ 1.300000] Adam2 environment variables API installed. [ 1.310000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 1.310000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.330000] Setup tcs=0x1 current_tc_mask=0x1, reg=0 [ 1.330000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 1.340000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.350000] Setup tcs=0x1 current_tc_mask=0x1, reg=1 [ 1.360000] AVM Simple Profiling enabled Version 3.0 [ 1.360000] {avmnet_cfg_netinit} [ 1.370000] [avmnet] No config found for HWRev 189, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev [ 1.380000] [avmnet] No config found for HWRev 189, HWSubRev 1, trying base config for HWRev [ 1.380000] {avmnet_mac_ar9_init} Init on module mac_ar9_0 called. [ 1.400000] [avmnet] [avmnet_mac_ar9_setup] IFX_AR9_ETH_CTL(0): 0x424001 [ 1.410000] [avmnet] [avmnet_mac_ar9_setup] mac_nr: 0, vlan_reg: 0x4070001 [ 1.540000] [avm_pa_multiplexer_init] start [ 1.540000] [avm_pa_multiplexer_init] init complete [ 1.540000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 34:31:c4:56:c9:3f [ 1.550000] kernel_init: basic setup done [ 1.560000] [squashfs] use lzma compression [ 1.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:0. [ 1.570000] Freeing unused kernel memory: 176k freed [ 1.620000] trying /sbin/init starting pid 104, tty '/dev/ttyS1': '/etc/init.d/rc.S' tar: removing leading '/' from member names source files in group 0 ... /etc/init.d/S00-signal /etc/init.d/S05-watchdog /etc/init.d/S09-rtc /etc/init.d/S01-head /etc/init.d/S08-tffs /etc/init.d/S02-led /etc/init.d/S09-config [ 4.040000] [module-alloc-by-name] give 0x12000 bytes at 0x81081000 to module 'led_modul_Fritz_Box_HW189' (0x660000 bytes left) [ 4.050000] led_modul_Fritz_Box_HW189: module license ' [ 4.050000] (C) Copyright 2012 by AVM [ 4.050000] ' taints kernel. [ 4.070000] Disabling lock debugging due to kernel taint [ 4.090000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 4.110000] AVM_WATCHDOG: System Init UEberwachung 240 Sekunden mknod: /var/flash/ar7.cfg: File exists P-Defaults: do nothing [ 4.790000] [module-alloc-by-name] give 0x1000 bytes at 0x81093000 to module 'rtc_avm' (0x65f000 bytes left) [ 4.820000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 4.820000] [avm-rtc]: avm_rtc_probe: register: ret=0x83126c00 [ 4.830000] [avm-rtc]: avm_rtc_probe: success exceute files in group 0 ... /etc/init.d/E05-basemodules group 0 done ... source files in group 1 ... /etc/init.d/S10-html /etc/init.d/S12-default /etc/init.d/S10-vm /etc/init.d/S15-filesys /etc/init.d/S11-config_def /etc/init.d/S17-capi /etc/init.d/S11-piglet /etc/init.d/S17-tam [ 5.060000] [ 5.060000] [avm_debug] redirecting kernel-messages (/dev/debug) [ 5.110000] [module-alloc-by-name] give 0x8000 bytes at 0x81094000 to module 'Piglet_noemif' (0x657000 bytes left) [ 5.110000] [module-alloc-by-name] 0x8000 bytes used, 0xB510 bytes expected [ 5.130000] [piglet]use default-settings (1 gpio from hw_config) [ 5.240000] [piglet]patch_dectfw: C030C000, totallen = 44825(AF19) [ 5.240000] [piglet]patch_dectfw: patch_adress: A0 max_len: 26 with Version 2 Len: 17 [ 5.240000] [piglet]patch_dectfw: RFPI tag found 0271929880 [ 5.240000] [piglet]patch_dectfw: dectmode 1 [ 5.240000] [piglet]dect_loader144xx: slow-bootmode <FE>* *************************************************************************************** [ 8.530000] [piglet]dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull [ 10.540000] [piglet]TDM: FS: 8005 Hz CLK: 1023995 Hz [ 10.750000] system-load 100 % loadavg 0.15 0.3 0.1 - 22 tasks:24 % curr:mount(0 %) max:init(14 %, pid:1), readytorun: 1, pgfault 2299/s (max 1 avg 1.0) [jffs2] Mount /data success (mtd5 size 2097152) [jffs2] write env variable jffs2_size to 32 [ 10.980000] [module-alloc-by-name] give 0x5F000 bytes at 0x8109C000 to module 'pcmlink' (0x5F8000 bytes left) [ 10.980000] [module-alloc-by-name] 0x5F000 bytes used, 0x685E4 bytes expected [ 11.110000] [pcmlink]VPE-Interface: base 0xFC0000, maxsize 131072, host-irq 142 [ 11.490000] [module-alloc-by-name] give 0xA2000 bytes at 0x810FB000 to module 'isdn_fbox_fon5' (0x556000 bytes left) [ 11.490000] [module-alloc-by-name] 0xA2000 bytes used, 0xB60DC bytes expected [ 11.600000] [pcmlink]chrony-support [ 11.600000] VPE loader: loading segment 1 to 80FC0000 (14000 bytes) elf loaded [ 11.600000] vpe_run: tc 1 start-addr 80FC0000 [ 11.600000] vpe_run: tc 1 tcstatus 18000400 tcbind 00200001 MVPCONTROL 00000002 vpeopt 00000000 [ 12.620000] [isdn]PCMLINK: Version 7.511 (isdn: 3163) Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222) no HwCross DSP-EC: 2 [ 13.050000] [module-alloc-by-name] give 0x54000 bytes at 0x8119D000 to module 'capi_codec' (0x502000 bytes left) [ 13.050000] [module-alloc-by-name] 0x54000 bytes used, 0x5D6B0 bytes expected capicodec_init() [capi_codec] support fax [capi_codec] support Codecs [ 13.080000] : Codecs_Init register a /dev/debug handler [ 13.260000] [module-alloc-by-name] give 0x3A000 bytes at 0x811F1000 to module 'avm_dect' (0x4C8000 bytes left) [ 13.260000] [module-alloc-by-name] 0x3A000 bytes used, 0x42320 bytes expected [ 13.300000] [module-alloc-by-name] give 0x3000 bytes at 0x8122B000 to module 'dect_io' (0x4C5000 bytes left) [ 13.300000] [module-alloc-by-name] 0x3000 bytes used, 0x447C bytes expected TAM: create JFFS2 directory /data/tam exceute files in group 1 ... /etc/init.d/E15-device mknod led c 242 mknod tffs c 243 mknod avm_power c 252 mknod debug c 248 mknod avm_event c 249 mknod capi_oslib c 68 mknod dect_io c 239 / group 1 done ... source files in group 2 ... /etc/init.d/S21-udev exceute files in group 2 ... group 2 done ... source files in group 3 ... /etc/init.d/S30-ledcfg exceute files in group 3 ... group 3 done ... source files in group 4 ... /etc/init.d/S40-swap /etc/init.d/S44-hostname /etc/init.d/S48-configd /etc/init.d/S42-ptest /etc/init.d/S46-usb Jan 1 01:00:13 udevd[364]: specified group 'tty' unknown Jan 1 01:00:13 udevd[364]: specified group 'dialout' unknown Jan 1 01:00:13 udevd[364]: specified group 'kmem' unknown Jan 1 01:00:13 udevd[364]: specified group 'video' unknown Jan 1 01:00:13 udevd[364]: specified group 'audio' unknown Jan 1 01:00:13 udevd[364]: specified group 'lp' unknown Jan 1 01:00:13 udevd[364]: specified group 'disk' unknown Jan 1 01:00:13 udevd[364]: specified group 'floppy' unknown Jan 1 01:00:13 udevd[364]: specified group 'cdrom' unknown [ 13.860000] [module-alloc-by-name] give 0x1000 bytes at 0x8122E000 to module 'lzo_compress' (0x4C4000 bytes left) [ 13.860000] [module-alloc-by-name] 0x1000 bytes used, 0x1878 bytes expected [ 13.860000] [module-alloc-by-name] give 0x1000 bytes at 0x8122F000 to module 'lzo_decompress' (0x4C3000 bytes left) [ 13.860000] [module-alloc-by-name] 0x1000 bytes used, 0x1938 bytes expected Jan 1 01:00:13 udevd[364]: specified group 'tape' unknown <6>udev: starting version 151 [ 13.930000] [module-alloc-by-name] give 0x4000 bytes at 0x81230000 to module 'ramzswap' (0x4BF000 bytes left) [ 13.930000] [module-alloc-by-name] 0x4000 bytes used, 0x58E0 bytes expected [ 13.960000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192mknod: /dev/ramzswap0: File exists [ 14.000000] Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS exceute files in group 4 ... /etc/init.d/E40-dsl /etc/init.d/E46-net /etc/init.d/E47-voip [dsl sus] dsl line test calib factory file available [dsl get xtse] ANNEX=B [dsl get xtse] setting Annex B and J [dsl get xtse] 10 00 10 40 00 04 01 00 [dsl sus] starting ar9 dsp... [dsl sus] ANNEX=B DIAGNOSE=no [ 14.920000] [module-alloc-by-name] give 0x9000 bytes at 0x81234000 to module 'ifxmips_mei' (0x4B6000 bytes left) [ 14.920000] [module-alloc-by-name] 0x9000 bytes used, 0xBC1C bytes expected [dsl mei] Lantiq MEI driver version: 5.03.00 [dsl mei] Lantiq MEI driver global debug_level: 0 [dsl sus] loaded ar9 mei driver: ifxmips_mei.ko with params: [ 15.160000] [module-alloc-by-name] give 0x4D000 bytes at 0x8123D000 to module 'drv_dsl_cpe_api' (0x469000 bytes left) [ 15.160000] [module-alloc-by-name] 0x4D000 bytes used, 0x568A8 bytes expected [dsl drv] Lantiq CPE API Driver version: DSL CPE API V4.9.2.1 [dsl drv] Predefined debug level: 4 [dsl drv] dynamically registered major number 238 for drv_dsl_cpe_api [dsl sus] loaded ar9 dsl driver: drv_dsl_cpe_api.ko with params: [dsl sus] created ar9 dsl device node /dev/dsl_ar9 (major: 238 , minor: 0) [dsl sus] created ar9 mei device node /dev/ifx_mei (major: 105 , minor: 0) [dsl sus] started dsl_control (configuration: -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.sh ) nohup: appending output to nohup.out 0 [dsl sus] started dsl_monitor [dsl sus] ....ar9 dsp started [ 17.090000] [module-alloc-by-name] give 0x138000 bytes at 0x8128A000 to module 'kdsldmod' (0x331000 bytes left) [ 17.090000] [module-alloc-by-name] 0x138000 bytes used, 0x16CDE0 bytes expected [ 17.250000] kdsldmod: init start (Mar 8 2017 12:59:33) sizeof(struct sk_buff)=440 [ 17.260000] userman: device registerd (userman_url) with major=232 <6>kdsld: ttychannel: ldisc 8 registered [ 17.260000] PCP_NL: PCP netlink interface (multicast group 1) [ 17.260000] kdsldmod: init done (Mar 8 2017 12:59:33) /etc/init.d/E46-net: /etc/init.d/rc.net: line 527: l2tpv3d: not found Jan 1 01:00:18 ctlmgr[579]: pcpc_create_ctx: no pcpserver found Jan 1 01:00:19 upnpd[585]: starting ... 1970-01-01 01:00:19 upnpd[585]: ready (0sec) [ 20.950000] system-load 100 % loadavg 0.36 0.8 0.3 - 49 tasks:32 % curr:mtdblockd(8 %) max:ctlmgr(12 %, pid:581), readytorun: 2, pgfault 4266/s (max 2 avg 1.0) Jan 1 01:00:21 multid[595]: startup ($Revision: 29113 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:21 multid[595]: starting ... Jan 1 01:00:21 multid[597]: HWRevision=189 Jan 1 01:00:21 multid[597]: l2tpcfg_cfg2buf: size 161 Jan 1 01:00:21 multid[597]: opt_without_tr069discover=0, AR7CFG->vinax_hsi_lan_ports=, multid.use_vinax=0, multid.tcom_targetarch=0, is_eth_switch_installed()=0, multid.cpmac_no_ata_possible=0, pppoeiface=nuller Jan 1 01:00:21 multid[597]: setup_cpmac: get_pppoeiface=???, multid.wan_iface_name=eth0 Jan 1 01:00:21 multid[597]: bridge_configured: is_vinax=0, is_ata=0, bridge_with_switch_separation=1 Jan 1 01:00:21 multid[597]: bridge_configured: nqos_bridge_active=0, bridge_port_set=0x0, igmp_flt_portset=0x0 Jan 1 01:00:21 multid[597]: bridge_configured: portnumber=1, portbit=0x1, mode=0 Jan 1 01:00:21 multid[597]: bridge_configured: other_bridge_active=0, effective bridge_port_set=0x0 Jan 1 01:00:21 multid[597]: ipv6_remove_addresses_for(eth0) Jan 1 01:00:21 multid[597]: create new bridge lan [avm_power] eth: port 0 force normal CON t0 [ 22.220000] ADDRCONF(NETDEV_UP): lan: link is not ready [ 22.220000] ADDRCONF(NETDEV_UP): lan: link is not ready Jan 1 01:00:22 ctlmgr[581]: WLANLIB: wlan_plugin_init:630: svn revision 2555 [ 22.570000] DSP: XDU=1( D1 ) OVR=0 MIPS_OVR=0 [ 22.860000] ADDRCONF(NETDEV_UP): eth0: link is not ready Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:73: Missing weak 'wlan_get_known_wlan_macs'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:76: Missing weak 'process_wlanmail'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:79: Missing weak 'wlan_enabled_changed'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:82: Missing weak 'wlan_wcfgutil_set_output'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:83: Missing weak 'wlan_wcfgutil_set_dbg_level'. Jan 1 01:00:22 multid[597]: remove_iface_from_other_linuxbridges: iface=eth0, br_exclude=lan Jan 1 01:00:22 multid[597]: br_get_list1: (AVM) num=1 Jan 1 01:00:22 multid[597]: list[0]=lan Jan 1 01:00:22 multid[597]: add eth0 to linuxbridge(2) lan [ 22.970000] device eth0 entered promiscuous mode Jan 1 01:00:22 multid[597]: create new bridge guest [ 24.000000] ADDRCONF(NETDEV_UP): guest: link is not ready [ 24.000000] ADDRCONF(NETDEV_UP): guest: link is not ready Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(lan) Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(guest) Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: sum portmap=0x0 Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: reset igmp netfilter Jan 1 01:00:24 multid[597]: snooping for lan? 1 Jan 1 01:00:24 multid[597]: multicast_snooping for bridge lan = 1 Jan 1 01:00:24 multid[597]: snooping for lan:0? 1 Jan 1 01:00:24 multid[597]: snooping for guest? 1 Jan 1 01:00:24 multid[597]: multicast_snooping for bridge guest = 1 Jan 1 01:00:24 multid[597]: mrouter: using IGMPv3 for upstream interface dsl Jan 1 01:00:24 multid[597]: mrouter: using IGMPv3 for other interfaces Jan 1 01:00:24 multid[597]: resolv.conf with 127.0.0.1 written Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 4 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 5 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 6 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: DHCPD: TR111 enabled Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: DHCPD on lan:0 skipped, is virtual interface Jan 1 01:00:24 multid[597]: DHCPD on guest Jan 1 01:00:24 multid[597]: open(/dev/userman) - No such file or directory (2) Jan 1 01:00:24 multid[597]: open(/dev/userman) - No such file or directory (2) Jan 1 01:00:24 multid[597]: neighbour: real mac for Amigo changed from 18:cf:5e:0b:72:e3 to 00:50:b6:1a:3c:84 Jan 1 01:00:24 multid[597]: neighbour: real mac for BNELKA-DE changed from a4:4e:31:3e:33:20 to e4:b3:18:9c:65:d5 Jan 1 01:00:24 multid[597]: neighbour: real mac for Tommys-iPhone changed from b8:e8:56:f1:d3:52 to b4:8b:19:70:a7:c0 Jan 1 01:00:24 multid[597]: neighbour: real mac for iPhone-BUN changed from dc:41:5f:b4:44:f4 to b0:48:1a:93:27:4e [ 24.280000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 24.280000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 24.280000] lan: port 1(eth0) entered forwarding state [ 24.280000] lan: port 1(eth0) entered forwarding state [ 24.280000] ADDRCONF(NETDEV_CHANGE): lan: link becomes ready Jan 1 01:00:24 multid[597]: neighbour: real mac for iPhonevtzGrosch changed from 4c:8d:79:66:9d:0e to 60:d9:c7:09:52:dc [ 24.300000] [dma_device_write] auto open tx_chan_no:0 [ 24.300000] Added 83AA7090M recipient for mc group 825D5530I6 (vid: 0), now 1 recipientsJan 1 01:00:24 multid[597]: add_jasonii_dns_rebind_protection_exceptions: free list Jan 1 01:00:24 multid[597]: Warning: dnsd_start: no dns server added Jan 1 01:00:24 multid[597]: interface lo new. Jan 1 01:00:24 multid[597]: mrouter: lan: vif 0 if_index 5 Jan 1 01:00:24 multid[597]: interface lo up. Jan 1 01:00:24 multid[597]: interface lo carrier up Jan 1 01:00:24 multid[597]: interface tunl0 new. Jan 1 01:00:24 multid[597]: interface eth0 new. Jan 1 01:00:24 multid[597]: remove_iface_from_other_linuxbridges: iface=eth0, br_exclude=lan Jan 1 01:00:24 multid[597]: br_get_list1: num=2 Jan 1 01:00:24 multid[597]: list[0]=lan Jan 1 01:00:24 multid[597]: list[1]=guest Jan 1 01:00:24 multid[597]: br_get_interfaces(guest)=0 Jan 1 01:00:24 multid[597]: add eth0 to linuxbridge(2) lan Jan 1 01:00:24 multid[597]: setup_mc_mdb: bridgename=lan etherdevname=eth0 (239.255.255.250) Jan 1 01:00:24 multid[597]: interface eth0 up. Jan 1 01:00:24 multid[597]: interface eth0 carrier up Jan 1 01:00:24 multid[597]: setup_mc_mdb: bridgename=lan etherdevname=eth0 (239.255.255.250) Jan 1 01:00:24 multid[597]: interface adsl new. Jan 1 01:00:24 multid[597]: interface lan new. Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: interface lan up. Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: interface lan carrier up Jan 1 01:00:24 multid[597]: interface guest new. Jan 1 01:00:24 multid[597]: interface guest up. Jan 1 01:00:24 multid[597]: DHCPD on guest Jan 1 01:00:24 multid[597]: mrouter: lan: vif 0 if_index 5 Jan 1 01:00:24 multid[597]: mrouter: guest: vif 1 if_index 6 Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(lan) Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(guest) 1970-01-01 01:00:24 multid[595]: ready (3sec) Jan 1 01:00:24 multid[597]: verbose: DISABLED Jan 1 01:00:24 ddnsd[651]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:24 ddnsd[651]: starting ... Jan 1 01:00:24 ddnsd[653]: DDNS: no valid accounts 1970-01-01 01:00:24 ddnsd[651]: [651]: Daemon start failed (0sec) Jan 1 01:00:24 ddnsd[653]: [653] Start failed FATAL: ddnsd not running after started Jan 1 01:00:25 pcpd[655]: startup (Mar 8 2017 12:55:52) Jan 1 01:00:25 pcpd[655]: starting ... Jan 1 01:00:25 pcpd[657]: Local v4 address: 192.168.178.1 Jan 1 01:00:25 pcpd[657]: verbose: DISABLED 1970-01-01 01:00:25 pcpd[655]: ready (0sec) Jan 1 01:00:25 upnpdevd[659]: startup ($Revision: 1.11 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:25 upnpdevd[659]: starting ... Jan 1 01:00:25 upnpdevd[661]: CONFIG_LOGD disabled: No UPnP-Device for avmlogd 1970-01-01 01:00:25 upnpdevd[659]: ready (0sec) Jan 1 01:00:25 upnpdevd[661]: verbose: DISABLED rc.wlan: Start WLAN... [ 25.630000] Added 83B2F090M recipient for mc group 82447E30I6 (vid: 0), now 1 recipientsWLAND:[00670]:01:00.25/[25.79]:BUILD: Mar 8 2017, 13:08:39 [ 26.900000] [module-alloc-by-name] give 0x20000 bytes at 0x813C2000 to module 'aae' (0x311000 bytes left) [ 26.900000] [module-alloc-by-name] 0x20000 bytes used, 0x262B0 bytes expected [ 27.050000] [wlan_config] Given config is: [ 27.050000] [wlan_config] hw_interface=0 chip_type=3 (kiwi) offload=1 (non) [ 27.050000] [wlan_config] hwrev=189 hwsubrev=1 maca=34:31:C4:56:C9:3F [ 27.050000] [wlan_eeprom] Calibration data blocks found = 1 [ 27.050000] [wlan_eeprom] EEPROM #1, type "AR92x7": [ 27.050000] [wlan_eeprom] regDmn=0x8114 - patching to 0 [ 27.050000] [wlan_eeprom] Build with ART 0.9b21 [ 27.050000] avm_net_trace: New net trace device 'WLAN Management Traffic' registered with minor 128. Jan 1 01:00:27 dsld[673]: startup ($Revision: 28389 $$CompileDate: Mar 8 2017 12:56:19 $) Jan 1 01:00:27 dsld[673]: set_preconfig1 Jan 1 01:00:27 dsld[673]: sync_group in ar7.cfg: Jan 1 01:00:27 dsld[673]: sync_group:sync_dsl(enabled=1), nr=0 Jan 1 01:00:27 dsld[673]: vcc:1/32 Jan 1 01:00:27 dsld[673]: dsliface:internet Jan 1 01:00:27 dsld[673]: dsliface:mstv Jan 1 01:00:27 dsld[673]: vcc:1/35 Jan 1 01:00:27 dsld[673]: dsliface:voip Jan 1 01:00:27 dsld[673]: sync_group: dsl Jan 1 01:00:27 dsld[673]: sync_dsl is igd_device Jan 1 01:00:27 dsld[673]: set_preconfig2 Jan 1 01:00:27 dsld[673]: add_vcc_connection: 1/32, sync_group=dsl Jan 1 01:00:27 dsld[673]: add_vcc_connection: 1/35, sync_group=dsl Jan 1 01:00:27 dsld[673]: starting ... Jan 1 01:00:27 dsld[693]: DSL Mac 34:31:c4:56:c9:42 Jan 1 01:00:27 dsld[693]: VOIP Mac 34:31:c4:56:c9:43 Jan 1 01:00:27 dsld[693]: VCC2 Mac 34:31:c4:56:c9:44 Jan 1 01:00:27 dsld[693]: VCC3 Mac 34:31:c4:56:c9:40 <3>kdsld: kdsld_vcc_preunregister: * [ 27.210000] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0 Jan 1 01:00:27 dsld[693]: sync_group(prepare_interfaces): dsl: inet_nr=0 Jan 1 01:00:27 dsld[693]: nach prepare_interfaces: dsld.dsliface_default_inet_nr=0, dsld.dsliface_voip_nr=1 Jan 1 01:00:27 dsld[693]: get_queueindex: none: not found Jan 1 01:00:27 dsld[693]: get_queueindex: none: not found Jan 1 01:00:27 dsld[693]: queue 0: prio 0 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 1: prio 10 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 2: prio 20 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 3: prio 30 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 4: prio 100 weight 90 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 5: prio 100 weight 10 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 6: prio 200 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: appl 0: sip-appl result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sip" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark rtp" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sipdns,ntpdns,tr069dns,tr069" result 2 Jan 1 01:00:27 dsld[693]: classifer: local "localmark webdav" result 3 Jan 1 01:00:27 dsld[693]: classifer: lan "ip.proto IPv6-ICMP" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "ip.proto icmp" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 53" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 5060" result 4 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sip_internet" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark rtp_internet" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark dns" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "tcp.dport 5060" result 4 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 43962 ip.tos 0x60" result 5 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 47806 ip.tos 0x60" result 5 Jan 1 01:00:27 dsld[693]: classifer: local "localmark igmp ip.tos 0x60" result 6 Jan 1 01:00:27 dsld[693]: classifer: local "localmark igmp" result 7 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 123 ip.tos 0x60" result 8 Jan 1 01:00:27 dsld[693]: classifer: lan "tcp.dport 80 ip.tos 0x60" result 8 Jan 1 01:00:27 dsld[693]: result 0: tos 65535 vprio 65535 queue 5 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 1: tos 65535 vprio 65535 queue 2 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 2: tos 65535 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 3: tos 65535 vprio 65535 queue 6 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 4: tos 65535 vprio 65535 queue 2 appl 0 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 5: tos 96 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 6: tos 128 vprio 4 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 7: tos 0 vprio 0 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 8: tos 128 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: interface lo added. Jan 1 01:00:27 dsld[693]: interface lo up. Jan 1 01:00:27 dsld[693]: interface lo carrier_up. Jan 1 01:00:27 dsld[693]: interface tunl0 added. Jan 1 01:00:27 dsld[693]: interface eth0 added. Jan 1 01:00:27 dsld[693]: interface eth0 up. Jan 1 01:00:27 dsld[693]: interface eth0 carrier_up. Jan 1 01:00:27 dsld[693]: interface adsl added. Jan 1 01:00:27 dsld[693]: interface lan added. Jan 1 01:00:27 dsld[693]: interface lan up. Jan 1 01:00:27 dsld[693]: interface lan carrier_up. Jan 1 01:00:27 dsld[693]: interface guest added. Jan 1 01:00:27 dsld[693]: interface guest up. Jan 1 01:00:27 dsld[693]: start register_vccs_and_ifaces_on_kdsld for sync_dsl Jan 1 01:00:27 dsld[693]: setup_dslchannel: ifname= Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: predsl1 <3>kdsld: kdsld_vcc_preregister: predsl1 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: kdsld_vccidx=0 [ 27.510000] kdsld: voip: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=1 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44ec00) Jan 1 01:00:27 dsld[693]: setup_dslchannel: ifname= Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: predsl2 <3>kdsld: kdsld_vcc_preregister: predsl2 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: kdsld_vccidx=1 [ 27.540000] kdsld: internet: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=0 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44eb8c) [ 27.540000] kdsld: IPv6: mstv: link local fe80::3631:c4ff:fe56:c944 remote :: [ 27.540000] kdsld: mstv: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=2 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44ec74) Jan 1 01:00:27 dsld[693]: udslinterface_set_internet_forwardrules: FORWARDRULES_INTERNET_NORMAL=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 [ 27.610000] kdsld: route-dsl: set_snd_ipaddr: 192.168.180.1 [ 27.610000] kdsld: route-dsl: set_rcv_ipaddr: 192.168.180.1 Jan 1 01:00:27 dsld[693]: voip_backup: enabled 1970-01-01 01:00:27 dsld[673]: ready (0sec) Jan 1 01:00:27 dsld[693]: verbose: DISABLED Notify type: DSL_INTERFACE_STATUS Jan 1 01:00:30 telefon[800]: use clock_gettime(CLOCK_MONOTONIC)! Jan 1 01:00:30 telefon[800]: No S0NT! Jan 1 01:00:30 telefon[800]: NoOldMSNNames telefon: SIGCHLD PID 840 received! Jan 1 01:00:30 telefon[800]: WARNING No config file '/var/flash/fx_def' ! [ 31.080000] system-load 100 % loadavg 0.84 0.19 0.6 - 61 tasks:49 % curr:telefon(5 %) max:ctlmgr(27 %, pid:581), readytorun: 2, pgfault 4668/s (max 3 avg 1.0) Jan 1 01:00:31 telefon[800]: INFO No MOH file '/var/flash/fx_moh' ! [ 31.760000] [module-alloc-by-name] give 0x21000 bytes at 0x813E2000 to module 'krtp' (0x2F0000 bytes left) [ 31.760000] [module-alloc-by-name] 0x21000 bytes used, 0x2670C bytes expected [ 32.290000] [module-alloc-by-name] give 0x1000 bytes at 0x81403000 to module 'sch_tbf' (0x2EF000 bytes left) [ 32.290000] [module-alloc-by-name] 0x1000 bytes used, 0x263C bytes expected [ 32.410000] [module-alloc-by-name] give 0x2000 bytes at 0x81404000 to module 'sch_llq' (0x2ED000 bytes left) [ 32.410000] [module-alloc-by-name] 0x2000 bytes used, 0x3714 bytes expected [ 32.420000] sch_llq: May 2 2017 10:30:56 [ 32.500000] [module-alloc-by-name] give 0x2000 bytes at 0x81406000 to module 'sch_sfq' (0x2EB000 bytes left) [ 32.500000] [module-alloc-by-name] 0x2000 bytes used, 0x28BC bytes expected telefon: SIGCHLD PID 926 received! Jan 1 01:00:32 telefon[899]: NoOldMSNNames Jan 1 01:00:33 dsld[693]: !!!!!!!!!!!!!!!!!route_add: default: metric=2, iface=dsl mknod: /var/flash/fx_def: File exists telefon: SIGCHLD PID 939 received! Jan 1 01:00:33 telefon[899]: WARNING No config file '/var/flash/fx_def' ! Jan 1 01:00:33 voipd[918]: starting ... Jan 1 01:00:34 dsld[693]: udslinterface_set_forwardrules: group=0 1970-01-01 01:00:34 voipd[918]: ready (1sec) group 4 done ... source files in group 5 ... exceute files in group 5 ... group 5 done ... source files in group 6 ... exceute files in group 6 ... group 6 done ... source files in group 7 ... /etc/init.d/S73-capitcp /etc/init.d/S76-media /etc/init.d/S75-inetd /etc/init.d/S79-boxnotify [ 35.140000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0 Jan 1 01:00:35 ddnsd[975]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:35 ddnsd[975]: starting ... Jan 1 01:00:35 ddnsd[1012]: DDNS: no valid accounts Jan 1 01:00:35 ddnsd[1012]: [1012] Start failed Jan 1 01:00:35 pcpd[1017]: already running exceute files in group 7 ... group 7 done ... source files in group 8 ... /etc/init.d/S85-apps Jan 1 01:00:35 telefon[899]: Stop DECT [ 35.900000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 [ 35.900000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 exceute files in group 8 ... group 8 done ... source files in group 9 ... /etc/init.d/S99-tail rc.wlan: Start WLAN... rc.wlan start: WLAN daemon already running run_clock demon started AVM_WATCHDOG: System Init UEberwachung abgeschlossen (208070 ms noch verfuegbar) [ 36.120000] SysRq : Changing Loglevel Loglevel set to 4 Info: have to stop cat /dev/debug. notifyd[1030]: received signal Hangup pbd[793]: received signal Hangup Please press Enter to activate this console. Jan 1 01:00:40 usermand[1144]: starting ... Jan 1 01:00:40 contfiltd[1158]: starting ... Jan 1 01:00:49 ddnsd[1399]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:49 ddnsd[1399]: starting ... Jan 1 01:00:49 ddnsd[1401]: DDNS: no valid accounts Jan 1 01:00:49 ddnsd[1401]: [1401] Start failed Jan 1 01:00:49 pcpd[1403]: already running telefon: SIGCHLD PID 1043 received! telefon: SIGCHLD PID 934 received! starting pid 1068, tty '/dev/ttyS1': '-/bin/sh' BusyBox v1.20.2 (2015-07-07 11:46:25 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. ermittle die aktuelle TTY tty is "/dev/ttyS1" Serielles Terminal disable start/stop characters and flowcontrol # ifconfig adsl Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:2000 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ath0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:41 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:213 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) dsl Link encap:Point-to-Point Protocol inet addr:192.168.178.1 P-t-P:192.168.178.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:60 overruns:0 frame:0 TX packets:245 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:86164 (84.1 KiB) guest Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:192.168.179.1 Bcast:192.168.179.255 Mask:255.255.255.0 UP BROADCAST ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lan Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:192.168.178.1 Bcast:192.168.178.255 Mask:255.255.255.0 inet6 addr: fe80::3631:c4ff:fe56:c93f/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:60 errors:0 dropped:0 overruns:0 frame:0 TX packets:245 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7992 (7.8 KiB) TX bytes:85120 (83.1 KiB) lan:0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:169.254.1.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:786 errors:0 dropped:0 overruns:0 frame:0 TX packets:786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:347944 (339.7 KiB) TX bytes:347944 (339.7 KiB) wifi0 Link encap:UNSPEC HWaddr 34-31-C4-56-C9-41-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2704 errors:0 dropped:0 overruns:0 frame:0 TX packets:692 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:24 Memory:b8000000-b8010000 # iwconfig lo no wireless extensions. tunl0 no wireless extensions. Warning: Driver for device eth0 has been compiled with an ancient version of Wireless Extension, while this program support version 11 and later. Some things may be broken... eth0 ESSID:off/any Nickname:"" NWID:off/any Mode:Unknown/bug Channel:0 Access Point: 00:01:00:00:00:00 Bit Rate:8.38861 Mb/s Sensitivity:2146438480/0 RTS thr:off Fragment thr:off Encryption key:<too big> Power Management:on adsl no wireless extensions. lan no wireless extensions. guest no wireless extensions. dsl no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11ng ESSID:"FRITZ!Box 7312" Mode:Master Frequency:2.412 GHz Access Point: 34:31:C4:56:C9:41 Bit Rate:300 Mb/s Tx-Power:19 dBm RTS thr:off Fragment thr:off Encryption key:203D-3334-DA21-24DC-A1DD-1B23-8298-6A9E [2] Security mode:open Power Management:off Link Quality=94/94 Signal level=-96 dBm Noise level=-95 dBm Rx invalid nwid:10 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 printenv CONFIG_WLAN=y CONFIG_WLAN_RADIOSENSOR=y CONFIG_FON_HD=y CONFIG_USB_STORAGE_USERS=n CONFIG_TIMERCONTROL=y CONFIG_BETA_RELEASE=0 CONFIG_EWETEL_SMARTMETER=n CONFIG_USB_HOST_AVM=n CONFIG_LFS=y CONFIG_PERL=n CONFIG_FON_IPPHONE=y CONFIG_LTE=n CONFIG_I2C=n CONFIG_VPN_CERTSRV=n CONFIG_UTF8_FULL=y CONFIG_AB_COUNT=1 CONFIG_WLAN_TXPOWER=y CONFIG_CAPI_NT=n CONFIG_ONLINEHELP_URL=http://help.avm.de/fritzbox.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_NFS_CLI=n CONFIG_UDEV=y CONFIG_WLAN_OPENWIFI=n CONFIG_ATA_NOPASSTHROUGH=n CONFIG_JFFS2=y CONFIG_T38=y USER=root CONFIG_STOREUSRCFG=y CONFIG_NFS=n CONFIG_USB_TETHERING=n CONFIG_KIDS_CONTENT=n CONFIG_LED_EVENTS=y CONFIG_CODECS_IN_PCMROUTER=y CONFIG_CAPI_XILINX=y CONFIG_UBIK2=n CONFIG_SQLITE=n CONFIG_NEUERUL=y CONFIG_WLAN_ATH_NM_MAGPIE=n CONFIG_WEBGUI_PASS=n CONFIG_CHRONY=y CONFIG_FONGUI2=y CONFIG_CONFIGD=y CONFIG_DSL_UR8=n CONFIG_WLAN_WDS_NO_SLAVE=n CONFIG_TAM_ONRAM=n CONFIG_FONQUALITY=y CONFIG_SQLITE_VIDEO=n CONFIG_FTP=n CONFIG_USB=n CONFIG_GPS=n HOME=/ GCOV_PREFIX=/var/gcov OEM=1und1 CONFIG_MULTI_COUNTRY=n CONFIG_VDSL=n CONFIG_NCURSES=n CONFIG_PRODUKT_NAME=FRITZ!Box 7312 (UI) CONFIG_ENVIRONMENT_PATH=/proc/sys/urlader CONFIG_DECT_AUDIOD=y CONFIG_DECT_NO_EMISSION=y CONFIG_C4=n CONFIG_USB_HOST_TI=n ethaddr=34:31:C4:56:C9:3F CONFIG_AVMIPC_REMOTE_IP= CONFIG_PROV_DEFAULT=n CONFIG_ASSIST=y CONFIG_SWAP=y CONFIG_HOME_AUTO=n CONFIG_LED_NO_DSL_LED=y CONFIG_NTFS=n CONFIG_MANUAL_URL=https://assets.avm.de/manual/?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_SUBVERSION= CONFIG_VERSION=06.54 CONFIG_DIAGNOSE_LEVEL=0 CONFIG_USB_STORAGE=n CONFIG_USB_INTERNAL_HUB=n CONFIG_CAPI_POTS=n HWRevision_ATA=1 CONFIG_SAMBA=n CONFIG_WEBSRV=y CONFIG_USB_XHCI=n CONFIG_RELEASE=1 CONFIG_BLUETOOTH_CTP=n CONFIG_DECT_MONI_EX=y Language_is_default=yes CONFIG_ROMSIZE=16 CONFIG_FIRMWARE_URL=http://www.avm.de/fritzbox-firmware-update.php?hardware=189&oem=1und1&language=de&country=049 CONFIG_SERVICEPORTAL_URL=http://www.avm.de/fritzbox-service-portal.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_FLASH_DOUBLE=n CONFIG_PRODUKT=Fritz_Box_HW189 CONFIG_DECT_FW_ULE=n HWRevision=189 HWRevision_BitFileCount= ANNEX=B CONFIG_NO_EXTENDED_CODECS=y CONFIG_BUTTON=y CONFIG_ACCESSORY_URL=http://www.avm.de/fritzbox_apps.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_VERSION_MAJOR=117 CONFIG_MAILD=y CONFIG_XILINX=y CONFIG_TR064=y CONFIG_MEDIASRV_MOUNT=n CONFIG_CXX=n CONFIG_WLAN_ATH_NM_COMBO=n CONFIG_BOXLOWRESSOURCES=y CONFIG_DOCSIS_PCD_NO_REBOOT=n CONFIG_ONLINEHELP=y CONFIG_NQOS=y Country_is_default=yes CONFIG_VPN=y CONFIG_USB_PRINT_SERV=n CONFIG_GDB=n CONFIG_UPNP=y CONFIG_ETH_COUNT=1 CONFIG_USB_LTE=n CONFIG_WEBDAV=n CONFIG_CAPI=y TERM=vt102 CONFIG_MAILER=n CONFIG_TR069=y CONFIG_DSL_2DP=n CONFIG_WLAN_GUEST=y CONFIG_CDROM_FALLBACK=n CONFIG_PLUGINV2=n CONFIG_ONLINEPB=y CONFIG_USB_GSM=n CONFIG_FAXSEND=y CONFIG_WLAN_WEATHER_CAC=n CONFIG_PLC_DETECTION=y nor_size=16MB CONFIG_FHEM=n CONFIG_USB_GSM_VOICE=n CONFIG_WLAN_WDS=n CONFIG_DECT=y PATH=/sbin:/usr/sbin:/bin:/usr/bin CONFIG_WLAN_1130TNET=n CONFIG_CAPI_UBIK=n CONFIG_TELEKOM_KOFFER=n CONFIG_RAMDISK=n CONFIG_NAND=n CONFIG_MTD_MAILSEND=y CONFIG_INSTALL_TYPE=mips34_16MB_dect441_1eth_1ab_wlan11n_40508 CONFIG_DECT_PICTURED=y CONFIG_FAXSUPPORT=y enable_ata=1 CONFIG_WLAN_MADWIFI=y CONFIG_HOME_AUTO_NET=n CONFIG_MULTI_LANGUAGE=n CONFIG_QOS_METER=y CONFIG_WLAN_ATH_NM_PCI=y CONFIG_DECT_HOME=n CONFIG_SRTP=n CONFIG_IGD=y CONFIG_CONFIGSPACE_ONNAND=n CONFIG_UNIQUE_PASSWD=n CONFIG_WLAN_WMM=y CONFIG_DECT_ONOFF=n CONFIG_OEM_DEFAULT=avm CONFIG_EXT2=n CONFIG_PLUGINV2_WEBCM_INTERPRETER=n CONFIG_FAX2MAIL=y CONFIG_MEDIASRV=n CONFIG_MYFRITZ=y CONFIG_ATA=y CONFIG_HOMEI2C=n CONFIG_ERR_FEEDBACK=y CONFIG_EXT3=n CONFIG_BOX_FEEDBACK=y CONFIG_AUDIO=n CONFIG_BASIS=y CONFIG_SQLITE_BILDER=n CONFIG_VLYNQ=n CONFIG_DSL_MULTI_ANNEX=n CONFIG_IPV6=y CONFIG_WLAN_1350TNET=n CONFIG_VOIP_ENUM=n CONFIG_ECO=y CONFIG_INETD=y CONFIG_USB_HOST_INTERNAL=n CONFIG_LOGD=n SHELL=/bin/sh CONFIG_WLAN_IPTV=y CONFIG_USB_WLAN_AUTH=n CONFIG_CDROM=n CONFIG_NOTELNETD=n CONFIG_VOL_COUNTER=y CONFIG_WLAN_EACS=y CONFIG_REMOTE_HTTPS=y CONFIG_GDB_FULL=n CONFIG_HOSTNAME=fritz.box CONFIG_UTF8=y CONFIG_MEDIACLI=y CONFIG_USB_STORAGE_SPINDOWN=n CONFIG_LIB_MATH=y CONFIG_ECO_SYSSTAT=y CONFIG_DOCSIS_CLI=n CONFIG_AUTOUPDATE=n CONFIG_USB_HOST=n CONFIG_DOCSIS=n CONFIG_AURA=n CONFIG_MAILER2=y CONFIG_DECT_14488=y ETC_CONFIG_PATH=/etc/init.d/rc.init CONFIG_WLAN_TCOM_PRIO=n CONFIG_PLUGINV2_WLAN=n Language=de CONFIG_UPDATEFEATURE_URL=https://www.avm.de/fritzbox_firmware-features.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_DECT2=y CONFIG_WLAN_WDS2=n CONFIG_WEBCM_INTERPRETER=y CONFIG_SESSIONID=y CONFIG_KIDS=y CONFIG_MTD_RSS=y CONFIG_CAPI_TE=n CONFIG_WLAN_HOTSPOT=n CONFIG_NEWSLETTER_URL=http://www.avm.de/newsletter?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_LABOR_DSL=n CONFIG_WLAN_WPS=y CONFIG_DECT_MONI=y CONFIG_ANNEX=B CONFIG_WEBUSB=n CONFIG_SOCAT=n PWD=/ CONFIG_DSL_VENDORID= CONFIG_MINI=n CONFIG_PLC=n CONFIG_LINEARTV=n Country=049 CONFIG_ETH_GBIT=n CONFIG_VLYNQ0=0 CONFIG_TAM_MODE=1 CONFIG_WLAN_GREEN=y GCOV_PREFIX_STRIP=5 TZ=CET-1CEST-2,M3.5.0/02:00:00,M10.5.0/03:00:00 CONFIG_PPA=y CONFIG_WLAN_SAVEMEM=n CONFIG_GDB_SERVER=n CONFIG_VLYNQ1=0 CONFIG_MTD_MAIL=y CONFIG_CAPI_MIPS=n CONFIG_FONBOOK2=y OEM_DEFAULT_INDEX= CONFIG_NAS=n CONFIG_WLAN_ATH_NM_USB=n CONFIG_WLAN_ATH_NM_OFFLOAD=n CONFIG_NFS_SRV=n CONFIG_MORPHSTICK=n CONFIG_BLUETOOTH=n CONFIG_ATA_FULL=n CONFIG_LUA=y CONFIG_TAM=y CONFIG_SPEECH_FEEDBACK=y CONFIG_LLTD=n CONFIG_SDK=n CONFIG_RAMSIZE=64 CONFIG_FON=y CONFIG_LIBZ=y CONFIG_DECT_CATIQ20=n CONFIG_DSL=y CONFIG_IPTV_4THOME=y HWSubRevision=1


(OEM) EVA Revision: 1.1322 Version: 2322

FritzOS 06.03 ref 117

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1322 Version: 2322 (C) Copyright 2005 AVM Date: Dec 16 2011 Time: 14:45:22 (1) 2 0x0-0x341D [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz Atheros 8030 detected Eva_AVM >........................... Lantiq xDSL CPE AR9 [ifx_enhance_phy_clock] PLL0_CFG: 0x00b0660b [ifx_enhance_phy_clock] PLL0 already modified. [ 0.000000] Linux version 2.6.32.60 (hjortmann@EmbeddedVM) (gcc version 4.6.3 (Buildroot 2011.11) ) #3 Thu Dec 5 14:42:47 CET 2013 [ 0.000000] phym = 04000000, mem = 04000000, max_pfn = 00004000 [ 0.000000] Reserving memory for CP1 @0xa4000000, size 0x00000000 [ 0.000000] wlan_mem_start = 0x03f9e000 [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 804d2000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001954c (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00003f9e [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00003f9e [ 0.000000] [c55] c55_mem_start = 0xfc0000 [ 0.000000] [module-alloc-by-name] 'modulemem' not in use, use AVM Kernel Config (6402048 bytes, reserved for module mem) [ 0.000000] [module-alloc] use 0x61b000 bytes at 0x81081000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16158 [ 0.000000] Kernel command line: console=ttyS1,115200n8r nor_size=16MB ethaddr=9C:C7:A6:A5:96:1E [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=189 to write through [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0002c000 [ 0.000000] Readback ErrCtl register=0002c000 [ 0.000000] Memory: 52520k/65144k available (3412k kernel code, 12552k reserved, 1519k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] [mips_cpu_irq_init] irq_base 0 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 261.32 BogoMIPS (lpj=1306624) [ 0.230000] Security Framework initialized [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] kernel_init: started [ 0.240000] kernel_init: kernel locked [power_managment_setup] reset 'DSL, DFE, AFE, VOICE, DSLTC, ARC' [power_managment_setup] reset 'LDO' [power_managment_setup] power down 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0' [power_managment_setup] power down 'MSI1, PDI1 PCIE1 PCIE1_PHY' [power_managment_setup] disable power domain 'DSL + DFE' [ 0.270000] NET: Registered protocol family 16 [ 0.280000] Reboot Status: (c) AVM 2013, Reboot Status is: Software-Reboot(c) AVM 2013, Reboot Status is: Software-Reboot(c) AVM 2013, Reboot Status is: Software-Reboot [ 0.290000] Reboot Status is: Soft-Reboot [ 0.290000] [avmnet] [avmnet_cfg_init] Driver version: 6.106.1.2 - Revision 1496:2498 - Do 5.12.2013 14:42:21 [ 0.300000] Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.310000] bio: create slab <bio-0> at 0 [ 0.310000] pci 0000:00:00.0: PME# supported from D1 D2 [ 0.320000] pci 0000:00:00.0: PME# disabled [ 0.320000] NET: Registered protocol family 8 [ 0.320000] NET: Registered protocol family 20 [ 0.330000] NET: Registered protocol family 2 [ 0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.340000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.340000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.350000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.360000] TCP reno registered [ 0.360000] NET: Registered protocol family 1 [ 0.360000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 [ 0.360000] ,(c)2009 Infineon Technologies AG [ 0.360000] skb_shared_size:344 [ 0.380000] I[avm_register_busmaster:125]: Registered busmaster device: AVM_DMA_BUSMASTER [ 0.380000] [bcu_control_interrupt] 'FPI Slave BCU0' Error Interrupt [ 0.380000] Slave BCU[sBCU_EADD]: Error Address Register: 0x17000004 [ 0.380000] Slave BCU[sBCU_EDAT]: Error Data Capture Register: 0x0290030f [ 0.380000] Slave BCU[sBCU_CON] : Control Register: 0x4009ffff [ 0.380000] Slave BCU[sBCU_ECON]: Error Register (0x21be0030): [ 0.380000] FPI Bus Operation Code 0x2 [ 0.380000] FPI Bus Tag Number 0x1 [ 0.380000] FPI Bus Read Signal: passive [ 0.380000] FPI Bus Write Signal: active [ 0.380000] FPI Bus Supervisor Mode: active [ 0.380000] FPI Bus Acknowladge Signal: 0x3 [ 0.380000] FPI Bus Abort: passive [ 0.380000] FPI Bus Ready: active [ 0.380000] FPI Bus Timeout: not pressed [ 0.380000] FPI Bus Error Counter: 48 [ 0.450000] [bcu_control_init] interrupts for BCU installed [ 0.460000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.470000] clk-timing: timing:16, ram_refresh_timing:1524, base_ram_refresh_timing:7775 [ 0.480000] smvp_tc_init: tc 0 tcbind 00020000 tcstatus 18102000 [ 0.480000] smvp_tc_init: tc 1 tcbind 00200001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 2 tcbind 00400001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 3 tcbind 00600001 tcstatus 00000400 [ 0.480000] config3 0x424 MT 1 [ 0.480000] MVPControl 0x2, STLB 0 VPC 1 EVP 0 [ 0.480000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1 [ 0.510000] initcall 0x804d98fc returned with disabled interrupts [ 0.520000] audit: initializing netlink socket (disabled) [ 0.520000] type=2000 audit(0.000:1): initialized [ 0.530000] [simple_profiling] 0 entries 50 min [ 0.530000] squashfs: version 3.4 (2008/08/26) Phillip Lougher [ 0.540000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.550000] fuse init (API version 7.13) [ 0.550000] msgmni has been set to 102 [ 0.560000] io scheduler noop registered (default) [ 0.560000] [avm_membench_init] [ 0.860000] avm_net_trace: Up and running. [ 0.860000] [loadcontrol] set auto - scale=1 [ 0.870000] [avm] configured: watchdog event debug [ 0.870000] [ 0.870000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Dec 5 2013 14:42:03) [ 0.880000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 0.890000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 0.900000] Setup tcs=0x1 current_tc_mask=0x1, reg=0 [ 0.910000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 0.920000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 0.930000] Setup tcs=0x1 current_tc_mask=0x1, reg=1 [ 0.930000] [avm]: AVM Simple Profiling enabled. [ 0.940000] ifx_pmu_init: Major 245 [ 0.940000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.950000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.960000] Infineon Technologies RCU driver version 1.0.7 [ 0.960000] ttyS0 at MMIO 0x1e100400 (irq = 100) is a PORT_IFX_ASC [ 0.970000] ttyS1 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 0.980000] loop: module loaded [ 0.980000] nbd: registered device at major 43 [ 0.980000] [0]system-load 1 loadavg 0.0 0.0 0.0 - 13 tasks:0 % curr:swapper(0 %) max:swapper(0 %, pid:1), readytorun: 1, pgfault 0/s (max 0 avg 0.0) [ 1.020000] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 1.020000] Platform NOR MTD, (c) AVM 2010 [ 1.020000] [plat_nor_probe]start probe [ 1.030000] [do_map_probe] driver_name=cfi_probe [ 1.030000] mtd-nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 1.040000] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.040000] mtd-nor: CFI does not contain boot bank location. Assuming top. [ 1.050000] number of CFI chips: 1 [ 1.050000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 1.060000] [ifx_jffs2_parser_function] mtd_info->name mtd-nor mtd_info->index 0 param=0 p_mtd_pat=0x83a1a954 [ 1.070000] [ifx_jffs2_parser_function] try partition kernel (offset 0x20000 len 16121856) [ 1.080000] [ifx_jffs2_parser_function] magic 19852003 found @pos 0xd80000, size 2097152 [ 1.090000] [ifx_squashfs_parser_function] mtd_info->name mtd-nor mtd_info->index 0 param=0 p_mtd_pat=0x83a1a954 [ 1.120000] [ifx_squashfs_parser_function:320] pos: 0x17a900 | offs[0]: 0x17a900 | size[0]: 14702336 | offs[1]: 0x20000 | size[1]: 1419520 [ 1.130000] [ifx_squashfs_parser_function] magic found @pos 0x17a900 [ 1.130000] 6 find_squashfs partitions found on MTD device mtd-nor [ 1.140000] Creating 6 MTD partitions on "mtd-nor": [ 1.140000] 0x00000017a900-0x000000f80000 : "rootfs" [ 1.150000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.160000] {ifx_mtd_add_notifier} name rootfs [ 1.170000] 0x000000020000-0x00000017a900 : "kernel" [ 1.170000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.180000] {ifx_mtd_add_notifier} name kernel [ 1.190000] 0x000000000000-0x000000020000 : "urlader" [ 1.190000] {ifx_mtd_add_notifier} name urlader [ 1.200000] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 1.200000] {ifx_mtd_add_notifier} name tffs (1) [ 1.210000] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 1.210000] {ifx_mtd_add_notifier} name tffs (2) [ 1.220000] 0x000000d80000-0x000000f80000 : "jffs2" [ 1.220000] {ifx_mtd_add_notifier} name jffs2 [ 1.230000] {ifx_mtd_add_notifier} name mtd-nor [ 1.230000] mtd-nor mtd-nor: registered mtd device [ 1.240000] Lantiq SSC driver, version 2.4.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.240000] Unknown SPI device: 0xFF 0xFF 0xFF [ 1.250000] ifx_spi_flash_init: Found no serial flash device [ 1.250000] tun: Universal TUN/TAP device driver, 1.6 [ 1.260000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.270000] IFX SWITCH API, Version 1.1.8.5 [ 1.270000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.380000] mice: PS/2 mouse device common for all mice [ 1.380000] i2c /dev entries driver [ 1.390000] CAPI Subsystem Rev 1.1.2.8 [ 1.390000] AVM PA 4.1.3 2013-11-18 [ 1.390000] AVM PA skb pktinfo at offset 128 size 192 [ 1.400000] [loadcontrol]module avm_pa registered [ 1.400000] IPv4 over IPv4 tunneling driver [ 1.410000] TCP cubic registered [ 1.410000] mcfw: IGMPv3 fast forwarding [ 1.410000] NET: Registered protocol family 10 [ 1.420000] IPv6 over IPv4 tunneling driver [ 1.420000] NET: Registered protocol family 17 [ 1.430000] NET: Registered protocol family 8 [ 1.430000] atmpvc_init() failed with -17 [ 1.430000] KOAM is loaded successfully. [ 1.440000] l2tp_core: L2TP core driver, V2.0 [ 1.440000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.450000] l2tp_netlink: L2TP netlink interface [ 1.450000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.460000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.470000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0) [ 1.470000] mount on mtd3 and mtd4 (double buffering) [ 1.480000] Adam2 environment variables API installed. [ 1.480000] {avmnet_cfg_netinit} [ 1.490000] [avmnet] No config found for HWRev 189, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev [ 1.500000] [avmnet] No config found for HWRev 189, HWSubRev 1, trying base config for HWRev [ 1.510000] {avmnet_mac_ar9_init} Init on module mac_ar9_0 called. [ 1.520000] [avmnet] [avmnet_mac_ar9_setup] IFX_AR9_ETH_CTL(0): 0x424001 [ 1.530000] [avmnet] [avmnet_mac_ar9_setup] mac_nr: 0, vlan_reg: 0x4070001 [ 1.660000] [avm_pa_multiplexer_init] start [ 1.660000] [avm_pa_multiplexer_init] init complete [ 1.660000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 9c:c7:a6:a5:96:1e [ 1.670000] kernel_init: basic setup done [ 1.680000] [squashfs] use lzma compression [ 1.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:0. [ 1.690000] Freeing unused kernel memory: 176k freed [ 1.740000] trying /sbin/init starting pid 112, tty '/dev/ttyS1': '/etc/init.d/rc.S' tar: removing leading '/' from member names source files in group 0 ... /etc/init.d/S00-signal /etc/init.d/S05-watchdog /etc/init.d/S09-rtc /etc/init.d/S01-head /etc/init.d/S08-tffs /etc/init.d/S02-led /etc/init.d/S09-config [ 2.740000] TFFS Name Table K [ 4.250000] [module-alloc-by-name] give 0x11000 bytes at 0x81081000 to module 'led_modul_Fritz_Box_HW189' (0x60a000 bytes left) [ 4.260000] led_modul_Fritz_Box_HW189: module license ' [ 4.260000] (C) Copyright 2012 by AVM [ 4.260000] ' taints kernel. [ 4.270000] Disabling lock debugging due to kernel taint [ 4.290000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 4.300000] AVM_WATCHDOG: System Init UEberwachung 240 Sekunden mknod: /var/flash/ar7.cfg: File exists P-Defaults: do nothing [ 4.850000] [module-alloc-by-name] give 0x1000 bytes at 0x81092000 to module 'rtc_avm' (0x609000 bytes left) [ 4.870000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 4.880000] [avm-rtc]: avm_rtc_probe: register: ret=0x83063400 [ 4.880000] [avm-rtc]: avm_rtc_probe: success exceute files in group 0 ... /etc/init.d/E05-basemodules group 0 done ... source files in group 1 ... /etc/init.d/S10-html /etc/init.d/S12-default /etc/init.d/S10-vm /etc/init.d/S15-filesys /etc/init.d/S11-config_def /etc/init.d/S17-capi /etc/init.d/S11-piglet /etc/init.d/S17-tam [ 5.110000] [ 5.110000] [avm_debug]redirect kernel-messages (/dev/debug) [ 5.170000] [module-alloc-by-name] give 0x8000 bytes at 0x81093000 to module 'Piglet_noemif' (0x601000 bytes left) [ 5.170000] [module-alloc-by-name] 0x8000 bytes used, 0xAB30 bytes expected [ 5.180000] [piglet]use default-settings (1 gpio from hw_config) [ 5.320000] patch_dectfw: C025D000, totallen = 42434(A5C2) [ 5.320000] patch_dectfw: patch_adress: A0 max_len: 26 with Version 2 Len: 17 [ 5.320000] patch_dectfw: dectmode 1 [ 5.320000] dect_loader: slow-bootmode <FE>* ********************************************************************************** [ 8.510000] dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull [ 10.520000] [piglet]TDM: FS: 8005 Hz CLK: 1024005 Hz checkempty: : No such file or directory [jffs2] Mount /data success (mtd5 size 2097152) [jffs2] write env variable jffs2_size to 32 [ 11.010000] [module-alloc-by-name] give 0x5D000 bytes at 0x8109B000 to module 'pcmlink' (0x5A4000 bytes left) [ 11.010000] [module-alloc-by-name] 0x5D000 bytes used, 0x65E18 bytes expected [pcmlink]svn: 1922 [ 11.120000] [pcmlink]VPE-Interface: base 0xFC0000, maxsize 131072, host-irq 142 [ 11.510000] [0]system-load 6 loadavg 0.15 0.3 0.1 - 23 tasks:30 % curr:modprobe(4 %) max:init(10 %, pid:1), readytorun: 1, pgfault 1927/s (max 1 avg 1.0) [ 11.640000] [module-alloc-by-name] give 0xB2000 bytes at 0x810F8000 to module 'isdn_fbox_fon5' (0x4F2000 bytes left) [ 11.640000] [module-alloc-by-name] 0xB2000 bytes used, 0xC7608 bytes expected [ 11.730000] [isdn]svn:3066 [ 11.730000] driver params overwritten io_addr=0x0 irq_num=0 [ 11.730000] [pcmlink]chrony-support [ 11.740000] VPE loader: loading segment 1 to 80FC0000 (14000 bytes) elf loaded [ 11.740000] vpe_run: tc 1 start-addr 80FC0000 [ 11.740000] vpe_run: tc 1 tcstatus 18002000 tcbind 00200001 MVPCONTROL 00000002 vpeopt 00000000 [ 12.750000] PCMLINK: Version 7.498 Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222) no HwCross DSP-EC: 2 [ 13.230000] [module-alloc-by-name] give 0x54000 bytes at 0x811AA000 to module 'capi_codec' (0x49E000 bytes left) [ 13.230000] [module-alloc-by-name] 0x54000 bytes used, 0x5DA80 bytes expected capicodec_init() [capi_codec] support fax [capi_codec] support Codecs [ 13.450000] [module-alloc-by-name] give 0x35000 bytes at 0x811FE000 to module 'avm_dect' (0x469000 bytes left) [ 13.450000] [module-alloc-by-name] 0x35000 bytes used, 0x3D3EC bytes expected [ 13.480000] [DECTDRV_ERR] avm_dect driver init [ 13.480000] [DECTDRV_ERR] [avm_dect]avm_dect_thread: start [ 13.490000] [module-alloc-by-name] give 0x3000 bytes at 0x81233000 to module 'dect_io' (0x466000 bytes left) [ 13.490000] [module-alloc-by-name] 0x3000 bytes used, 0x454C bytes expected TAM: create JFFS2 directory /data/tam [ 13.520000] dect_uicp_from_dect, ignore 8 bytes, dect_manager not up: 2F 7B exceute files in group 1 ... /etc/init.d/E15-device mknod led c 242 mknod tffs c 243 [ 13.610000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 mknod avm_power c 252 mknod debug c 248 mknod avm_event c 249 mknod capi_oslib c 68 mknod dect_io c 227 / group 1 done ... source files in group 2 ... /etc/init.d/S21-udev exceute files in group 2 ... group 2 done ... source files in group 3 ... /etc/init.d/S30-ledcfg exceute files in group 3 ... group 3 done ... source files in group 4 ... /etc/init.d/S40-swap /etc/init.d/S44-hostname /etc/init.d/S48-configd /etc/init.d/S42-ptest /etc/init.d/S46-usb Jan 1 01:00:13 udevd[355]: specified group 'tty' unknown Jan 1 01:00:13 udevd[355]: specified group 'dialout' unknown Jan 1 01:00:13 udevd[355]: specified group 'kmem' unknown Jan 1 01:00:13 udevd[355]: specified group 'video' unknown Jan 1 01:00:13 udevd[355]: specified group 'audio' unknown Jan 1 01:00:13 udevd[355]: specified group 'lp' unknown Jan 1 01:00:13 udevd[355]: specified group 'disk' unknown Jan 1 01:00:13 udevd[355]: specified group 'floppy' unknown Jan 1 01:00:13 udevd[355]: specified group 'cdrom' unknown Jan 1 01:00:13 udevd[355]: specified group 'tape' unknown [ 14.020000] [module-alloc-by-name] give 0x1000 bytes at 0x81236000 to module 'lzo_compress' (0x465000 bytes left) [ 14.020000] [module-alloc-by-name] 0x1000 bytes used, 0x1888 bytes expected [ 14.050000] [module-alloc-by-name] give 0x1000 bytes at 0x81237000 to module 'lzo_decompress' (0x464000 bytes left) [ 14.050000] [module-alloc-by-name] 0x1000 bytes used, 0x1908 bytes expected [ 14.100000] [module-alloc-by-name] give 0x4000 bytes at 0x81238000 to module 'ramzswap' (0x460000 bytes left) [ 14.100000] [module-alloc-by-name] 0x4000 bytes used, 0x5F00 bytes expected [ 14.120000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192mknod: /dev/ramzswap0: File exists [ 14.160000] Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS exceute files in group 4 ... /etc/init.d/E40-dsl /etc/init.d/E46-net /etc/init.d/E47-voip [dsl get xtse] ANNEX=B [dsl get xtse] setting Annex B and J [dsl get xtse] 10 00 10 40 00 04 01 00 [dsl sus] starting ar9 dsp... [dsl sus] ANNEX=B DIAGNOSE=no [ 15.270000] [module-alloc-by-name] give 0x9000 bytes at 0x8123C000 to module 'ifxmips_mei' (0x457000 bytes left) [ 15.270000] [module-alloc-by-name] 0x9000 bytes used, 0xBCAC bytes expected [dsl mei] Lantiq MEI driver version: 5.03.00 [dsl mei] Lantiq MEI driver global debug_level: 0 [dsl sus] loaded ar9 mei driver: ifxmips_mei.ko with params: [ 15.530000] [module-alloc-by-name] give 0x4C000 bytes at 0x81245000 to module 'drv_dsl_cpe_api' (0x40B000 bytes left) [ 15.530000] [module-alloc-by-name] 0x4C000 bytes used, 0x559A0 bytes expected [dsl drv] Lantiq CPE API Driver version: DSL CPE API V4.9.2.1 [dsl drv] Predefined debug level: 4 [dsl drv] dynamically registered major number 239 for drv_dsl_cpe_api [dsl sus] loaded ar9 dsl driver: drv_dsl_cpe_api.ko with params: [dsl sus] created ar9 dsl device node /dev/dsl_ar9 (major: 239 , minor: 0) [dsl sus] created ar9 mei device node /dev/ifx_mei (major: 105 , minor: 0) [dsl sus] started dsl_control (configuration: -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.sh ) nohup: appending output to nohup.out 0 [dsl sus] started dsl_monitor [dsl sus] ....ar9 dsp started [ 17.560000] [module-alloc-by-name] give 0x11E000 bytes at 0x81291000 to module 'kdsldmod' (0x2ED000 bytes left) [ 17.560000] [module-alloc-by-name] 0x11E000 bytes used, 0x14A6A4 bytes expected [ 17.670000] kdsldmod: init start (Feb 7 2014 15:25:04) sizeof(struct sk_buff)=440 [ 17.680000] userman: device registerd (userman_url) with major=233 <6>kdsld: ttychannel: ldisc 8 registered [ 17.680000] kdsldmod: init done [ 18.600000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 Jan 1 01:00:18 l2tpv3d[571]: starting. Jan 1 01:00:18 l2tpv3d[571]: verbose: DISABLED [ 21.280000] ADDRCONF(NETDEV_UP): lan: link is not ready [ 21.290000] ADDRCONF(NETDEV_UP): guest: link is not ready [avm_power] eth: port 0 force normal CON t0 [avm_power] eth: port 1 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 1 [ 21.940000] [avm_power] : ethernet switch failed [avm_power] eth: port 2 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 2 [ 21.940000] [avm_power] : ethernet switch failed [avm_power] eth: port 3 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 3 [ 21.940000] [avm_power] : ethernet switch failed [ 22.110000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.110000] device eth0 entered promiscuous mode Jan 1 01:00:21 multid[590]: DHCPD on lan:0 skipped, is virtual interface rc.wlan: Start WLAN... [ 22.710000] DSP: XDU=1( D1 ) OVR=0 MIPS_OVR=0 [ 22.810000] [0]system-load 9 loadavg 0.36 0.8 0.3 - 59 tasks:38 % curr:wland(0 %) max:mtdblockd(13 %, pid:86), readytorun: 2, pgfault 3655/s (max 2 avg 1.0) WLAND:[00609]:01:00.22:Build = Dec 5 2013 14:33:42 [ 23.590000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 Jan 1 01:00:23 dsld[613]: startup ($Revision: 1.95 $$CompileDate: Feb 7 2014 15:23:27 $) Jan 1 01:00:23 dsld[613]: set_preconfig1 Jan 1 01:00:23 dsld[613]: sync_group in ar7.cfg: Jan 1 01:00:23 dsld[613]: sync_group:sync_dsl(enabled=1), nr=0 Jan 1 01:00:23 dsld[613]: vcc:1/32 Jan 1 01:00:23 dsld[613]: dsliface:internet Jan 1 01:00:23 dsld[613]: dsliface:voip Jan 1 01:00:23 dsld[613]: sync_group: dsl Jan 1 01:00:23 dsld[613]: sync_dsl is igd_device Jan 1 01:00:23 dsld[613]: set_preconfig2 Jan 1 01:00:23 dsld[613]: add_vcc_connection: dsl Jan 1 01:00:23 dsld[617]: DSL Mac 9c:c7:a6:a5:96:21 Jan 1 01:00:23 dsld[617]: VOIP Mac 9c:c7:a6:a5:96:22 Jan 1 01:00:23 dsld[617]: VCC2 Mac 9c:c7:a6:a5:96:23 Jan 1 01:00:23 dsld[617]: VCC3 Mac 9c:c7:a6:a5:96:1f <3>kdsld: kdsld_vcc_preunregister: * Jan 1 01:00:24 dsld[617]: voip: ppptarget voip disabled, ignored [ 25.000000] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0 Jan 1 01:00:24 dsld[617]: sync_group(prepare_interfaces): dsl: inet_nr=0 Jan 1 01:00:24 dsld[617]: nach prepare_interfaces: dsld.dsliface_default_inet_nr=0, dsld.dsliface_voip_nr=-1 Jan 1 01:00:24 dsld[617]: get_queueindex: none: not found Jan 1 01:00:24 dsld[617]: get_queueindex: none: not found Jan 1 01:00:24 dsld[617]: queue 0: prio 0 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 1: prio 10 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 2: prio 20 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 3: prio 30 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 4: prio 100 weight 90 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 5: prio 100 weight 10 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 6: prio 200 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: appl 0: sip-appl result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sip" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark rtp" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sipdns,ntpdns,tr069dns,tr069" result 2 Jan 1 01:00:24 dsld[617]: classifer: local "localmark igmp" result 3 Jan 1 01:00:24 dsld[617]: classifer: local "localmark webdav" result 4 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 43962,47806" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "ip.proto IPv6-ICMP" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "ip.proto icmp" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 53" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 5060" result 5 Jan 1 01:00:24 dsld[617]: classifer: lan "dhcpoption 12 FRITZ!Media* mediatab" result 6 Jan 1 01:00:24 dsld[617]: classifer: lan "ethsrctab mediatab" result 6 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sip_internet" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark rtp_internet" result 1 Jan 1 01:00:24 dsld[617]: result 0: tos 65535 vprio 65535 queue 5 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 1: tos 65535 vprio 65535 queue 2 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 2: tos 65535 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 3: tos 65535 vprio 65535 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 4: tos 65535 vprio 65535 queue 6 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 5: tos 65535 vprio 65535 queue 2 appl 0 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 6: tos 65535 vprio 65535 queue 3 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: interface lo added. Jan 1 01:00:24 dsld[617]: interface lo up. Jan 1 01:00:24 dsld[617]: interface tunl0 added. Jan 1 01:00:24 dsld[617]: interface sit0 added. Jan 1 01:00:24 dsld[617]: interface eth0 added. Jan 1 01:00:24 dsld[617]: interface eth0 up. Jan 1 01:00:24 dsld[617]: interface adsl added. Jan 1 01:00:24 dsld[617]: interface lan added. Jan 1 01:00:24 dsld[617]: interface lan up. Jan 1 01:00:24 dsld[617]: interface guest added. Jan 1 01:00:24 dsld[617]: interface guest up. Jan 1 01:00:24 dsld[617]: interface hotspot added. Jan 1 01:00:24 dsld[617]: interface hotspot up. Jan 1 01:00:24 dsld[617]: start register_vccs_and_ifaces_on_kdsld for sync_dsl Jan 1 01:00:24 dsld[617]: setup_dslchannel: ifname= Jan 1 01:00:24 dsld[617]: kdsld_preregister_vcc: predsl1 <3>kdsld: kdsld_vcc_preregister: predsl1 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:24 dsld[617]: kdsld_preregister_vcc: kdsld_vccidx=0 Jan 1 01:00:24 dsld[617]: verbose: DISABLED Jan 1 01:00:25 telefon[631]: use clock_gettime(CLOCK_MONOTONIC)! Jan 1 01:00:25 telefon[631]: No S0NT! Jan 1 01:00:25 telefon[631]: NoOldMSNNames telefon: SIGCHLD PID 632 received! Jan 1 01:00:25 telefon[631]: WARNING No config file '/var/flash/fx_def' ! Jan 1 01:00:25 ctlmgr[577]: WLANLIB: my_wlan_init:649: svn revision 1493 Jan 1 01:00:25 telefon[631]: INFO No MOH file '/var/flash/fx_moh' ! Jan 1 01:00:25 ctlmgr[577]: WLANLIB: weak_wlan_check:63: Missing weak 'process_wlanmail'. telefon: SIGCHLD PID 645 received! group 4 done ... source files in group 5 ... exceute files in group 5 ... group 5 done ... source files in group 6 ... exceute files in group 6 ... group 6 done ... source files in group 7 ... /etc/init.d/S73-capitcp /etc/init.d/S75-inetd /etc/init.d/S76-media [ 28.550000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 exceute files in group 7 ... group 7 done ... source files in group 8 ... /etc/init.d/S85-apps exceute files in group 8 ... group 8 done ... source files in group 9 ... /etc/init.d/S99-tail [ 29.170000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0 [ 29.170000] [DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records) [ 29.170000] [DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records) run_clock demon started [ 29.560000] SysRq : Changing Loglevel Loglevel set to 4 Jan 1 01:00:29 telefon[638]: NoOldMSNNames mknod: /var/flash/fx_def: File exists telefon: SIGCHLD PID 679 received! Jan 1 01:00:29 telefon[638]: WARNING No config file '/var/flash/fx_def' ! Info: have to stop cat /dev/debug. [ 5.170000] [module-alloc-by-name] give 0x8000 bytes at 0x81093000 to module 'Piglet_noemif' (0x601000 bytes left) [ telefon: SIGHUP received! pbd[629]: received signal Hangup pbd[628]: received signal Hangup pbd[627]: received signal Hangup pbd[625]: received signal Hangup Please press Enter to activate this console. telefon: SIGHUP received! Jan 1 01:00:29 telefon[638]: Stop DECT starting pid 683, tty '/dev/ttyS1': '-/bin/sh' BusyBox v1.19.3 (2012-08-08 12:53:46 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. ermittle die aktuelle TTY tty is "/dev/ttyS1" Serielles Terminal # rc.wlan: Start WLAN... rc.wlan: WLAN daemon already running uname -a Linux fritz.fonwlan.box 2.6.32.60 #3 Thu Dec 5 14:42:47 CET 2013 mips GNU/Linux telefon: SIGCHLD PID 694 received! telefon: SIGCHLD PID 648 received!


cat /proc/cpuinfo

system type		: AR9
processor		: 0
cpu model		: MIPS 34Kc V4.12
BogoMIPS		: 261.32
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 16
extra interrupt vector	: yes
hardware watchpoint	: yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
ASEs implemented	: mips16 dsp mt
shadow register sets	: 1
core			: 0
VCED exceptions		: not available
VCEI exceptions		: not available

lsmod

Module                  Size  Used by    Tainted: P  
userman_mod            51600  4 
ath_pktlog             15776  0 
umac                  637696  1 ath_pktlog
ath_dev               200240  2 ath_pktlog,umac
ath_dfs                46128  2 umac,ath_dev
ath_rate_atheros       25440  3 ath_pktlog,umac,ath_dev
ath_hal               582992  4 ath_pktlog,umac,ath_dev,ath_rate_atheros
asf                     7632  4 umac,ath_dev,ath_dfs,ath_hal
adf                    13184  3 umac,ath_dev,ath_hal
aae                   107888  4 umac,ath_dev,ath_dfs,ath_hal
kdsldmod             1168720  9 userman_mod
drv_dsl_cpe_api       309104  2 
ifxmips_mei            36544  3 drv_dsl_cpe_api
ramzswap               15424  1 
lzo_decompress          1888  1 ramzswap
lzo_compress            1728  1 ramzswap
dect_io                10256  0 
avm_dect              216400  1 dect_io
capi_codec            341840  0 
isdn_fbox_fon5        727920  5 
pcmlink               378736  4 avm_dect,capi_codec,isdn_fbox_fon5
Piglet_noemif          30496  0 
rtc_avm                 3584  1 pcmlink
led_modul_Fritz_Box_HW189    68576  4 

processes

PID USER VSZ STAT COMMAND 1 root 1236 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [events/0] 5 root 0 SW [khelper] 8 root 0 SW [async/mgr] 22 root 0 SW [sync_supers] 23 root 0 SW [bdi-default] 25 root 0 SW [kblockd/0] 43 root 0 SW [kswapd0] 44 root 0 SW [aio/0] 53 root 0 SW [pm_info] 60 root 0 SWN [avmdebug] 86 root 0 SW [mtdblockd] 104 root 0 SW [l2tp] 108 root 0 SW [tffsd_mtd_0] 109 root 0 SW [avmnet_workqueu] 111 root 0 SW [avmnet_timer] 171 root 0 SW [cleanup_timer_f] 275 root 0 SWN [jffs2_gcd_mtd5] 280 root 0 SW [capi_pipew/0] 281 root 0 SW [capi_schedw/0] 282 root 0 SW [pcmlink_ctrl] 283 root 0 SW [capitransp] 286 root 0 SW< [avm_dect_thread] 287 root 0 SW [ksock tcp worke] 288 root 0 SW [ksock tcp serve] 373 root 1236 S < /sbin/udevd --daemon 374 root 1236 S < /sbin/udevd --daemon 375 root 1236 S < /sbin/udevd --daemon 389 root 2480 S /bin/configd 414 root 0 SW [RTT_Client] 422 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 430 root 2492 S dsl_monitor -d 431 root 2492 S dsl_monitor -d 432 root 2492 S dsl_monitor -d 434 root 2492 S dsl_monitor -d 440 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 441 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 442 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 443 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 444 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 445 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 563 root 0 SWN [dectuart_route] 567 root 2692 S avmipcd 571 root 3208 S l2tpv3d 577 root 12472 S ctlmgr 581 root 5108 S upnpd 584 root 0 SW [autbtex] 585 root 0 SW [ceocex_ne] 586 root 0 SW [pmex_ne] 587 root 0 SW [pmex_fe] 590 root 3948 S multid 602 root 2776 S upnpdevd 612 root 2588 S wland -B 617 root 4276 S dsld -i -n 625 root 4288 S pbd 626 root 4288 S pbd 628 root 4288 S pbd 629 root 4288 S pbd 635 root 12472 S ctlmgr 636 root 12472 S ctlmgr 637 root 12472 S ctlmgr 638 root 5724 S telefon a127.0.0.1 643 root 5724 S telefon a127.0.0.1 644 root 5724 S telefon a127.0.0.1 655 root 5796 S < voipd 664 root 1236 S /usr/sbin/inetd 671 root 1136 S /bin/run_clock -c /dev/tffs -d 683 root 1256 S -/bin/sh 1241 root 5108 S upnpd 1242 root 5108 S upnpd 1243 root 5108 S upnpd 1244 root 1412 S hostapd -B /etc/wpa2/WSC_ath0.conf 1262 root 3416 S usermand 1264 root 3268 S contfiltd 1312 root 1232 R ps w 1313 root 1232 R ps


mount

rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
tmpfs on /var type tmpfs (rw,relatime)
tmpfs on /dev type tmpfs (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/mtdblock5 on /data type jffs2 (rw,relatime)

disk free

ilesystem                Size      Used Available Use% Mounted on
/dev/root                10.2M     10.2M         0 100% /
tmpfs                    25.8M    600.0K     25.2M   2% /var
tmpfs                    25.8M     12.0K     25.8M   0% /dev
/dev/mtdblock5            2.0M    388.0K      1.6M  19% /data

ifconfig

adsl Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:2000 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ath0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:20 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:224 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:5447 (5.3 KiB) eth0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) guest Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:192.168.179.1 Bcast:192.168.179.255 Mask:255.255.255.0 inet6 addr: fe80::9ec7:a6ff:fea5:961e/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:368 (368.0 B) hotspot Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lan Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:192.168.178.1 Bcast:192.168.178.255 Mask:255.255.255.0 inet6 addr: fe80::9ec7:a6ff:fea5:961e/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:259 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:79305 (77.4 KiB) lan:0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:169.254.1.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:810 errors:0 dropped:0 overruns:0 frame:0 TX packets:810 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:311942 (304.6 KiB) TX bytes:311942 (304.6 KiB) wifi0 Link encap:UNSPEC HWaddr 9C-C7-A6-A5-96-20-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1012 errors:0 dropped:0 overruns:0 frame:0 TX packets:6241 errors:10 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:24 Memory:b8000000-b8010000


Kernel 5.4

  • check/remove → /openwrt/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/ar9_avm_fritz7312.dtsbootargs“nosmp”
  • make kernel_menuconfig → Kernel type → [*] MIPS MT SMP support & [*] SMT (multithreading) & [*] Dynamic FPU affinity → Exit & Save
  • make kernel_menuconfig → Device Drivers → Remoteproc drivers → [*] Support for Remote Processor subsystem → Exit & Save
  • additional: make menuconfig → Base system → busybox → [*] Customize busybox options → Process Utilities → top → [*] Accept keyboard commands & [*] Show CPU per-process usage percentage & [*]Show CPU global usage percentage & [*] SMP CPU usage display ('c' key) → Exit & Save
  • Build Imagemake V=s -jX ← set j to build system CPU cores + 1

Kernel 4.14

  • make kernel_menuconfig → Kernel type → [*] MIPS MT SMP support[*] SMT (multithreading) → Exit & Save
  • make menuconfig → Utilities → <*> irqbalance
  • check/remove → /openwrt/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/ar9_avm_fritz7312.dtsbootargs“nosmp”
  • additional: make menuconfig → Base system → busybox → Process Utilities → top → [*] Accept keyboard commands & [*] SMP CPU usage display ('c' key) → Exit & Save
  • Build Imagemake V=s -j3 ← set j to build system CPU cores + 1
  • additional: irqbalance autostart → boot up box and sshvi /etc/rc.local → press i add /usr/sbin/irqbalance → press ESC → press shift+: → press wq → press ENTERreboot

console login

ssh root@192.168.1.1
uci show network
network.atm=atm-bridge
network.atm.vpi='1'
network.atm.vci='32'
network.atm.encaps='llc'
network.atm.payload='bridged'
network.dsl=dsl
network.dsl.firmware='/lib/firmware/adsl.bin'
network.dsl.annex='b'
network.dsl.xfer_mode='atm'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.wan=interface
network.wan.ifname='nas0'
network.wan.proto='pppoe'
network.wan.ipv6='auto'
network.wan.username='Set_Username'
network.wan.password='Set_Password'
network.wan_dev=device
network.wan_dev.name='nas0'
network.wan_dev.macaddr='xx:xx:xx:xx:xx:xx'
network.wan6=interface
network.wan6.ifname='pppoe-wan'
network.wan6.proto='dhcpv6'

Annex: use A if not in germany

uci set network.dsl.annex='a'

TransferMode: try PTM if ATM is not working

uci set network.dsl.xfer_mode='ptm'

→ ADSL login data

uci set network.wan.username='Set_Username'
uci set network.wan.password='Set_Password'
uci commit
/etc/init.d/network reload
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1